PIC16F1823-I/P - 8-Bit 32MHz MCU, 3.5KB Flash | Microchip
MPN: PIC16F1823-I/P ✓ چالاکPIC16F1823-I/P گشتی
A PIC16F1823 is a microcontroller, an integrated circuit containing a processor core, program memory, data memory, and peripherals on one semiconductor die. PIC microcontrollers belong to the embedded-controller hierarchy rather than the host-computer category. This enhanced mid-range model combines a RISC-like PIC architecture with XLP-oriented design goals and flash memory, allowing firmware to be programmed and updated in-circuit without a separate external program-memory device.
The principal device characteristics are a maximum 32 MHz operating frequency, 3.5 KB of Flash program memory, 128 bytes of RAM, 12 I/O pins, and a 14-pin PDIP package. The -I operating-temperature designation identifies the industrial-temperature grade, while the /P suffix identifies the PDIP package. The 200 ns instruction execution rate associated with this enhanced mid-range family supports deterministic control loops and responsive peripheral servicing.
The PIC16F1823 architecture is designed around a compact instruction set and integrated peripheral resources. On-chip Flash permits field reprogramming through the device's supported programming interfaces, while the internal oscillator reduces the number of external timing components required. The 128-byte SRAM provides working memory for control variables, yet designers should budget stack depth and RAM carefully when selecting tasks, buffering samples, or maintaining communication frames.
Typical uses include compact environmental controllers, building and industrial automation modules, digital sensing instruments, appliance controls, and low-cost USB-to-serial interface circuits using an appropriate transceiver. A 14-pin PDIP package also simplifies breadboard prototypes and through-hole production builds. The 12 available I/O pins support digital inputs and outputs, while the internal oscillator and flash memory reduce component count in space-constrained designs.
For new layouts, verify the complete 14-pin assignment, supply voltage limits, peripheral multiplexing, and programming connections against the manufacturer data sheet. Do not allocate every I/O pin to a general-purpose function without checking the multiplexed peripheral assignments. Preserve access to MCLR and the programming interface so the finished board can be programmed, tested, and serviced without redesign.
This page combines manufacturer specifications, package and programming guidance, application-specific engineering notes, and verified same-family drop-in candidates. The accompanying comparison table highlights where temperature grade, flash capacity, RAM, oscillator behavior, and supply range affect substitution decisions, helping engineers select a candidate without overlooking firmware, peripheral, or qualification differences.
جێگرەوەکانی جێگۆڕکێ بۆ PIC16F1823-I/P — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ PIC16F1823-I/P (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Internal Oscillator, ADC, I/O Pins, Timers.
PIC16F1823-I/SP
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
PIC16F1823-E/P
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →PIC16F1822-I/P
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
PIC16LF1823-I/P
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →PIC16F1823-I/P
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →PIC16F1823-I/P زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Product Type | 8-bit flash microcontroller |
| Device Family | PIC XLP |
| Architecture | Enhanced mid-range PIC RISC |
| Maximum CPU Frequency | 32 MHz |
| Instruction Execution Time | 200 ns |
| Program Flash Memory | 3.5 KB |
| Program Memory Organization | 2K × 14 words |
| Data RAM | 128 bytes |
| I/O Pin Count | 12 pins |
| پاکێج | 14-pin PDIP |
| جۆری دامەزراندن | Through-hole |
| Internal Oscillator | 32 MHz |
| Temperature Grade | Industrial |
| Programming Support | High-voltage ICSP and low-voltage ICSP |
ڕێنمایی ڕێکخستنی پینی PIC16F1823-I/P 14-pin pdip
ڕێکخستنی پین بۆ PIC16F1823-I/P (پاکێجی 14-pin pdip). ئەم IC ی دیجیتاڵە GPIO، ڕووکارەکانی پەیوەندی (UART، SPI، I2C) و پینی وزە لەخۆدەگرێت. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ فەنکشنەکانی پینی جێگرەوە و ھەڵبژاردنەکانی ڕێکخستن. پێویستە بۆ دیزاینی سیستەمی جێگیر و ڕێکخستنی PCB.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ PIC16F1823-I/P.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
PIC16F1823-I/P گونجاوە بۆ 6 بەکارھێنانs: Compact Environmental Monitoring Controller, Digital Thermostat and Appliance Control, Low-Cost USB-to-Serial Interface, Industrial Counter and Data Logger, Automated Test Fixture Controller, Smart Sensor and IoT Node.
Compact Environmental Monitoring Controller
The PIC16F1823-I/P fits compact environmental monitoring because it combines 12 I/O pins, 3.5 KB of Flash, and 128 bytes of RAM in a 14-pin PDIP package. Its 32 MHz internal oscillator eliminates the need for a separate crystal when the application's timing accuracy permits. Use the I/O pins for digital sensors, alarm outputs, status indicators, and a serial interface, while budgeting the 128-byte RAM carefully for sample buffers and protocol state. The industrial-temperature grade supports industrial ambient conditions, but the complete operating range must still be checked against the enclosure temperature, supply limits, and sensor accuracy requirements.
پێشنیارکراو
Digital Thermostat and Appliance Control
A PIC16F1823-I/P can implement the real-time control logic for a digital thermostat or appliance controller while keeping the through-hole package easy to assemble and service. The 32 MHz CPU provides a 200 ns instruction execution interval, allowing the firmware to sample sensors, update a display, evaluate hysteresis, and switch a relay efficiently. Twelve I/O pins provide connections for a temperature sensor interface, buttons, display control, and actuator drive. Firmware should include debouncing, fail-safe temperature limits, and output-state initialization so the appliance enters a defined condition after reset or power loss.
