Texas Instruments

SN65HVD53D - High-Output Full-Duplex RS-485 Transceiver | Texas Instruments

MPN: SN65HVD53D ✓ چالاک
1 uA (both driver and receiver disabled) Id RS-485, RS-422 Rds(on) SOIC (D), 14 pins, 3.90 mm width, 0.154 inch pitch Package
MOQ: 1 |

SN65HVD53D گشتی

The Texas Instruments SN65HVD53D is a high-output, full-duplex RS-485 and RS-422 transceiver with driver and receiver enable pins, packaged in a 14-pin SOIC (D). It combines one differential driver and one differential receiver with independent active-high driver enable (DE) and active-low receiver enable (RE) control, and it offers a 1/8 unit-load receiver option supporting up to 256 nodes on a single bus.

A transceiver is the physical-layer interface that converts between a logic-level digital signal and a balanced differential line pair. An RS-485 transceiver belongs to the differential line-driver / receiver family, which sits under interface ICs, communication ICs, and ultimately semiconductor ICs. Differential signaling carries the same data on two wires of opposite polarity, so common-mode noise induced along the cable is rejected by the receiver, making RS-485 the dominant industrial bus for factory automation, instrumentation, and building control.

Key differentiators of this device include bus-pin ESD protection exceeding 15 kV HBM, selectable driver output transition times supporting signaling rates of 1 Mbps, 5 Mbps and 25 Mbps, a low-current standby mode drawing about 1 uA when both the driver and receiver are disabled, and glitch-free receiver outputs. The 14-pin SOIC body measures 3.90 mm wide and is rated for -40 C to +85 C operation, covering industrial temperature ranges without a hermetic or extended package.

Internally, the SN65HVD53D uses a differential driver stage with selectable slew rate to control edge energy on the bus and limit EMI, while the receiver front end presents a low unit load so many nodes can share one cable run. Enable pins give the system designer direct control over bus direction and shutdown, which is valuable in multi-drop networks where multiple transceivers must not all drive simultaneously.

Typical deployments include industrial RS-485 field buses, PLC and remote I/O links, building HVAC and access-control networks, utility and metering equipment, and instrumentation links where a full-duplex point-to-point topology with separate driver and receiver enables is required.

When laying out the board, keep the differential pair tightly coupled with a continuous ground reference beneath it, place the bypass capacitors at the supply pins, and treat the enable pins as digital control signals that must be sequenced so that only one node drives the bus at a time.

This page consolidates device specifications, enable-logic differences against sibling family members, drop-in alternatives, and practical layout guidance into a single engineering reference that goes beyond a basic catalogue entry.

جێگرەوەکانی جێگۆڕکێ بۆ SN65HVD53D — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ SN65HVD53D (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Operating Temperature Range, Standby Current, Product Type, Maximum Bus Nodes.

Texas Instruments
Package: 8-pin SOIC (D), 0.154 inch body width, 3.90 mm width
Operating Temperature Range: -40 °C to +85 °C
Standby Current: 1 µA
بەراوردکردن لەگەڵ SN65HVD53D →
Texas Instruments
Package: 8-pin SOIC (D)
Operating Temperature Range: -40 °C to 85 °C
Standby Current: Less than 1 µA
بەراوردکردن لەگەڵ SN65HVD53D →
Texas Instruments
Package: 14-pin SOIC (D)
Standby Current: 1 µA
Product Type: High-output full-duplex RS-485 driver and receiver
بەراوردکردن لەگەڵ SN65HVD53D →
Texas Instruments
Package: 14-pin SOIC (D)
Operating Temperature Range: -40°C to +85°C
Standby Current: 1 µA
بەراوردکردن لەگەڵ SN65HVD53D →

SN65HVD54D

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 SOIC (D), 14 pins
High-output full-duplex RS-485 driver and receiver · 1 transmitter and 1 receiver · RS-422 and RS-485 · 5 Mbps · 5 V · 1/8 unit load · 256 nodes · Exceeds 15 kV HBM

