OPA698ID - 450 MHz Wideband Amplifier | Texas Instruments
MPN: OPA698ID ✓ چالاکOPA698ID گشتی
An operational amplifier is an active semiconductor component that uses high open-loop gain to amplify the difference between two input voltages. Voltage-feedback amplifiers implement this function with an internal compensation approach suited to high-speed, low-distortion signal chains. In a closed-loop circuit, the feedback network defines the closed-loop gain while negative feedback reduces distortion and improves gain accuracy. The OPA698ID belongs to the broad operational-amplifier and signal-conditioning IC hierarchy.
Unity-gain stability allows the OPA698ID to be used with a feedback factor that produces approximately unity closed-loop gain without causing instability. Its 450 MHz -3 dB bandwidth provides substantial signal-rate capability, while the 1100 V/µs slew rate supports rapid transitions. These characteristics are particularly relevant to waveform conditioning, pulse generation, video-signal paths, test equipment, and systems requiring fast recovery after output clipping.
The defining feature is wideband voltage limiting. In contrast to an ordinary wideband amplifier that may remain in linear operation after its output approaches the supply rails, the OPA698 is intended to recover quickly from limiting conditions. According to the Texas Instruments OPA698 datasheet, the manufacturer recommends the OPA699 when higher-gain or transimpedance operation requires output limiting with fast recovery. This distinction makes device selection based on topology and gain important rather than relying only on bandwidth.
Typical applications include high-speed instrumentation, active filters, wideband buffers, communications interface circuits, video-signal conditioning, and factory test systems. In a practical signal chain, the amplifier can provide gain or buffering between a sensor, converter, or test source and a downstream acquisition or processing stage. Designers should account for input and output headroom, supply range, stability, noise, and the intended closed-loop gain when evaluating the circuit.
The primary layout consideration is to keep feedback-loop paths short and use a ground plane that provides a low-impedance return for high-frequency currents. Decoupling capacitors should be placed directly beside the supply pins, and unused inputs require a defined common-mode voltage. Probe and fixture parasitics can materially affect a circuit with 450 MHz bandwidth, so measurement bandwidth and component selection must match the intended operating conditions.
This product page consolidates the manufacturer-defined bandwidth, slew-rate, gain-bandwidth, output-current, stability, package, and limiting characteristics with application guidance, replacement considerations, and design notes. These engineering details help distinguish the OPA698ID from general-purpose amplifiers and make it possible to assess fit before committing a high-speed board layout.
جێگرەوەکانی جێگۆڕکێ بۆ OPA698ID — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ OPA698ID (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە -3 dB Bandwidth, Gain-Bandwidth Product, Slew Rate.
OPA699ID
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →OPA698ID زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Amplifier Type | Voltage-feedback operational amplifier |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 250 MHz |
| -3 dB Bandwidth | 450 MHz |
| Slew Rate | 1100 V/µs |
| زۆرترین ئێستای دەرچوون | 120 mA |
| Unity-Gain Stability | Yes |
| Primary Function | Wideband voltage limiting |
| Package Type | 8-pin SOIC |
| جۆری دامەزراندن | Surface mount |
ڕێنمایی ڕێکخستنی پینی OPA698ID 8-pin soic
ڕێکخستنی پین بۆ OPA698ID (پاکێجی 8-pin soic). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ OPA698ID.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
OPA698ID گونجاوە بۆ 6 بەکارھێنانs: High-Speed Instrumentation, Video Signal Conditioning, Wideband Active Filters, Communications Interface Circuits, Factory Test Systems, Pulse and Waveform Conditioning.
High-Speed Instrumentation
OPA698ID fits high-speed instrumentation because its 450 MHz -3 dB bandwidth, 250 MHz gain-bandwidth product, and 1100 V/µs slew rate preserve the amplitude and timing of rapidly changing analog signals. It can provide gain or buffering between a source and an acquisition stage while keeping the signal path within the amplifier's specified bandwidth. The 120 mA output-current capability is relevant when driving downstream capacitance or a terminated instrument input. Designers should still verify input and output headroom, supply voltage, noise, and stability against the complete electrical tables before finalizing the signal chain.
پێشنیارکراو
Video Signal Conditioning
OPA698ID is applicable to video-signal conditioning because its 450 MHz -3 dB bandwidth covers high-definition and related wideband video paths, while the 1100 V/µs slew rate supports rapid voltage transitions. Its unity-gain stability permits buffer-style use when source and destination impedances require isolation. The wideband voltage-limiting behavior can help recover rapidly from overload conditions. PCB implementation is critical because long traces, excessive loop area, and poorly decoupled supply connections can degrade the performance expected from a 450 MHz amplifier.
