Texas Instruments

OPA642P - 400MHz Wideband Op Amp | Texas Instruments

MPN: OPA642P ✓ چالاک
±5.5 V Vdss ±60 mA Id 8-pin PDIP Package 5 MHz Speed
MOQ: 1 |

OPA642P گشتی

The Texas Instruments OPA642P is a wideband, low-distortion, low-gain operational amplifier with a 400 MHz gain-bandwidth product, 2.7 nV/√Hz input-noise density, and operation from ±5.5 V, housed in an 8-pin PDIP package. It also provides 95 dB open-loop gain, 90 dB common-mode rejection, 0.01% 12-bit settling, and ±60 mA output-current capability. These characteristics position the OPA642P as a high-speed voltage-feedback amplifier for signal-chain, measurement, and communications equipment.

An operational amplifier is a high-gain differential amplifier whose externally selected feedback network determines its closed-loop gain. The OPA642P belongs to the voltage-feedback operational-amplifier family within analog signal-chain ICs and power-management-adjacent semiconductor categories. Unlike a general-purpose precision amplifier optimized for low offset and low bias current, this device emphasizes bandwidth, slew capability, low distortion, and rapid settling.

Key features include a 400 MHz gain-bandwidth product for high closed-loop bandwidth, 2.7 nV/√Hz input-noise density for low-noise signal conditioning, and a ±5.5 V supply capability. The listed 5 MHz low-distortion figure supports broadband applications requiring low signal corruption. Open-loop gain of 95 dB and common-mode rejection of 90 dB improve accuracy and rejection of common-mode disturbances.

The device achieves 0.01% settling within the manufacturer-defined 12-bit settling test, making it relevant to instrumentation and signal-processing paths where usable resolution depends on rapid convergence after a step input. Its ±60 mA output-current capability gives it more drive than a basic low-power amplifier, although external load and stability requirements still determine the usable output amplitude. The architecture is explicitly suited to low-gain, high-speed voltage-feedback operation.

Typical applications include video-signal conditioning, communications receivers, high-speed instrumentation, active filters, data-conversion interfaces, and clock or pulse-shaping circuits. The 400 MHz bandwidth is particularly useful when preserving nanosecond-scale signal content, while the low-noise and low-distortion characteristics help maintain fidelity in wideband analog paths.

Designers should pay close attention to supply bypassing, output loading, feedback-component selection, and stability. Wideband amplifiers require short, low-inductance supply connections and carefully placed compensation or decoupling capacitors. The 8-pin PDIP package is also larger than modern surface-mount packages, so its mechanical footprint and lead spacing must be confirmed before using it in a new PCB design.

This page consolidates the verified manufacturer and distributor information for the OPA642P, adds package-aware engineering guidance, and distinguishes same-family alternatives by function and gain configuration. It also records unresolved electrical details explicitly rather than substituting guessed values, enabling more reliable design and sourcing decisions.

جێگرەوەکانی جێگۆڕکێ بۆ OPA642P — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ OPA642P (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Product Type, Common-Mode Rejection Ratio, Input Voltage Noise Density, Slew Rate.

Texas Instruments
Product Type: Voltage-feedback operational amplifier
Common-Mode Rejection Ratio: 85 dB
Input Voltage Noise Density: 2.9 nV/√Hz
بەراوردکردن لەگەڵ OPA642P →
Texas Instruments
Package: 8-pin PDIP, 0.300 inch (7.62 mm) pitch
بەراوردکردن لەگەڵ OPA642P →
Texas Instruments
Package: 8-pin PDIP (P)
Input Voltage Noise Density: 2.3 nV/√Hz
Slew Rate: 1000 V/µs
بەراوردکردن لەگەڵ OPA642P →

OPA640P

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 8-pin PDIP
Voltage-feedback operational amplifier · 1 circuit · 1.3 GHz · Unity-gain stable · 2.9 nV/√Hz · 85 dB · 350 V/µs · 10 MHz

پەیوەندی بۆ نرخ

بینینی داتاشیت →

OPA641P

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 8-pin PDIP
Same 8-pin PDIP family footprint and voltage-feedback architecture; the nominal +2 gain configuration is 100% higher than OPA642P's +1 configuration.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

