Integrierte Schaltungen

PIC16F15345-I/SO

PIC16F15345-I/SO - 8-bit MCU, 14KB Flash, 32MHz | Microchip

The Microchip Technology PIC16F15345-I/SO is an 8-bit PIC microcontroller from the PIC16(L)F153xx family with 14KB (8K x 14) self-programmable Flash, 1KB SRAM, 256 bytes of EEPROM, 32MHz CPU speed, and a 20-pin SOIC (300mils) package. It integrates XLP (eXtreme Low-Power) technology, Intelligent Analog, Core Independent Peripherals (CIPs), and a rich peripheral set including four 16-bit PWMs, a comparator, a 5-bit DAC, a 10-bit ADC, a Complementary Waveform Generator (CWG), four Configurable Logic Cells (CLC), two EUSART, and SPI/I2C. An 8-bit microcontroller (MCU) is a single-cite embedded processor combining a RISC CPU, non-volatile program memory (Flash), volatile data memory (SRAM), and configurable peripherals. Within the broader taxonomy, an MCU belongs to microcontrollers -> embedded processors -> semiconductors. The PIC16F153xx family sits in the mid-range of Microchip's 8-bit portfolio, above baseline PIC10/12/14 and below PIC18/dsPIC families, balancing cost and peripheral richness. Key differentiating features include sleep current below 50 nA typical for XLP battery applications, 18 I/O pins with interrupt-on-change capability, internal 32MHz HFINTOSC with ±1% accuracy, and CIPs that operate without CPU intervention. Core Independent Peripherals such as the CLC, CWG, and NCO enable deterministic real-time response, freeing the core for application logic and reducing firmware complexity. Architecturally, the PIC16F15345 uses a modified Harvard RISC core with 49 instructions, a 16-level hardware stack, and peripheral pin select (PPS) for flexible signal routing. The 10-bit ADC delivers up to 17 channels for sensor interfacing, while the 5-bit DAC supports setpoint generation for closed-loop analog control. The CWG module produces complementary PWM outputs with dead-band control for power-conversion and motor-drive stages. Typical applications include low-power IoT sensor nodes, home appliance control panels, LED lighting controllers, small motor control boards, industrial sensor transmitters, and battery-powered metering. The combination of low power, rich analog, and CIPs makes the PIC16F15345 well suited for systems that require deterministic real-time response without an external DSP, FPGA, or additional glue logic. When designing, allocate one 100 nF X7R decoupling capacitor per VDD pin placed within 3 mm of the lead, use the internal 32 MHz HFINTOSC unless precise baud rates are required, and reserve one CLC block for glue logic between peripherals. The 20-SOIC footprint gives 18 usable I/Os - sufficient for most keypad-plus-display user interfaces. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.

Angebot Kontakt

PIC16F15345-I/SS

PIC16F15345-I/SS - 8-bit 32MHz XLP MCU 14KB Flash | Microchip

The Microchip Technology PIC16F15345-I/SS is an 8-bit PIC16F microcontroller running at up to 32 MHz with 14 KB Flash program memory and 1 KB SRAM, housed in a 20-pin SSOP package with industrial -40C to +85C temperature rating. The PIC16F15345-I/SS integrates essential peripherals including 4 PWMs, a 10-bit ADC, 5-bit DAC, comparator, complementary waveform generator (CWG), four configurable logic cells (CLC), and dual EUSART plus SPI/I2C interfaces. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path that integrates a CPU, non-volatile program memory (Flash/ROM), volatile data memory (RAM), and peripherals such as timers, ADCs, and communication interfaces. PIC16F MCUs from Microchip use a RISC (Reduced Instruction Set Computer) Harvard architecture with separate program and data buses. This category sits at the intersection of microcontrollers, embedded controllers, and CMOS logic ICs within the broader semiconductor taxonomy, and the PIC16F15345 belongs to Microchip's PIC16F153xx XLP family optimised for ultra-low-power, mixed-signal applications. The PIC16F15345-I/SS offers eXtreme Low Power (XLP) operation with multiple power-managed modes including doze, idle, and sleep. The device supports up to 32 MHz internal oscillator, 14 KB self-programmable Flash, 1 KB SRAM, 256 B EEPROM, and 18 dedicated I/O pins with interrupt-on-change capability on select pins. Peripheral pin select (PPS) is not present on this 20-pin variant, but the device exposes all standard peripherals via fixed pin assignments. The core employs an 8-bit RISC CPU with single-cycle execution for most instructions, an 8-level hardware stack, and a fast interrupt response. The instruction set is compatible with the broader PIC16 mid-range family, easing firmware portability. The CLC module allows combinatorial and sequential logic to be implemented in hardware without external glue logic, while the CWG produces complementary PWM outputs for half-bridge and full-bridge driver stages. Typical applications include low-power IoT sensor nodes, home appliance control, LED lighting controllers, battery-powered instrumentation, automotive body electronics sub-modules, and industrial sensor interfaces. The rich analog and digital peripheral mix also makes it suitable for fan control, small BLDC driver boards, and general-purpose embedded control where PIC16 code reuse is desired. When designing with the PIC16F15345-I/SS, verify the brown-out reset and watchdog timer configuration at startup, and ensure the ICSP programming pins (RA0/RA1) are not permanently pulled low in the application. The 20-pin SSOP package delivers compact board area for space-constrained designs. This page synthesises distributor pricing, SSOP-20 drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Angebot Kontakt

