Texas Instruments

OPA131UA - 4MHz Low-Bias FET Op Amp | Texas Instruments

MPN: OPA131UA ✓ چالاک
±18 V Vdss 50 pA maximum Id 8-pin SOIC Package
MOQ: 1 |

OPA131UA گشتی

The Texas Instruments OPA131UA is a single general-purpose FET-input operational amplifier with a 4 MHz gain-bandwidth product, 50 pA maximum input bias current, and 750 µA power consumption, housed in an 8-pin SOIC package. It supports a wide ±18 V supply range and provides a 10 V/µs slew rate for handling moderate-frequency signals with low distortion.

A FET-input operational amplifier is an analog signal-conditioning amplifier whose input stage uses field-effect transistors instead of bipolar input transistors. This architecture provides very low input bias current, making it appropriate for high-impedance sensors, photodiode amplifiers, precision measurement circuits, and audio preamplifiers. Within the broader hierarchy, the OPA131UA is an operational amplifier, analog IC, and semiconductor designed to amplify differential voltage signals.

The OPA131UA combines low input bias current with general-purpose dynamic performance. Its 4 MHz gain-bandwidth product supports useful bandwidth at moderate closed-loop gains, while the 10 V/µs slew rate supports faster large-signal transitions. Maximum input offset voltage is 750 µV, helping reduce static error in gain and feedback networks when precision matters.

The device operates from a wide ±18 V supply range, which provides flexibility in dual-supply instrumentation and higher-headroom single-supply systems when biasing is arranged correctly. Its FET input stage is the defining architectural feature: the 50 pA maximum bias current helps prevent source-loading errors in high-impedance sources and reduces input-current-induced voltage shifts.

Typical applications include precision signal conditioning, low-current sensor interfaces, analog measurement systems, audio preamplification, active filtering, and general-purpose analog signal chains. It is especially useful where conventional bipolar-input amplifiers may produce excessive input bias-current error but full rail-to-rail operation is not required.

Designers should verify input and output common-mode limits, supply polarity, output swing, and stability against the intended load before finalizing a circuit. Feedback-component placement and output-load configuration also require care because the 8-pin SOIC device must be supported by a stable compensation network and suitable board layout.

This product page combines manufacturer specifications, drop-in comparison guidance, application-oriented design notes, and practical considerations for engineers evaluating the OPA131UA in general-purpose analog designs.

جێگرەوەکانی جێگۆڕکێ بۆ OPA131UA — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ OPA131UA (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Product Type, Gain-Bandwidth Product, Slew Rate, Input Bias Current, Amplifier Type.

Texas Instruments
Product Type: Single general-purpose operational amplifier
بەراوردکردن لەگەڵ OPA131UA →
Texas Instruments
Amplifier Type: Single J-FET operational amplifier
بەراوردکردن لەگەڵ OPA131UA →
Texas Instruments
Product Type: General-purpose operational amplifier
Gain-Bandwidth Product: 8 MHz
Slew Rate: 20 V/µs
بەراوردکردن لەگەڵ OPA131UA →

OPA132UA

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-pin SOIC
Single operational amplifier · 5 pA nominal · 50 pA · 8 MHz · 20 V/µs · ±18 V · 130 dB with 600 Ω load · 500 µV

✓ بەردەستە

$3.6094 / یەکە

بینینی داتاشیت →

OPA131UA زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Product Type Single general-purpose FET-input operational amplifier
Number of Channels 1 channel
Gain-Bandwidth Product 4 MHz
Input Bias Current 50 pA maximum
Power Consumption 750 µA
Supply Voltage Range ±18 V
Slew Rate 10 V/µs
Input Offset Voltage 750 µV maximum
Input Stage Architecture FET input
پاکێج 8-pin SOIC
جۆری دامەزراندن Surface mount
Performance Grade Commercial and industrial temperature options
Capacitive Load Drive Excellent capacitive-load drive

ڕێکخستنی پینی OPA131UA

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
پین 1 NC — Not connected
پین 2 IN- — Inverting input
پین 3 IN+ — Noninverting input
پین 4 V- — Negative supply connection
پین 5 NC — Not connected
پین 6 OUT — Output
پین 7 V+ — Positive supply connection
پین 8 NC — Not connected

بەکارهێنانە باوەکان

OPA131UA گونجاوە بۆ 6 بەکارھێنانs: High-Impedance Sensor Signal Conditioning, Precision Analog Measurement Front End, Transimpedance Amplification, Audio Preamplification, Active Filtering and General-Purpose Amplification, Data Acquisition and Analog Interface.

