OPA227PA - Low-Noise Precision Op Amp | Texas Instruments
MPN: OPA227PA ✓ چالاکOPA227PA گشتی
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs while using negative feedback to control gain, bandwidth, and output behavior. Within the broader semiconductor hierarchy, OPA227PA is a precision operational amplifier, a linear amplifier and signal-conditioning IC. This category is used in instrumentation, sensor interfaces, laboratory equipment, audio electronics, and precision analog systems where low noise and small input-offset errors influence measurement accuracy.
The OPA227PA combines a 10 µV input-offset voltage with 3 nV/√Hz noise density and a 10 V/µs slew rate. Its 138 dB CMRR indicates strong rejection of common-mode signals, while the 5 µs settling specification supports accurate operation after rapid input or output transitions. The 18 V maximum supply voltage cited in product data provides a useful operating limit for conventional bipolar or dual-supply analog designs.
Texas Instruments describes the OPAx227 family as a pin-for-pin replacement for the industry-standard OP27 and OP37, with substantial performance improvements. This relationship makes pin compatibility an important design consideration when replacing older precision amplifiers. Because the OPA227PA is a single-amplifier version, board designers should confirm the exact pin functions in the manufacturer datasheet before modifying a board that originally carried a different package or channel configuration.
Typical applications include precision sensor amplifiers, low-level current-to-voltage converters, laboratory measurement front ends, audio preamplifiers, and buffered analog signal chains. In each case, the low 3 nV/√Hz noise density reduces the input-referred noise contribution, while the 10 µV offset specification limits signal-chain error near the zero-input operating point. The 8-pin PDIP package also facilitates prototyping, socketed assemblies, and through-hole industrial equipment.
For stable operation, place input and feedback components close to the amplifier pins, maintain the required bypass-capacitor arrangement, and avoid long PCB traces in high-gain feedback loops. Input and output voltages must remain within the device's common-mode and supply limits. Stable operation also depends on maintaining adequate phase margin with the selected gain and load, particularly when driving capacitive loads or operating at high closed-loop gain.
This product page consolidates the manufacturer specifications, package details, application guidance, drop-in replacement context, and practical design notes needed to evaluate OPA227PA. It also distinguishes direct footprint compatibility from broader functional similarity, helping engineers identify the correct replacement while protecting signal-integrity and measurement performance.
جێگرەوەکانی جێگۆڕکێ بۆ OPA227PA — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ OPA227PA (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Slew Rate, Mounting Type, Amplifier Type, Number of Circuits, Operating Temperature Range.
OPA227P
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →OP27KP
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
OP27GP
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
OP37KP
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
OP37GP
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
OPA227PA زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Amplifier Type | Single precision operational amplifier |
| Number of Circuits | 1 circuit |
| چڕیی دەنگ | 3 nV/√Hz |
| Gain-Bandwidth Product | 8 MHz |
| Slew Rate | 10 V/µs |
| Settling Time | 5 µs |
| Input Offset Voltage | 10 µV maximum |
| Common-Mode Rejection Ratio | 138 dB |
| Maximum Supply Voltage | 18 V |
| مەودای پلەی گەرمیی کارکردن | -40 °C to 85 °C |
| Package Type | PDIP-8 |
| ژمارەی پینەکان | 8 pins |
| جۆری دامەزراندن | Through-hole |
ڕێنمایی ڕێکخستنی پینی OPA227PA pdip-8
ڕێکخستنی پین بۆ OPA227PA (پاکێجی pdip-8). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ OPA227PA.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
OPA227PA گونجاوە بۆ 6 بەکارھێنانs: Precision Sensor Signal Conditioning, Laboratory Measurement Front End, Low-Level Audio Preamplifier, Precision Current-to-Voltage Conversion, Industrial Analog Signal Conditioning, Buffered Voltage Reference.
Precision Sensor Signal Conditioning
OPA227PA fits low-level sensor front ends where the 3 nV/√Hz noise density limits the amplifier's input-referred noise contribution and the 10 µV maximum offset voltage helps preserve accuracy near the sensor's zero point. Place the amplifier directly after the sensor and conversion resistor, with short input traces and symmetric feedback resistors to reduce parasitic pickup. The 10 V/µs slew rate supports reasonably fast sensor signals without forcing a wide-bandwidth design. Check the sensor output range against the input common-mode limits, and avoid extremely high source impedances that can increase bias-current error and offset imbalance.
پێشنیارکراو
Laboratory Measurement Front End
OPA227PA is suitable for laboratory and test-equipment input stages requiring a combination of low noise, low offset, and conventional 8-pin through-hole construction. Its 3 nV/√Hz noise density, 138 dB documented CMRR, and 10 µV maximum input offset are useful when amplifying small differential signals from sensors, bridges, or laboratory sources. The 8 MHz gain-bandwidth product and 10 V/µs slew rate allow moderate closed-loop bandwidth at practical gains. For high-gain operation, verify phase margin and settling behavior with the intended feedback network and avoid long unprotected input leads that increase noise pickup.
