PCA9534DB - 8-Bit I2C I/O Expander | Texas Instruments
MPN: PCA9534DB ✓ چالاکPCA9534DB گشتی
An I2C I/O expander is a peripheral that converts a serial I2C or SMBus connection into additional parallel digital input and output lines. In the product hierarchy, it is a general-purpose I/O expander, an interface IC, and ultimately a semiconductor. The PCA9534DB is useful when a controller has too few GPIO pins for buttons, indicators, relays, logic inputs, or other digital peripherals. Its three hardware address pins permit up to eight devices to share one bus.
The principal features include eight independently configurable I/O ports, a 2.3 V to 5.5 V operating range, 400 kHz I2C operation, programmable configuration registers, and an active-low interrupt output. The TI product page also states that the device is pin-to-pin and I2C-address compatible with the PCF8574, although software changes are required because the PCA9534 adds enhanced register behavior. This makes it possible to retain familiar hardware while adopting more flexible configuration and interrupt handling.
Internally, the device combines a serial interface with an 8-bit port register and a configuration register that establishes input or output operation for each port bit. The VCC range supports both 3 V and 5 V powered systems, while the 400 kHz bus rating provides compatibility with common embedded-control interfaces. The provided operating-temperature information identifies a -40 C to +85 C range, and the package information identifies a 16-pin SSOP compatible with MS-013 and SOT162-1 outlines.
Typical applications include industrial control panels, sensor and relay interfaces, programmable logic controllers, communications equipment, portable instrumentation, and embedded systems requiring more GPIO than the host controller provides. In each case, the PCA9534DB can connect a microcontroller to discrete digital inputs and outputs while reducing the number of direct host pins required. The interrupt line can also support event-driven designs in which the controller processes input changes only after notification.
When laying out a design, place the device close to the connector or controlled peripheral and keep SDA and SCL routing short. The verified material does not specify required external pull-up values, so those must be selected from the host-bus voltage, capacitance, and bus-speed requirements. Software should also account for the PCF8574 compatibility qualification: the hardware interface is compatible, but the PCA9534 enhancements require firmware changes.
This product data combines the verified manufacturer and distributor references with a practical comparison against PCF8574- and PCA9554-family devices. It distinguishes true package and pin compatibility from broader functional similarity, identifies unresolved pricing and electrical details, and highlights the design checks needed before replacing an existing I/O-expander implementation.
جێگرەوەکانی جێگۆڕکێ بۆ PCA9534DB — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ PCA9534DB (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Configuration Registers.
PCA9554DB
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →PCF8574DB
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
PCA9534DB تایبەتمەندییەکان
| Number of I/O Ports | 8 ports |
| جۆری ڕووکار | I2C and SMBus |
| ڤۆڵتاژی دابینکردنی کارکردن | 2.3 V to 5.5 V |
| Maximum I2C Bus Frequency | 400 kHz |
| Number of Address Pins | 3 pins |
| Maximum Devices on One Bus | 8 devices |
| Output Port Configuration | 8 configurable I/O bits |
| Interrupt Function | 1 interrupt output |
| Configuration Registers | Available |
| Technology | CMOS |
| Device Type | General-purpose I/O expander |
| پلەی گەرمیی کارکردن | -40 C to +85 C |
| Package Type | 16-pin SSOP |
| Package Outline | MS-013, SOT162-1 |
| Package Body Width | 7.50 mm |
| ژمارەی پین | 16 pins |
| Surface-Mount Package | Yes |
| Power Input | 1 VCC pin |
| Ground Input | 1 GND pin |
| Internal I/O Pull-Up Resistors | Removed relative to PCA9554 |
| PCF8574 Compatibility | Pin-to-pin and I2C-address compatible; software changes required |
ڕێکخستنی پینی PCA9534DB
| پین 1 | A0 — I2C address input |
| پین 2 | A1 — I2C address input |
| پین 3 | A2 — I2C address input |
| پین 4 | P0 — General-purpose input/output port 0 |
| پین 5 | P1 — General-purpose input/output port 1 |
| پین 6 | P2 — General-purpose input/output port 2 |
| پین 7 | P3 — General-purpose input/output port 3 |
| پین 8 | GND — Ground |
| پین 9 | P4 — General-purpose input/output port 4 |
| پین 10 | P5 — General-purpose input/output port 5 |
| پین 11 | P6 — General-purpose input/output port 6 |
| پین 12 | P7 — General-purpose input/output port 7 |
| پین 13 | SCL — Serial clock input |
| پین 14 | SDA — Bidirectional serial data input and output |
| پین 15 | INT — Interrupt output |
| پین 16 | VCC — Power supply |
بەکارهێنانە باوەکان
PCA9534DB گونجاوە بۆ 6 بەکارھێنانs: Industrial Control Panel I/O, Relay and Solenoid Control, Sensor and Alarm Input Aggregation, PLC and Programmable Control Interface, Communications Equipment Status Interface, Portable Instrumentation and Control.
Industrial Control Panel I/O
The PCA9534DB fits industrial control panels where a controller must operate multiple pushbuttons, status lamps, selectors, or discrete input modules. Its eight configurable ports expand the host's I2C interface into parallel digital lines while operating from the same 2.3 V to 5.5 V range used by many embedded controllers. The 400 kHz I2C rate is sufficient for routine panel updates, and the interrupt output lets the controller respond to input changes without continuously polling all eight ports. Designers should place the expander near the panel wiring, protect external connections according to the target industrial environment, and confirm that connected loads remain within the datasheet limits.