پەیوەندی بۆ نرخ

بینینی داتاشیت →

SN65HVD55D

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 SOIC (D), 14 pins
Full-duplex RS-485 driver and receiver with enables · RS-422 and RS-485 · 1 transmitter and 1 receiver · 1 Mbps · 50 mV · 1/8 unit load · 256 nodes · Exceeds 15 kV HBM

پەیوەندی بۆ نرخ

بینینی داتاشیت →

SN65HVD52D

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 SOIC (D), 14 pins
RS-485 / RS-422 full-duplex transceiver · 1 driver and 1 receiver · 1 Mbps · 5 V · 5.5 V · -40 C to +85 C · 8-pin SOIC (D) · Surface mount

پەیوەندی بۆ نرخ

بینینی داتاشیت →

SN65HVD51D

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 SOIC (D), 14 pins
RS-422/RS-485 full-duplex transceiver · 1 driver · 1 receiver · 5 Mbps · 4.5 V to 5.5 V · RS-422 and RS-485 · Full-duplex · 1/8 unit load

پەیوەندی بۆ نرخ

بینینی داتاشیت →

SN65HVD50D

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 SOIC (D), 14 pins
High-output full-duplex RS-485 driver and receiver · RS-485 and RS-422 · 4.5 V to 5.5 V · 25 Mbps · 1 · 1 · 50 mV · 1/8 unit load

پەیوەندی بۆ نرخ

بینینی داتاشیت →

SN65HVD53D تایبەتمەندییەکان

Device Type Full-duplex RS-485 / RS-422 transceiver with enables
Number of Drivers / Receivers 1 / 1
Driver Enable Polarity Active-high
Receiver Enable Polarity Active-low
Unit Load Option 1/8 unit-load option available (up to 256 nodes on the bus)
Maximum Nodes on Bus 256 nodes
Bus Pin ESD Protection Exceeds 15 kV HBM
Driver Output Transition Time Options 1 Mbps, 5 Mbps and 25 Mbps signaling rates
Standby Current 1 uA (both driver and receiver disabled)
Receiver Output Glitch-free
Standards Supported RS-485, RS-422
مەودای پلەی گەرمیی کارکردن -40 C to +85 C
پاکێج SOIC (D), 14 pins, 3.90 mm width, 0.154 inch pitch
جۆری دامەزراندن Surface mount

ڕێکخستنی پینی SN65HVD53D

SOIC-14 (3.9mm) Package Pinout Diagram SOIC-14 14-pin small outline IC, 3.9x8.7mm, P1.27mm, JEDEC MS-012. Pin 1 by chamfer. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 SOIC-14 (3.9mm)
پین 1 RE — Receiver enable, active-low; pulling low enables the receiver
پین 2 DE — Driver enable, active-high; pulling high enables the driver
پین 3 D — Driver data input
پین 4 GND — Ground
پین 5 GND — Ground
پین 6 Y — Receiver inverting output
پین 7 A — Driver non-inverting output / receiver non-inverting input
پین 8 GND — Ground
پین 9 GND — Ground
پین 10 B — Driver inverting output / receiver inverting input
پین 11 Z — Receiver non-inverting output
پین 12 R — Receiver data input
پین 13 VCC — Power supply
پین 14 VCC — Power supply

بەکارهێنانە باوەکان

SN65HVD53D گونجاوە بۆ 6 بەکارھێنانs: Industrial RS-485 Field Bus and PLC Remote I/O, Building HVAC, Access Control and Sensor Networks, Utility Metering and Energy Monitoring, Instrumentation and Test & Measurement Front Panels, Medical and Diagnostic Equipment Links, Data Center and Telecom Remote Equipment.

🏭

Industrial RS-485 Field Bus and PLC Remote I/O

The SN65HVD53D suits factory automation links where a controller talks to remote I/O modules over a long twisted pair. The 1/8 unit-load receiver option lets up to 256 nodes share one bus segment, which removes the need for repeaters in sprawling sensor and actuator networks. Because the driver is a high-output stage, the bus can drive heavily terminated cables at 1 Mbps or 5 Mbps signaling rates, and the selectable output transition times control edge energy to limit EMI in cabinets full of switching equipment. The active-high DE and active-low RE pins let the host processor arbitrate bus direction in software, preventing contention when several nodes may transmit. Operating from -40 C to +85 C, it is suited to unheated enclosures and outdoor cabinets alike.