OPA642PB

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-pin PDIP
Wideband, low-distortion, low-gain operational amplifier · Single voltage-feedback operational amplifier · ±4.5 V to ±5.5 V · 9 V to 11 V · 90 dB · 25 uA · 70 uA · 1 circuit

پەیوەندی بۆ نرخ

بینینی داتاشیت →

OPA643P

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 8-pin PDIP
Texas Instruments (Burr-Brown) · Voltage Feedback · 1 · 800 MHz · 1000 V/µs · 2.3 nV/√Hz · 5 MHz · ≥ 3

پەیوەندی بۆ نرخ

بینینی داتاشیت →

OPA644P

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 8-pin PDIP
Same 8-pin PDIP family footprint and voltage-feedback architecture; the nominal +10 gain configuration is 900% higher than OPA642P's +1 configuration.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

OPA642P زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Product Type Wideband, low-distortion, low-gain operational amplifier
Amplifier Topology Single voltage-feedback amplifier
Number of Circuits 1 circuit
Gain-Bandwidth Product 400 MHz
ڤۆڵتیەی دابینکردن ±5.5 V
Open-Loop Gain 95 dB
Common-Mode Rejection Ratio 90 dB
Input Noise Density 2.7 nV/√Hz
Low-Distortion Frequency 5 MHz
Settling Performance 12-bit settling to 0.01%
زۆرترین ئێستای دەرچوون ±60 mA
پاکێج 8-pin PDIP
ژمارەی پین 8 pins
جۆری دامەزراندن Through-hole

ڕێنمایی ڕێکخستنی پینی OPA642P 8-pin pdip

ڕێکخستنی پین بۆ OPA642P (پاکێجی 8-pin pdip). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.

نەخشەی پینئاوتی پاکێجی 8-pin pdip بۆ OPA642P

هیچ داتای وردی پینئاوت بەردەست نییە بۆ OPA642P.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

OPA642P گونجاوە بۆ 6 بەکارھێنانs: Wideband Video Signal Conditioning, Communications Receiver Front End, High-Speed Instrumentation, Active Filter Design, Data Conversion Interface, Clock and Pulse Signal Conditioning.

📺

Wideband Video Signal Conditioning

The OPA642P fits wideband video signal conditioning because its 400 MHz gain-bandwidth product preserves high-frequency content and its manufacturer data identifies low distortion at 5 MHz. The 95 dB open-loop gain can support accurate closed-loop operation around low gain settings, while the 2.7 nV/√Hz input-noise density helps limit added noise. In a practical video path, the device is placed between a source and a downstream buffer or converter, using short feedback paths and locally placed bypassing. The main design constraint is maintaining stability while driving the next stage's input capacitance and cable loading.

🌐

Communications Receiver Front End

The OPA642P is suitable for communications receiver front-end amplification because the 400 MHz gain-bandwidth product supports wideband signal paths and the 90 dB common-mode rejection helps suppress common-mode interference. Its 2.7 nV/√Hz input-noise density is valuable when preserving weak received signals, and the 0.01% 12-bit settling characteristic supports data-acquisition interfaces. Place the amplifier close to the source to minimize parasitic capacitance, use short ground returns, and select feedback resistors that preserve the intended closed-loop bandwidth. Output-current capability reaches ±60 mA, though the actual usable swing remains dependent on load and supply conditions.

🏭

High-Speed Instrumentation

The OPA642P can serve high-speed instrumentation when the measurement chain must settle rapidly and retain small-signal fidelity. The manufacturer reports 0.01% 12-bit settling, a 400 MHz gain-bandwidth product, and 2.7 nV/√Hz input noise, giving designers useful starting points for acquisition and buffer circuits. It is placed close to the transducer or converter output to minimize cable noise and capacitance, followed by a carefully routed feedback network. Because the device is optimized for speed rather than micropower, its supply demand and thermal behavior must be evaluated within the complete measurement system.

🔧

Active Filter Design

The OPA642P is appropriate for active filtering when a filter requires wide bandwidth and low distortion around 5 MHz. Its 400 MHz gain-bandwidth product provides substantial closed-loop bandwidth in a low-gain topology, while the 95 dB open-loop gain can improve closed-loop accuracy compared with a lower-gain amplifier. The amplifier is commonly positioned around a precision RC network with short component leads and a ground plane connected beneath the signal path. Component tolerances, parasitic capacitance, and the intended closed-loop gain must be evaluated together because the very wide bandwidth can amplify layout-related instability.

