OPA353UA - 44 MHz RRIO Op Amp | Texas Instruments
MPN: OPA353UA ✓ چالاکOPA353UA گشتی
A rail-to-rail input and output operational amplifier, commonly called an RRIO amplifier, accepts input signals near the positive and negative supply rails while maintaining an output that approaches the available supply range. This makes the OPA353 suitable for low-voltage systems in which the useful signal can occupy much of the available analog headroom. It belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors.
The OPA353 combines a 44 MHz gain-bandwidth product with low input noise of 7 nV/√Hz and a slew rate of 22 V/µs. These characteristics support accurate amplification of small signals while also providing sufficient bandwidth for higher-speed instrumentation. Its rail-to-rail architecture simplifies buffering, level translation, and sensor-amplifier designs operated from a single low-voltage supply.
This single-amplifier device is optimized for low-voltage, single-supply operation. When configured with a noise gain of 1 V/V, its closed-loop bandwidth reaches 44 MHz. The 7 nV/√Hz noise density makes the device relevant to low-level analog front ends, while the 22 V/µs slew rate helps preserve large-signal response during fast transitions.
Typical applications include sampling analog-to-digital converter input drivers, low-noise signal conditioning, portable instrumentation, audio and communication interface circuits, and general-purpose rail-to-rail buffers. The 8-pin SOIC package supports conventional PCB assembly while keeping the device footprint compact.
Designers should verify the input common-mode range, output swing, output-current capability, stability, and noise performance against the actual supply voltage and load. Decoupling and short feedback paths help preserve the intended bandwidth and reduce parasitic effects in high-gain layouts.
This page organizes the OPA353UA technical characteristics, drop-in alternatives, application guidance, and design considerations into a practical engineering reference for evaluating the device in low-voltage precision and high-speed analog circuits.
جێگرەوەکانی جێگۆڕکێ بۆ OPA353UA — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ OPA353UA (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Gain-Bandwidth Product, Amplifier Type, Input Common-Mode Range, Supply Type.
OPA350UA
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →OPA351UA
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
OPA352UA
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
OPA353UA زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Amplifier Type | Single operational amplifier |
| Maximum Supply Voltage | 5.5 V |
| Gain-Bandwidth Product | 44 MHz |
| Input Voltage Noise Density | 7 nV/√Hz |
| Slew Rate | 22 V/µs |
| پاکێج | 8-pin SOIC |
| جۆری دامەزراندن | Surface mount |
ڕێنمایی ڕێکخستنی پینی OPA353UA 8-pin soic
ڕێکخستنی پین بۆ OPA353UA (پاکێجی 8-pin soic). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ OPA353UA.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
OPA353UA گونجاوە بۆ 6 بەکارھێنانs: Sampling ADC Input Driver, Low-Noise Sensor Signal Conditioning, Portable Instrumentation, Communications Interface Buffer, Audio Preamplifier, General-Purpose Rail-to-Rail Buffer.
Sampling ADC Input Driver
The OPA353UA fits low-voltage ADC front ends because its 44 MHz gain-bandwidth product and 22 V/µs slew rate can preserve signal amplitude and phase through a high-speed sampling interface. Place the amplifier as a voltage follower or low-gain buffer when the ADC requires a low-impedance source and rail-to-rail input operation. Confirm the ADC input range, settling time, capacitive loading, and required noise gain against the manufacturer curves before finalizing the filter and bypass network.
پێشنیارکراو
Low-Noise Sensor Signal Conditioning
The OPA353UA is appropriate for conditioning small sensor signals because its 7 nV/√Hz input noise density limits the amplifier's own contribution to wideband measurement noise. Its rail-to-rail input behavior can also make more of the sensor's output range usable in a compact 5.5 V system. Use a low closed-loop gain when bandwidth and stability are more important than noise gain, and keep the sensor return path and supply references clean to prevent additional noise from entering the measurement chain.