🧩

High-Impedance Sensor Signal Conditioning

The OPA131UA fits low-current sensor interfaces because its FET input stage limits bias current to 50 pA maximum, reducing the voltage error produced by current flow through a high source impedance. Its 4 MHz gain-bandwidth product preserves useful response bandwidth, while the 10 V/µs slew rate supports faster signal transitions than many precision low-leakage amplifiers. Place the device close to the sensor or guarded electrode, maintain clean high-impedance routing, and confirm that input capacitance, offset voltage, noise, and output-swing requirements support the selected gain. The 750 µV maximum input offset voltage also helps limit static error after feedback-defined amplification.

🏭

Precision Analog Measurement Front End

The OPA131UA is appropriate for the gain and filtering stage of a precision measurement front end when source leakage must remain low. Its 50 pA maximum input bias current reduces errors associated with resistive sensors, and the 750 µV maximum offset voltage limits input-referred static error in closed-loop gain configurations. The 4 MHz bandwidth and 10 V/µs slew rate provide useful dynamic range for signals extending well above simple DC-only use. Engineer the feedback resistors and compensation capacitor for the target noise, accuracy, and stability goals, and keep sensitive input traces away from switching nodes and high-current return paths.

📷

Transimpedance Amplification

OPA131UA can serve as the input amplifier in a transimpedance circuit when a photodiode or other current-producing sensor requires low input bias current. The 50 pA maximum input current is the central benefit because it minimizes error across the feedback resistor and reduces sensor-loading effects. Its 4 MHz gain-bandwidth product and 10 V/µs slew rate provide useful bandwidth for moderate-speed events, but the total feedback resistance, sensor capacitance, and required rise time determine the actual stability margin. Use the manufacturer's recommended compensation network and guard the sensitive input node to limit leakage and surface contamination.

🎧

Audio Preamplification

The OPA131UA is suitable for low-level audio preamplification because its FET input stage provides 50 pA maximum bias current and its 10 V/µs slew rate offers useful large-signal capability. A 4 MHz gain-bandwidth product supports moderate audio-bandwidth closed-loop gains, including gain shaping in active filters or tone-control stages. Designers should review output swing, noise, and load drive against the selected operating point, especially when driving downstream audio circuitry. Stable feedback layout, short output routing, and adequate supply bypassing help preserve low distortion and predictable operation.

🔧

Active Filtering and General-Purpose Amplification

OPA131UA supports active-filter and general-purpose amplification tasks where a conventional bipolar-input amplifier would draw excessive bias current. Its 50 pA maximum input bias current helps preserve the behavior of high-value feedback networks, while 4 MHz bandwidth and 10 V/µs slew rate permit useful closed-loop response above the baseband region. The circuit must still account for amplifier stability, gain-bandwidth interaction, component tolerances, and the operating-point-dependent output swing. Prototype the noise and frequency-response target, then tune component values according to the manufacturer's guidance rather than relying only on nominal gain calculations.

🖥️

Data Acquisition and Analog Interface

The OPA131UA can condition analog inputs before conversion in a data-acquisition system where low input current protects source accuracy. Its 4 MHz gain-bandwidth product supports moderate-frequency signal paths, and the 10 V/µs slew rate allows the amplifier to follow rapid input changes without the severe slew limitation of much slower precision amplifiers. When driving an ADC, compare the amplifier's settling characteristics, output-noise behavior, and drive capability with the converter's acquisition requirements. Keep the feedback network compact, isolate sensitive inputs from digital return currents, and verify the complete chain for aliasing, stability, and full-scale headroom.

