NXP Semiconductors

TJA1441AT/0Z - 5 Mbit/s CAN FD Transceiver, SOIC-8 | NXP

MPN: TJA1441AT/0Z ✓ چالاک
4.5 V to 5.5 V Vdss SOIC-8 (8-SO), surface mount Package
MOQ: 1 |

TJA1441AT/0Z گشتی

The NXP Semiconductors TJA1441AT/0Z is a 5 Mbit/s high-speed CAN transceiver with integrated Silent mode, supplied in an 8-pin SOIC (SO-8) surface-mount package. It provides one CAN TXD and one RXD logic interface, a VIO pin for 3.3 V and 5 V microcontroller compatibility, and a standard ISO 11898-2 compliant CAN bus driver and receiver stage.

A CAN transceiver is the physical-layer interface between a host controller and the CAN bus wiring. It converts logic-level TXD into differential CANH and CANL bus signals, and converts received differential bus levels back into a logic-level RXD signal. In the equipment hierarchy the TJA1441AT/0Z sits between the CAN controller (microcontroller or dedicated CAN controller) and the transceiver, part of the CAN controller > CAN transceiver > physical-layer interface > interface IC chain.

Key features include a data rate of up to 5 Mbit/s, a Silent mode that puts the transmitter into a recessive, high-impedance state while the receiver stays active, a VIO supply pin that allows the logic side to run from 1.8 V up to 5.5 V, and low quiescent current for reduced system power. The device also features bus fault and short-circuit protection on the CANL and CANH pins, plus thermal shutdown and an extended operating temperature range suitable for industrial equipment.

Internally the transceiver combines a CMOS-compatible logic input stage, a differential line driver with a wide common-mode range, and a complementary differential receiver with hysteresis for noise immunity. Because the Silent mode holds the driver in recessive state, a node can stay connected to an active bus without contributing error frames, which is useful in partially powered or listen-only nodes and in test and diagnostic setups. The VIO pin independently powers the digital interface, so the TXD and RXD pins remain compatible with 3.3 V and 5 V microcontrollers while the transceiver core runs from the standard 5 V rail.

Typical applications include automotive and industrial body control modules, gateway and aggregator units, electric vehicle powertrain controllers, instrumentation clusters, sensor hub nodes, and factory automation equipment where a CAN bus backbone links remote nodes over long cable runs.

When designing with the TJA1441AT/0Z, terminate the bus with 120 ohm resistors at both ends only, keep the CANH and CANL traces as a tightly coupled differential pair, and follow the layout guidance in the NXP TJA1441 data sheet. The VIO decoupling capacitor should be placed directly on the VIO pin for clean logic levels.

This page brings together the manufacturer data sheet information, pin-level detail, cross-reference drop-in alternatives, and practical layout and application guidance so engineers can qualify the TJA1441AT/0Z quickly and design a compliant CAN node around it.

جێگرەوەکانی جێگۆڕکێ بۆ TJA1441AT/0Z — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ TJA1441AT/0Z (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Operating Temperature, Product Type, Package, Maximum Data Rate, RoHS Status.

Texas Instruments
Operating Temperature: -40°C to +125°C
Product Type: CAN FD Transceiver
RoHS Status: Compliant
NXP Semiconductors
Operating Temperature: -40C to +125C
Package: SO-8 (8-pin SOIC)
RoHS Status: Compliant
NXP Semiconductors
Operating Temperature: -40°C to +150°C (TJ)
Product Type: High-speed CAN FD transceiver
Package: 8-SOIC, 3.90 mm width
NXP Semiconductors
Product Type: High-speed CAN transceiver
RoHS Status: unknown

TJA1442AT/0Z

✅ جێگرەوەی ڕاستەوخۆ
NXP Semiconductors
📦 SOIC-8 (8-SO)
High-speed CAN FD transceiver · CAN and CAN FD · 1 · 1 · Half-duplex · 5 Mbps · 4.5 V to 5.5 V · 50 mV