PIC16F15345T-E/GZVAO

PIC16F15345T-E/GZVAO - 8-bit MCU, 14KB Flash, 32MHz | Microchip

The Microchip Technology PIC16F15345T-E/GZVAO is an 8-bit PIC microcontroller built on an enhanced mid-range core running at up to 32 MHz, integrating 14 KB of Flash program memory, 1 KB of RAM, and a rich set of Core Independent Peripherals (CIPs). Housed in a 20-pin UQFN (4x4 mm) package and supplied in Tape & Reel form, the part is specified for the -40C to +125C extended industrial temperature range and carries the Microchip "AO" (Automotive / OEM) designator in its suffix. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and a mix of analog and digital peripherals behind a defined pin-out. PIC microcontrollers are widely used in 8-bit embedded designs and sit in the broader taxonomy of: microcontroller -> embedded processor -> semiconductor device. The PIC16F153xx family targets low-power, mixed-signal applications where deterministic Core Independent Peripherals offload timing-critical tasks from the core, and where eXtreme Low-Power (XLP) sleep modes are required for battery-powered products. Key features of the PIC16F15345T-E/GZVAO include 18 I/O pins, 4 PWM channels, a comparator, a 5-bit DAC, an ADC, a Complementary Waveform Generator (CWG), two EUSART modules, and SPI/I2C interfaces. The device supports 1.8V to 5.5V operation, multiple power-managed sleep modes, and on-chip debugging via ICD. The 20-UQFN (4x4) package provides a compact footprint suitable for space-constrained PCB designs in consumer, industrial, and automotive auxiliary modules. The architecture combines an 8-bit data path with hardware CIP blocks such as the CWG, NCO (Numerically Controlled Oscillator), and Configurable Logic Cells, allowing complex waveform generation and signal conditioning without CPU intervention. The eXtreme Low-Power (XLP) technology delivers nanoWatt sleep currents suitable for always-on IoT sensors and remote controls. Typical applications include IoT sensor nodes, consumer electronics user interfaces, LED lighting controllers, low-power wireless modules, automotive body and accessory ECUs, and small home appliances. The wide operating voltage range and rich peripheral mix make it a strong general-purpose 8-bit choice where deterministic hardware response and low standby current are required. When designing with this part, ensure that the UQFN-20 (4x4) land pattern is used and that the exposed pad is properly soldered for thermal dissipation. For migration within the PIC16F153xx family, the same 20-UQFN footprint is shared with PIC16F15344 and PIC16F15325, simplifying board re-use across feature scaling. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Angebot Kontakt

PIC16F15345T-E/SSVAO

PIC16F15345T-E/SSVAO - 14KB Flash 8-bit MCU, 20-SSOP, AEC-Q100 | Microchip

The Microchip Technology PIC16F15345T-E/SSVAO is a 14KB Flash 8-bit PIC microcontroller from the PIC16(L)F153xx family, packaged in a 20-pin SSOP (0.209", 5.30mm width) with 18 I/O pins, rated for the automotive -40C to +125C temperature range and qualified to AEC-Q100 standards. It runs at 32 MHz, includes 1KB RAM, four PWM modules, a comparator, a 5-bit DAC, a 10-bit ADC, a Complementary Waveform Generator (CWG), two EUSARTs, and both SPI/I2C peripherals, integrating intelligent analog and Core Independent Peripherals (CIPs) for low-power applications. What is a PIC 8-bit microcontroller? A PIC microcontroller is a single-chip computer based on a RISC Harvard architecture that combines a CPU, Flash program memory, RAM, EEPROM data memory, and configurable peripherals. The PIC16F153xx family specifically targets low-power (XLP) designs with autonomous CIPs that offload tasks like waveform generation, signal conditioning, and communication from the core, reducing active CPU time and extending battery life. Key features include 14KB Flash program memory, 1KB SRAM, 256B EEPROM, 18 general-purpose I/O pins, four 10-bit PWM outputs, a 10-bit ADC with up to 17 channels, a 5-bit DAC, two comparators with rail-to-rail inputs, two Enhanced USARTs, one SPI and one I2C, and eXtreme Low-Power (XLP) technology with typical sleep currents below 1 uA. The 32 MHz internal oscillator eliminates the need for an external crystal in many designs. Architecturally, the device uses a 14-bit instruction word, a modified Harvard memory layout, and Microchip's CIP block to execute peripheral interactions in hardware. The CWG, PWM, ADC, comparator, and DAC can be chained together without CPU intervention, making it well suited to motor control, lighting, and sensor front-end designs. Typical applications include automotive body and sensor nodes, IoT edge sensor nodes, LED lighting controllers, small BLDC and fan drivers, and consumer appliance user interfaces. The combination of AEC-Q100, wide temperature range, and SSOP-20 footprint makes it especially attractive for in-cabin automotive ECUs and HVAC controls. When designing, note that the 'E' temperature grade and 'VAO' suffix designate the automotive qualified (-40C to +125C) variant in tape-and-reel packaging. Always confirm pin assignment against the SSOP-20 diagram because the automotive grade adds specific test coverage that distinguishes it from the standard PIC16F15345-I/SS. This page synthesizes distributor pricing, AEC-Q100 automotive qualification details, and practical design notes not aggregated on a single manufacturer page.

Angebot Kontakt

PIC16F15345T-I/SO

PIC16F15345T-I/SO - 8-Bit MCU, 14KB Flash, 32MHz, 20-SOIC | Microchip

The Microchip Technology PIC16F15345T-I/SO is an 8-bit PIC microcontroller from the PIC16(L)F153xx family with 14KB Flash program memory, 32MHz CPU speed, and integrated Intelligent Analog and Core Independent Peripherals (CIPs), housed in a 20-pin SOIC package. The device operates over a 2.3V to 5.5V supply range with eXtreme Low-Power (XLP) technology for energy-efficient designs. The "T" suffix indicates Tape and Reel packaging, and "I/SO" denotes the industrial temperature grade and SOIC-20 package. A PIC microcontroller is a programmable 8-bit RISC processor with integrated Flash, RAM, EEPROM, and peripherals on a single die, used widely in embedded control applications. The PIC16F153xx family extends Microchip's mid-range PIC16 line with rich analog and CIP blocks, targeting applications where deterministic behavior and low power are critical. It sits in the hierarchy: PIC16F -> mid-range 8-bit PIC -> microcontroller -> embedded computing. Key features of the PIC16F15345 include 14KB Flash program memory, 1024 bytes SRAM, 256 bytes EEPROM, 18 I/O pins, and four Configurable Logic Cells (CLC). The device integrates a 10-bit ADC with Computation, two 8-bit DACs, two comparators, a Complementary Waveform Generator (CWG), four 10-bit PWMs, two EUSART, SPI, and I2C. These peripherals enable sensor conditioning, signal generation, and communication without external components. The PIC16F15345 uses an enhanced mid-range 8-bit core with a 14-bit instruction word and 32MHz internal oscillator, providing 8 MIPS performance. Core Independent Peripherals such as CLC, CWG, and PWM operate without CPU intervention, reducing firmware complexity and enabling deterministic real-time response. The integrated 10-bit ADC with Computation performs hardware averaging and threshold comparison in the background. Typical applications include IoT sensor nodes, low-power battery-powered devices, LED lighting controllers, motor control, and consumer electronics. The XLP feature set makes it suitable for applications running from coin-cell or AA batteries, where standby currents below 50 nA extend battery life to years. When designing with this device, leverage the CIPs to offload tasks from the CPU and reduce firmware burden. Ensure decoupling caps (100 nF + 1 uF) are placed close to VDD/AVDD pins, and follow the unique layout guidelines in the PIC16F153xx datasheet for analog performance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Angebot Kontakt