🖥️

Data Conversion Interface

The OPA642P can be used as the interface amplifier around a high-speed analog-to-digital or digital-to-analog converter when the system needs rapid settling and low added noise. Its 0.01% 12-bit settling behavior and 400 MHz gain-bandwidth product are directly relevant to acquisition timing, while 2.7 nV/√Hz input-noise density supports low-level input ranges. Position the amplifier next to the converter's supply and signal pins, use very short traces, and terminate unused inputs appropriately. The design must still reconcile converter kickback, capacitive loading, and the amplifier's high-frequency stability requirements.

⚡

Clock and Pulse Signal Conditioning

The OPA642P is suitable for clock and pulse conditioning because its 400 MHz gain-bandwidth product supports rapid edge handling and the reported 0.01% 12-bit settling indicates fast convergence after transitions. The low-noise architecture can preserve signals when source impedance and amplitude leave little margin, while the ±60 mA output-current capability helps drive downstream logic or termination networks. Keep the feedback loop compact, terminate the output according to the edge rate, and avoid long traces that add inductance. Output-amplitude and timing checks remain necessary because pulse duty-cycle distortion also depends on the connected load and supply rails.

What is the OPA642P?
The OPA642P is a single wideband, low-distortion, low-gain voltage-feedback operational amplifier from Texas Instruments. According to the manufacturer datasheet, it provides a 400 MHz gain-bandwidth product, 2.7 nV/√Hz input-noise density, 95 dB open-loop gain, and operation from ±5.5 V in an 8-pin PDIP package. It is intended for high-speed analog signal paths rather than precision, micropower, or energy-efficient applications.
What are the key specifications of OPA642P that engineers should know?
The OPA642P combines a 400 MHz gain-bandwidth product, 2.7 nV/√Hz input-noise density, 90 dB common-mode rejection, and 0.01% 12-bit settling in an 8-pin PDIP package. According to the Texas Instruments datasheet, it also supports a ±5.5 V supply and ±60 mA output current. These figures make the amplifier suitable for wideband signal conditioning, communications, instrumentation, filters, and data-conversion interfaces where bandwidth and settling speed are more important than low quiescent current.
What is the gain-bandwidth product of OPA642P?
The OPA642P has a 400 MHz gain-bandwidth product according to the Texas Instruments manufacturer datasheet. This value indicates the relationship between closed-loop bandwidth and the selected noise gain, making the device suitable for low-gain, high-speed signal conditioning. Actual bandwidth also depends on feedback-network impedance, PCB routing, output loading, supply decoupling, and the stability method selected for the intended closed-loop gain.
What supply voltage does OPA642P require?
The OPA642P operates from a ±5.5 V supply, as stated in the Texas Instruments manufacturer datasheet. This makes it suitable for dual-supply analog systems centered on ground. The available verified information does not state the complete allowable supply range or total supply-voltage limit, so those values remain [DATA_NEEDED]. Designers should not infer additional operating limits beyond those explicitly documented before checking the original datasheet.
Where can I download the OPA642P datasheet PDF?
The OPA642P datasheet can be accessed through the Texas Instruments listing at https://www.datasheets.com/texas-instruments/opa642p, with additional PDF access through the Alldatasheet result at https://www.alldatasheet.com/datasheet-pdf/pdf/848676/TI1/OPA642P.html. The manufacturer datasheet is the authoritative source for limit values, test conditions, pin definitions, typical characteristics, and application guidance. The supplied search data identifies a 16-page PDF but does not provide a verified TI document number.
Where can I find the OPA642P pinout?
The OPA642P uses an 8-pin PDIP package, and the manufacturer datasheet is the authoritative location for its numbered pinout. The supplied verified results confirm the package type and pin count but do not reproduce individual pin names, so the pinout cannot be transcribed reliably from the provided evidence. Check the pin configuration and package drawing in the original Texas Instruments datasheet before wiring the amplifier or verifying whether a candidate substitute is truly pin compatible.
Where can I buy OPA642P online?
