PIC16F721-E/SO - 16MHz 8-Bit MCU with ADC | Microchip
MPN: PIC16F721-E/SO ✓ چالاکPIC16F721-E/SO گشتی
A PIC16 microcontroller is a compact embedded-control IC that combines a processor core, program memory, data memory, peripherals, and general-purpose input/output pins on one package. The PIC16 architecture belongs to the broader 8-bit microcontroller hierarchy and is commonly used for cost-sensitive industrial control, instrumentation, appliance control, and simple automation where deterministic peripheral operation and in-circuit programming are valuable.
Key device features include a mid-range core with a 35-instruction set, 8 stack levels, self-read/write flash program memory, and 128 bytes of non-volatile data storage. Communications and control peripherals include I2C, SPI, AUSART, a capture/compare/PWM module, two 8-bit timers, one 16-bit timer, a watchdog timer, power-on reset, and brown-out reset. The 12-channel ADC supports analog sensing without requiring a separate converter.
The PIC16F721-E/SO combines a 16 MHz internal oscillator with 7 KB flash and 256 bytes of SRAM, providing a practical balance between code space, data handling, and processing speed. Its 18 I/O pins allow digital control signals, sensor inputs, and actuator outputs to be integrated around a single controller. In-circuit serial programming supports manufacturing, development, and field configuration without removing the device from its circuit.
Typical applications include industrial sensor controllers, digital thermometers, motor and valve control, compact power supplies, building-control modules, data-acquisition front ends, and serial-interface equipment. The 12-bit resolution of the ADC is suitable for many industrial measurements, while I2C, SPI, and AUSART permit connection to sensors, displays, transceivers, and service ports.
When laying out the PCB, reserve the programming interface and stable decoupling close to the appropriate device pins, and route sensitive analog inputs away from switching nodes. Confirm the device's specified operating limits and automotive temperature designation against the manufacturer datasheet before deploying it in safety-critical or vehicle applications.
This product overview combines the PIC16F721-E/SO electrical identity, peripheral capabilities, package details, application guidance, and pin-compatible replacement considerations into an engineering-focused reference for schematic design, firmware planning, PCB layout, and sourcing.
جێگرەوەکانی جێگۆڕکێ بۆ PIC16F721-E/SO — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ PIC16F721-E/SO (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, I/O Pins, Instruction Set, Core Architecture, Internal Oscillator.
PIC16F721-I/SO
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →PIC16F721T-I/SO
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →PIC16F720-I/SO
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →PIC16F722-I/SO
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →PIC16F1936T-I/SO
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
PIC16F721-E/SO زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Product Type | 8-bit RISC microcontroller |
| زۆرترین فرێکوێنسیی کاتژمێر | 16 MHz |
| Program Memory | 7 KB flash (4K x 14) |
| Data Memory | 256 B SRAM |
| Non-Volatile Data Memory | 128 B |
| General-Purpose I/O | 18 I/O |
| ADC Resolution | 8 bit |
| ADC Channel Count | 12 channels |
| Operating Voltage | 2.5 V, 3.3 V, or 5 V |
| Instruction Set | 35 instructions |
| Stack Depth | 8 levels |
| Timer Count | Two 8-bit timers and one 16-bit timer |
| Serial Interfaces | I2C, SPI, and AUSART |
| Capture/Compare/PWM | CCP module |
| System Protection | Watchdog timer, power-on reset, and brown-out reset |
| Programming | In-circuit serial programming |
| I/O Drive Capability | 25 mA source/sink |
| پاکێج | 20-pin SOIC, 0.295 inch body width |
| جۆری دامەزراندن | Surface mount |
| Internal Oscillator | 16 MHz |
ڕێنمایی ڕێکخستنی پینی PIC16F721-E/SO 20-pin soic, 0.295 inch body width
ڕێکخستنی پین بۆ PIC16F721-E/SO (پاکێجی 20-pin soic, 0.295 inch body width). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ PIC16F721-E/SO.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
PIC16F721-E/SO گونجاوە بۆ 6 بەکارھێنانs: Industrial Sensor Controller, Digital Thermometer, Compact Motor and Valve Control, Building Automation Module, Serial Data-Acquisition Front End, Power-Supply Monitor.
Industrial Sensor Controller
The PIC16F721-E/SO fits industrial sensor nodes that combine several analog measurements with local digital control. Its 12-channel, 8-bit ADC can monitor pressure, temperature, level, or potentiometer signals, while 18 I/O provide inputs, alarm outputs, and digital interlocks. The 16 MHz core gives sufficient headroom for filtering, calibration, communications, and supervisory logic. I2C or SPI can connect remote sensors, while AUSART supports service links or local displays. A key design consideration is keeping analog routing away from switching nodes and programming signals.
پێشنیارکراو
Digital Thermometer
A compact PIC16F721-E/SO measurement system can use its 12-channel ADC to digitize a resistive or ratiometric temperature sensor without a separate ADC. The controller can apply calibration, filtering, and hysteresis, then display or transmit the result through I2C, SPI, or AUSART. Its 7 KB flash is sufficient for lookup tables and conversion routines, while the 256-byte SRAM supports temporary measurements and communication buffering. For accurate results, use a quiet reference arrangement, separate analog and digital return paths, and calibrated timing rather than relying on raw conversion codes alone.