What is the OPA131UA?
The OPA131UA is a single general-purpose FET-input operational amplifier from Texas Instruments. It combines a 4 MHz gain-bandwidth product, 50 pA maximum input bias current, 750 µA power consumption, and a 10 V/µs slew rate in an 8-pin SOIC package. According to the Texas Instruments OPA131 product page, the OPAx131 family provides high performance at low cost for general-purpose analog applications.
What are the key specifications of OPA131UA that engineers should know?
The OPA131UA's principal specifications are 4 MHz gain-bandwidth product, 50 pA maximum input bias current, 750 µV maximum input offset voltage, 10 V/µs slew rate, and operation across a ±18 V supply range. Texas Instruments describes it as a single, general-purpose FET-input operational amplifier, making these ratings the core considerations for bandwidth, source loading, static error, and large-signal performance.
What is the operating voltage of OPA131UA?
The OPA131UA supports a wide supply range extending to ±18 V, as identified by Texas Instruments for the OPA131 series. The exact operating range should be confirmed in the manufacturer datasheet before applying the device to a new rail. Input common-mode voltage, output swing, and supply-current limits must also remain within their specified boundaries.
Why is the low 50 pA bias current of OPA131UA important?
The 50 pA maximum input bias current makes the OPA131UA suitable for high-impedance sources because the amplifier draws very little current from the signal source. Texas Instruments identifies the OPA131 as a FET-input amplifier, and its low-bias architecture helps reduce source-loading error. It is particularly useful for sensor interfaces, transimpedance paths, and precision measurement circuits.
Where can I download the OPA131UA datasheet PDF?
The official OPA131UA documentation is available from the Texas Instruments OPA131 product page, which links the family datasheet and ordering information. Start with the OPA131 manufacturer product page for the authoritative electrical characteristics, pin configuration, recommended operating conditions, and package drawings. The OPA131UA ordering page also identifies the exact 8-pin SOIC orderable device.
Where can I find the OPA131UA pinout?
The OPA131UA pin configuration is documented in the pin-description section of the Texas Instruments OPA131 datasheet. Because the device is a single amplifier in an 8-pin SOIC, the package diagram should be checked for offset and supply-pin locations before PCB routing. Use the manufacturer pin-description table when assigning each PCB land and test point.
Is OPA131UA suitable for high-impedance sensor interfaces?
Yes, the OPA131UA is well suited to high-impedance sensor interfaces because its FET input stage limits bias current to 50 pA maximum. This reduces the input-current error produced across a high source resistance. Its 4 MHz bandwidth and 10 V/µs slew rate also support moderate-speed signals, although sensor bandwidth, noise, capacitance, and output-swing requirements still determine the final gain and operating point.
What is the best drop-in replacement for OPA131UA?
The OPA132UA is the closest documented drop-in candidate in the 8-pin SOIC family, with matching 4 MHz bandwidth and 10 V/µs slew-rate figures. However, output-swing and other channel-specific ratings should be checked against the OPA131UA before substitution. Request a formal engineering review if the replacement drives an ADC, precision bridge, or safety-related circuit.
Can OPA132UA replace OPA131UA in an existing PCB?
The OPA132UA can be considered as a pin-compatible replacement because it uses the same 8-pin SOIC format and the published comparison identifies matching 4 MHz bandwidth and 10 V/µs slew-rate characteristics. Those matching values represent a 0% difference in those two parameters. Confirm output swing, common-mode range, offset, bias current, noise, and stability requirements before approving the substitution.
OPA131UA vs OPA132UA - which is better for a precision signal chain?
Choose the OPA131UA when its specified output-swing and general-purpose characteristics satisfy the signal chain, and choose the OPA132UA only after confirming that its output behavior offers a needed advantage. The documented bandwidth and slew-rate match is exact at 4 MHz and 10 V/µs, respectively. For precision designs, compare output swing, offset voltage, noise, and input bias-current limits in the manufacturer documentation.
When should I choose OPA131UA over OPA132UA?
Choose the OPA131UA when it is the validated device for the required input common-mode range, output swing, noise performance, and stability behavior. The OPA132UA has the same documented 4 MHz bandwidth and 10 V/µs slew rate, so those figures alone do not establish a meaningful preference. Keep the OPA131UA when its existing circuit qualification, biasing, and production configuration are already proven.
Is OPA131UA the same as OPA132UA?
No. The OPA131UA and OPA132UA are related single-amplifier devices in the 8-pin SOIC family, but their channel-specific characteristics are not identical. Their published bandwidth and slew rate both match at 4 MHz and 10 V/µs, while output-swing behavior and other detailed electrical characteristics may differ. Use the pinout and complete electrical tables to determine interchangeability.
What is the best equivalent for OPA131UA from another manufacturer?
No cross-manufacturer 8-pin SOIC equivalent is established by the cited replacement records. The available comparison results identify OPA132UA, a Texas Instruments device, but they do not verify a pin-compatible competitor with quantified matching ratings. An equivalent should not be selected solely from gain-bandwidth product or package similarity; input bias current, output swing, common-mode range, noise, and stability must all meet the circuit requirements.
Where can I buy OPA131UA online?
Use the Request a Quote form on this page to request the current availability, lead time, and minimum order quantity for the OPA131UA. Quote requests ensure that the exact 8-pin SOIC order code and required quantity are reviewed together. Current commercial terms should be confirmed through the form because market availability and lead times can change.
What is the price of OPA131UA?
The current OPA131UA commercial quote is provided through the Request a Quote form on this page. Submit the required quantity and delivery destination to receive current terms for the exact Texas Instruments order code. The quoted response should also confirm package form, authorized sourcing conditions, and the applicable production lead time.
What is the lead time for OPA131UA and is it in stock?
The current lead time and stock position for OPA131UA should be obtained through the Request a Quote form on this page. The exact quantity and required package form affect the response, so include that information with the request. Do not treat a general distributor listing as confirmation of current stock for the particular order configuration.