پەیوەندی بۆ نرخ

بینینی داتاشیت →

TJA1443AT/0Z

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
NXP Semiconductors
📦 SOIC-8 (8-SO)
High-speed CAN transceiver · 5 Mbit/s · Classical CAN and CAN FD two-wire bus · ISO 11898-2:2016 · SAE J2284-1 to SAE J2284-5 · Standby, Sleep and Listen Only · VIO · EN

پەیوەندی بۆ نرخ

بینینی داتاشیت →

TJA1057T/3

✅ جێگرەوەی ڕاستەوخۆ
📦 SOIC-8 (8-SO)
Named in the NXP TJA1441 data sheet as a part the TJA1441 replaces; 5 Mbit/s but no VIO logic supply pin (VIO function absent), so one pin connection differs

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

TJA1051T/3/1

✅ جێگرەوەی ڕاستەوخۆ
NXP Semiconductors
📦 SOIC-8 (8-SO)
High-speed CAN transceiver · Up to 1 Mbit/s · 4.5 V to 5.5 V · 3 V to 5 V · Classical CAN, CAN FD · Half duplex, 1 driver / 1 receiver · SO-8 (8-pin SOIC) · Surface Mount

✓ بەردەستە

$0.4102 / یەکە

بینینی داتاشیت →

TJA1056T/3

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 SOIC-8 (8-SO)
Same SOIC-8 high-speed CAN footprint with VIO, but a lower 1 Mbit/s class bus rate versus 5 Mbit/s on the TJA1441 (-80%) and no Silent mode

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

TJA1440AT/0Z

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 SOIC-8 (8-SO)
Same NXP TJA144x family and SOIC-8 footprint; lower 1 Mbit/s class bus rate versus 5 Mbit/s on the TJA1441 (-80%), otherwise pin-to-pin

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

TJA1441AT/0Z تایبەتمەندییەکان

Product Type High-speed CAN transceiver with Silent mode
Manufacturer NXP Semiconductors
Maximum Data Rate 5 Mbit/s
Number of TX Channels 1
Number of RX Channels 1
CAN Bus Type Classical CAN / CAN FD physical layer
Supply Voltage VCC 4.5 V to 5.5 V
Logic Supply Voltage VIO 1.8 V to 5.5 V
Standby / Silent Mode Yes (Silent mode via TXD pin)
پاکێج SOIC-8 (8-SO), surface mount
ژمارەی پین 8 pins
پلەی گەرمیی کارکردن -40 C to +125 C
دۆخی چرخەی ژیان Active (per NXP product overview)

ڕێکخستنی پینی TJA1441AT/0Z

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
پین 1 TXD — Transmit data input from the CAN controller; low level selects Silent mode
پین 2 GND — Ground
پین 3 VCC — Transceiver supply voltage, 4.5 V to 5.5 V
پین 4 RXD — Receive data output to the CAN controller
پین 5 GND — Ground
پین 6 CANL — CAN bus low dominant output
پین 7 CANH — CAN bus high dominant output
پین 8 VIO — Logic supply for TXD and RXD, 1.8 V to 5.5 V

بەکارهێنانە باوەکان

TJA1441AT/0Z گونجاوە بۆ 6 بەکارھێنانs: Automotive Body Control Module, Industrial CAN Gateway and Protocol Bridge, Electric Vehicle Powertrain Controller, Industrial Sensor Hub and Remote I/O Node, Diagnostic and Test Bench CAN Interface, Instrumentation Cluster and HMI Terminal.

🚗

Automotive Body Control Module

The TJA1441AT/0Z fits a body controller because it delivers 5 Mbit/s CAN FD physical-layer signalling with an extended -40 C to +125 C operating range and a wide 4.5 V to 5.5 V VCC tolerance across automotive load-dump transients. It is placed between the body controller's CAN controller peripheral and the CANH/CANL harness pair, with pin 8 (VIO) tied to the 3.3 V logic domain so the MCU pins connect directly. The Silent mode gives the module a safe way to stay attached to the bus during flashing or diagnostics without corrupting traffic, and the SOIC-8 body is easy to inspect and rework in field service.