پێشنیارکراو
Low-Cost USB-to-Serial Interface
The PIC16F1823-I/P is suitable for a basic USB-to-serial interface when a board-level USB transceiver provides the physical data path. Its 32 MHz processing speed and 3.5 KB of program Flash are adequate for command processing, character buffering, and simple line or packet protocols. The 12 I/O pins can support serial data, control lines, and status indicators, although USB timing and bus signal integrity must be handled primarily by the transceiver and board layout. Configure the external oscillator only if the interface's clocking requirements cannot use the internal oscillator, and validate timing margins with an oscilloscope.
پێشنیارکراو
Industrial Counter and Data Logger
The PIC16F1823-I/P can serve as the controller for a small industrial counter or data logger when the required measurement rate and storage volume remain modest. Its 12 I/O pins support switch inputs, alarm outputs, and an external memory or communications interface, while 3.5 KB of Flash holds the application firmware. At 32 MHz, the device can service multiple timers and implement debouncing or pulse accumulation, but designers should calculate worst-case interrupt latency. The 128-byte RAM limits simultaneous buffering, so use a streaming architecture or add external storage rather than retaining large historical records internally.
پێشنیارکراو
Automated Test Fixture Controller
The PIC16F1823-I/P is appropriate for a small automated test fixture that sequences relays or instruments and records pass/fail results. Fast instruction execution supports responsive sequencing, while the 14-pin PDIP package keeps prototype wiring simple and the 12 I/O pins permit several fixture signals to be controlled. Implement watchdog and timeout behavior so a failed sensor or open load cannot stall a production cycle. Because fixture systems often combine noisy relays, switching supplies, and sensitive measurement nodes, keep high-current paths away from the controller ground and use suitable isolation or filtering at interface boundaries.
پێشنیارکراو
Smart Sensor and IoT Node
The PIC16F1823-I/P can form the control core of a compact smart sensor or IoT node that gathers digital measurements and reports status through a serial link. Its 32 MHz internal clock and 128 bytes of RAM are well matched to simple sensor nodes with bounded data rates, and Flash permits firmware revisions without replacing the device. Twelve I/O pins leave room for a sensor, status LED, configuration input, and communications interface. Power-conscious designs should disable unused peripherals and use the controller's low-power modes where compatible with measurement timing, while accounting for the energy contribution of the communications subsystem.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ PIC16F1823-I/P — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | PIC16F1823-I/SP | PIC16F1823-E/P | PIC16F1822-I/P | PIC16LF1823-I/P | PIC16F1823-I/P |
|---|---|---|---|---|---|---|
| Package | 14-pin PDIP | 14-pin SOIC; not the same PCB land pattern | 14-pin PDIP | 14-pin PDIP | 14-pin PDIP | 14-pin PDIP |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Temperature Grade | Industrial | Industrial | Extended commercial | Industrial | Industrial | Industrial |
| Programming Interface | High-voltage ICSP and low-voltage ICSP | High-voltage ICSP and low-voltage ICSP | High-voltage ICSP and low-voltage ICSP | High-voltage ICSP and low-voltage ICSP | High-voltage ICSP and low-voltage ICSP | High-voltage ICSP and low-voltage ICSP |
جیاکەرەوە سەرەکییەکان
- Exact-match configuration for 14-pin through-hole industrial designs (بەراورد بەPIC16F1823-I/SP)
- Broader ambient-temperature suitability than the E-grade candidate (بەراورد بەPIC16F1823-E/P)
- Specific 3.5 KB Flash and 128-byte RAM resource profile (بەراورد بەPIC16F1822-I/P)
- Full 32 MHz speed and 200 ns instruction interval (بەراورد بەPIC16F1822-I/P)
تێبینییەکانی دیزاین
Route the decoupling capacitor from each required power pin to the nearest available ground reference with the shortest practical loop. Keep the programmer-accessible MCLR and ICSP signals available and test them on the assembled PCB. Because this is a 14-pin PDIP device, allocate lead spacing around the IC for inspection and rework, and avoid placing tall components where they interfere with a programming clip.
Validate the operating supply against the device's electrical-characteristics table and leave margin for startup, transient, and brownout behavior. Do not assume that the 32 MHz internal oscillator can be used without reviewing the allowed supply-voltage range and configuration-word settings. Use separate filtering paths for noisy loads, and keep the MCU supply return connected near the device rather than routing return current through long shared traces.
The 12 I/O pins can have alternate peripheral functions, so a pin that appears available in a simplified block diagram may not remain on a general-purpose GPIO after configuration. Build the pin-assignment table from the manufacturer pin description and firmware configuration. Also check that the 128-byte RAM includes enough space for the stack, variables, serial buffers, and interrupt context required by the application.
Keep oscillator, programming, and serial-interface traces away from high-current switching nodes and relay-coil wiring. If an external crystal or resonator is used, follow the manufacturer's recommended grounding and load-capacitor arrangement. For interfaces that connect to cables, provide the required protection network and define a stable common reference; the microcontroller's 12 I/O pins should not be treated as general-purpose surge protection devices.
زانیاری پابەندبوون
The manufacturer product and data-sheet sources do not provide an explicit compliance summary in the retrieved material. Do not infer RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status from the product family or package designation.