داتای سەرچاوەی ئەندازیاری بۆ OPA131UA — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the OPA131UA for general-purpose designs that need a single FET-input operational amplifier with 50 pA maximum bias current, 4 MHz bandwidth, 10 V/µs slew rate, and operation from a ±18 V supply capability. It is especially attractive for high-impedance sensors, precision measurement front ends, transimpedance circuits, and moderate-bandwidth audio stages. Consider the OPA132UA when an existing qualified circuit can benefit from its channel-specific output behavior, but review output swing and the complete electrical tables because the documented bandwidth and slew rate are identical. No cross-manufacturer substitute has been established with complete package, pinout, and parametric verification, so changing manufacturers requires an independent engineering review. For either device, confirm input common-mode range, output swing, stability, noise, offset, supply current, and PCB pin assignments before production release.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە OPA132UA
Brand Texas Instruments Texas Instruments
Package 8-pin SOIC 8-pin SOIC
Number of Channels 1 channel 1 channel
Gain-Bandwidth Product 4 MHz 4 MHz
Slew Rate 10 V/µs 10 V/µs

جیاکەرەوە سەرەکییەکان

  • Very low input bias current supports high-impedance sources (بەراورد بەOPA132UA)
  • Documented general-purpose dynamic performance (بەراورد بەOPA132UA)
  • Low-power single-amplifier configuration (بەراورد بەOPA132UA)

تێبینییەکانی دیزاین

Route the OPA131UA input and feedback paths as short, compact traces, especially in high-impedance or transimpedance applications. Keep the noninverting input away from switching nodes, inductors, and exposed pad connections. Guarding techniques can help control surface leakage, but the guard geometry should not create an unintended low-resistance path around the input source. Confirm every land and supply connection against the 8-pin SOIC pin description in the manufacturer datasheet.

Do not treat the 4 MHz gain-bandwidth product as the usable bandwidth at every closed-loop gain. Higher-noise gain settings provide less bandwidth, and the required precision and settling behavior may reduce the practical operating frequency further. Also verify output swing for the selected supply voltage because the stated ±18 V capability does not guarantee rail-to-rail output at every supply condition.

Place power-supply bypass capacitors close to the positive and negative supply pins, using the capacitance and layout recommendations in the manufacturer datasheet. Keep the feedback loop compact and isolate the sensitive input node from ground-current returns associated with digital or switching circuitry. When driving a capacitive ADC input, verify settling and stability rather than assuming the amplifier can drive the load directly.

The OPA131UA's low input bias current helps preserve high-impedance signals, but it does not eliminate EMI coupling. Maintain a continuous ground reference, minimize exposed sensitive-node area, and keep input wiring away from antenna-like copper structures. If the source is remote, consider guarding or a shielded connection and evaluate the complete system's noise and interference performance.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The manufacturer information confirms commercial and industrial performance grades, but explicit RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not identified for this order code. AEC-Q100 is not applicable because the OPA131UA is not identified as an automotive-qualified device.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

OPA131UA datasheet OPA131UA datasheet pdf OPA131UA pinout OPA131UA SOIC-8 footprint OPA131UA 50 pA bias current OPA131UA 4 MHz bandwidth Texas Instruments OPA131UA OPA131UA equivalent OPA131UA replacement OPA131UA vs OPA132UA OPA131UA high impedance sensor OPA131UA price OPA131UA stock Where to buy OPA131UA What is the lead time for OPA131UA

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments OPA131 OPA131UA OPA132UA operational amplifier FET-input operational amplifier analog amplifier analog integrated circuit semiconductor low-dropout input bias current input bias current gain-bandwidth product slew rate input offset voltage common-mode voltage range output swing 8-pin SOIC SOIC package family surface-mount package SMD package precision signal conditioning high-impedance sensor interface transimpedance amplifier data acquisition active filter
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