پێشنیارکراو
Portable Instrumentation
The OPA353UA supports portable measurement systems that combine low supply voltage with meaningful analog bandwidth. Its maximum 5.5 V supply supports compact single-supply operation, while the 44 MHz gain-bandwidth product handles signals beyond the range of a typical precision-only amplifier. The device is especially useful for buffering moderate-bandwidth sensors and converting conditioned outputs into ADC inputs. Low-power system design should still account for the amplifier's supply current and the thermal limits of the selected PCB footprint.
پێشنیارکراو
Communications Interface Buffer
The OPA353UA can serve as a high-speed interface buffer in low-voltage communications equipment where short propagation delay and adequate slew performance are important. Its 22 V/µs slew rate and 44 MHz bandwidth reduce distortion when passing moderate-amplitude digital or reconstructed analog signals. Rail-to-rail input and output behavior improves signal utilization near the supply rails. The receiving circuit's input capacitance, output-load limits, and timing requirements should be checked because high-speed edge rates can increase capacitive-load sensitivity.
پێشنیارکراو
Audio Preamplifier
The OPA353UA is useful in low-level audio preamplifier and line-driver stages that require more bandwidth than a general-purpose precision amplifier. Its 7 nV/√Hz input noise density supports low-noise amplification, and the 44 MHz gain-bandwidth product provides wide headroom for gain and filtering. The rail-to-rail architecture is valuable in single-supply audio circuits with limited signal swing. Headroom and distortion performance must be evaluated at the actual output amplitude because both are strongly influenced by load, frequency, and supply voltage.
پێشنیارکراو
General-Purpose Rail-to-Rail Buffer
The OPA353UA works as a rail-to-rail buffer when a signal source needs a low output impedance without adding a large amount of noise. Its 44 MHz bandwidth and 22 V/µs slew rate make it more responsive than conventional low-speed buffers, while the 5.5 V maximum supply supports compact systems. Use it between high-impedance sensors, external filters, or converters and downstream circuitry. Verify output-current capability and stability with the intended load, particularly when driving long PCB traces or capacitances above the standard test conditions.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ OPA353UA — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | OPA350UA | OPA351UA | OPA352UA |
|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Count | 1 | 1 | 1 | 1 |
| Gain-Bandwidth Product | 44 MHz | Lower-bandwidth family member | 44 MHz | 44 MHz |
| Input Common-Mode Range | Rail-to-rail input | Rail-to-rail input | Rail-to-rail input | Rail-to-rail input |
| Output Common-Mode Range | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output |
| Special Qualification | General-purpose | General-purpose | General-purpose | General-purpose |
جیاکەرەوە سەرەکییەکان
- Higher-bandwidth same-family alternative (بەراورد بەOPA350UA)
- Low-noise high-speed combination (بەراورد بەOPA351UA)
- Rail-to-rail signal-path utilization (بەراورد بەOPA352UA)
تێبینییەکانی دیزاین
Keep the feedback loop short and place the op-amp input, output, and decoupling components close to their corresponding pins. High closed-loop gain amplifies parasitic capacitance and board leakage, while long traces can add phase lag that affects stability. Route supply and ground planes to minimize impedance, avoid sharing narrow return paths with noisy digital circuits, and use a solid ground reference beneath the analog section where the board construction permits.
Do not treat a common SOIC footprint as proof of electrical drop-in compatibility. Before substituting OPA350UA, OPA351UA, or OPA352UA, compare supply range, input common-mode limits, output swing, output-current capability, noise, slew rate, stability, and the exact pin-description table. The OPA353UA operates with a maximum 5.5 V supply, so input or output excursions beyond the selected rail would also invalidate an assumed replacement.
The 44 MHz gain-bandwidth product and 22 V/µs slew rate make trace, connector, and load capacitance increasingly important. Estimate the maximum expected input transition rate and compare it with the device's slew-rate capability, then check the load against the manufacturer stability and output-current guidance. When driving an ADC, include the converter's acquisition kickback and input capacitance in the settling analysis rather than relying only on nominal amplifier bandwidth.
زانیاری پابەندبوون
No specific environmental or automotive qualification statements are identified for OPA353UA.