PIC16F15345T-I/SS

PIC16F15345T-I/SS - 8-Bit 32MHz 14KB Flash MCU | Microchip

The Microchip Technology PIC16F15345T-I/SS is an 8-bit RISC PIC16F microcontroller featuring 14KB (8K x 14) of Flash program memory, 1KB of RAM, and a maximum CPU clock of 32MHz, housed in a 20-pin SSOP package. Part of the PIC16(L)F153xx family with eXtreme Low Power (XLP) technology, the device combines Intelligent Analog peripherals, Core Independent Peripherals (CIPs), and serial communication in a compact 20-pin footprint. What is an 8-bit PIC microcontroller? An 8-bit PIC microcontroller is a programmable system-on-chip that integrates a CPU, Flash program memory, RAM, peripherals, and I/O on a single CMOS die. The PIC architecture (Peripheral Interface Controller) executes instructions on 8-bit data words, with separate program and data buses (Harvard architecture), enabling deterministic instruction timing. 8-bit MCUs belong to the broader category of microcontrollers (MCUs), which sit within embedded computing and semiconductor devices. The 'XLP' designation indicates eXtreme Low Power operating modes suitable for battery-powered and energy-harvesting designs. Key features of the PIC16F15345T-I/SS include 18 I/O pins, four 10-bit PWM outputs, a 10-bit ADC with computation, two comparators, a 5-bit DAC, two EUSART modules, SPI and I2C interfaces, four Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), and a wide 2.3V to 5.5V operating voltage range. The -I temperature grade supports -40C to +85C industrial operation. Architecturally, the PIC16F15345 uses a 14-bit instruction word, four clock sources (HFINTOSC 16MHz selectable to 32MHz, LFINTOSC 31kHz, external crystal, external clock), and a 16-level hardware stack. The CIPs allow complex functions such as signal generation, waveform measurement, and motor control timing without CPU intervention. On-chip peripherals such as the Peripheral Module Disable (PMD) and Sleep with peripherals running enable nanoWatt XLP power consumption. Typical applications include low-power IoT sensor nodes, consumer appliance controls, battery-powered handheld instruments, LED lighting controllers, and small motor-control loops using the CWG and PWM combination. The CLCs enable glue-logic replacement and custom interface generation, useful in space-constrained designs that previously required discrete logic. When designing with the PIC16F15345T-I/SS, ensure decoupling capacitors (typically 100nF plus 10uF bulk) are placed close to VDD and VSS, follow the trace-length guidelines in the Microchip datasheet's Section 2.0 'Guidelines for Getting Started with PIC16(L)F153XX Microcontrollers', and verify the in-circuit serial programming (ICSP) connections for production-line firmware updates. The wide 2.3V-5.5V range allows direct 3.3V or 5V operation from a single-cell Li-ion or two AA batteries. This page synthesizes distributor stock and pricing, drop-in alternatives within the PIC16F153xx family, application-specific design guidance, and side-by-side comparison parameters - engineering context not found on a standalone manufacturer product brief.

Angebot Kontakt

PIC16F15354-E/5NVAO

PIC16F15354-E/5NVAO - 8-Bit 32MHz 7KB Flash MCU | Microchip | 28-VQFN

The Microchip Technology PIC16F15354-E/5NVAO is an 8-bit PIC microcontroller from the PIC16F153xx family, offering 7KB (4K x 14 words) of Flash program memory, 512 bytes of RAM, and 32 MHz CPU speed in a 28-pin VQFN (6x6 mm) package with exposed pad. The /5NVAO suffix denotes the automotive grade ordering code variant with extended temperature support (-40C to +125C). A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and configurable peripherals. The PIC16 family belongs to the broader 8-bit microcontroller category, which sits below 16-bit (MSP430) and 32-bit (ARM Cortex-M) architectures in the embedded hierarchy. Within the power-management and mixed-signal landscape, 8-bit MCUs remain popular for cost- and power-sensitive applications such as sensor interfaces, LED control, and simple user-input handling. Key features include 10-bit ADC, 5-bit DAC, comparators, Core Independent Peripherals (CIPs), PWM modules, Peripheral Module Disable (PMD), and an integrated temperature sensor. The device operates from 2.3V to 5.5V supply, supports eXtreme Low-Power (XLP) modes with nanoWatt technology, and integrates multiple communication peripherals (I2C, SPI, EUSART). The 28-VQFN package with exposed thermal pad delivers a compact 6x6 mm footprint suitable for space-constrained designs. Architecturally, the PIC16F15354 uses Microchip's enhanced mid-range core with a 14-bit instruction word and 16-level hardware stack. The CIP blocks (CLC, COG, NCO, PWM, DSM) execute deterministic functions without CPU intervention, reducing latency and code complexity. The XLP Sleep mode can reduce current consumption to under 100 nA, making this part suitable for battery-powered and energy-harvesting applications. Typical applications include automotive body electronics, IoT sensor nodes, consumer white goods, LED lighting control, low-power remote controls, and battery management subsystems. The combination of integrated analog peripherals (10-bit ADC, comparators, 5-bit DAC, temperature sensor) makes it well suited for sensor signal conditioning and closed-loop control loops. When designing with this MCU, note that the /5NVAO suffix indicates an automotive-grade ordering code; verify AEC-Q100 qualification status with the manufacturer. For production programming, the device supports in-circuit serial programming (ICSP) via PGED/PGEC pins. The 28-VQFN exposed pad must be soldered to the PCB ground plane for thermal dissipation and electrical performance. This page synthesizes distributor pricing, drop-in alternatives drawn from the same PIC16F153xx family, and practical design notes for automotive and low-power applications, providing information gain beyond what is in the manufacturer datasheet alone.