🏠

Building HVAC, Access Control and Sensor Networks

In building-automation networks, the SN65HVD53D provides a robust differential link between a supervisory controller and field panels for HVAC, lighting and access control. Full-duplex capability lets the controller transmit requests and simultaneously receive telemetry such as temperature, valve position or door state over the same cable run. Bus-pin ESD protection exceeding 15 kV HBM is valuable when field wiring is routed through occupied rooms where maintenance transients are likely. The 1 uA standby current suits controllers that duty-cycle the bus, and the 14-pin SOIC footprint keeps the design compact enough for DIN-rail and wall-mount enclosure constraints.

⚡

Utility Metering and Energy Monitoring

Electric, gas and water metering endpoints are typically distributed across street cabinets and pits, where long cable runs and cost sensitivity dominate. The SN65HVD53D's high-output driver supports terminated RS-485 buses at 1 Mbps without active repeaters, while the 1/8 unit-load receiver option allows up to 256 meters on a single segment. Glitch-free receiver outputs avoid false data during bus turn-around, which matters when meters report short energy-delta frames. Low-current standby of about 1 uA is equally important for battery-assisted endpoints that spend most of their life asleep and only wake to transmit a reading.

🔧

Instrumentation and Test & Measurement Front Panels

Laboratory and field instrumentation racks often need to talk to remote sensors over a differential bus while keeping the host controller free from bit errors. The SN65HVD53D's selectable driver transition times are useful here because a test bench can operate at 1 Mbps for short cables or drop to the 5 Mbps and 25 Mbps grades on short, clean links where latency matters. Bus-pin ESD protection exceeding 15 kV HBM protects the receiver when operators connect and disconnect leads. Because the device offers full-duplex operation with separate enables, a single pair of transceivers can run an instrument head in one direction while configuration data returns in the other, simplifying firmware state handling.

💊

Medical and Diagnostic Equipment Links

Diagnostic analyzers and patient-monitoring carts often serialize results and control data to peripheral modules across a bench-length RS-485 link. The SN65HVD53D's low standby current of about 1 uA suits cart-based systems that power down between procedures, while the 14-pin SOIC package leaves board area for the analog front end. Because the receiver supports a 1/8 unit load, several modules can share a single bus without adding repeaters, which keeps wiring simple in carts where every extra cable is a reliability risk. For designs where isolation is required above the transceiver, the isolation boundary should be implemented separately at the digital side, keeping the RS-485 stage handling only the physical layer.

🖥️

Data Center and Telecom Remote Equipment

Remote equipment shelves, environmental monitors and out-of-band management controllers in data centers and telecom cabinets use RS-485 for housekeeping signals that sit outside the main Ethernet traffic path. The SN65HVD53D is a good fit for these management links because the high-output driver drives long in-cable runs at 1 Mbps, and the bus-pin ESD rating exceeding 15 kV HBM helps during hot-plug maintenance of field wiring. Enabling the transceiver only while the management controller polls keeps the node in the 1 uA standby state, reducing idle consumption across hundreds of managed devices. The wide 14-pin SOIC footprint is widely supported by board assemblers, which matters when consolidating several management interfaces on one carrier board.

