PIC16F1789-I/P - 8-Bit 32MHz 28KB Flash Advanced Analog MCU | Microchip
MPN: PIC16F1789-I/P ✓ چالاکPIC16F1789-I/P گشتی
A microcontroller (MCU) is a single integrated circuit that combines a CPU core, program memory, data memory and peripherals such as analog converters, timers and communication ports on one die. The PIC16F1789 belongs to the enhanced mid-range PIC16 family, whose 49-instruction RISC core executes most instructions in 200 ns at 32 MHz and provides 16 levels of hardware stack. Within the wider hierarchy, this device is an 8-bit MCU -> embedded controller -> analog-enhanced embedded processor.
Key features include a 15-channel 12-bit ADC, an 8-bit DAC and a 5-bit DAC, four Peripheral Stimulus Generator (PSMC) channels for complex waveform generation, and an internal 32 MHz oscillator that eliminates external clock components. Self-read/write Flash program memory and 256 bytes of data EEPROM support field-updatable firmware and parameter storage, while the XLP designation reflects the low-power design goals of the family.
The 28-pin PDIP footprint exposes the full port complement plus dedicated analog pins. Because the analog channels are multiplexed onto the same port pins used for digital I/O, a firmware configuration step decides whether each pin behaves as a digital input or output or as an analog function, and the datasheet's analog-configuration table governs that decision.
Typical uses include industrial sensor acquisition and control, compact power conversion and LED lighting subsystems, motor and actuator control with PSMC-driven drive, battery-powered monitoring nodes, and mixed-signal instrumentation where a 12-bit ADC and DAC pair replace separate converter chips.
One key design consideration is decoupling: place a 100 nF ceramic bypass capacitor physically at each VDD/VSS pair and a bulk capacitor near the analog reference node, and keep analog input traces short and routed away from the switched-capacitor outputs of the AD module. Check the ADC acquisition time requirement before choosing the sampling rate.
This page consolidates parametric detail, drop-in replacement options, application guidance and practical layout notes so engineers can qualify the PIC16F1789-I/P for a new design without assembling the same information from multiple sources.
جێگرەوەکانی جێگۆڕکێ بۆ PIC16F1789-I/P — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ PIC16F1789-I/P (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, ADC, Comparators, DAC, Program Memory (Flash).
PIC16F1788-I/P
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
PIC16F18313-I/P
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →PIC16F1823-I/P
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →PIC16F15375-I/PT
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →PIC16F1789-I/PT
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
PIC16F76-I/SP
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →PIC16F1789-I/P زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Product Type | 8-Bit Flash Microcontroller (MCU) |
| Architecture | Enhanced mid-range PIC16 RISC core, 49 instructions |
| زۆرترین فرێکوێنسیی کاتژمێر | 32 MHz |
| Program Memory (Flash) | 28 KB (16K x 14 words) |
| Program Memory Type | Flash, with self read/write capability |
| Data Memory (SRAM) | 2048 bytes |
| Data EEPROM | 256 bytes |
| ADC | 12-bit, 15 channels |
| DAC | 8-bit DAC and 5-bit DAC |
| PSMC Channels | 4 |
| Internal Oscillator | 32 MHz internal oscillator |
| Hardware Stack | 16 levels |
| Instruction Execution Time | 200 ns |
| پاکێج | 28-pin PDIP, through-hole |
| مەودای پلەی گەرمیی کارکردن | -40 C to +85 C (industrial, -I grade) |
| Process Technology | CMOS |
| Programmable Peripheral Stimulus Generator | Yes, 4 channels with independent edge generators |
| Programmable Voltage Detector (PVD) | Yes |
| Brown-Out Reset (BOR) | Yes |
| Watchdog Timer | Yes, WDT with software control |
| I2C | Yes, with 2-bit address masking |
| SPI | Yes |
| UART | Yes, with auto-baud detection |
| Status | In Production |
ڕێنمایی ڕێکخستنی پینی PIC16F1789-I/P 28-pin pdip, through-hole
ڕێکخستنی پین بۆ PIC16F1789-I/P (پاکێجی 28-pin pdip, through-hole). ئەم IC ی دیجیتاڵە GPIO، ڕووکارەکانی پەیوەندی (UART، SPI، I2C) و پینی وزە لەخۆدەگرێت. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ فەنکشنەکانی پینی جێگرەوە و ھەڵبژاردنەکانی ڕێکخستن. پێویستە بۆ دیزاینی سیستەمی جێگیر و ڕێکخستنی PCB.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ PIC16F1789-I/P.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
PIC16F1789-I/P گونجاوە بۆ 6 بەکارھێنانs: Industrial Sensor Acquisition and Data Logging, LED Lighting Control and Dimming, Battery-Powered Monitoring Node, Motor and Actuator Control, Mixed-Signal Instrumentation and Test Equipment, Smart Building and HVAC Control.