The OPA642P can be found through distributors including DigiKey, Octopart, and authorized sourcing channels that list the original Texas Instruments or Burr-Brown device. Verified search results include https://www.digikey.com/en/products/detail/rochester-electronics-llc/OPA642P/11528067 and https://octopart.com/part/burr-brown/OPA642P. The supplied evidence does not include current numeric prices, so XAIPART treats the part as quote-on-request as of 2026-10-28 rather than presenting an unsupported price.
What is the price of OPA642P as of 2026-10-28?
A verified unit price for OPA642P is not available in the supplied market data as of 2026-10-28. The DigiKey and Octopart listings establish that the part is offered through distribution channels, but the retrieved snippets do not expose usable numeric price breaks. Accordingly, the tier prices are encoded as zero placeholders for quote-on-request presentation and must not be interpreted as a free or guaranteed market price. Obtain a current quotation tied to manufacturer, lot, and date before purchasing.
What is the lead time for OPA642P and is it in stock?
Current OPA642P lead time and stock quantity are not stated in the verified results as of 2026-10-28. The DigiKey result says the part can be purchased and shipped, but that statement alone does not establish present inventory for a specified quantity or package. XAIPART therefore uses BackOrder availability in the product schema and recommends requesting a date-confirmed quote. The distributor listing and seller inventory should be checked for allocation and traceability information.
What can replace OPA642P?
OPA642PB and other verified members of the Texas Instruments OPA64x family are the closest same-brand replacement candidates, but each must be checked against the required gain setting, supply limits, package, and pin configuration. The supplied cross-reference data does not establish five fully verified cross-brand, same-package drop-ins, so it would be misleading to claim that a generic amplifier is automatically interchangeable. Treat OPA642PB as the primary lead for evaluation and validate the complete datasheet before substitution.
Is OPA642P the same as OPA642PB?
OPA642P and OPA642PB are closely related Texas Instruments orderable variants associated with the same OPA642 amplifier family and 8-pin PDIP format, but they should not be treated as automatically identical without checking the orderable drawing and full part specification. The verified comparison search explicitly lists OPA642PB against OPA642P, while the target data identifies OPA642P as 8-PDIP. Verify package dimensions, pin orientation, temperature grade, and ordering suffix before using it as a drop-in replacement.
Is OPA642P suitable for wideband video signal conditioning?
Yes, the OPA642P is suitable for wideband video signal conditioning because the manufacturer data specifies a 400 MHz gain-bandwidth product, low distortion at 5 MHz, and a 95 dB open-loop gain. Its low-gain voltage-feedback architecture is appropriate for preserving high-frequency signal content. The designer must still account for settling time, output loading, PCB parasitics, and closed-loop stability when selecting the external feedback network.
OPA642P versus OPA642UB: which is better for a new design?
OPA642P is the better choice when an existing 8-pin PDIP footprint must be retained, while OPA642UB is the more compact surface-mount option for a new PCB. The verified comparison result identifies OPA642UB as an 8-pin SOIC device and OPA642P as an 8-pin PDIP device, so they are not package-compatible drop-ins. Both belong to the same broad amplifier family, but PCB layout, thermal requirements, and verified electrical limits must be compared before selection.
When should I choose OPA642P over a lower-speed operational amplifier?
Choose OPA642P when the signal path requires its 400 MHz gain-bandwidth product, 0.01% 12-bit settling behavior, or ±60 mA output-drive capability. It is better suited to wideband video, communications, active filtering, and high-speed instrumentation than a general-purpose amplifier such as LM324D. The tradeoff is the older through-hole PDIP package and the additional care required for high-speed bypassing and feedback-layout stability.
What is the best Texas Instruments equivalent for OPA642P?
OPA642PB is the leading same-brand equivalent lead because it appears directly in the supplied OPA642P comparison results and is associated with the same 8-pin PDIP family format. Its availability, exact electrical limits, and orderable package drawing must still be confirmed. Cross-brand parts were not identified with sufficient package-and-pin evidence in the supplied cross-reference data, so a competitor part cannot be responsibly presented as a verified drop-in equivalent.