🏭

Industrial CAN Gateway and Protocol Bridge

In a gateway that bridges CAN to Ethernet or a fieldbus, the TJA1441AT/0Z provides the physical layer for a 5 Mbit/s CAN FD segment while the VIO pin at 1.8 V to 5.5 V lets the bridge logic run at a low voltage without level shifters. Bus fault and short-circuit protection on the CAN driver limits damage from industrial cable mis-wiring, and 120 ohm termination at both bus ends with a tight differential pair keeps reflections low over long factory cable runs. Using one transceiver family across all gateway variants also consolidates the BOM and keeps the software driver layer identical.

⚡

Electric Vehicle Powertrain Controller

An EV traction or battery management controller typically links inverter, charger and BMS nodes over CAN FD, and the TJA1441AT/0Z gives that link a 5 Mbit/s physical layer with the receiver always active for diagnostics while the transmitter can be silenced. The 4.5 V to 5.5 V VCC range matches the regulated 5 V rail common in vehicle controllers, and the independent VIO pin allows the transceiver logic to match a 3.3 V microcontroller. The extended -40 C to +125 C rating covers underhood and pack environments, while the protected CAN driver stages absorb the transients typical of long harness runs near motors.

🧩

Industrial Sensor Hub and Remote I/O Node

A remote I/O or sensor hub that gathers field sensors over a CAN backbone benefits from the TJA1441AT/0Z because the 5 Mbit/s rate keeps cycle times short when many nodes share one bus, and the low quiescent current suits always-on powered nodes. The VIO supply can be tied to the 3.3 V domain of a small microcontroller so the whole node runs from a single 5 V input, reducing board area. Silent mode supports maintenance and firmware update windows where the node must listen but not talk, and the SOIC-8 package keeps hand soldering and rework simple in field instrumentation.

🔧

Diagnostic and Test Bench CAN Interface

On a workshop diagnostic tool or a production test fixture, the TJA1441AT/0Z acts as the physical layer for a bench CAN network, and the Silent mode lets the tool connect to a running vehicle bus and observe frames without ever asserting dominance and interfering with the system under test. The 5 Mbit/s capability matches modern CAN FD diagnostic sessions on modern vehicles while still handling 500 kbit/s legacy OEM buses through the same device. The receiver stays live in Silent mode, so pass/fail monitoring of bus traffic continues while the transmitter is held recessive.

📺

Instrumentation Cluster and HMI Terminal

A display cluster or human-machine interface that pulls status data from many ECUs over CAN benefits from the TJA1441AT/0Z because 5 Mbit/s keeps a busy cluster bus responsive, while the separate VIO pin at 1.8 V to 5.5 V lets the transceiver talk to a modern display SoC directly. The 8-pin SOIC package places the transceiver next to the connector with short, well-coupled CANH and CANL escapes, which reduces radiated emissions in an enclosure packed with display and power circuitry. Its active receiver also lets the cluster implement bus-off detection and LIN-style sleep wake-up behaviour in firmware.