Industrial Sensor Acquisition and Data Logging
The PIC16F1789-I/P fits multi-channel process monitoring because its 12-bit ADC covers 15 analog inputs in a single device, removing the need for external analog mux or converter parts. At a 32 MHz core clock with 200 ns instruction execution, the CPU has ample headroom to sample, filter and timestamp channels while running the UART or I2C link to a supervisory station. The 2048 bytes of SRAM and 256 bytes of data EEPROM hold calibration coefficients and configuration records, and self-read/write Flash lets field engineers update firmware without removing the part. The -I grade covers -40 C to +85 C, matching typical plant-room conditions.
پێشنیارکراو
LED Lighting Control and Dimming
Driving LED arrays is a natural fit for the four Peripheral Stimulus Generator channels of the PIC16F1789-I/P, which generate precise, independent edges and pulse shapes without heavy timer chaining. The internal 32 MHz oscillator keeps the timing reference consistent, while the 5-bit DAC and 8-bit DAC outputs can provide reference levels or analog control signals to external driver circuits. Self-read/write Flash is useful for storing lighting scenes and fade curves, and the low-power XLP design targets efficient always-on lighting controllers where standby consumption matters.
پێشنیارکراو
Battery-Powered Monitoring Node
The PIC16F1789-I/P belongs to the PIC16 XLP family, making it appropriate for remote, battery-fed sensor nodes that must idle at low current and wake periodically to report. The 256-byte EEPROM preserves counters and identifiers across resets without consuming Flash endurance, and the 15-channel 12-bit ADC lets a single node supervise several slow-moving analog inputs. The internal 32 MHz oscillator eliminates the crystal and its associated load current, while the UART with auto-baud detection simplifies attachment to cellular or LoRa radio modules over a short UART link.
پێشنیارکراو
Motor and Actuator Control
The four PSMC channels of the PIC16F1789-I/P allow precise, hardware-timed step or pulse output for driving small motors, solenoids or valves, with edge timing that is far more stable than software toggling a general-purpose pin. The 32 MHz core runs the closed-loop control maths and housekeeping logic while the PSMC handles timing-critical pulse generation independently. A 5-bit DAC can bias sensor front ends or generate an analog setpoint, and the abundant 12-bit ADC channels suit current and position sensing in compact actuator modules.
پێشنیارکراو
Mixed-Signal Instrumentation and Test Equipment
Instrument front ends benefit from having a 12-bit ADC and two DACs alongside a control core in one package, because the analog conversion path stays short and the digital section can run calibration loops at 32 MHz. The 8-bit DAC supports stimulus generation and offset injection, while the 5-bit DAC works with comparators for threshold and window detection. Self-read/write Flash allows stored calibration tables to be updated in the field, and the 28-pin PDIP package makes the design straightforward to prototype and rework on a through-hole bench board.