داتای سەرچاوەی ئەندازیاری بۆ OPA642P — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose OPA642P when an existing 8-pin PDIP design needs a 400 MHz gain-bandwidth product, 2.7 nV/√Hz input-noise density, and 0.01% 12-bit settling. It is particularly appropriate for wideband video, communications, active filtering, instrumentation, converter interfaces, and pulse conditioning. Consider OPA640P when a lower-gain same-family option is sufficient, OPA641P when a nominal +2 configuration is preferred, and OPA643P or OPA644P when a higher gain configuration is more appropriate. OPA642PB is the closest candidate explicitly identified by the supplied comparison data and should be checked for full orderable compatibility. OPA642UB is not a package drop-in because it uses an 8-pin SOIC footprint. Always compare the complete manufacturer datasheet before substituting any device, especially for common-mode range, output swing, noise, settling, slew rate, and stability.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە OPA640P OPA641P OPA642PB OPA643P OPA644P
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP
Product Type Wideband, low-distortion, low-gain voltage-feedback operational amplifier Same-family wideband voltage-feedback operational amplifier Same-family wideband voltage-feedback operational amplifier Wideband, low-distortion operational amplifier Same-family higher-gain voltage-feedback operational amplifier Same-family higher-gain voltage-feedback operational amplifier

جیاکەرەوە سەرەکییەکان

  • High bandwidth for a single low-gain operational amplifier (بەراورد بەLM324D)
  • Low-noise wideband signal conditioning (بەراورد بەOPA643P)
  • Closest identified same-package ordering candidate (بەراورد بەOPA642UB)

تێبینییەکانی دیزاین

Use the shortest possible feedback loop and place input, output, and decoupling connections directly on the associated pins. The verified 400 MHz gain-bandwidth product means that board parasitics cannot be treated as negligible. Provide a continuous ground plane, avoid shared resistive paths between input and output grounds, and place supply bypass capacitors adjacent to the device. Validate the final layout with an oscilloscope because parasitic feedback can reduce phase margin even when the schematic appears correct.

Do not assume that every OPA64x-family amplifier is an exact replacement for the OPA642P. The devices can differ in intended gain configuration, bandwidth, and detailed limit values even when they share an 8-pin PDIP format. OPA642PB is the closest candidate identified by the supplied comparison results, while OPA641P, OPA643P, and OPA644P require gain-configuration review. Before substitution, compare the complete manufacturer datasheets for supply range, input common-mode range, output swing, noise, slew rate, and stability.

Check the closed-loop response rather than relying only on the 400 MHz gain-bandwidth product. Feedback resistance and capacitance, source and load impedance, output capacitance, and target gain all affect bandwidth and stability. Keep the feedback components close to the amplifier, use a single-point ground strategy where appropriate, and avoid long interstage traces that behave as transmission lines at high frequencies. Probe at the device using a short ground spring to reduce misleading ringing in the measured response.

The verified information confirms a ±5.5 V operating condition and ±60 mA output-current capability, but it does not provide the complete current, power, or thermal limits. These values must therefore be obtained from the manufacturer datasheet before sizing supplies and copper paths. Because the amplifier is intended for high-speed operation, supply bypassing should be treated as part of the signal path, with low-inductance capacitors positioned as close as practical to the package.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The supplied verified results identify the manufacturer, device type, package, and core performance data but do not provide RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. These statuses must be verified from the current manufacturer product page or declaration documentation.

داتا پشتڕاستکراوەتەوە لە: 2026-10-28 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

OPA642P OPA642P datasheet Texas Instruments OPA642P OPA642P 400MHz operational amplifier OPA642P 8-pin PDIP OPA642P wideband video amplifier OPA642P communications signal conditioning OPA642P vs OPA642UB OPA642P drop-in replacement OPA642P buy price OPA642P lead time and stock Where to find OPA642P pinout OPA642P 12-bit settling amplifier OPA642P low distortion 5MHz What can replace OPA642P?

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments Burr-Brown OPA642P OPA642PB OPA642UB OPA640P OPA641P OPA643P OPA644P operational amplifier voltage-feedback amplifier analog signal-chain IC semiconductor gain-bandwidth product input noise density common-mode rejection ratio open-loop gain settling time slew rate PDIP-8 through-hole package wideband video communications receiver high-speed instrumentation active filter
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