پێشنیارکراو
Low-Level Audio Preamplifier
OPA227PA can serve in low-level audio preamplifier and line-stage positions where input-referred noise and offset distortion are important. The 3 nV/√Hz noise density supports quiet amplification of microphone-level or instrument-level signals, while the 10 V/µs slew rate provides ample headroom for ordinary audio bandwidth. An 8-pin PDIP package is useful in hand-built audio controllers, active preamplifiers, and educational equipment. Keep the input impedance high enough to avoid loading the source, and place the feedback network and gain-setting resistors close to the package to reduce hum, RF pickup, and unintended oscillation.
پێشنیارکراو
Precision Current-to-Voltage Conversion
OPA227PA is appropriate for precision current-to-voltage conversion when the source current is small and measurement resolution depends on low offset and noise. The 10 µV maximum input-offset voltage limits a major error source at the transimpedance node, and the 3 nV/√Hz figure supports low-noise conversion of sensor currents. A conventional inverting configuration can use the device in an 8-pin PDIP socket on a through-hole analog board. Select the feedback resistor carefully because its Johnson noise and parasitic capacitance influence both signal gain and stability; verify the complete transimpedance bandwidth and output-swing limits at the selected supply voltage.
پێشنیارکراو
Industrial Analog Signal Conditioning
OPA227PA is suitable for industrial analog conditioning where a low-noise single amplifier must operate from dual or suitably bounded single supplies. Its documented 18 V maximum supply rating accommodates conventional ±15 V or lower single-supply systems, while 138 dB CMRR helps reject common-mode voltage on long sensor cables. The 10 V/µs slew rate and 5 µs settling specification provide useful response for moderately fast control or monitoring signals. Add input protection for industrial transients, maintain common-mode headroom at every operating point, and use a grounded reference strategy to prevent ground offsets from degrading the measured signal.
پێشنیارکراو
Buffered Voltage Reference
OPA227PA can buffer a low-current reference node when the source cannot directly drive the intended load. Its 10 µV offset and 3 nV/√Hz noise density can help preserve the integrity of a small reference signal, while the 10 V/µs slew rate improves transient response compared with a passive buffer. The 8-pin PDIP format is convenient for prototype and through-hole instrumentation. Choose the gain, load capacitance, and output range so the amplifier remains stable, and avoid using the op-amp input as a precision reference node unless its bias-current contribution has been included in the error budget.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ OPA227PA — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | OPA227P | OP27KP | OP27GP | OP37KP | OP37GP |
|---|---|---|---|---|---|---|
| Package | PDIP-8 | PDIP-8 | PDIP-8 | PDIP-8 | PDIP-8 | PDIP-8 |
| Brand | Texas Instruments | Texas Instruments | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
جیاکەرەوە سەرەکییەکان
- Lower documented noise than the legacy precision-amplifier cross-reference (بەراورد بەOP27KP)
- Fast settling for a through-hole precision amplifier (بەراورد بەOP37KP)
- Single-amplifier precision design with conventional PDIP construction (بەراورد بەOP27GP)
- Documented 8 MHz bandwidth and 3 nV/√Hz noise performance (بەراورد بەOP37GP)
تێبینییەکانی دیزاین
Keep the non-inverting input, inverting input, feedback resistor, and output return path compact. OPA227PA's 3 nV/√Hz noise density is valuable only when the PCB does not add comparable pickup. Use a grounded guard or shield around sensitive input nodes, avoid running the input beside switching nodes, and place the feedback loop close to the amplifier. If the source impedance is high, account for bias-current error and the interaction between source capacitance, gain, and stability rather than relying on the nominal noise specification alone.
Do not substitute the package appearance alone. Although Texas Instruments identifies OPAx227 as pin-for-pin compatible with OP27 and OP37 devices, the OP27 and OP37 families have different compensation targets. Verify open-loop gain, phase margin, offset, bias current, common-mode range, supply limits, and the handling of the offset-null pins for the exact candidate suffix. A board designed around OP37 compensation may require different external compensation or gain settings than an OPA227PA implementation.
Design the supply rails with the documented 18 V maximum operating voltage in mind and include adequate headroom for startup tolerance, transient excursions, and component tolerances. Decouple each supply pin near the package according to the manufacturer guidance. For dual-supply operation, verify output swing across the complete signal range and ensure the input common-mode voltage remains valid during startup. A precision amplifier cannot improve accuracy if its supply bypass, grounding, or reference arrangement introduces noise and offset.
For a precision gain stage, use matched resistor networks where practical and avoid adding copper that changes stray capacitance around high-impedance nodes. A 10 V/µs slew rate and 8 MHz gain-bandwidth product provide fast response, but excessive loop gain or capacitive loading can still reduce stability. Check the closed-loop response at the intended gain, test representative load capacitances, and add an isolation resistor close to the output if capacitive drive requires it.
زانیاری پابەندبوون
The OPA227PA is a general-purpose precision operational amplifier, but explicit RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not found in the manufacturer pages reviewed. AEC-Q100 is not applicable to this general-purpose commercial part designation.