Wideband Active Filters
OPA698ID can serve as the active element in wideband filter and frequency-response circuits because it combines a 250 MHz gain-bandwidth product with a 450 MHz -3 dB bandwidth and unity-gain stability. These characteristics allow a designer to implement signal shaping or buffering at high frequencies without requiring a decompensated amplifier for unity-gain operation. Component tolerances and parasitic capacitance become increasingly important as the operating frequency approaches the amplifier's bandwidth. Validate gain, phase margin, noise, and allowable output swing using the manufacturer's stability and electrical-characteristic guidance.
Communications Interface Circuits
OPA698ID is suitable for communications interface stages requiring broad bandwidth and accurate large-signal behavior. Its 450 MHz -3 dB bandwidth can accommodate high-rate analog signaling, while the 1100 V/µs slew rate and 120 mA output current provide margin for fast edges and moderate capacitive loading. The device's wideband voltage limiting is particularly useful when an upstream signal may exceed the intended output range and rapid recovery is required. Keep routing compact, maintain a continuous ground reference, and confirm that the communications system's common-mode and output-swing requirements remain within the operating limits.
Factory Test Systems
OPA698ID can support factory test and measurement systems that generate or condition waveforms requiring fast transitions and substantial bandwidth. The 450 MHz -3 dB bandwidth supports high-frequency test signals, while the 1100 V/µs slew rate limits large-signal timing distortion and the 120 mA output current helps drive moderate test loads. Unity-gain stability makes it useful when a probe, cable, or acquisition input benefits from a low-impedance buffer. Account for fixture capacitance, cable loss, and probe loading because these parasitics can dominate a practical test fixture.
Pulse and Waveform Conditioning
OPA698ID fits pulse and waveform-conditioning tasks where fast output transitions and recovery from limiting are important. Its 1100 V/µs slew rate supports rapid waveform edges, while unity-gain stability enables direct buffering configurations and the 450 MHz -3 dB bandwidth preserves higher-frequency content. Wideband voltage limiting provides a defined behavior when an input excursion drives the output toward the allowed operating region. Check the output swing and recovery requirements, maintain adequate supply and output headroom, and use short feedback paths to avoid unintended ringing at high edge rates.
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ OPA698ID — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | OPA699ID |
|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC |
| Brand | Texas Instruments | Texas Instruments |
| Amplifier Type | Voltage-feedback operational amplifier | Wideband voltage-feedback operational amplifier |
| Number of Circuits | 1 circuit | 1 circuit |
| Primary Positioning | Wideband voltage limiting | Higher-gain or transimpedance application with output limiting and fast recovery |
جیاکەرەوە سەرەکییەکان
- Purpose-built wideband voltage limiting (بەراورد بەOPA699ID)
- Direct unity-gain buffering capability (بەراورد بەOPA699ID)
- High large-signal transition capability (بەراورد بەOPA699ID)
تێبینییەکانی دیزاین
Keep the OPA698ID feedback loop physically small and connect the amplifier ground directly to the ground plane. A circuit with 450 MHz bandwidth can pick up trace inductance and distributed capacitance that are negligible at low frequencies. Route the output toward the load only after the feedback connection is complete, and avoid sharing narrow return paths with switching or high-current circuits.
Place the manufacturer's recommended bypass capacitors immediately across the supply pins, with the ground ends connected to a low-impedance plane. Keep the input and output common-mode voltages within their permitted ranges and preserve the required headroom to the supply rails. A wideband amplifier cannot operate linearly outside those limits even when its bandwidth and slew-rate ratings appear suitable for the signal.
Treat probe, cable, fixture, and component parasitics as part of the amplifier design at 450 MHz. Select resistor and capacitor values that preserve the intended feedback network, and measure with bandwidth that does not obscure the behavior being evaluated. Fast 1100 V/µs slew-rate capability can reveal ringing or stability problems that are hidden by a slower test setup.
Do not assume that unity-gain stability guarantees identical behavior at every feedback value or load. Confirm the intended noise gain, output loading, supply configuration, and common-mode range using the manufacturer datasheet. Also distinguish ordinary linear operation from wideband voltage limiting: OPA698ID is specifically positioned for limiting behavior with fast recovery, so confirm that this characteristic is beneficial to the end circuit.
زانیاری پابەندبوون
Compliance status was not stated in the manufacturer excerpts or other available component pages.