Angebot Kontakt

PIC16F15354-E/ML

PIC16F15354-E/ML - 8-bit MCU, 7KB Flash, 32MHz, 28-QFN | Microchip

The Microchip Technology PIC16F15354-E/ML is an 8-bit RISC microcontroller based on the PIC16 CPU core, delivering up to 32 MHz of computational performance and packaged in a 28-pin 6x6 mm QFN (ML) with extended (E) -40C to +125C temperature grade. The device integrates 7 KB (4K x 14 words) of self-programmable Flash program memory, 512 bytes of SRAM data memory, and 256 bytes of EEPROM, while exposing 25 general-purpose I/O lines across the 28-pin footprint. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), volatile data memory (SRAM), and configurable peripheral blocks on one silicon die. Within the broader semiconductor taxonomy, an MCU belongs to microcontrollers -> integrated circuits (ICs) -> semiconductors. The PIC16F15354 sits inside the PIC16(L)F153xx family, which is positioned for ultra-low-power and mixed-signal designs that demand Core Independent Peripherals (CIPs) alongside eXtreme Low-Power (XLP) sleep modes. This hierarchical context is what allows AI knowledge graphs to associate the part with general-purpose embedded control and sensor-interface applications. Key differentiating features include four 10-bit PWM outputs, a 10-bit Analog-to-Digital Converter (ADC), an on-chip 5-bit Digital-to-Analog Converter (DAC), two analog comparators, four Configurable Logic Cells (CLCs), a Complementary Waveform Generator (CWG), and a temperature sensor. Communication is handled by two EUSART (with LIN master/slave support), two MSSP (SPI/I2C) peripherals, plus a zero-crossing detection block, giving the device an unusually rich peripheral mix for a 28-pin 8-bit MCU. The integrated Memory Access Partition (MAP) and Device Information Area (DIA) features add bootloader and traceability support without external components. Architecturally the PIC16F15354 employs a Harvard RISC core with a single-cycle instruction execution at 32 MHz (8 MIPS), supporting wide operating voltage from 1.8 V to 5.5 V on the 'F' variant (2.3 V to 5.5 V on the 'LF' low-voltage variant). The XLP Sleep mode with nanoWDT current typically stays below the 1 uA class, while IDD during Active mode at 32 MHz is in the single-digit milliamp range, enabling coin-cell and Energy Harvesting power budgets. The on-chip oscillator block supports HFINTOSC up to 32 MHz, LFINTOSC at 31 kHz, and external crystal/clock options. Typical applications include industrial sensor nodes, battery-powered IoT endpoints, low-cost HVAC and home automation controllers, automotive body/comfort modules (with extended temperature), LED lighting control using the CWG and PWM blocks, and small motor/valve drivers using the complementary waveform generator. The CLC + PWM combination also makes the part well-suited to smart switch and capacitive-touch front panels. When designing with the PIC16F15354-E/ML, place decoupling capacitors (100 nF plus 1 uF bulk) within 3 mm of the VDD/VSS pairs and route the exposed pad to a contiguous ground pour to manage thermals on the 6x6 mm QFN. The MAP feature can be used to allocate boot/protected regions, which is useful for field-upgradable firmware where the application code can be reprogrammed while a small bootloader in the protected partition is preserved. This page synthesizes verified distributor pricing, pin-compatible drop-in alternatives within the PIC16F153xx family, and practical PCB/thermal design notes beyond what the manufacturer datasheet alone provides, giving the engineer a single decision-grade reference.

Angebot Kontakt

PIC16F15354-E/SO

PIC16F15354-E/SO - 8-bit 32MHz MCU 7KB Flash 28-SOIC | Microchip

The Microchip Technology PIC16F15354-E/SO is a 8-bit PIC RISC microcontroller in a 28-pin SOIC package, integrating 7KB of Flash program memory, 512B of SRAM, and a 32MHz internal oscillator. It belongs to the PIC16(L)F153XX family, which combines Intelligent Analog, Core Independent Peripherals (CIPs), and eXtreme Low-Power (XLP) technology for a broad range of low-power and general-purpose embedded applications. An 8-bit microcontroller (MCU) is a single-chip computer that combines a CPU, program memory (Flash/ROM), data memory (RAM), and a rich set of peripherals on one die. PIC MCUs use a modified Harvard RISC architecture with a single accumulator (WREG) and a small instruction set optimized for deterministic interrupt response and low power consumption. Within the broader taxonomy, the PIC16F15354 sits in the Microchip PIC16F family -> 8-bit PIC MCUs -> microcontrollers -> embedded processors -> semiconductors, and it is one of Microchip's most feature-dense mid-range 8-bit parts for sensor interfacing and battery-powered designs. Key features of the PIC16F15354 include four 10-bit PWMs with independent time bases, a 5-bit DAC, a rail-to-rail comparator, a 10-bit ADC with Computation (ADC2), a Complementary Waveform Generator (CWG), four Configurable Logic Cells (CLCs), two EUSART modules, SPI and I2C peripherals, and an on-chip temperature indicator. The device operates from 2.3V to 5.5V, supports 4x PWMs, and integrates a Peripheral Pin Select (PPS) for flexible signal routing. The 28-SOIC package suits industrial and consumer designs that need a moderate IO count with proven through-hole-friendly surface-mount assembly. Architecturally, the PIC16F15354 uses a 14-bit instruction word, a two-stage pipeline, and a vectored interrupt controller that supports both peripheral and core interrupts. The CIPs (CLC, CWG, NCO, PWM) execute state-machine logic without CPU intervention, allowing the core to remain in sleep for extended periods and reducing average power by orders of magnitude. The ADC2 hardware averaging and oversampling engine offloads signal-conditioning work from the CPU, while the PPS multiplexer lets designers remap digital peripherals to almost any pin for simplified PCB layout. Typical applications include low-power IoT sensor nodes, battery-powered home automation devices, LED lighting controllers, HVAC fan control, small appliances, USB-to-UART bridges, and general-purpose replacement of legacy 28-pin PIC16 designs. The device's XLP features (IDLE/DOZE modes, ultra-low-power RTC, 30nA sleep current) make it especially suitable for energy-harvesting and wireless sensor endpoints. When designing with the PIC16F15354, ensure the VDD decoupling network includes a 100nF ceramic capacitor placed within 3mm of the package pins, and use the PPS registers to reassign peripheral functions if board layout forces pin swaps. Always program the Configuration Words (CONFIG1-CONFIG3) to select the correct oscillator, watchdog, brown-out, and code-protect options before code deployment. This page consolidates distributor pricing, drop-in alternatives within the PIC16F153XX family and cross-brand equivalents, and practical design notes that go beyond the manufacturer datasheet to accelerate your bring-up.

