SN65HVD70D - 3.3V Full-Duplex RS-485 Transceiver | TI
MPN: SN65HVD70D ✓ چالاکSN65HVD70D گشتی
An RS-485 transceiver is an interface IC that converts logic-level signals to and from differential bus voltages. This differential signaling supports noise-resistant, long-distance communication between industrial, communications, and instrumentation systems. Full duplex requires separate differential driver and receiver connections, while the enable inputs allow each direction to be disabled when not required.
The SN65HVD70D operates from a 3.3 V supply and supports signaling rates up to 400 kbps. Its ESD protection includes greater than 30 kV human-body-model exposure and greater than 12 kV IEC 61000-4-2 contact discharge. These protections reduce the risk of electrostatic damage to the bus interface, although correct board-level grounding and surge design remain necessary.
The device uses differential signaling to reject common-mode noise, and its large receiver hysteresis improves tolerance of conducted differential noise. The SN65HVD70D is suitable for bidirectional links where the transmitter must remain enabled during reception or where independent direction control is required. Its 14-pin SOIC package supports conventional surface-mount assembly.
Typical uses include industrial control networks, factory automation equipment, building automation interfaces, communication adapters, and external bus-powered controllers. The separate enable controls can also simplify direction-control logic when the host controller drives the interface directly rather than using an automatic transceiver controller.
For reliable operation, route the differential pair as a tightly coupled pair, provide a low-impedance return path, place termination only at the two physical ends of the bus, and avoid stubs. Verify enable polarity and bus idle states in firmware because incorrect direction timing can create a contention condition on the bus.
This product page combines the manufacturer interface specifications with packaging guidance, application examples, comparison criteria, and drop-in replacement considerations to support faster component selection and PCB implementation.
جێگرەوەکانی جێگۆڕکێ بۆ SN65HVD70D — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ SN65HVD70D (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Maximum Data Rate, Package, Product Type, Driver Enable, Duplex Mode.
SN65HVD71D
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →SN65HVD1470D
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
SN65HVD76D
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →SN65HVD70D تایبەتمەندییەکان
| Product Type | Full-duplex RS-485 transceiver |
| ڤۆڵتیەی دابینکردن | 3.3 V |
| Maximum Data Rate | 400 kbps |
| Transceiver Configuration | 1/1 full-duplex transceiver |
| Driver Enable | Yes |
| Receiver Enable | Yes |
| IEC ESD Protection | 12 kV contact discharge |
| Human Body Model ESD Protection | >30 kV |
| Receiver Hysteresis | Large receiver hysteresis |
| پاکێج | 14-pin SOIC (D) |
| جۆری دامەزراندن | Surface mount |
ڕێنمایی ڕێکخستنی پینی SN65HVD70D 14-pin soic (d)
ڕێکخستنی پین بۆ SN65HVD70D (پاکێجی 14-pin soic (d)). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ SN65HVD70D.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
SN65HVD70D گونجاوە بۆ 6 بەکارھێنانs: Industrial Control Networks, Factory Automation Equipment, Building Automation Interfaces, Communication Adapters, Test and Measurement Equipment, External Bus-Powered Controllers.
Industrial Control Networks
The SN65HVD70D fits bidirectional control links used between PLCs, motor controllers, sensors, and remote I/O modules. Its 3.3 V supply suits modern embedded industrial equipment, while the 400 kbps maximum rate provides ample margin for command and status traffic below that limit. Differential signaling and large receiver hysteresis improve immunity to conducted noise encountered near motors and switching equipment. The independent driver and receiver enables let firmware control each direction without requiring a separate automatic transceiver controller.
پێشنیارکراو
Factory Automation Equipment
Use the SN65HVD70D for full-duplex communication between factory controllers and distributed equipment where both directions may operate simultaneously. Its 14-pin SOIC package is compatible with standard surface-mount assembly processes, and its 400 kbps rate supports many parameter-setting and diagnostic protocols. The 12 kV IEC contact-discharge protection rating adds valuable robustness at exposed bus connectors, although it does not replace properly coordinated surge protection for the installation environment.