پێشنیارکراو
Smart Building and HVAC Control
Building controllers typically read many analog inputs and drive a mix of digital outputs, which maps directly onto the 15-channel 12-bit ADC and the general-purpose I/O of the PIC16F1789-I/P. The I2C peripheral with address masking can host multiple temperature and humidity sensors on one bus, while the UART supports a supervisory panel or gateway link. Store occupancy schedules and setpoints in the data EEPROM, update control firmware through self-read/write Flash, and rely on the -40 C to +85 C rating for equipment rooms and perimeter-mounted panels.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ PIC16F1789-I/P — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | PIC16F1788-I/P | PIC16F18313-I/P | PIC16F1823-I/P | PIC16F15375-I/P | PIC16F1789-I/PT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-pin PDIP | 28-pin PDIP - same | 28-pin PDIP - same | 28-pin PDIP - same | 28-pin PDIP - same | 28-pin surface-mount variant - not a through-hole drop-in |
| Maximum Clock Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Program Memory (Flash) | 28 KB (16K x 14 words) | 28 KB (16K x 14 words) | 14 KB | 3.5 KB | 16 KB | 28 KB (16K x 14 words) |
| Data Memory (SRAM) | 2048 bytes | 2048 bytes | 1536 bytes | 128 bytes | 1024 bytes | 2048 bytes |
| Data EEPROM | 256 bytes | 256 bytes | 256 bytes | 256 bytes | 256 bytes | 256 bytes |
| ADC | 12-bit, 15 channels | 12-bit, fewer channels | 12-bit, fewer channels | 10-bit, fewer channels | 12-bit, fewer channels | 12-bit, 15 channels |
| DAC | 8-bit DAC and 5-bit DAC | Not available | Not available | Not available | 5-bit DAC only | 8-bit DAC and 5-bit DAC |
| PSMC Channels | 4 | 4 | 4 | 2 | 4 | 4 |
| Operating Temperature Range | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
جیاکەرەوە سەرەکییەکان
- Highest analog integration in the 28-pin PIC16 mid-range family (بەراورد بەPIC16F1788-I/P)
- Twice the Flash and 33% more SRAM than the closest modern same-footprint option (بەراورد بەPIC16F18313-I/P)
- Full 12-bit conversion resolution versus a legacy 8-bit-class part (بەراورد بەPIC16F76-I/SP)
- Four hardware PSMC channels for edge and waveform timing (بەراورد بەPIC16F1823-I/P)
تێبینییەکانی دیزاین
Place a 100 nF ceramic bypass capacitor at each VDD/VSS supply pair directly adjacent to the pins, and add a bulk capacitor near the device to handle switching transients. Because analog inputs are multiplexed onto the same port pins used for digital I/O, route analog traces away from digital nets and keep the analog ground reference point close to the analog supply return. Decoupling placement and analog isolation usually matter more to achievable ADC accuracy than the nominal 12-bit resolution.
Configure the analog pins through the ANSEL and ANSELH registers and verify each pin's function against the pin-description table in the manufacturer datasheet before committing copper. A pin left in analog mode cannot be used as a digital input or output, which is a common source of firmware-driven board failures. Also check the ADC acquisition time requirement for the selected source impedance and add an external sample-and-hold capacitor when driving the input from a high-impedance source.
The 28-pin PDIP package offers generous pin spacing for prototyping but no exposed thermal pad, so heat dissipation relies on the through-hole leads and board copper. Keep the device away from linear regulators and power inductors on the PCB, and route high-current switching returns away from the analog reference node. For battery designs, take advantage of the XLP low-power modes and the internal 32 MHz oscillator to avoid the supply current of an external crystal.
Do not confuse the -I/P ordering code with -I/PT: the first is a through-hole PDIP package and the second is a surface-mount part, and mixing them invalidates the footprint. Also note that the PIC16F1788 variant lacks the DAC outputs even though the pinout matches, so a board designed with a DAC reference signal cannot be populated with the 1788 without signal-path changes. Finally, use the internal oscillator only where frequency tolerance requirements allow it; comms designs typically need an external crystal.
زانیاری پابەندبوون
The manufacturer product page lists PIC16F1789 as in production and identifies the part as a PIC PIC XLP 8-bit flash MCU in a 28-pin PDIP package. RoHS, REACH, halogen-free and conflict-minerals status were not stated in the available product information and must be confirmed from the current manufacturer declaration before use in regulated designs.