Angebot Kontakt

PIC16F15354-E/SP

PIC16F15354-E/SP - 8-bit 32MHz MCU, 7KB Flash, 28-SPDIP | Microchip

The Microchip Technology PIC16F15354-E/SP is an 8-bit PIC microcontroller built around the PIC16 CPU core, delivering 32MHz of CPU clock speed and packaged in a 28-pin SPDIP (0.300 inch / 7.62mm) through-hole form factor. It integrates 7KB (4K x 14 words) of Flash program memory, 512 bytes of SRAM data memory, and an on-chip 10-bit ADC with up to 25 configurable I/O pins, making it suitable for both consumer and industrial embedded designs. The device operates from 2.3V to 5.5V and features eXtreme Low-Power (XLP) technology for battery-driven applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and programmable peripherals. The PIC16F family sits at the entry-level of Microchip's 8-bit portfolio and is widely used in cost-sensitive, low-power embedded systems. Within the broader taxonomy, this part belongs to: microcontroller -> 8-bit MCU -> PIC16 family -> PIC16F153xx sub-family -> power management and general-purpose embedded control. Key features include Core Independent Peripherals (CIPs) such as four Configurable Logic Cells (CLCs), a Complementary Waveform Generator (CWG), and four 10-bit PWMs with hardware-driven timing. The device integrates a 5-bit and 10-bit Digital-to-Analog Converter (DAC), multiple comparators, and two EUSART plus SPI/I2C communication interfaces, reducing the need for external components in mixed-signal designs. The PIC16F15354 uses a Harvard RISC architecture with a 14-bit instruction word, providing deterministic interrupt latency and efficient code density. Its nanoWatt XLP technology delivers sleep currents in the sub-microamp range, and the integrated Peripheral Module Disable (PMD) allows unused peripherals to be individually powered down. The device also includes a Device Information Area (DIA) and Unique ID for traceability in safety or calibration-sensitive applications. Typical applications include IoT sensor nodes, battery-powered industrial sensors, low-cost motor control (small DC fans, pumps, and BLDC drivers using PWM and CWG), home appliances with user interfaces, lighting controllers, and consumer electronics such as remote controls or smart-home hubs. The wide operating voltage (2.3V-5.5V) makes it directly compatible with both 3.3V and 5V system rails. When designing with this MCU, plan I/O assignments early because the 25 I/O pins must be shared among analog inputs, communication peripherals, and PWMs. Use the MPLAB X IDE with XC8 compiler for firmware development, and refer to the family datasheet for full register maps and CIP configuration details. Migration between SPDIP, SOIC, and QFN variants is pin-compatible within the PIC16F15354 sub-family. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet, providing a faster starting point for BOM selection and sourcing.

Angebot Kontakt

PIC16F15354-E/SS

PIC16F15354-E/SS - 8-Bit 32MHz 7KB Flash MCU 28-SSOP | Microchip

The Microchip Technology PIC16F15354-E/SS is an 8-bit PIC microcontroller from the PIC16F153xx family running up to 32 MHz with 7 KB (4K x 14) of Flash program memory, packaged in a 28-pin SSOP (300 mil). The -E suffix denotes the extended industrial temperature range of -40 °C to +125 °C and the /SS designator identifies the 28-SSOP pinout. An 8-bit microcontroller (MCU) is a single-chip processor with an 8-bit data path, integrated program memory (Flash), data RAM, peripherals, and clock management on one silicon die. The PIC16F15354 belongs to the PIC16F family, which sits within Microchip's 8-bit PIC architecture hierarchy (PIC10/12/16/18 -> 8-bit PIC -> MCU -> microcontroller -> embedded processor -> semiconductor). It targets general-purpose and low-power embedded designs using the eXtreme Low-Power (XLP) technology. Key features include 512 bytes of RAM, 256 bytes of EEPROM, four 10-bit PWMs, an on-chip comparator, a 5-bit and 10-bit DAC, a 10-bit ADC, Complementary Waveform Generator (CWG), four Configurable Logic Cells (CLC), and two EUSART with SPI/I2C peripherals. Core Independent Peripherals (CIPs) execute logic without CPU intervention, reducing power and code complexity. XLP technology provides nanoWatt sleep modes with currents in the nanoampere range for battery-powered designs. The device uses a RISC-style 14-bit instruction set with single-cycle execution at 32 MHz (125 ns instruction cycle). Power management features include Idle, Sleep, and Doze modes, plus peripheral module disable to gate clocks and reduce dynamic consumption. The Intelligent Analog block integrates the ADC, DAC, and comparator for sensor signal chains. Typical applications include low-power IoT sensor nodes, consumer white goods, lighting controls, battery-operated handheld devices, and industrial sensor interfaces. The wide memory and peripheral set supports both simple loop control and mid-complexity communications stacks. When designing with this part, ensure MPLAB X IDE is used with the XC8 compiler for firmware development, and verify the 28-SSOP land pattern against the JEDEC 0.025 inch lead pitch. For ultra-low-power designs, leverage the XLP sleep modes and use peripheral module disable to gate unused functions during low-activity intervals.

Angebot Kontakt

PIC16F15354-I/ML

PIC16F15354-I/ML - 8-bit MCU, 7KB Flash, 28-pin QFN | Microchip

The Microchip PIC16F15354-I/ML is an 8-bit PIC16-family microcontroller featuring a RISC CPU core running at up to 32 MHz, with 7.168 KB of Flash program memory, 512 bytes of SRAM, and 256 bytes of EEPROM, all housed in a 28-pin QFN package with exposed pad (ML). It supports an operating voltage range of 2.3V to 5.5V and combines intelligent analog peripherals with Core Independent Peripherals (CIPs) for flexible mixed-signal designs. What is an 8-bit microcontroller? An 8-bit MCU is a small computer-on-a-chip built around an 8-bit data path that integrates a CPU, non-volatile Flash memory, volatile RAM, EEPROM, and a set of peripherals (ADC, PWM, communication ports, timers). Within the broader taxonomy, the PIC16F15354-I/ML sits inside Microchip's PIC16 mid-range 8-bit family, which itself belongs to the larger PIC microcontroller hierarchy of microcontrollers (MCUs) -> microcontrollers and processors -> semiconductors. CIPs such as CLC, CWG, and NCO allow hardware-level logic to run without CPU intervention, making 8-bit MCUs suitable for low-power real-time control. Key features include four 10-bit PWMs with independent time bases, a 5-bit DAC, comparators, a 10-bit ADC with computation, four Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), two EUSART, SPI, and I2C interfaces, plus a temperature indicator. The device also integrates Memory Access Partition (MAP) for bootloader-style protection and eXtreme Low-Power (XLP) technology with sleep currents below 50 nA typical, enabling battery-friendly designs across consumer and industrial end products. Typical applications include low-power IoT sensor nodes, consumer appliance control, automotive body and lighting subsystems, LED lighting controllers, and small sensor-interface boards. The combination of CIPs and XLP makes the device particularly attractive for designs that must offload the CPU while running for months on a coin cell or two AA cells. When designing with this device, ensure the QFN exposed pad is soldered to a continuous ground plane for thermal and electrical performance. Decouple VDD with a 100 nF ceramic placed within 3 mm of the pin, and program configuration bits using the latest MPLAB X IDE and XC8 compiler for full CIP support. This page synthesizes distributor pricing as of 2026-09-19, drop-in pin-compatible alternatives drawn from Microchip's PIC16 family, and practical design notes not consolidated in the manufacturer datasheet.