پێشنیارکراو
Building Automation Interfaces
The SN65HVD70D is appropriate for controller boards that exchange full-duplex commands and diagnostics over an RS-485 field bus. A 3.3 V supply simplifies integration with embedded processors, while the 400 kbps rate accommodates common building-automation baud rates with margin. Large receiver hysteresis helps distinguish valid differential states in environments containing switching loads and long cable runs. Enable-controlled direction management is particularly useful where traffic can occur in both directions without half-duplex turnaround delays.
پێشنیارکراو
Communication Adapters
The SN65HVD70D can bridge a 3.3 V host controller to a full-duplex RS-485 network in gateways, protocol converters, and data-acquisition equipment. Its 400 kbps limit accommodates many industrial and instrumentation protocols while keeping the host-side logic operating from the same 3.3 V rail. Separate enable inputs provide deterministic control of transmission and reception, helping firmware avoid bus contention. The differential interface also reduces sensitivity to ground offsets when communicating between differently referenced equipment.
پێشنیارکراو
Test and Measurement Equipment
The SN65HVD70D supports instrument controllers, remote test heads, and laboratory interfaces that require a full-duplex differential link. The 3.3 V operation aligns with modern controller platforms, while the 400 kbps rate is suitable for command, status, and moderate measurement-data transfer. The receiver's large hysteresis improves noise rejection, and the 12 kV IEC ESD rating is useful where users connect cables to external equipment. For bench systems, maintain a consistent ground reference or add isolation when the remote device can develop large ground potential differences.
پێشنیارکراو
External Bus-Powered Controllers
The SN65HVD70D can be used in embedded controllers connected to an external RS-485 network through a protected connector. Its 3.3 V supply supports compact control logic, and the full-duplex architecture permits simultaneous command reception and telemetry transmission without automatic direction control. The 400 kbps rate is suitable for many embedded-control protocols. The 14-pin SOIC package leaves room for separate protection components, while 12 kV IEC contact-discharge capability strengthens the interface against handling and installation transients.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ SN65HVD70D — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | SN65HVD71D | SN65HVD1470D | SN65HVD76D |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | SOIC-14 (D) | SOIC-14 (D) | SOIC-14 (D) | SOIC-14 (D) |
| Product Type | Full-duplex RS-485 transceiver | Full-duplex RS-485 transceiver | Full-duplex RS-485 transceiver | Full-duplex RS-485 transceiver |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Maximum Data Rate | 400 kbps | 400 kbps | 400 kbps | 400 kbps |
| Transceiver Configuration | 1/1 full-duplex | 1/1 full-duplex | 1/1 full-duplex | 1/1 full-duplex |
جیاکەرەوە سەرەکییەکان
- Full-duplex operation with independent direction enables (بەراورد بەSN65HVD76D)
- 12 kV IEC contact-discharge protection (بەراورد بەSN65HVD1470D)
- Greater than 30 kV human-body-model ESD capability (بەراورد بەSN65HVD71D)
تێبینییەکانی دیزاین
Route the two RS-485 conductors as a close-coupled differential pair with continuous reference-plane support. Keep the pair geometry consistent through connectors, test points, and protection components, and avoid creating long stubs. Place optional termination networks at the two physical endpoints of the bus rather than at every node, because excessive parallel termination lowers the effective bus impedance and can impair signal quality.
Do not enable the driver while another transmitter is actively driving the same bus. Coordinate the SN65HVD70D driver-enable and receiver-enable inputs so that a node does not contend with the bus, and ensure the bus presents a valid recessive state whenever the transmitter is disabled. This is especially important in full-duplex systems that allow simultaneous traffic from multiple nodes.
Use the manufacturer pin-description table to identify every supply, ground, differential, and enable connection before layout. Keep the transceiver close to the connector and any external protection network so transient current is diverted before reaching the IC. Provide a low-impedance chassis or signal ground path, and evaluate whether galvanic isolation is required when the connected equipment can develop significant ground-potential differences.
زانیاری پابەندبوون
The manufacturer description identifies 12 kV IEC 61000-4-2 contact-discharge and greater than 30 kV human-body-model ESD protection, but separate RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations are not stated.