SN74LS699N - Synchronous Up/Down Counter | Texas Instruments
MPN: SN74LS699N ✓ چالاکSN74LS699N گشتی
A counter IC is a member of the broader digital logic hierarchy and increments or decrements a binary state in response to clock events. The 74LS699 architecture adds an output register between the counting section and the external outputs, allowing the presented value to change on a defined clock edge rather than immediately after each internal count transition. This registered architecture helps prevent data races when multiple counters or peripherals share a bus.
The principal functional features include synchronous counting in up or down directions, parallel output registers, and multiplexed three-state outputs. Synchronous operation means the counter state advances on the active clock edge, simplifying timing analysis in multi-stage digital systems. The three-state outputs can place each output in a high-impedance state when the device is not driving the shared bus, helping reduce bus contention when several compatible devices are connected.
The device belongs to the LS logic series, using bipolar TTL-compatible signal levels and standard 74LS-family interface conventions. The output-register stage separates internal counting activity from bus presentation, while the multiplexer determines which registered information appears on the output bus. Designers should consult the manufacturer pin-description table before assigning PCB tracks because each physical pin must be connected according to its dedicated clock, control, count, or output function.
Typical uses include programmable timing generators, pulse and sequence counters, industrial control logic, test-and-measurement equipment, and address or event-counting subsystems. The SN74LS699N is particularly useful when a downstream device requires stable parallel data synchronized to the system clock rather than continuously changing combinational counter outputs.
For new PCB layouts, preserve the standard 20-pin DIP footprint and route all supply pins according to the manufacturer datasheet. Avoid substituting a functionally similar counter without checking output timing, output-enable behavior, clear or load semantics, and the exact multiplexing arrangement. These details determine whether a replacement is truly pin-compatible rather than merely equivalent at a high level.
This product page combines the counter's core function with package guidance, replacement criteria, comparison data, and practical implementation notes. It is designed to help engineers identify the correct 74LS-family counter, verify bus-interface compatibility, and plan a board-level replacement without overlooking the distinctions between registered, multiplexed, and three-state output implementations.
جێگرەوەکانی جێگۆڕکێ بۆ SN74LS699N — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
74LS699N
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
DM74LS699N
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MC74LS699N
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
SN74LS699
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
74LS699N
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
SN74LS699N زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| کارکردن | Synchronous up/down counter with output registers and multiplexed three-state outputs |
| Logic Family | 74LS TTL logic |
| Counting Direction | Up or down |
| Counting Mode | Synchronous |
| Output Register | Present |
| Output Multiplexing | Multiplexed |
| Output State Control | Three-state |
| Package Type | 20-pin plastic DIP |
| جۆری دامەزراندن | Through-hole |
ڕێنمایی ڕێکخستنی پینی SN74LS699N 20-pin plastic dip
ڕێکخستنی پین بۆ SN74LS699N (پاکێجی 20-pin plastic dip). ئەم IC ی دیجیتاڵە GPIO، ڕووکارەکانی پەیوەندی (UART، SPI، I2C) و پینی وزە لەخۆدەگرێت. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ فەنکشنەکانی پینی جێگرەوە و ھەڵبژاردنەکانی ڕێکخستن. پێویستە بۆ دیزاینی سیستەمی جێگیر و ڕێکخستنی PCB.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ SN74LS699N.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
SN74LS699N گونجاوە بۆ 6 بەکارھێنانs: Programmable Sequence Counter, Address Generation and Indexing, Industrial Event-Counting System, Test and Measurement Front End, Digital Waveform and Pulse Counter, Shared-Bus Control Logic.
Programmable Sequence Counter
The SN74LS699N suits programmable sequence and timing systems because it combines synchronous up/down counting with an output register and multiplexed three-state outputs. It can count external events, select the direction, and present a stable registered state to downstream control logic. The registered output stage helps ensure that data changes at a defined clock boundary rather than immediately after an internal count transition. In a legacy controller, the device can therefore implement event-duration counting, step sequencing, or a compact state index without requiring a separate parallel-output latch. Board designers should verify the exact enable, clear, load, and output-control polarity in the manufacturer pin table before assigning logic states.
پێشنیارکراو
Address Generation and Indexing
The SN74LS699N can act as an address or index counter in older digital-control equipment, where a processor or sequencer requires a repeatable binary value for selecting a memory location, peripheral, or timing step. Synchronous up/down counting allows the direction of an address sequence to be changed without switching to a separate decrementing counter. Because the outputs are registered and can be tri-stated, the counter can release the bus when another address source becomes active. This makes the device useful in multiplexed control architectures where stable, clock-aligned data and controlled bus participation are more important than maximum counter speed.