کورتەی بەرهەمە پێشنیارکراوەکان

TJA1057GTKZ NXP Semiconductors بەکارهێنراوە لە: Industrial RS-485 Field Bus and PLC Remote I/O TLE6257SJXUMA1 Companion CAN/RS-485 style industrial interface companion بەکارهێنراوە لە: Industrial RS-485 Field Bus and PLC Remote I/O SP485EMN-L/TR MaxLinear بەکارهێنراوە لە: Industrial RS-485 Field Bus and PLC Remote I/O KSZ9897RTXI Microchip Technology بەکارهێنراوە لە: Building HVAC, Access Control and Sensor Networks ADM485JNZ Analog Devices بەکارهێنراوە لە: Building HVAC, Access Control and Sensor Networks KSZ8721SLI Microchip Technology بەکارهێنراوە لە: Building HVAC, Access Control and Sensor Networks SN65HVD37D Texas Instruments بەکارهێنراوە لە: Utility Metering and Energy Monitoring LAN9354T/ML Microchip Technology بەکارهێنراوە لە: Utility Metering and Energy Monitoring SP232ECN-L/TR MaxLinear بەکارهێنراوە لە: Utility Metering and Energy Monitoring AD779JN Analog Devices بەکارهێنراوە لە: Instrumentation and Test & Measurement Front Panels ADS1254E Texas Instruments بەکارهێنراوە لە: Instrumentation and Test & Measurement Front Panels ISO1042BDWR Texas Instruments بەکارهێنراوە لە: Instrumentation and Test & Measurement Front Panels, Medical and Diagnostic Equipment Links ISO122JUE4 Texas Instruments بەکارهێنراوە لە: Medical and Diagnostic Equipment Links MCP6043-E/P Microchip Technology بەکارهێنراوە لە: Medical and Diagnostic Equipment Links LAN9353T/PT Microchip Technology بەکارهێنراوە لە: Data Center and Telecom Remote Equipment DP83822HRHBT Texas Instruments بەکارهێنراوە لە: Data Center and Telecom Remote Equipment MAX3070EESD+ Maxim Integrated بەکارهێنراوە لە: Data Center and Telecom Remote Equipment
What is the SN65HVD53D?
The SN65HVD53D is a high-output, full-duplex RS-485 and RS-422 transceiver from Texas Instruments that integrates one differential driver and one differential receiver in a 14-pin SOIC package. According to the TI SN65HVD53 product documentation, the driver enable is active-high and the receiver enable is active-low, so bus direction can be switched in hardware. The device also offers a 1/8 unit-load receiver option supporting up to 256 nodes on one bus, bus-pin ESD protection exceeding 15 kV HBM, and selectable output transition times for 1 Mbps, 5 Mbps and 25 Mbps signaling.
What are the key specifications of SN65HVD53D that engineers should know?
The SN65HVD53D is a 1-driver / 1-receiver full-duplex RS-485 and RS-422 transceiver in a 14-pin SOIC (D) package rated from -40 C to +85 C. Key figures from the TI SN65HVD53 datasheet include a 1/8 unit-load option supporting up to 256 nodes on the bus, bus-pin ESD protection exceeding 15 kV HBM, selectable driver output transition times for 1 Mbps, 5 Mbps and 25 Mbps signaling rates, a low-current standby mode of about 1 uA when both driver and receiver are disabled, and glitch-free receiver outputs.
Where can I download the SN65HVD53D datasheet PDF?
The authoritative SN65HVD53D documentation is the manufacturer datasheet available through the Texas Instruments product page for SN65HVD53 and the linked part-details entry for SN65HVD53D. Use the pin-configuration table and the Recommended Operating Conditions section from that document when assigning pins or sizing terminations. Third-party document mirrors also host a PDF copy of the SN65HVD53D datasheet, but the manufacturer-hosted file should be treated as the controlling revision for design sign-off.
Where can I find the SN65HVD53D pinout?
The SN65HVD53D pinout is a 14-lead SOIC (D) arrangement whose DE and RE enable pins are located at the top of the device, with the logic-side pins D, R, Z and Y on one edge and the bus-side pins A and B on the other. Use the pin-configuration diagram and the Pin Functions table in the TI SN65HVD53 datasheet to confirm the exact numbering, including which ground leads tie the logic return to the bus return. Keep the exposed description on this page aligned with that table whenever the device is placed on a new board.
What is the difference between SN65HVD53D and SN65HVD52D?
The main functional difference is the enable architecture. According to the TI product documentation, the SN65HVD53, SN65HVD54 and SN65HVD55 have active-high driver enables and active-low receiver enables, while the SN65HVD50, SN65HVD51 and SN65HVD52 are fully enabled with no external enabling pins. Both families are differential half-duplex-capable transceivers in the same 14-pin SOIC class, but the SN65HVD52D leaves the enable positions unused, so a board that drives DE and RE for direction control must be reworked before substituting.
SN65HVD53D vs SN65HVD51D - which is better for an industrial bus?
Choose the SN65HVD53D when your design must switch bus direction or shut the transceiver down under software control, because it exposes an active-high driver enable and an active-low receiver enable. Choose the SN65HVD51D when the node always transmits and receives on the same schedule and you want to save control-GPIO and simplify firmware. Both are single-channel differential transceivers intended for RS-485 and RS-422 links, and both target industrial temperature grades, so the deciding factors are enable availability and bus-topology management rather than raw data rate.
Is SN65HVD53D the same as SN65HVD52D?
No, they are not interchangeable in every design. The SN65HVD53D provides active-high driver enable and active-low receiver enable pins that let the host processor control direction, while the SN65HVD52D has no external enabling pins. Both devices are 14-pin SOIC RS-485 transceivers, so the footprint matches, but a board that relies on the enable pins to avoid bus contention cannot use the SN65HVD52D without tie-offs and firmware changes.
What can replace the SN65HVD53D?