پێشنیارکراو
Relay and Solenoid Control
The PCA9534DB is useful for low-current relay, solenoid, and indicator drive boards that are separated from a microcontroller by a cable. Eight outputs can control discrete channels through suitable driver circuitry, while the 2.3 V to 5.5 V logic range allows integration with either 3 V or 5 V control systems. The interrupt output supports designs that must report switch, sensor, or fault events back to the host. Because the I/O ports are not universal power-stage drivers, relay coils and solenoids require appropriate transistor or MOSFET drive circuits, flyback protection, and voltage ratings that exceed the load requirements.
پێشنیارکراو
Sensor and Alarm Input Aggregation
The PCA9534DB can consolidate eight discrete digital sensor or alarm signals into a compact controller interface. Inputs can be read through the I2C port register, while the interrupt line provides an event-driven path for door, tamper, limit, or presence indications. The 400 kHz bus capability permits shared access with other addressable peripherals, and the three address inputs allow multiple PCA9534 devices to coexist on one bus. In alarm systems, design the logic levels and thresholds to match the sensors, account for the device's documented input and output characteristics, and avoid relying on unverified assumptions about internal pull-ups because this family omits them.
پێشنیارکراو
PLC and Programmable Control Interface
The PCA9534DB provides a practical remote I/O expansion path for PLC-like and programmable-control systems with a limited pin count. A central controller communicates over I2C or SMBus at up to 400 kHz and reads or updates eight local digital points through the expander. The 2.3 V to 5.5 V operating range supports both legacy 5 V logic and lower-voltage modern control platforms, while three address pins permit several distributed I/O blocks on one bus. For dependable operation, isolate noisy industrial wiring from the serial bus, use appropriate connectors and surge protection, and verify timing, input levels, and output-current limits against the manufacturer datasheet.
پێشنیارکراو
Communications Equipment Status Interface
The PCA9534DB is suitable for communications equipment that needs scattered link-status, fan, alarm, or configuration signals without consuming many controller pins. The eight ports operate over a compact two-wire bus, and the interrupt output supports prompt handling of asynchronous events without continuous register polling. Its 400 kHz I2C speed matches common embedded processor peripherals, while the 16-SSOP package supports compact board layouts. In a router, interface card, or communications module, the interrupt line should be routed away from high-edge-rate signals, and the power and ground connections should follow the decoupling and return-current guidance in the manufacturer datasheet.
پێشنیارکراو
Portable Instrumentation and Control
The PCA9534DB can expand a portable instrument with switches, mode controls, indicators, and data-ready signals while keeping the host-controller footprint compact. Its 2.3 V minimum operating voltage supports low-voltage portable systems, and the 400 kHz bus rate allows efficient register-based updates. The interrupt output is valuable in handheld or battery-powered equipment because it allows the controller to remain idle until an external event occurs. Engineering teams should evaluate total board power, connector grounding, and ESD protection, then confirm that all connected logic levels satisfy the PCA9534DB electrical characteristics before releasing the layout.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ PCA9534DB — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | PCA9554DB | PCF8574DB |
|---|---|---|---|
| Package | 16-SSOP | 16-SSOP | 16-SSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| I/O Port Count | 8 bits | 8 bits | 8 bits |
| Interface | I2C/SMBus | I2C | I2C |
| Configuration Registers | Yes | Yes | No enhanced configuration behavior; software changes required for PCA9534 |
جیاکەرەوە سەرەکییەکان
- Lower power behavior than the PCA9554 when I/O lines are held LOW (بەراورد بەPCA9554DB)
- Enhanced configuration behavior while retaining PCF8574 hardware compatibility (بەراورد بەPCF8574DB)
- Eight distributed digital lines on a compact two-wire interface (بەراورد بەPCF8574DB)
تێبینییەکانی دیزاین
Route SDA and SCL as short, continuous traces between the host controller and PCA9534DB, while keeping the I/O port traces away from high-current switching paths. Place the device near the connector or peripheral group it serves to reduce trace length and improve signal integrity. The verified package is a 16-pin SSOP, so provide unobstructed soldering and inspection clearance around the leads. Exact placement, trace widths, and via counts should follow the PCB-stackup guidance in the manufacturer datasheet.
Supply the PCA9534DB from a rail within its verified 2.3 V to 5.5 V operating range and provide local bypass capacitance close to VCC and GND. Keep the ground return connected to the same reference plane as the associated controller and decouple the I/O branch near the device. External I/O traces should use protection appropriate to the installation, including clamp devices for exposed connectors where transient limits are not otherwise guaranteed.
Do not treat the PCA9534DB's PCF8574 compatibility as a firmware-compatible relationship. The Texas Instruments product page states that the hardware is pin-to-pin and I2C-address compatible, but software changes are required because the PCA9534 adds enhanced register behavior. Also note that the PCA9534 omits the internal I/O pull-up resistors present on the PCA9554, so external pull-ups may be required. Review both register mapping and the complete bus pull-up network before substitution.
Use the interrupt line as an event-driven notification and still read the port and configuration registers to identify which input changed. Keep the interrupt trace short and isolated from noisy relay-coil or motor-switching nodes. For multiple PCA9534 devices, assign A0, A1, and A2 to unique values so that as many as eight devices can share the bus. The verified I2C rate is 400 kHz; actual bus operation must also satisfy the timing and loading limits specified in the manufacturer datasheet.
زانیاری پابەندبوون
The verified manufacturer and distributor excerpts do not provide material-compliance declarations for the exact PCA9534DB orderable MPN. Compliance fields remain unknown pending a current manufacturer declaration.