Texas Instruments

SN75176AP - 5V RS-422/RS-485 Transceiver | Texas Instruments

MPN: SN75176AP ✓ چالاک
5 V Vdss ANSI EIA/TIA-422-B and ITU Recommendation V.11 Rds(on) 8-pin PDIP (P) Package
MOQ: 1 |

SN75176AP گشتی

The Texas Instruments SN75176AP is a 5 V differential bus transceiver with one driver and one receiver, half-duplex operation, and three-state driver and receiver outputs in an 8-pin PDIP package. Designed for balanced transmission lines, the device supports bidirectional communication over multipoint bus networks and meets ANSI EIA/TIA-422-B and ITU Recommendation V.11 requirements. The SN75176AP is commonly associated with RS-422 and RS-485 interface applications.

A differential bus transceiver is an interface IC that converts logic-level signals into balanced differential bus signals and reconstructs logic data from received differential signals. The differential architecture helps reject common-mode noise, while the balanced line supports reliable data transmission through electrically noisy industrial environments. In the signal-chain hierarchy, the SN75176AP is a bus transceiver, belonging to the interface-IC and communications-semiconductor categories.

The principal features include one differential driver, one differential receiver, three-state output control, and operation from a single 5 V supply. The driver and receiver enable inputs permit a half-duplex node to disable its driver while monitoring the bus, reducing contention on multipoint networks. The receiver can remain enabled during transmission when the system requires continuous bus monitoring, although the selected logic levels must be verified against the complete system design.

The monolithic bidirectional architecture combines transmitter and receiver functions on the same two-wire differential bus. This makes the SN75176AP appropriate for equipment distributed along RS-422 or RS-485 links, including industrial controllers, data-acquisition equipment, building controls, and communication adapters. Its balanced bus interface reduces sensitivity to ground-potential differences and externally coupled noise when the cable, termination, grounding, and transceiver implementation are designed correctly.

The 8-pin PDIP package supports conventional through-hole PCB assembly and straightforward inspection or rework. Logic-side pins include driver input, driver enable, receiver enable, and receiver output, while bus-side connections use the A and B differential terminals. A common ground reference is still required between communicating nodes because differential signaling suppresses common-mode noise rather than eliminating the need for a common reference.

The principal design consideration is bus configuration. Add proper termination at the physical ends of the bus, use twisted-pair cabling, avoid excessive stub lengths, and ensure only one driver actively drives the bus at a time. The SN75176AP is intended for balanced transmission lines; system designers must also evaluate biasing, protection, grounding, and protocol timing when using it in practical RS-485 networks.

This page combines verified manufacturer and distributor references with package, application, design, and selection guidance. It also distinguishes genuine same-footprint drop-in options from broader functional alternatives so engineers can make a PCB-compatible replacement decision rather than treating electrical similarity as proof of interchangeability.

جێگرەوەکانی جێگۆڕکێ بۆ SN75176AP — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ SN75176AP (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Product Type, Package, Driver Output, Operating Temperature, Receiver Output.

Renesas Electronics
Product Type: RS-485/RS-422 transceiver
Package: 8-pin DIP (8-PDIP)
بەراوردکردن لەگەڵ SN75176AP →
Texas Instruments
Operating Temperature: 0 °C to +70 °C
بەراوردکردن لەگەڵ SN75176AP →
Texas Instruments
Product Type: Differential bus transceiver
Driver Output: Three-state driver
Receiver Output: Three-state receiver
بەراوردکردن لەگەڵ SN75176AP →

SN75176BP

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-pin PDIP (P)
Differential bus transceiver · ANSI TIA/EIA-422-B, ANSI TIA/EIA-485-A, ITU V.11, ITU X.27 · 1 transmitter and 1 receiver · RS-422 and RS-485 · Multipoint transmission · Three-state driver · Three-state receiver

پەیوەندی بۆ نرخ

بینینی داتاشیت →

ISL8485IP

✅ جێگرەوەی ڕاستەوخۆ
Renesas Electronics
📦 8-pin PDIP
RS-485/RS-422 transceiver · Renesas Electronics · 1 transceiver, half-duplex · 4.5V to 5.5V · 5V · 5Mbps · RS-485 and RS-422 · 1 unit load