The closest drop-in candidates are the sibling Texas Instruments devices in the same 14-pin SOIC family: the SN65HVD54D and SN65HVD55D, which share the active-high driver enable and active-low receiver enable arrangement of the SN65HVD53D, and the SN65HVD52D, SN65HVD51D and SN65HVD50D, which are fully enabled and therefore require enable pins to be tied off. Because the enable architecture differs within the family, always re-check the pin-functions table and the transceiver enable logic of the exact replacement before releasing a new PCB spin.
What is the best alternative to the SN65HVD53D from another manufacturer?
Cross-manufacturer drop-in options for this exact 14-pin SOIC full-duplex transceiver with separate enables are limited, and many competing RS-485 devices use 8-pin or 16-pin packages with different enable polarity. For a new design, evaluate the Texas Instruments SN65HVD54D and SN65HVD55D, which keep the same footprint and enable logic, and compare them against your bus speed, node count and common-mode range requirements. Treat any cross-brand candidate as a footprint-level substitution only after its enable and idle-bias behavior have been verified against the manufacturer datasheet.
When should I choose the SN65HVD53D over a fully enabled transceiver?
Choose the SN65HVD53D when the node needs hardware-level bus direction control or low-power standby that is driven by a host GPIO. A fully enabled transceiver such as the SN65HVD52D or SN65HVD51D keeps the driver and receiver permanently active, which simplifies firmware but prevents the system from placing the node into a low-current sleep state of about 1 uA. The SN65HVD53D therefore suits battery-backed and duty-cycled nodes, multi-drop networks where contention must be prevented, and designs that need a clean deasserted state on the bus.
Is the SN65HVD53D suitable for industrial automation and RS-485 field buses?
Yes, the SN65HVD53D is designed for industrial RS-485 and RS-422 links and is rated for -40 C to +85 C operation. Its bus-pin ESD protection exceeding 15 kV HBM helps in electrically noisy factory environments, and the 1/8 unit-load option allows up to 256 nodes on a single bus segment. The selectable driver transition times let you match edge rate to 1 Mbps, 5 Mbps or 25 Mbps signaling, which helps control EMI on long cable runs. Confirm the actual data rate of the ordered device against your bus baud rate before layout sign-off.
How many nodes can I connect to a single SN65HVD53D bus?
With the 1/8 unit-load receiver option, a single bus can support up to 256 nodes. The TI SN65HVD53 feature list states the 1/8 unit-load option is available specifically to reach that node count, compared with the 32-node limit of a standard one-unit-load receiver. Line length, stub length, termination and data rate all reduce the practical node count, so keep transceivers evenly distributed on the trunk, avoid long stubs, and use termination only at the two physical ends of the cable.
What is the standby current of the SN65HVD53D and how is it reached?
The SN65HVD53D reaches a standby current of about 1 uA when both the driver and the receiver are disabled. The TI product documentation describes this low-current standby mode as being achieved by disabling both halves of the transceiver through the enable pins, which is exactly why the SN65HVD53 was given external enables in the first place. In firmware, assert DE low and RE high to park the device, and note that the 1 uA figure is a standby-state number rather than the active operating consumption.
What ESD protection does the SN65HVD53D provide on the bus pins?
Bus-pin ESD protection on the SN65HVD53D exceeds 15 kV HBM, according to the TI SN65HVD53 documentation. The protected pins are the A and B bus connections, which are the only pins exposed to field wiring and therefore to human touch and cable transient events. Internal protection diodes clamp the transient and return energy to the supply rails, so external protection is still recommended for long or unbonded cables in industrial installations, and the supply decoupling must be sized to absorb the injected charge.
What does the high-output SN65HVD53D drive differently from a standard RS-485 transceiver?
The high-output designation means the driver stage sources and sinks more current than a standard RS-485 driver, which allows longer cable runs, more heavily terminated buses and faster edge rates. That capability pairs naturally with the selectable transition times offered for 1 Mbps, 5 Mbps and 25 Mbps signaling, since a strong driver can switch quickly while the slew-rate option keeps edge energy controlled. The trade-off is higher supply current during transmission and potentially greater EMI, so the bus impedance, cable shield and termination strategy must be reviewed together with the data rate.
Where can I buy the SN65HVD53D and how is it priced?
The SN65HVD53D is supplied in the 14-pin SOIC (D) package and is offered as an active Texas Instruments catalog part. Current commercial terms, stock position and volume pricing are updated daily, so use the Request a Quote form on this page and state your required quantity, target date and delivery location to receive a firm quotation and availability confirmation. The same form is the fastest route to a lead-time commitment for production builds, and it lets the quote reflect reel packaging versus cut-tape requirements.
What is the lead time and minimum order quantity for the SN65HVD53D?
Lead time and minimum order quantity for the SN65HVD53D depend on current factory backlog and the packaging you choose, so no fixed number can be quoted without a live supply check. Submit the Request a Quote form on this page with your target quantity, reel or cut-tape preference, and required delivery date, and the supply desk will confirm the current lead time in writing. For prototype work the manufacturer normally ships the standard 14-pin SOIC (D) package, while production orders are typically scheduled against the tape-and-reel configuration.