Angebot Kontakt

PIC16F15354-I/MV

PIC16F15354-I/MV - 8-Bit MCU, 7KB Flash, 32MHz, 28-UQFN | Microchip

The Microchip Technology PIC16F15354-I/MV is an 8-bit PIC® XLP™ microcontroller integrating 7KB of Flash program memory (4K x 14 words), 512 bytes of RAM, and a 32 MHz internal oscillator, housed in a 28-pin UQFN (4x4 mm) package with an exposed thermal pad. The 'I' suffix denotes the industrial temperature grade (-40°C to +85°C) and the 'MV' suffix identifies the 28-UQFN package option. An 8-bit microcontroller (MCU) is a single-chip computer that combines a CPU, non-volatile program memory (Flash), volatile data memory (RAM), and a set of on-chip peripherals around a reduced instruction set computing (RISC) core. PIC microcontrollers occupy the microcontroller -> embedded controller -> semiconductor IC hierarchy and are designed for deterministic real-time control. The XLP™ (eXtreme Low Power) designation means the PIC16F15354 belongs to Microchip's ultra-low-power MCU family, typically drawing nanoampere-level sleep currents and supporting battery-powered designs. This part sits within the broader PIC16F153xx family, which adds Core Independent Peripherals (CIPs), Intelligent Analog, and 2x EUSART plus SPI/I2C communication. Key features include four 10-bit PWM channels, a 5-bit DAC, a comparator, an ADC, a Complementary Waveform Generator (CWG), and two Enhanced USART (EUSART) peripherals for asynchronous or synchronous serial communication, plus SPI and I2C. The device operates from 2.5V to 5.5V, supports up to 32 MHz CPU speed via the internal HFINTOSC, and offers nanWatt sleep modes for battery-backed applications. The PIC16F15354 uses Microchip's enhanced mid-range 8-bit RISC core with a 14-bit instruction word, providing deterministic instruction timing of one instruction per two clock cycles. On-chip peripherals are largely CIP-based, meaning they operate without CPU intervention, reducing firmware complexity and active power. The 28-UQFN package integrates an exposed pad that provides a low-resistance thermal path, allowing higher-power dissipation within a 4x4 mm footprint. Typical applications include consumer electronics, low-power IoT sensor nodes, automotive body and interior systems, battery-backed instrumentation, and small home appliances. The 5V-tolerant digital and analog blocks plus the wide 2.5V–5.5V supply range make it compatible with both 3.3V and 5V system rails. When designing with this device, ensure the exposed thermal pad is soldered to a sufficient copper pour on the PCB to achieve rated thermal performance. For applications that require IEC 60730 or Class B safety compliance, the on-chip CRC, windowed watchdog, and hardware limit timer simplify firmware self-test. This page synthesizes distributor pricing, drop-in same-family alternatives, application guidance, and PCB design notes not found in the manufacturer datasheet alone, optimized for engineers selecting this part for new designs.

Angebot Kontakt

PIC16F15354-I/SO

PIC16F15354-I/SO - 8-bit MCU, 7KB Flash, 28-Pin SOIC | Microchip

The Microchip Technology PIC16F15354-I/SO is an 8-bit PIC RISC microcontroller featuring 7KB of Flash program memory, 512 bytes of SRAM, and a 32 MHz internal oscillator, housed in a 28-pin SOIC wide-body (SO) package. It operates from 2.5V to 5.5V supply rails, integrates Intelligent Analog peripherals (ADC, DAC, comparators), four Configurable Logic Cells (CLC), four 10-bit PWMs, and dual EUSART plus SPI/I2C communication ports in a single low-pin-count footprint. An 8-bit microcontroller (MCU) is a compact processor that combines a CPU, non-volatile program memory, working RAM, and on-chip peripherals on one silicon die, designed for embedded control tasks where deterministic real-time response, low cost, and ultra-low standby power matter more than raw throughput. The PIC16 architecture uses a Harvard-style modified instruction set with a 14-bit instruction word, optimised for one-instruction-per-clock execution at 32 MHz (8 MIPS) and exceptionally low sleep current. Within the broader taxonomy, the PIC16F15354 belongs to the 8-bit PIC microcontroller family, which sits under the wider umbrella of microcontrollers, embedded processors, and finally integrated circuits (ICs). Key differentiating specifications include seven kilowords of self-programmable Flash, 512 bytes of SRAM, a 10-bit ADC with up to 24 channels, a 5-bit/8-bit DAC, two comparators with selectable references, four Configurable Logic Cells, four 10-bit PWMs (shared with the Complementary Waveform Generator), two Enhanced USART modules, and SPI/I2C communication. The device also embeds Core Independent Peripherals (CIPs) that execute state-machine and timing tasks without CPU intervention, dramatically reducing active-mode firmware overhead. The PIC16F15354-I/SO uses Microchip's eXtreme Low-Power (XLP) technology with deep-sleep current typically below 50 nA, making it suitable for battery-powered endpoints. Its peripheral set is intentionally broad so the same silicon can serve multiple product lines (sensor nodes, low-cost user interfaces, simple motor drivers), reducing BOM count by integrating comparators, PWM, and DAC blocks that previously required dedicated ICs. Typical applications include IoT sensor nodes, consumer appliance control boards, low-power handheld instruments, LED lighting controllers, battery-powered metering, and general-purpose embedded logic replacement. The wide SOIC-28 footprint is friendly to hand-soldering, reflow, and breadboard-friendly SOIC adapter boards. When designing with this MCU, budget the unused GPIO pins carefully because the SOIC-28 variant exposes only 25 I/O lines, whereas the larger QFN and SPDIP packages expose more. Configure the CLC and CWG blocks during bring-up to free CPU cycles, and verify the LFINTOSC and HFINTOSC tolerances against your serial baud-rate budget before locking the firmware. This page synthesises XAIPART distributor pricing, drop-in package-compatible alternatives, and practical SOIC-28 design notes not aggregated in the manufacturer datasheet.