پەیوەندی بۆ نرخ

بینینی داتاشیت →

SN75176AP تایبەتمەندییەکان

Product Type 1/1 differential bus transceiver
ڤۆڵتیەی دابینکردن 5 V
Number of Drivers 1
Number of Receivers 1
Duplex Mode Half-duplex
Driver Output Three-state
Receiver Output Three-state
Interface Standards ANSI EIA/TIA-422-B and ITU Recommendation V.11
Bus Architecture Balanced multipoint transmission line
پاکێج 8-pin PDIP (P)
جۆری دامەزراندن Through-hole
پلەی گەرمیی کارکردن 0 °C to 70 °C
ژمارەی پین 8 pins
Transceiver Direction Bidirectional differential bus communication

ڕێکخستنی پینی SN75176AP

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
پین 1 RO — Receiver output
پین 2 /RE — Receiver enable, active low
پین 3 DE — Driver enable
پین 4 DI — Driver input
پین 5 GND — Ground
پین 6 A — Noninverting differential bus terminal
پین 7 B — Inverting differential bus terminal
پین 8 VCC — 5 V supply

بەکارهێنانە باوەکان

SN75176AP گونجاوە بۆ 6 بەکارھێنانs: Industrial RS-485 Control Networks, Building Automation and HVAC Equipment, Data Acquisition and Instrumentation, Multipoint Communication Equipment, Process and Factory Automation, Communication Adapters and Gateways.

🏭

Industrial RS-485 Control Networks

The SN75176AP suits industrial controller and sensor nodes that exchange data over a balanced two-wire RS-485 bus. Its single differential driver and receiver provide half-duplex communication, while the three-state outputs allow the transmitter to be disconnected logically during reception. The 8-pin PDIP package supports conventional through-hole assembly. Designers should preserve a common ground reference, control driver-enable timing, and verify that every node uses compatible A and B labeling because reversing the pair inverts the bus signal.

🏭

Building Automation and HVAC Equipment

The SN75176AP can connect building-control equipment to a balanced RS-485 supervisory network, allowing HVAC controllers, sensors, and gateways to communicate over a shared cable. The differential bus architecture helps reject common-mode noise present in building environments, while half-duplex operation supports economical two-wire wiring. Installation practice is critical: use twisted-pair cable, maintain one common reference conductor, avoid long unterminated stubs, and activate only one driver at a time.

📡

Data Acquisition and Instrumentation

The SN75176AP provides a practical physical-layer interface between data-acquisition equipment and remote sensors connected through a balanced bus. Its 5 V operation aligns with conventional logic systems, and the single driver and receiver support half-duplex command-and-response traffic. For reliable measurements, isolate logic and bus grounds where necessary, place protection devices at exposed connectors, and confirm that the selected transceiver’s input thresholds provide adequate noise margin for the system’s logic voltage.

🌐

Multipoint Communication Equipment

The SN75176AP is well suited to distributed equipment that shares a multipoint differential bus, such as remote I/O stations, counters, and industrial gateways. The three-state driver output lets a node stop driving the bus while its receiver listens, supporting token-passing or request-response protocols. Because multiple nodes share the same conductors, software must prevent simultaneous transmission and hardware must provide the bus biasing required during idle periods. Cable length and topology remain system-level constraints rather than guaranteed product capabilities.

🏭

Process and Factory Automation

The SN75176AP can be used in factory automation modules that connect controllers, actuators, and remote I/O over a balanced fieldbus segment. Differential signaling helps maintain data integrity when the cable passes near motors, relays, and switching equipment. The device itself is specified for a 0 °C to 70 °C operating range, so it may require a wider-temperature alternative when deployed in harsh industrial environments. Surge protection, shielded or twisted-pair cable, and proper grounding remain necessary for reliable field operation.

🖥️

Communication Adapters and Gateways

The SN75176AP is applicable in protocol converters and communication gateways that bridge a host processor with an external RS-422 or RS-485 segment. Its half-duplex architecture supports two-wire bus connections, while the receiver can provide bus-state information to the host when the firmware enables it. A complete gateway must manage direction control, detect transmission completion, handle bus contention, and apply fail-safe biasing. Exact logic-level compatibility should be verified because the supplied data identifies a 5 V supply but does not provide host-interface thresholds.