داتای سەرچاوەی ئەندازیاری بۆ SN65HVD53D — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the SN65HVD53D when your node needs an active-high driver enable and an active-low receiver enable, because that combination lets firmware arbitrate bus direction, park the device in a roughly 1 uA standby state, and prevent multi-node contention in software. It is the right part for long, terminated industrial RS-485 runs at 1 Mbps, where the high-output driver and the 1/8 unit-load receiver (up to 256 nodes) genuinely help. Pick the SN65HVD54D or SN65HVD55D when you need the identical footprint and enable logic but a different output-current or signaling-rate grade. Pick the SN65HVD52D, SN65HVD51D or SN65HVD50D only for fixed-direction, always-on nodes, because they are fully enabled and the enable pins in your schematic would have to be tied off. Cross-manufacturer transceivers frequently use different 8-pin or 16-pin packages and opposite enable polarities, so treat any non-TI candidate as a board-level substitution, not a drop-in, and verify idle-bias and fail-safe behavior before releasing a new PCB spin.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە SN65HVD54D SN65HVD55D SN65HVD52D SN65HVD51D SN65HVD50D
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package SOIC (D), 14 pins SOIC (D), 14 pins - same SOIC (D), 14 pins - same SOIC (D), 14 pins - same SOIC (D), 14 pins - same SOIC (D), 14 pins - same
Driver / Receiver Count 1 / 1 1 / 1 1 / 1 1 / 1 1 / 1 1 / 1
Enable Pins Active-high DE, active-low RE Active-high DE, active-low RE Active-high DE, active-low RE None - fully enabled None - fully enabled None - fully enabled
Operating Temperature Range -40 C to +85 C -40 C to +85 C -40 C to +85 C -40 C to +85 C -40 C to +85 C -40 C to +85 C
Standards RS-485 / RS-422 RS-485 / RS-422 RS-485 / RS-422 RS-485 / RS-422 RS-485 / RS-422 RS-485 / RS-422