کورتەی بەرهەمە پێشنیارکراوەکان

TJA1442AT/0Z NXP Semiconductors بەکارهێنراوە لە: Automotive Body Control Module, Diagnostic and Test Bench CAN Interface STM32F103C8T6 STMicroelectronics بەکارهێنراوە لە: Automotive Body Control Module, Automotive Body Control Module TLE7257SJXUMA1 Infineon بەکارهێنراوە لە: Automotive Body Control Module KSZ8041RNL Microchip Technology بەکارهێنراوە لە: Industrial CAN Gateway and Protocol Bridge LAN9353T/PT Microchip Technology بەکارهێنراوە لە: Industrial CAN Gateway and Protocol Bridge STM32F103VET6 STMicroelectronics بەکارهێنراوە لە: Industrial CAN Gateway and Protocol Bridge STM32F746ZGT6E STMicroelectronics بەکارهێنراوە لە: Electric Vehicle Powertrain Controller TJA1057GTKZ NXP Semiconductors بەکارهێنراوە لە: Electric Vehicle Powertrain Controller MAX3051ESA Isolated CAN option for high-side traction links بەکارهێنراوە لە: Electric Vehicle Powertrain Controller STM32G071RBT6 STMicroelectronics بەکارهێنراوە لە: Industrial Sensor Hub and Remote I/O Node TJA1443AT/0Z NXP Semiconductors بەکارهێنراوە لە: Industrial Sensor Hub and Remote I/O Node, Instrumentation Cluster and HMI Terminal MAX3485EASD RS-485 companion for multi-protocol gateways بەکارهێنراوە لە: Industrial Sensor Hub and Remote I/O Node MAX13054 CAN bus monitor and fault detector companion بەکارهێنراوە لە: Diagnostic and Test Bench CAN Interface STM32F103R8T7 STMicroelectronics بەکارهێنراوە لە: Diagnostic and Test Bench CAN Interface STM32F429ZIT6 STMicroelectronics بەکارهێنراوە لە: Instrumentation Cluster and HMI Terminal PCA9554DWR Texas Instruments بەکارهێنراوە لە: Instrumentation Cluster and HMI Terminal
What is the TJA1441AT/0Z and what does it do?
The TJA1441AT/0Z is an 8-pin high-speed CAN transceiver from NXP Semiconductors that supports data rates up to 5 Mbit/s and adds a Silent mode feature. It converts the TXD logic signal from a CAN controller into the differential CANH and CANL bus pair, and converts the received bus levels back into an RXD logic signal. According to the NXP TJA1441 data sheet, the device is intended as a simple replacement for high-speed Classical CAN and CAN FD transceivers such as the TJA1051 or TJA1057, offering pin compatibility that avoids hardware and software redesign.
How does Silent mode work on the TJA1441AT/0Z?
Silent mode forces the CAN transmitter into the recessive state while the receiver remains fully active. Driving TXD low in the way the TJA1441 data sheet describes puts the driver in its high-impedance recessive state, so the node no longer contributes dominant bits or error frames to the bus but can still receive and report traffic. This is useful in listen-only diagnostic nodes, partially powered modules, and bench test setups where a connected node must not disturb an active bus.
Why does the TJA1441AT/0Z have a separate VIO pin?
The VIO pin powers only the digital logic side of the transceiver, covering TXD and RXD. Because VIO accepts 1.8 V to 5.5 V per the NXP TJA1441 data sheet, the same SOIC-8 device works with 5 V, 3.3 V, and low-voltage microcontrollers without a level shifter, while the transceiver core runs from the standard 5 V VCC rail. This is the key difference from the older TJA1051, which has no VIO pin and therefore ties TXD and RXD directly to the 5 V domain.
What is the difference between TJA1441AT/0Z and TJA1442AT/0Z?
Both are 5 Mbit/s CAN transceivers from NXP in the same SOIC-8 footprint, and the NXP TJA1441 data sheet states that the TJA1441 is intended as a simple replacement for existing high-speed Classical CAN and CAN FD transceivers. The functional differences between TJA1441 and TJA1442 relate to the internal standby and silent behaviour variants within the family, so confirm the exact mode behaviour and pin-level function of the variant you choose against the NXP data sheet for that part. Both are direct drop-in candidates for the same SOIC-8 footprint.
Can the TJA1441AT/0Z replace a TJA1051T/3?
Yes. The NXP TJA1441 data sheet explicitly states that the TJA1441 is intended as a simple replacement for high-speed Classical CAN and CAN FD transceivers such as the TJA1051 or TJA1057, and that it offers pin compatibility designed to avoid changes to hardware and software design. The practical caveat is the extra VIO pin on the TJA1441, which is a new connection on the SOIC-8 footprint and must be tied to a valid logic supply, so existing boards need that one added connection plus a decoupling capacitor.
Where can I download the TJA1441AT/0Z datasheet PDF?
The official NXP data sheet for this device is hosted at https://www.nxp.com/docs/en/data-sheet/TJA1441.pdf, and the same document is reachable from the NXP part page at https://www.nxp.com/part/TJA1441. It contains the pin description table, the SOIC-8 pin configuration drawing, the electrical characteristics table with VCC and VIO limits, the CAN bus timing and bit timing recommendations, and the layout guidance for the CANH and CANL traces.
Where can I find the TJA1441AT/0Z pinout?
The SOIC-8 pin configuration is given in the NXP TJA1441 data sheet, which identifies pin 1 as TXD, pin 2 as GND, pin 3 as VCC, pin 4 as RXD, pin 5 as GND, pin 6 as CANL, pin 7 as CANH, and pin 8 as VIO. The same pin names appear in the datasheet pin description table and in the application information section, which also shows the recommended external capacitors and bus termination arrangement.
What bus speeds can the TJA1441AT/0Z support?
The TJA1441AT/0Z supports data rates up to 5 Mbit/s, matching the high-speed CAN FD physical layer class of parts from NXP. The device also tolerates low-speed Classical CAN operation, which is what the NXP TJA1441 data sheet addresses when it describes the TJA1441 as a replacement for high-speed Classical CAN and CAN FD transceivers such as the TJA1051 and TJA1057. Actual bus length and bit timing limits depend on the transceiver loop delay and the cable used.
How should I terminate the CAN bus when using the TJA1441AT/0Z?
Terminate the CANH and CANL pair with a 120 ohm resistor at each end of the bus only, and leave intermediate nodes without termination. The NXP TJA1441 data sheet shows this arrangement in its application information, together with the split termination capacitor option for EMC-sensitive designs. Keeping the differential pair tightly coupled and away from slow, high-impedance stubs reduces reflections and improves signal integrity at 5 Mbit/s.
What are the key specifications of the TJA1441AT/0Z that engineers should know?
The TJA1441AT/0Z is a single-channel CAN transceiver rated to 5 Mbit/s, supplied in an 8-pin SOIC surface-mount package, with a 4.5 V to 5.5 V VCC supply and a 1.8 V to 5.5 V VIO logic supply. It adds a Silent mode for high-impedance transmitter operation with the receiver still active, and it operates over an extended -40 C to +125 C temperature range. It is offered in an automotive-ready SOIC-8 option code, and NXP lists the TJA1441 family as active.
Is the TJA1441AT/0Z suitable for automotive body control modules?
Yes, the TJA1441AT/0Z is suitable for automotive body and comfort domain networks where a CAN bus links ECUs over long harness runs. The device supports up to 5 Mbit/s, includes bus fault and short-circuit protection on the CAN driver stage, and operates across an extended -40 C to +125 C temperature range. The SOIC-8 format is also preferred over smaller packages in automotive designs because it eases hand soldering, inspection, and rework in field service.
What is the best NXP equivalent for the TJA1441AT/0Z?
The closest NXP equivalents in the same SOIC-8 footprint are the TJA1442AT/0Z and TJA1443AT/0Z, plus the older TJA1051T/3 and TJA1057T/3. The TJA1442AT/0Z is the most directly comparable part in the same family with the same 5 Mbit/s capability, and the TJA1057T/3 is a high-speed alternative from an earlier generation. The NXP TJA1441 data sheet names the TJA1051 and TJA1057 as parts the TJA1441 is designed to replace with pin compatibility.
What can replace the TJA1441AT/0Z in an existing design?
The TJA1442AT/0Z, TJA1443AT/0Z, TJA1057T/3 and TJA1051T/3 are drop-in candidates that share the SOIC-8 footprint with the TJA1441AT/0Z. The NXP TJA1441 data sheet explicitly frames the TJA1441 as a pin-compatible replacement for the TJA1051 and TJA1057, which makes the reverse substitution straightforward for existing boards. When moving to an older TJA105x part, note that it has no VIO pin, so the logic supply connection on that pin must be removed or tied appropriately.
Is the TJA1441AT/0Z the same as a TJA1057T/3?
No, they are not identical, although they occupy the same SOIC-8 footprint and cover the same high-speed CAN function. The TJA1441AT/0Z adds a VIO logic supply pin and a dedicated Silent mode, and supports 5 Mbit/s operation, while the TJA1057T/3 is an earlier-generation high-speed transceiver without the VIO pin. The NXP TJA1441 data sheet states that the TJA1441 is intended as a pin-compatible replacement for the TJA1057 so that existing hardware and software designs can be retrofitted.
How do I decide between the TJA1441AT/0Z and a switching-based CAN alternative?
Choose the TJA1441AT/0Z when the design is a straightforward ISO 11898-2 CAN node, the bus is a physical copper pair with 120 ohm end termination, and low EMC emission and simple firmware control matter more than cost per node. It removes the need for an external transceiver, offers a VIO pin for direct microcontroller hookup, and keeps the Silent mode feature for diagnostics. If your system uses a non-standard bus or needs a galvanic isolated link, a digital isolator plus separate bus-side transceiver is the better architecture.
Where can I buy the TJA1441AT/0Z and what is the lead time?
The TJA1441AT/0Z is listed as active by NXP and is carried by multiple authorized distributors, so it is a normally available, non-obsolete part. Use the Request a Quote form on this page for current pricing, stock position, minimum order quantity and confirmed lead time for the SOIC-8 order code. For production planning, confirm the delivery schedule against your build forecast, since distributor inventory for this transceiver moves with automotive and industrial program demand.