What are the key specifications of SN75176AP that engineers should know?
The SN75176AP is a 5 V, half-duplex differential bus transceiver with one driver and one receiver in an 8-pin PDIP package. According to the Texas Instruments SN75176A datasheet, it supports balanced transmission lines, provides three-state driver and receiver outputs, and meets ANSI EIA/TIA-422-B and ITU Recommendation V.11 requirements. It is intended for bidirectional communication over multipoint bus-transmission lines.
Where to download the SN75176AP datasheet PDF?
The official SN75176AP datasheet PDF is available from the Texas Instruments SN75176A product page at https://www.ti.com/lit/ds/symlink/sn75176a.pdf. The manufacturer document describes the differential bus transceiver, electrical characteristics, pin functions, and application information. No verified revision identifier or page count is repeated here because those details were not included in the supplied search data.
Where can I find the SN75176AP pinout?
The SN75176AP pinout is documented in the official Texas Instruments SN75176A datasheet at https://www.ti.com/lit/ds/symlink/sn75176a.pdf. The 8-pin PDIP device connects driver input and enable to logic signals, provides receiver output and enable, connects to the differential bus through A and B, and uses pins 5 and 8 for ground and 5 V supply. Consult the manufacturer pin configuration before wiring a replacement.
What standards does the SN75176AP support?
The SN75176AP meets ANSI Standard EIA/TIA-422-B and ITU Recommendation V.11. According to the Texas Instruments SN75176A datasheet, its balanced differential interface is designed for multipoint transmission on long bus lines in noisy environments. These standard references describe the physical signaling requirements and should not be treated as complete protocol specifications.
Is SN75176AP suitable for RS-485 networks?
Yes, the SN75176AP is suitable for RS-485 networks because it provides a balanced differential driver and receiver with three-state outputs and half-duplex bus control. According to the Texas Instruments SN75176A datasheet, the device is designed for bidirectional multipoint communication on balanced lines. The complete network still requires correct termination, biasing, grounding, protection, and controlled driver enable timing.
Where to buy SN75176AP online?
SN75176AP is available from Texas Instruments distributors, including DigiKey and Mouser. The verified distributor listing for DigiKey identifies it as a 1/1 half-duplex RS-422/RS-485 transceiver in an 8-pin PDIP, while Mouser lists it as an RS-422/RS-485 interface IC. Distributor snippets state that the part ships today, but exact stock quantity and current lead time are not included in the supplied data.
What is the price of SN75176AP as of 2026-10-28?
A verifiable unit price for SN75176AP is not included in the supplied distributor snippets, so no exact price can be responsibly stated as of 2026-10-28. The verified DigiKey, Mouser, and Octopart pages can be used to obtain current market pricing and quantity discounts. The numeric tier values in this record are zero placeholders solely because the commerce schema requires numeric prices and the source data contains no pricing figures.
What is the lead time for SN75176AP and is it in stock?
The verified DigiKey result states that SN75176AP can be bought and ships today, indicating distributor availability as of the source retrieval on 2026-10-27. However, the supplied data does not state an XAIPART stock quantity or a contractual lead time. Engineers should confirm current availability directly with the selected distributor before committing the bill of materials.
What can replace SN75176AP as a pin-compatible part?
SN75176BP is the clearest same-manufacturer, same-package replacement candidate identified in the supplied cross-reference data because it is presented as an 8-pin PDIP bipolar line transceiver. Compatibility must still be checked against the original schematic and the replacement datasheet, particularly enable polarity and electrical limits. Cross-package SOIC devices cannot be soldered directly onto the SN75176AP footprint without PCB changes.
Is ISL8485IP the same as SN75176AP?
ISL8485IP is a listed comparison candidate for the SN75176AP, but the supplied data does not explicitly establish a manufacturer-authorized pin-to-pin equivalence. According to the available comparison information, it is an 8-pin DIP differential bus transceiver, making it worth detailed review. Before substitution, verify pin functions, supply voltage, driver enable polarity, receiver enable behavior, and all timing limits in the applicable manufacturer datasheets.
When should I choose SN75176AP instead of another RS-485 transceiver?
Choose the SN75176AP when the design specifically requires the Texas Instruments SN75176A function in an 8-pin PDIP footprint and the verified operating range of 0 °C to 70 °C is acceptable. It provides one balanced driver, one balanced receiver, half-duplex operation, and three-state outputs for multipoint buses. Select a different device when the design needs lower power, fail-safe biasing, wider temperature range, smaller package, or additional channels.
SN75176AP vs SN75176BP: which is better for a new design?
SN75176AP is the listed 8-pin PDIP orderable variant for the SN75176A transceiver, while SN75176BP appears in the supplied cross-reference results as another Texas Instruments 8-pin PDIP bipolar line-transceiver option. The exact differences in temperature range, revision status, and electrical limits are not provided in the search snippets. For a new design, compare the complete manufacturer datasheets rather than treating the similar names as identical.
What is the best drop-in replacement for SN75176AP?
SN75176BP is the best-supported drop-in replacement candidate in the supplied evidence because it shares the Texas Instruments transceiver family and is identified as an 8-pin PDIP part. ISL8485IP is also an 8-pin DIP candidate, but the available evidence does not provide complete electrical equivalence. Confirm pin compatibility and operating limits before using either part as a production replacement.
How should the SN75176AP be connected to an RS-485 bus?
The SN75176AP uses its A and B pins for the balanced bus connection, while the logic interface provides the driver input, driver enable, receiver output, and receiver enable. According to the Texas Instruments SN75176A datasheet, the device is intended for balanced transmission lines. Add termination only at the physical ends of the bus and control driver enable so that no more than one node drives the bus at once.
What thermal or power information should be checked before using SN75176AP?
The SN75176AP operates from a 5 V supply, but the verified snippets do not provide supply-current limits, power dissipation, junction temperature, or package thermal resistance. According to the Texas Instruments SN75176A datasheet, those values must be checked under the actual output-load and bus conditions. This page does not infer them because doing so could produce an unreliable thermal design.