جیاکەرەوە سەرەکییەکان

  • Active-high driver enable and active-low receiver enable allow hardware-level bus direction control plus a low-current standby path (بەراورد بەSN65HVD52D)
  • High-output driver stage combined with selectable transition times for 1 Mbps, 5 Mbps and 25 Mbps signaling (بەراورد بەSN65HVD50D)
  • 1/8 unit-load receiver supports up to 256 nodes on a single bus segment (بەراورد بەSN65HVD51D)
  • Bus-pin ESD protection exceeding 15 kV HBM with glitch-free receiver outputs (بەراورد بەSN65HVD52D)

تێبینییەکانی دیزاین

Route the A and B differential pair as a tightly coupled, length-matched trace pair with a continuous ground plane reference directly beneath the pair. Keep the pair away from switching nodes, inductors and the edges of the board to prevent radiated noise from coupling differentially into the receiver. If the pair must cross a split in the ground plane, re-route it so the reference never breaks. Place the bus-side network (termination and any protection devices) at the connector, not at the transceiver, so surge current does not flow through long board traces.

Place the supply bypass capacitor directly across the VCC pins at the package, with a short, low-inductance return to the ground pins, and add a second bulk capacitor near the connector-side ground reference. The 15 kV HBM bus-pin protection routes injected transient current into the supply rails, so inadequate decoupling can brown out the transceiver and cause receiver errors or latch-up-like misbehavior during an ESD event. Verify that the host regulator can absorb the transient charge and that the ground pins connect to a solid plane rather than a thin trace.

Do not allow two nodes to drive the bus simultaneously: assert DE on exactly one node at a time and release it before another node transmits, otherwise the driver stages fight each other and draw large current. Use the active-high DE and active-low RE pins exactly as documented and do not tie RE high permanently if you intend to use the low-current standby path, since that keeps the receiver enabled. Also confirm the data rate of the specific ordered device against your bus baud rate before sign-off, because the family offers 1 Mbps, 5 Mbps and 25 Mbps transition-time grades.

Choose the slowest driver transition time that still meets your baud-rate budget. Slower edges reduce radiated emissions and ringing on long cables, which matters in industrial cabinets with strict EMC limits, while the high-output driver stage still allows reliable operation at 1 Mbps on terminated buses. If the bus runs at 5 Mbps or 25 Mbps on short cables, use the faster grade and consider a shield with a proper chassis-ground termination at the connector to keep common-mode currents out of the digital ground.

Estimated: for a bus operating at 5 V with a 60 ohm differential termination, the driver dissipation during transmission is roughly (5 V x 2 mA driver current) plus the load contribution of about 5 V squared divided by 120 ohm, or approximately 0.2 W worst case during continuous transmit. Because this is a linear calculation and not a manufacturer figure, confirm the real driver current from the device documentation and add the quiescent consumption before sizing the supply. Where the node is duty-cycled, use the enable pins to hold the device in its roughly 1 uA standby state between transmissions.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The device is an industrial-temperature RS-485 transceiver rated -40 C to +85 C and is not an automotive-qualified part. RoHS, REACH, lead-free and halogen-free status are taken from the manufacturer product page material and are not restated here without confirmation; request the current declaration through the Request a Quote form.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

SN65HVD53D datasheet SN65HVD53D pinout SN65HVD53 datasheet pdf SN65HVD53D equivalent SN65HVD53D replacement SN65HVD53D vs SN65HVD52D SN65HVD53D price Texas Instruments SN65HVD53D SN65HVD53 14-SOIC RS-485 transceiver SN65HVD53 full duplex RS-485 with enable SN65HVD53 1/8 unit load 256 nodes bus SN65HVD53 25 Mbps signaling rate option what is the standby current of SN65HVD53

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments SN65HVD53 SN65HVD53D SN65HVD54D SN65HVD55D SN65HVD52D SN65HVD51D SN65HVD50D RS-485 transceiver RS-422 interface differential line driver differential line receiver interface IC communication IC semiconductor IC unit load common-mode rejection glitch-free receiver output ESD protection HBM human body model standby current 14-pin SOIC SOIC surface-mount package industrial field bus RoHS
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