پێشنیارکراو
Industrial Event-Counting System
In industrial event-counting systems, the SN74LS699N can accumulate pulses from sensors, position encoders, or machinery and retain the count for a controller. Direction control supports systems that need to distinguish positive and negative motion, while synchronous counting keeps state changes aligned with the external clock. The three-state outputs allow the counter to join a shared data bus without driving it continuously, which simplifies multiplexing with measurement, status, and command circuits. Legacy production equipment can benefit from the part's established 74LS interface behavior, although pulse-width, setup-time, and maximum-frequency requirements must be checked against the actual sensor and wiring conditions.
پێشنیارکراو
Test and Measurement Front End
The SN74LS699N is applicable to legacy test-and-measurement front ends that count test vectors, timing intervals, or instrument events and transfer the result to a controller. Its output register supports stable parallel-bus transfer, while the three-state capability allows multiple instruments or instrument functions to share a common data path. The up/down counting feature can support bipolar counting arrangements in which forward and reverse motion or positive and negative event directions must be accumulated. Engineers should pay particular attention to clock timing, output-enable sequencing, and bus contention prevention because the 74LS interface uses established logic levels rather than modern low-voltage signaling.
پێشنیارکراو
Digital Waveform and Pulse Counter
The SN74LS699N can serve as a pulse-counting element in digital waveform analyzers, function generators, and repetitive timing controllers. Synchronous counting allows its internal state to advance in step with the system clock, and the registered outputs provide a convenient state for downstream timing logic or a display interface. If a system must count both positive and negative directions, the direction input avoids using separate increment and decrement paths. The DIP package and long-lived 74LS function make the device especially relevant to repair and modernization of older laboratory equipment, but the system designer must confirm maximum operating frequency and setup time against the chosen clock and feedback arrangement.
پێشنیارکراو
Shared-Bus Control Logic
The SN74LS699N is well suited to shared-bus control logic because its multiplexed outputs support a high-impedance state when the device is not selected. A system controller can enable the counter during a bus cycle, capture its registered state, and then disable it before another peripheral drives the same lines. This reduces the number of separate parallel counters needed in legacy equipment and provides a practical way to implement operating-mode-dependent count values. Correct design depends on defining output-enable polarity and sequencing in the state machine. PCB implementations must also provide clean clock routing and adequate grounding so that registered outputs remain predictable during bus handshakes.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ SN74LS699N — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | 74LS699N | DM74LS699N | MC74LS699N | SN74LS699 | 74LS699N |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Fairchild Semiconductor | Motorola | Texas Instruments | Motorola |
| Package | PDIP-20 | PDIP-20 | PDIP-20 | PDIP-20 | PDIP-20 | PDIP-20 |
| Counter Function | Synchronous up/down counter | Synchronous up/down counter | Synchronous up/down counter | Synchronous up/down counter | Synchronous up/down counter | Synchronous up/down counter |
| Output Register | Present | Present | Present | Present | Present | Present |
| Multiplexed Outputs | Present | Present | Present | Present | Present | Present |
| Three-State Output Control | Present | Present | Present | Present | Present | Present |
| Logic Family | 74LS TTL | 74LS TTL | 74LS TTL | 74LS TTL | 74LS TTL | 74LS TTL |
جیاکەرەوە سەرەکییەکان
- Combines registered counting and controlled bus outputs (بەراورد بەDM74LS699N)
- Direct ordering option for standard 20-pin DIP legacy boards (بەراورد بەSN74LS699DW)
- Programmable direction with registered external state (بەراورد بە74LS699)
تێبینییەکانی دیزاین
Route the clock using the shortest practical path and keep it away from multiplexed output nets that switch rapidly. The registered architecture makes the output value predictable at clock boundaries, but poor clock routing can still create setup-time or hold-time violations before the counter registers a new state. Use a defined clock source, avoid unnecessary stubs, and maintain a continuous ground reference beneath the DIP pins.
Do not approve a replacement solely because it is labeled a 74LS699 counter. Compare the complete truth table, output-enable polarity, clear behavior, load behavior, output multiplexing, and timing specifications. A device can provide the same counting function yet differ in control polarity or bus architecture. For SN74LS699N, confirm that the candidate uses the same 20-pin DIP lead arrangement before attempting a physical substitution.
Preserve the standard 20-pin DIP footprint and provide unobstructed access for assembly and maintenance. Follow the manufacturer's pin-description table when assigning every net, especially the enable, clear, count-direction, clock, and multiplexed-output functions. Since the outputs are three-state, ensure the system controller disables the counter before another device drives the shared bus and that no pull-up or pull-down network conflicts with the intended bus topology.
Decouple the supply pins at the counter using the capacitance and placement specified by the manufacturer datasheet. TTL counter outputs can draw transient current when multiplexed buses change state, so adequate local bypass helps prevent supply disturbance from propagating into other logic. Keep high-current switching nodes and inductive loads away from the counter and provide a low-impedance ground path. Verify the design against the device's specified supply voltage rather than assuming modern low-voltage logic levels.
زانیاری پابەندبوون
The manufacturer classification identifies the SN74LS699N as a logic IC; no specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified.