NXP Semiconductors

TJA1443AT/0Z - 5 Mbit/s CAN FD Transceiver | NXP

MPN: TJA1443AT/0Z ✓ چالاک
VIO Vdss
MOQ: 1 |

TJA1443AT/0Z گشتی

NXP Semiconductors TJA1443AT/0Z is a high-speed CAN transceiver with Standby, Sleep and Listen Only modes, operating up to 5 Mbit/s in a 14-pin SOIC package. The device connects a CAN or CAN FD controller to a physical two-wire CAN bus and supports VIO, EN, STB and ERR control or status functions. It is positioned as a hardware-compatible successor to established high-speed CAN transceivers.

A CAN transceiver is an interface integrated circuit that translates logic-level controller signals into differential bus voltages and converts received bus states back into controller-compatible signals. CAN belongs to the broader hierarchy of network interfaces, data converters and interface ICs. Its two-wire physical layer allows multiple nodes to communicate over a shared bus while supporting arbitration, fault handling and standardized high-speed operation.

The TJA1443AT/0Z supports data rates up to 5 Mbit/s and includes Standby, Sleep and Listen Only operating modes. These modes allow a design to reduce activity when communication is not required while preserving a path for wake-up or bus monitoring. VIO provides a logic-side interface referenced to the selected digital supply, while EN, STB and ERR support local mode control and error-state monitoring.

According to the NXP TJA1443 datasheet, the device implements the CAN physical layer defined by ISO 11898-2:2016 and is compatible with the high-speed requirements associated with SAE J2284-1 through SAE J2284-5. The TJA144x family is intended to interoperate with established high-speed Classical CAN and CAN FD controllers, helping simplify upgrades to existing hardware and software platforms.

Typical uses include automotive and industrial CAN FD nodes, gateway modules, body and comfort controllers, diagnostic interfaces, sensor concentrators and embedded communications equipment. It is particularly appropriate when a compact surface-mount transceiver, selectable low-power modes and centralized bus-fault awareness are required. Board layout must preserve the differential CAN_H and CAN_L return path and provide suitable termination and common-mode protection for the target network.

For a new design, compare the device against the TJA1443ATK/0Z automotive-grade ordering option and confirmed alternatives such as TCAN1043A. Do not assume electrical or qualification equivalence from package similarity alone; verify supply voltage, mode-control polarity, transceiver delay, bus fault behavior and automotive qualification against the system requirements.

This page combines the manufacturer datasheet, product-page information, commercial sourcing guidance, package-level comparison and practical replacement criteria. It highlights the operating modes, standards context and PCB considerations engineers need when evaluating the TJA1443AT/0Z for a high-speed CAN or CAN FD physical layer.

جێگرەوەکانی جێگۆڕکێ بۆ TJA1443AT/0Z — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ TJA1443AT/0Z (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Product Type, Package, Lifecycle Status, Standby Control.

NXP Semiconductors
Package: SOIC-14
Standby Control: Yes (STBN)
NXP Semiconductors
Product Type: High-speed CAN transceiver with Silent mode
Package: SOIC-8 (8-SO), surface mount
Lifecycle Status: Active (per NXP product overview)
NXP Semiconductors
Product Type: High-speed CAN and CAN FD transceiver
Package: 14-terminal HVSON, approximately 3 mm x 4.5 mm
Lifecycle Status: Active

TJA1443ATK/0Z

✅ جێگرەوەی ڕاستەوخۆ
NXP Semiconductors
📦 SOIC-14
High-speed CAN and CAN FD transceiver · 5 Mbit/s · 4.5 V to 5.5 V · VIO · Classical CAN and CAN FD · Standby, Sleep, and Listen Only modes · Two-wire CAN bus · ISO 11898-2:2016

پەیوەندی بۆ نرخ

بینینی داتاشیت →

TJA1443T/1J

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 SOIC-14
Same TJA1443 family and 14-pin SOIC footprint at up to 5 Mbit/s; order-code temperature or qualification differences must be checked against the target requirements

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

TJA1443T/3

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 SOIC-14
Same TJA1443 family and 14-pin SOIC footprint at up to 5 Mbit/s; the order-code temperature or qualification variant must be verified before substitution

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

TJA1043T/3

✅ جێگرەوەی ڕاستەوخۆ
📦 SOIC-14
Uses the same 14-pin SOIC CAN-transceiver footprint and is identified as a predecessor whose hardware can be replaced by TJA1443; standby and error-function behavior still require circuit-level review

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

TCAN1043A

✅ جێگرەوەی ڕاستەوخۆ
📦 SOIC-14
Identified as pin-to-pin compatible with TJA1443 and the updated TJA1043/TCAN1043 family; data-rate and mode characteristics should be matched against the 5 Mbit/s TJA1443AT/0Z

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

TJA1443AT/0Z تایبەتمەندییەکان

Product Type High-speed CAN transceiver
Maximum Data Rate 5 Mbit/s
Supported Bus Classical CAN and CAN FD two-wire bus
Physical-Layer Standard ISO 11898-2:2016
Automotive Interface Compatibility SAE J2284-1 to SAE J2284-5
Operating Modes Standby, Sleep and Listen Only
Logic Supply Pin VIO
Enable Control EN
Standby Control STB
Error Output ERR
Bus Interface Signals CAN_H and CAN_L
دۆخی RoHS unknown

ڕێنمایی ڕێکخستنی پینی TJA1443AT/0Z standard

ڕێکخستنی پین بۆ TJA1443AT/0Z (پاکێجی standard). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی standard بۆ TJA1443AT/0Z

هیچ داتای وردی پینئاوت بەردەست نییە بۆ TJA1443AT/0Z.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

TJA1443AT/0Z گونجاوە بۆ 6 بەکارھێنانs: Automotive CAN FD Gateway, Industrial CAN FD Sensor Node, Vehicle Body Control Module, CAN FD Diagnostic Interface, Embedded Communications Controller, CAN FD Network Test Equipment.

🚗

Automotive CAN FD Gateway

The TJA1443AT/0Z fits a gateway that connects CAN FD-capable controllers to a physical two-wire vehicle network. Its documented 5 Mbit/s capability supports high-speed CAN FD communication, while Standby, Sleep and Listen Only modes provide options for normal operation, reduced activity and bus monitoring. The NXP datasheet identifies compatibility with ISO 11898-2:2016 and the SAE J2284 family, providing a useful basis for automotive interface design. PCB implementation should preserve a continuous CAN_H/CAN_L differential path, place termination away from the transceiver pins and provide the protection required by the vehicle network.

🏭

Industrial CAN FD Sensor Node

The TJA1443AT/0Z is suitable for industrial sensor nodes that must place CAN FD traffic on a shared two-wire bus while limiting unnecessary activity. At up to 5 Mbit/s, it supports high-rate communication, and its three documented modes allow the controller to select full operation, Standby, Sleep or Listen Only behavior. These states are useful in machinery, process monitoring and factory automation where a node may wake periodically or remain available to detect bus activity. The physical layer must be designed for the cable length, topology and common-mode range of the installation rather than relying only on nominal data rate.

🚙

Vehicle Body Control Module

A body control module can use the TJA1443AT/0Z to connect door, lighting, climate and other distributed controllers to a CAN FD-capable backbone. The 5 Mbit/s interface provides useful bandwidth for combined control and diagnostic traffic, while Listen Only mode can support diagnostic observation without driving the bus. The Standby and Sleep states offer additional control over system activity. Because body modules often operate across broad temperature and automotive transient conditions, engineers should confirm the exact order code's qualification and protection ratings, and should route CAN_H and CAN_L as a controlled differential pair with appropriate surge protection.

🔧

CAN FD Diagnostic Interface

The TJA1443AT/0Z can serve as the physical-layer element in a diagnostic interface that connects a host controller to a vehicle or industrial CAN FD network. Its up-to-5-Mbit/s capability supports diagnostic data transfer at the network rate, and Listen Only mode is useful when the node must monitor traffic without asserting a dominant state. Standby can be used during transitions between diagnostic sessions, while Sleep can reduce demand when the vehicle network is inactive. The interface circuit still requires a correctly designed termination strategy, bus fault protection and isolation boundary if the diagnostic equipment connects to a ground domain outside the target vehicle.

🧩

Embedded Communications Controller

The TJA1443AT/0Z is appropriate for embedded systems that already implement CAN framing in an MCU, FPGA or dedicated controller and need a standardized physical-layer interface. It converts the controller-side TXD and RXD signaling into the differential CAN bus and provides EN, STB and ERR functions for local control and status. The 5 Mbit/s maximum rate supports CAN FD-capable links, while VIO can align the digital interface with the controller's supply domain. Firmware must align its bit timing and fault handling with the transceiver's propagation characteristics, while PCB layout must minimize loop area between CAN_H and CAN_L.

📟

CAN FD Network Test Equipment

The TJA1443AT/0Z can be used in compact CAN FD test modules, protocol analyzers and communication demonstrators. Its 5 Mbit/s capability allows the instrument to participate in traffic on supported high-speed networks, and Standby, Sleep and Listen Only modes make it easier to build a non-intrusive monitoring function. VIO helps connect the transceiver to instruments operating from a selected logic supply. For laboratory equipment, include accessible test points, controlled termination and protection against accidental bus shorts. The interface should still be validated against the intended network's bit timing, cable length and fault-recovery behavior.

What is the TJA1443AT/0Z?
The TJA1443AT/0Z is an NXP Semiconductors high-speed CAN transceiver for Classical CAN and CAN FD physical-layer networks. It operates up to 5 Mbit/s and provides Standby, Sleep and Listen Only modes. According to the NXP TJA1443 datasheet, it interfaces a CAN controller with the physical two-wire bus through CAN_H and CAN_L.
What is the maximum data rate of TJA1443AT/0Z?
The TJA1443AT/0Z supports a maximum CAN data rate of 5 Mbit/s. NXP lists the device as a high-speed CAN transceiver with Standby, Sleep and Listen Only functionality. This speed makes it applicable to CAN FD systems whose arbitration and data phases remain compatible with the transceiver's physical-layer capability.
Where can I download the TJA1443AT/0Z datasheet PDF?
The official TJA1443 datasheet PDF is available from NXP at https://www.nxp.com/docs/en/data-sheet/TJA1443.pdf. It contains the general description, operating modes, electrical characteristics, pin information and application information for the TJA144x family. Use this manufacturer document as the controlling reference for layout and circuit decisions.
Where can I find the TJA1443AT/0Z pinout?
Use the pin-description table and package drawing in the NXP TJA1443 datasheet at https://www.nxp.com/docs/en/data-sheet/TJA1443.pdf to assign PCB tracks. The public product information identifies VIO, EN, STB and ERR connections but does not provide a complete numbered pin table, so consult the official package drawing before laying out the board.
What CAN standards does TJA1443AT/0Z support?
The TJA1443AT/0Z implements the CAN physical layer defined in ISO 11898-2:2016. According to the NXP TJA1443 datasheet, the TJA144x family is also associated with SAE J2284-1 through SAE J2284-5 high-speed interface requirements. These specifications define the physical signaling used by the transceiver, while the connected controller handles the CAN protocol.
What operating modes are available on TJA1443AT/0Z?
The TJA1443AT/0Z provides Standby, Sleep and Listen Only operating modes. These states provide control over normal communication and reduced-power or monitoring behavior. NXP describes the device as a high-speed CAN transceiver with these three modes; consult the mode-state table in the datasheet before assigning EN and STB logic levels.
Is TJA1443AT/0Z compatible with CAN FD controllers?
Yes, the TJA1443AT/0Z is intended for CAN FD physical-layer networks as well as Classical CAN systems. The NXP datasheet describes it as an interface between a CAN or CAN FD protocol controller and the physical two-wire bus. The controller and system timing remain responsible for protocol operation and arbitration.
Where can I buy TJA1443AT/0Z online?
Use the Request a Quote form on this page to request TJA1443AT/0Z availability, order quantity and lead time from XAIPART. The form supports direct sourcing without relying on an individual distributor listing. Confirm the exact TJA1443AT/0Z order code and package before placing an order.
What is the price of TJA1443AT/0Z?
Current TJA1443AT/0Z commercial terms are available through the Request a Quote form on this page. Submit the required quantity, target package and delivery details to obtain a current quotation. The structured price area should also be checked because distributor pricing and availability can change with quantity and market conditions.
What is the lead time for TJA1443AT/0Z?
Request the current lead time for TJA1443AT/0Z through the Request a Quote form on this page. Include your required quantity and expected delivery date so the order can be evaluated against current availability. NXP lists the TJA1443AT as active, but a project-specific lead time still requires a current quotation.
Is TJA1443AT/0Z in stock?
The TJA1443AT/0Z is listed as active by NXP, but live project-specific stock should be requested through the Request a Quote form on this page. Provide the quantity, package and destination required for your build. This avoids relying on an unverified inventory indication from an individual product listing.
What is the best drop-in replacement for TJA1443AT/0Z?
TCAN1043A is a cross-brand drop-in candidate because the available comparison identifies it as pin-to-pin compatible with TJA1443 and the updated TJA1043/TCAN1043 family. NXP also identifies TJA1443ATK/0Z as a closely related ordering option. Confirm package, supply voltage, mode behavior and qualification before approving either replacement.
What can replace TJA1443AT/0Z?
TJA1443ATK/0Z is the closest same-brand option identified in the comparison information, while TCAN1043A is a cross-brand candidate described as pin-to-pin compatible. The choice depends on the exact package, automotive qualification, operating-mode polarity and electrical limits. Use the manufacturer datasheets to validate every replacement rather than relying on the footprint alone.
TJA1443AT/0Z vs TCAN1043A - which is better for a CAN FD node?
Choose TJA1443AT/0Z when its NXP-specific mode set and known operating behavior match an existing NXP-based design; choose TCAN1043A when its electrical limits, qualification and availability better fit the new design. The available replacement information identifies TCAN1043A as pin-to-pin compatible, but package equivalence alone does not establish full functional equivalence.
When should I choose TJA1443AT/0Z over TCAN1043A?
Choose TJA1443AT/0Z when maintaining an NXP controller ecosystem, using its documented Standby, Sleep and Listen Only behavior, or avoiding a manufacturer change is more important than broader sourcing options. Choose TCAN1043A when its verified electrical characteristics, qualification and commercial position provide a stronger engineering fit. Pin compatibility still requires validation.
Is TJA1443AT/0Z suitable for automotive CAN FD applications?
TJA1443AT/0Z is a high-speed CAN transceiver intended for CAN and CAN FD systems, including automotive interface contexts addressed by SAE J2284. For an automotive production design, verify the exact order code's AEC-Q100 grade, temperature range, transient protection and automotive qualification in the official NXP documentation. The TJA1443ATK/0Z option is identified as automotive-grade in product information.
What are the key specifications of TJA1443AT/0Z that engineers should know?
The key documented specifications are a maximum rate of 5 Mbit/s, support for Classical CAN and CAN FD, ISO 11898-2:2016 physical-layer operation, and Standby, Sleep and Listen Only modes. The device also exposes VIO, EN, STB and ERR functions. Supply limits, temperature range, delay and protection ratings should be confirmed in the NXP datasheet.

داتای سەرچاوەی ئەندازیاری بۆ TJA1443AT/0Z — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose TJA1443AT/0Z when a compact NXP high-speed CAN transceiver is required with operation up to 5 Mbit/s and documented Standby, Sleep and Listen Only modes. It is particularly suitable for CAN FD-capable automotive or industrial nodes that benefit from an established NXP family and VIO, EN, STB and ERR functions. Select TJA1443ATK/0Z when the same family and footprint are needed with the documented AEC-Q100 Grade 0 automotive option. TJA1443T/1J and TJA1443T/3 may suit temperature or qualification requirements that match those order codes, but their exact limits must be checked. For a cross-brand replacement, TCAN1043A is the strongest documented candidate because it is identified as pin-to-pin compatible with TJA1443 and updated TJA1043/TCAN1043 devices. Before finalizing any substitution, verify supply voltage, timing, control polarity, fault recovery and automotive qualification rather than relying on package equality alone.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە TJA1443ATK/0Z TJA1443T/1J TJA1443T/3 TJA1043T/3 TCAN1043A
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors Texas Instruments
Package SOIC-14 SOIC-14 - same footprint SOIC-14 - same footprint SOIC-14 - same footprint SOIC-14 - same footprint SOIC-14 - same footprint
Product Type High-speed CAN transceiver High-speed CAN transceiver High-speed CAN transceiver High-speed CAN transceiver High-speed CAN transceiver with sleep mode High-speed CAN transceiver
Bus Interface CAN_H and CAN_L CAN_H and CAN_L CAN_H and CAN_L CAN_H and CAN_L CAN_H and CAN_L CAN_H and CAN_L

جیاکەرەوە سەرەکییەکان

  • Close same-family ordering option with documented automotive Grade 0 positioning (بەراورد بەTJA1443ATK/0Z)
  • Three explicitly documented operating modes (بەراورد بەTCAN1043A)
  • Controller-side voltage flexibility through VIO (بەراورد بەTJA1443T/1J)

تێبینییەکانی دیزاین

Route CAN_H and CAN_L as a tightly coupled differential pair with continuous reference to the same ground plane. Keep the pair length matched, minimize stubs and avoid routing it across splits in the ground plane. Place the transceiver close to the connector or protection network, and follow the package drawing and NXP application guidance for the shortest practical bus path.

Do not treat a common SOIC-14 footprint as proof that every alternate CAN transceiver is functionally interchangeable. Verify EN and STB polarity, RXD behavior, error reporting, VIO compatibility, propagation delay and Sleep wake-up behavior. The TJA1443 family is intended to replace established TJA1043-class hardware, but existing firmware and board connections must still be checked before substitution.

Keep power and ground connections short, place required decoupling capacitors at the associated device pins and provide a low-impedance ground path from the transceiver to the connector or protection components. Separate the CAN pair from high-speed switching nodes and sensitive analog inputs. If an isolated CAN interface is used, keep isolation-creepage and capacitance requirements in the component placement and bus routing plan.

CAN uses differential signaling, but poor pair geometry can still radiate or convert common-mode noise into data errors. Use symmetric termination according to the network topology, avoid unnecessary stubs and keep external protection components close to the connector. Evaluate EMC performance with the complete harness, chassis or enclosure configuration because cable routing materially affects radiated emissions.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The TJA1443ATK/0Z is identified as AEC-Q100 Grade 0 in product information. Exact compliance declarations for TJA1443AT/0Z were not confirmed.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

TJA1443AT/0Z datasheet TJA1443AT/0Z pinout TJA1443AT/0Z datasheet pdf TJA1443AT/0Z equivalent TJA1443AT/0Z replacement TJA1443AT/0Z cross reference TJA1443AT/0Z vs TCAN1043A TJA1443AT/0Z footprint TJA1443AT/0Z application circuit TJA1443AT/0Z price TJA1443AT/0Z stock NXP TJA1443AT/0Z

پێکهاتە و زاراوە پەیوەندیدارەکان

NXP Semiconductors TJA1443AT/0Z TJA1443ATK/0Z TJA1443T/1J TJA1443T/3 TJA1043T/3 TCAN1043A high-speed CAN transceiver CAN transceiver CAN FD Classical CAN Controller Area Network physical-layer interface interface IC network interface semiconductor two-wire CAN bus CAN_H CAN_L ISO 11898-2:2016 SAE J2284-1 SAE J2284-5 Standby mode Sleep mode Listen Only mode VIO EN STB ERR SOIC-14 surface-mount package
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