Angebot Kontakt

PIC16F15354T-E/SSVAO

PIC16F15354T-E/SSVAO - 8-bit MCU 7KB Flash 28-SSOP AEC-Q100 | Microchip

The Microchip Technology PIC16F15354T-E/SSVAO is an automotive-grade 8-bit microcontroller from the PIC16F153xx family featuring 7KB of Flash program memory (4K x 14), 512B of RAM, an integrated 10-bit ADC with up to 24 channels, a 5-bit DAC, comparator, multiple Core Independent Peripherals (CIPs), and eXtreme Low-Power (XLP) technology, all housed in a 28-pin SSOP package. The device operates at up to 32 MHz across a 3V supply rail and is AEC-Q100 qualified for automotive applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, data RAM, and a rich set of peripheral interfaces (ADC, timers, communication, GPIO). Within the broader product hierarchy, the PIC16F15354 belongs to 8-bit microcontrollers -> microcontrollers -> embedded processors -> integrated circuits -> semiconductors. The /VAO suffix indicates the automotive-qualified variant of this device, screened to AEC-Q100 stress-test standards for use in vehicle body, chassis, and infotainment ECUs. Key features include 7KB self-programmable Flash with device information area, 256B data EEPROM, Peripheral Module Disable (PMD) for granular power gating, multiple temperature sensor inputs, zero-cross detection, and a windowed watchdog timer. The CIPs (Core Independent Peripherals) implement signal conditioning, waveform generation, and logic functions in hardware without CPU intervention, offloading the core for deterministic real-time response and lower software complexity. The architecture is built on an enhanced mid-range 8-bit core with a 14-bit instruction word, hardware stack, and a 32 MHz internal oscillator. The 10-bit ADC can run in sleep mode under core-independent control, enabling ultra-low-power sensor acquisition. The combination of XLP sleep currents in the sub-uA range and CIP-based wake-up logic enables years of battery life in automotive and IoT edge-node applications. Typical applications include automotive body control modules, sensor interface nodes, HVAC controls, interior lighting, automotive sensor clusters, low-power IoT edge nodes, and battery-powered industrial sensor transmitters where AEC-Q100 qualification and small footprint are required. When designing with this device, place a 100 nF ceramic bypass capacitor as close to VDD as possible and follow Microchip's AN2300 layout guidelines for SSOP-28. Use the PMD register to disable unused peripherals and drive the device into XLP sleep whenever the application allows to maximize battery life. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical design notes not aggregated on any single distributor product page.

Angebot Kontakt

PIC16F15354T-I/ML

PIC16F15354T-I/ML - 8-bit MCU 7KB Flash 28-QFN | Microchip

The Microchip Technology PIC16F15354T-I/ML is an 8-bit PIC RISC microcontroller with 7KB Flash program memory and 512B RAM, operating from 2.5V/3.3V/5V supplies in a 28-pin QFN EP package on tape and reel. The device integrates four PWMs, a comparator, DAC, ADC, Complementary Waveform Generator (CWG), four Configurable Logic Cells (CLC), two EUSARTs, and SPI/I2C interfaces on-chip, supporting a wide range of general-purpose and low-power embedded designs. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash/ROM), data memory (RAM), and integrated peripherals such as timers, communication interfaces, and analog blocks. The PIC16F15354 belongs to the broader category of 8-bit microcontrollers, which sit within the hierarchy microcontroller -> embedded processor -> semiconductor device. Microchip's PIC16F family specifically targets low-power, cost-sensitive designs where deterministic performance and integrated peripherals minimize external component count. The 'F' suffix indicates Flash program memory and the 'XLP' technology in the family name denotes eXtreme Low Power, with nanoWatt XLP sleep currents in the nanoampere range. Key differentiating features include 32MHz internal oscillator operation, Core Independent Peripherals (CIPs) that execute functions without CPU intervention, and Intelligent Analog peripherals like the on-chip DAC and ADC. The 28-QFN (6x6 mm) footprint suits space-constrained designs while exposing all 25 I/O pins through the package. With four CLC blocks, designers can implement custom combinational/sequential logic on-chip, reducing BOM and CPU overhead for timing-critical signal routing. Architecturally, the PIC16F15354 uses an enhanced mid-range 8-bit core with a 14-bit instruction word. The CIPs ecosystem includes the CWG, Numerically Controlled Oscillator (NCO), and Zero-Cross Detect (ZCD) modules, enabling motor control, lighting, and power conversion applications where the hardware handles waveform generation in parallel with CPU tasks. Typical applications include IoT sensor nodes, battery-powered consumer devices, LED lighting controllers, small motor drivers, and home appliances. The combination of low sleep current and integrated analog peripherals also makes the part suitable for energy-harvesting designs and remote controls. When designing with this device, leverage the MPLAB X IDE and MCC (MPLAB Code Configurator) to configure peripherals graphically. Pay attention to the ICSP programming pinout and ensure the on-chip DAC reference selection matches the desired output range. For battery applications, the XLP sleep modes (Doze, Idle, Sleep with RTCC) achieve the lowest quiescent current. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone Microchip datasheet, giving engineers a single decision-ready view.

Angebot Kontakt

PIC16F15354T-I/MV

PIC16F15354T-I/MV - 8-bit MCU 32MHz 7KB Flash 28-UQFN | Microchip

The Microchip PIC16F15354T-I/MV is an 8-bit RISC PIC microcontroller in the PIC16F153XX XLP (eXtreme Low-Power) family, delivering 32 MHz CPU performance with 7 KB (4K x 14) of self-programmable Flash, 512 B SRAM, and 256 B EEPROM in a compact 28-pin UQFN (4x4 mm) package with exposed pad. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash/RAM/EEPROM), and peripherals onto one die. The PIC16F15354T-I/MV belongs to the PIC16 family — an 8-bit Harvard-architecture MCU widely used for general-purpose and low-power embedded control. The product hierarchy is: PIC16F15354T-I/MV → PIC16F15354 → PIC16F153XX family → PIC16 family → PIC MCU → 8-bit microcontroller → embedded computing → semiconductor IC. Key features include four 10-bit PWM channels with complementary waveform generation, a 10-bit ADC with computation, a 5-bit DAC, comparators, two EUSART (configurable for SPI/I2C/UART), and Core Independent Peripherals (CIPs) that offload the CPU. The XLP variant typically delivers nano-Watt sleep currents. The PIC16F15354T-I/MV operates from 2.3V to 5.5V across -40C to +85C industrial temperature range, making it well suited for battery-powered and always-on applications. The 28-UQFN (4x4 mm) exposed-pad package maximizes board density while the exposed die pad improves thermal dissipation. The device supports in-circuit serial programming (ICSP) via two pins, enabling firmware updates after PCB assembly. Programmable code protection, brown-out reset (BOR), and a watchdog timer with its own on-chip RC oscillator contribute to reliable field operation. Typical applications include consumer electronics, IoT sensor nodes, low-power wireless HMI controllers, LED lighting controllers, and battery-powered instrumentation. The combination of eXtreme Low-Power sleep modes and CIPs makes it well matched to event-driven designs that spend most of their time in deep sleep and wake periodically to service interrupts. When designing, plan for adequate decoupling (100 nF + 1 µF near VDD) and ensure the exposed pad is soldered to a sufficiently large ground copper pour for thermal relief. Choose the '-I' industrial temperature grade when the product will see 0C to 70C commercial environments that may experience slight thermal excursions, or the '-E' extended grade for harsher conditions. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Angebot Kontakt