داتای سەرچاوەی ئەندازیاری بۆ SN75176AP — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose SN75176AP when a design needs the Texas Instruments SN75176A differential bus transceiver in an 8-pin PDIP package and its verified 0 °C to 70 °C range is suitable. Its one-driver, one-receiver, half-duplex arrangement is appropriate for balanced multipoint buses requiring shared two-wire connections. Choose SN75176BP when it is the approved Texas Instruments alternate for an existing 8-pin PDIP design, after confirming its exact electrical and lifecycle data. Consider ISL8485IP only after reviewing its manufacturer datasheet for enable polarity, supply current, thresholds, timing, temperature range, and fail-safe behavior. Do not select SOIC alternatives such as MAX3243EIDW or ISL8485IPZ as literal drop-in parts for an existing SN75176AP PCB because their packages differ.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە SN75176BP ISL8485IP
Package 8-pin PDIP (P) 8-pin PDIP (P) 8-pin PDIP
Brand Texas Instruments Texas Instruments Renesas Electronics
Product Type Differential bus transceiver Line transceiver Differential bus transceiver

جیاکەرەوە سەرەکییەکان

  • Established same-family 8-pin PDIP replacement path (بەراورد بەISL8485IP)
  • Documented multipoint balanced-bus positioning (بەراورد بەISL8485IP)
  • Three-state control for shared-bus nodes (بەراورد بەSN75176BP)

تێبینییەکانی دیزاین

Route the A and B bus conductors as a pair and keep the differential path continuous through the transceiver and connector. Place any termination network near the physical bus endpoint, not beside every node. Minimize stub branches because unterminated branches act as discontinuities that can produce reflections and alter the differential signal seen by the receiver.

Provide a stable 5 V supply and place local high-frequency bypass capacitance close to the transceiver supply and ground pins. Keep the return-current path continuous and use a common reference conductor between communicating nodes. The verified source data does not specify supply-current limits or decoupling requirements, so capacitor selection and current budget must be confirmed using the manufacturer datasheet.

Do not allow two nodes to enable their drivers simultaneously on a shared bus. Confirm driver-enable and receiver-enable polarity in the schematic, and verify whether the receiver should remain enabled during transmission. Also check A and B labeling at every connector because reversing the pair reverses the received signal. Bus biasing may also be required when no transmitter is active.

Use twisted-pair cabling, maintain a common ground reference, and apply suitable transient protection at connectors exposed to industrial cabling. Keep the differential bus away from switching-node areas and high-current return paths. Protection-device capacitance and clamp behavior can affect the bus waveform, so their suitability for the required signaling rate and bus topology must be verified.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The supplied verified snippets do not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status for SN75176AP. No compliance claim has been inferred. AEC-Q100 is marked not_applicable because the product is a commercial communications interface IC and no automotive qualification is stated.

داتا پشتڕاستکراوەتەوە لە: 2026-10-28 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

SN75176AP SN75176AP datasheet PDF Texas Instruments SN75176AP SN75176AP RS-485 transceiver SN75176AP 8-pin PDIP SN75176AP pin configuration SN75176AP industrial bus application SN75176AP vs SN75176BP SN75176AP drop-in replacement SN75176AP buy online price what can replace SN75176AP SN75176AP RS-422 RS-485 interface IC

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments SN75176AP SN75176A SN75176BP ISL8485IP Renesas Electronics differential bus transceiver bus transceiver interface IC RS-422 RS-485 ANSI EIA/TIA-422-B ITU Recommendation V.11 balanced transmission line multipoint bus half-duplex communication three-state output driver enable receiver enable common-mode noise 8-pin PDIP through-hole package twisted-pair cable differential signaling communications semiconductor
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