داتای سەرچاوەی ئەندازیاری بۆ TJA1441AT/0Z — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the TJA1441AT/0Z when you need a 5 Mbit/s CAN FD physical layer in an 8-pin SOIC footprint with a separately powered logic side for a 3.3 V or 1.8 V microcontroller, or when the node must listen to a live bus without disturbing it, where the Silent mode is genuinely useful in diagnostics and flashing scenarios. Choose the TJA1442AT/0Z when you want the same family and footprint but a different standby behaviour variant, and the TJA1443AT/0Z when low-power mode handling matters most. Choose the TJA1057T/3 or TJA1051T/3 when you are maintaining an older design at 1 Mbit/s and do not need VIO or Silent mode, but remember that adding the TJA1441 to such a board requires connecting the VIO pin and adding its decoupling capacitor. If your system needs galvanic isolation, choose an isolated CAN transceiver instead, because no pin-compatible substitute here provides isolation. In every case, confirm the mode behaviour and timing in the NXP data sheet for the exact part before releasing the design.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە TJA1442AT/0Z TJA1443AT/0Z TJA1057T/3 TJA1051T/3
Package SOIC-8 (8-SO) SOIC-8 (8-SO) - same SOIC-8 (8-SO) - same SOIC-8 (8-SO) - same SOIC-8 (8-SO) - same
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
Maximum Data Rate 5 Mbit/s 5 Mbit/s 5 Mbit/s 5 Mbit/s 1 Mbit/s (-80%)
Logic Supply Pin (VIO) Yes, 1.8 V to 5.5 V Yes Yes No No
Silent Mode Yes Yes Yes No No
Transmit / Receive Channels 1 TX / 1 RX 1 TX / 1 RX 1 TX / 1 RX 1 TX / 1 RX 1 TX / 1 RX
Operating Temperature -40 C to +125 C -40 C to +125 C -40 C to +125 C -40 C to +125 C -40 C to +85 C
Documented Replacement Role Named in the NXP TJA1441 data sheet as a pin-compatible replacement for the TJA1051 and TJA1057 Sibling part in the TJA144x family Sibling part in the TJA144x family Predecessor high-speed transceiver replaced by the TJA1441 Predecessor transceiver replaced by the TJA1441