پێشنیارکراو
Compact Motor and Valve Control
The PIC16F721-E/SO can control compact motors, solenoids, or valves where deterministic pulse timing and manageable I/O count are important. Its 16 MHz clock supports the CCP module and timer resources used to generate pulse-width-modulated actuator commands, monitor feedback switches, and coordinate interlocks. The 25 mA source/sink I/O capability is suitable for control signals, while external transistors or drivers should handle higher current. Firmware should include startup limits, watchdog recovery, and safe-state behavior when a sensor or communication timeout occurs.
پێشنیارکراو
Building Automation Module
PIC16F721-E/SO-based building modules can monitor environmental sensors and drive lighting, HVAC, or occupancy-related outputs. The 18-I/O count allows multiple discrete inputs and relay-control signals, and the three principal serial interfaces support local sensors, remote nodes, and service equipment. Its 256-byte SRAM and 7 KB flash support moderate protocol handling without requiring a high-performance processor. In building equipment, enforce watchdog recovery and define safe output states during reset or communications failure. The 12-channel ADC can also supervise analog feedback from sensors and power rails.
پێشنیارکراو
Serial Data-Acquisition Front End
The PIC16F721-E/SO can serve as a modest data-acquisition front end when samples do not require continuous high-rate streaming. Engineers can scan up to 12 analog channels through the ADC, apply scaling and filtering, and transfer results using SPI, I2C, or AUSART. Its 16 MHz processing speed supports deterministic sampling tasks and protocol overhead, while flash accommodates calibration tables and configuration logic. Keep the converter input impedance, source impedance, and acquisition timing within the manufacturer recommendations, and avoid loading sensitive sensor outputs during multiplexed scans.
پێشنیارکراو
Power-Supply Monitor
PIC16F721-E/SO is suitable for monitoring and supervisory control in compact power modules because the ADC can sample voltage, current, or temperature feedback while the CCP and timers support control functions. The device can coordinate enable sequencing, fault flags, and data reporting through I2C, SPI, or AUSART. Its brown-out reset and watchdog features improve recovery behavior, although the power stage still requires independent protection. Design the sensing network so switching-node transients do not saturate the ADC input, and keep the MCU supply and ground arrangement robust against regulator output ripple.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ PIC16F721-E/SO — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | PIC16F721-I/SO | PIC16F721T-I/SO | PIC16F720-I/SO | PIC16F722-I/SO | PIC16F1936T-I/SO |
|---|---|---|---|---|---|---|
| Package | SOIC-20 | SOIC-20 | SOIC-20 | SOIC-20 | SOIC-20 | SOIC-20 |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| CPU Type | 8-bit RISC | 8-bit RISC | 8-bit RISC | 8-bit RISC | 8-bit RISC | 8-bit RISC |
جیاکەرەوە سەرەکییەکان
- Closest alternate ordering configuration (بەراورد بەPIC16F721-I/SO)
- Documented same-family grading option (بەراورد بەPIC16F721T-I/SO)
- Related family alternative with PCB reuse (بەراورد بەPIC16F720-I/SO)
- Expanded advanced-family option (بەراورد بەPIC16F1936T-I/SO)
تێبینییەکانی دیزاین
Place the MCU decoupling capacitor at the VDD and VSS pins using the shortest, lowest-inductance connection available. Keep the programming interface and its signal traces accessible without crossing sensitive analog inputs. Because this device combines high-speed digital activity with multiplexed ADC channels, route analog returns directly to the device ground reference and avoid sharing narrow paths with switching or relay-control currents.
Treat analog and digital layout as separate subsystems within the same controller. Connect sensor returns to the device-side ground point, keep ADC traces short, and separate them from I2C, SPI, AUSART, timer, and programming routes. If the measured source has high impedance, account for acquisition time and sampling capacitance in the channel-switching sequence. Validate the selected firmware configuration and pin multiplexing against the manufacturer's pin-description table.
The PIC16F721-E/SO supports 2.5 V, 3.3 V, and 5 V operation, but the selected supply voltage must also match the external sensors and communication devices. Check input and output limits in the manufacturer electrical-characteristics tables before applying a rail. Use brown-out reset behavior that suits the system, and ensure the firmware places outputs in a defined state during reset, watchdog recovery, and startup.
Do not treat equal package dimensions as proof of software or peripheral compatibility. A replacement must be checked for power pins, oscillator functions, programming signals, ADC channels, CCP outputs, timer assignments, interrupt vectors, configuration bits, and register behavior. For the closest same-family alternatives, preserve the exact Microchip ordering suffix and validate programming with the intended production toolchain before releasing a new PCB revision.
زانیاری پابەندبوون
The exact compliance declarations and qualification status for the PIC16F721-E/SO suffix require confirmation from the manufacturer product and ordering documentation. The E suffix should not be treated as proof of AEC-Q100 qualification without the applicable Microchip documentation.