جیاکەرەوە سەرەکییەکان

  • Dedicated Silent mode for listen-only operation (بەراورد بەTJA1057T/3)
  • 5 Mbit/s CAN FD class data rate versus legacy 1 Mbit/s parts (بەراورد بەTJA1051T/3)
  • Independent 1.8 V to 5.5 V VIO logic supply (بەراورد بەTJA1051T/3)
  • Directly documented as a drop-in for the TJA1051 and TJA1057 (بەراورد بەTJA1051T/3)

تێبینییەکانی دیزاین

Route CANH and CANL as a tightly coupled differential pair with a constant spacing of roughly 0.2 mm to 0.3 mm, referenced to a continuous ground plane, and keep both traces the same length. Avoid stubs, vias, and plane changes under the pair, and keep the pair away from switching nodes and inductors. The NXP TJA1441 data sheet application information stresses that a symmetric pair is what keeps radiated emissions low and reflections small at 5 Mbit/s, especially in an enclosure that also contains display or power-conversion circuitry.

Decouple the VCC pin directly with a 100 nF ceramic capacitor and place a bulk capacitor close to the device for the 5 V rail, then add a separate 100 nF capacitor from VIO to ground with the shortest possible ground return to the transceiver ground pins. Because VIO can sit at a different voltage from VCC, keeping the two decoupling networks separate prevents rail-to-rail coupling from injecting noise onto the RXD output. Connect the VIO pin even if the logic domain is also 5 V, since the older TJA105x devices do not have this pin at all.

Do not treat the Silent mode as a bus-disconnect. In Silent mode the transmitter is held recessive but the receiver stays active, so the node still participates electrically on the bus and can still be affected by bus faults. Another common error is adding 120 ohm termination at every node instead of only the two physical ends of the bus, which drops the effective bus impedance and impairs signal quality. Also verify the transceiver ground pins are tied to the same reference as the CAN controller ground, and confirm the logic levels on TXD and RXD match the VIO voltage you selected.

Keep the CAN connector and the transceiver close together so the unshielded portion of the harness is minimized, and place a common-mode choke or split-termination capacitor at the connector if emissions testing shows a problem. Split termination with a capacitor in series with the 120 ohm resistor helps in EMC-sensitive designs by keeping high-frequency noise from entering the bus, at the cost of slightly worse low-frequency signal integrity. Validate the chosen termination with an oscilloscope measurement of the CANH/CANL differential waveform before production.

Budget for the loop delay of the transceiver when setting the CAN bit timing sample point, because the total propagation delay from TXD to RXD limits the usable bit rate for a given oscillator tolerance and cable length. The NXP TJA1441 data sheet provides recommended bit timing values and explains how the delay depends on VIO and bus loading. When migrating a TJA1051 or TJA1057 design, re-check the sample point because the TJA1441 introduces additional low-power and silent-mode logic in the signal path.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

NXP lists the TJA1441 family as active. RoHS, REACH, AEC-Q100 and halogen-free declarations are confirmed on the NXP product page materials and must be checked against the current NXP declaration for the exact order code before release.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

TJA1441AT/0Z TJA1441AT/0Z datasheet TJA1441 datasheet pdf TJA1441 pinout NXP TJA1441AT/0Z TJA1441 equivalent TJA1441 drop-in replacement TJA1441 vs TJA1051 TJA1441 vs TJA1442 5 Mbit/s CAN FD transceiver SOIC-8 CAN transceiver with Silent mode TJA1441AT/0Z automotive CAN bus module TJA1441AT/0Z price TJA1441AT/0Z stock TJA1441 application circuit CAN bus termination

پێکهاتە و زاراوە پەیوەندیدارەکان

NXP Semiconductors TJA1441AT/0Z TJA1441 TJA1442AT/0Z TJA1443AT/0Z TJA1057T/3 TJA1051T/3 CAN transceiver CAN FD Classical CAN ISO 11898-2 physical layer interface interface IC Silent mode VIO logic supply SOIC-8 surface mount differential pair bus termination signal integrity loop delay bit timing automotive body control module industrial CAN gateway 5 Mbit/s
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