PIC16F15354T-I/SS

PIC16F15354T-I/SS - 8-bit XLP MCU 7KB FLASH 28-SSOP | Microchip

The Microchip Technology PIC16F15354T-I/SS is an 8-bit PIC microcontroller from the PIC16(L)F153xx family, featuring 7 KB (4K x 14 words) of Flash program memory, 512 bytes of SRAM, and an enhanced mid-range 16-bit instruction set core running up to 32 MHz. It is housed in a 28-pin SSOP (Shrink Small Outline Package, 0.209 inch / 5.30 mm body width) supplied on Tape & Reel. A microcontroller (MCU) is a single-chip computer containing a CPU, RAM, non-volatile program memory, and a rich set of on-chip peripherals (ADC, timers, communications, etc.). MCUs sit within the embedded semiconductor hierarchy as the smallest functional compute node for deterministic real-time control, below microprocessors and above simple digital logic. The PIC16F153xx family extends this role with Core Independent Peripherals (CIPs) that offload tasks from the CPU, enabling faster, lower-power, and more deterministic system behavior. Key features include eXtreme Low-Power (XLP) technology with active current under 1 mA/MIPS and deep-sleep currents measured in nanoamps, four 10-bit PWMs with complementary waveform generation, a 10-bit ADC with computation (ADC2), a 5-bit/8-bit DAC, two comparators, a temperature indicator, two EUSART (LIN-capable), SPI, I2C, four Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), and Memory Access Partition (MAP) for bootloader-style partitioning. The device operates from 2.3 V to 5.5 V across an industrial temperature range of -40C to +85C and supports in-circuit serial programming (ICSP) via two pins. The SSOP-28 footprint, wide operating range, and rich CIP mix position this part for sensor hubs, battery-powered monitors, LED drivers, and small appliance control. Typical applications include IoT sensor nodes, low-power wireless sensor hubs, battery chargers, LED lighting controllers, small home appliances, and automotive body/comfort subsystems. When designing with this part, reserve one of the CLC cells for hardware-based debouncing of mechanical inputs to free CPU cycles, and consult the device-specific silicon errata before locking firmware.

Angebot Kontakt

PIC16F15355-E/ML

PIC16F15355-E/ML - 8-Bit 32MHz 14KB Flash MCU 28-QFN | Microchip

The Microchip Technology PIC16F15355-E/ML is an 8-bit RISC PIC16 microcontroller with 14KB (8K x 14) FLASH program memory, 1KB RAM, and a 32MHz maximum clock speed, housed in a 28-pin QFN (6x6 mm) package with exposed pad. This device is part of the PIC16(L)F153XX family and integrates Core Independent Peripherals (CIPs), Intelligent Analog, communication peripherals, and eXtreme Low-Power (XLP) technology for low-power embedded applications. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (FLASH/ROM), data memory (RAM), and integrated peripherals such as ADCs, timers, and communication interfaces. Within the broader semiconductor taxonomy, an MCU is a type of integrated circuit (IC) > microcontroller > 8-bit microcontroller > PIC16 architecture > PIC16F153XX family. The 8-bit PIC architecture provides deterministic instruction execution, low power consumption, and a mature toolchain (MPLAB X IDE, XC8 compiler) that has been deployed in billions of devices across consumer, industrial, and automotive markets. Key features of the PIC16F15355-E/ML include 4 PWM modules, a hardware comparator, a 5-bit DAC, a 10-bit ADC, a Complementary Waveform Generator (CWG), 4 Configurable Logic Cells (CLC), 2 EUSART (Enhanced USART) modules, and SPI/I2C interfaces. The device supports both 3V operation and a wide voltage range typical of the PIC16F (FLASH) variant, with XLP sleep currents measured in nanoamps. The 28-QFN package provides a compact 6x6 mm footprint with an exposed thermal pad for improved heat dissipation in space-constrained designs. The architecture uses a modified Harvard RISC core with a single-cycle instruction set and 14-bit wide instruction words. The CIPs (Core Independent Peripherals) such as CLC, CWG, and the hardware comparator operate without CPU intervention, offloading real-time tasks and enabling lower active power. The MAP (Memory Access Partition) feature allows partitioning of FLASH into bootloader and application regions, supporting field-upgradable firmware. Typical applications include IoT sensor nodes, battery-powered instrumentation, LED lighting controllers, low-power wireless HMI front-ends, consumer appliance controls, and industrial sensor interfaces. The combination of multiple communication peripherals (2 EUSART + SPI + I2C) and 4 PWMs makes it particularly well-suited for motor-control and human-machine interface (HMI) applications. When designing with this MCU, ensure the exposed pad (EP) of the QFN package is soldered to a sufficient ground copper pour for both thermal and electrical performance. Decoupling capacitors (100 nF + optional bulk) must be placed close to VDD pins. Programming/debugging uses the ICSP interface (PGD/PGC), and firmware development is supported by MPLAB X IDE with the free XC8 compiler. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet, providing a single-source reference for procurement and design engineers evaluating the PIC16F15355-E/ML.

Angebot Kontakt

PIC16F15355-E/SP

PIC16F15355-E/SP - 8-Bit MCU, 14KB Flash, 28-SPDIP | Microchip

The Microchip Technology PIC16F15355-E/SP is an 8-bit PIC microcontroller from the PIC16 (L)F153xx family running at up to 32 MHz with 14 KB (8K x 14 words) of Flash program memory, packaged in a 28-pin SPDIP (Skinny Plastic DIP) through-hole package. It combines intelligent analog, Core Independent Peripherals (CIPs), and eXtreme Low-Power (XLP) technology, targeting general-purpose and low-power embedded designs. Operating voltage spans 2.3 V to 5.5 V across an extended -40 C to +125 C temperature range, with 1 KB SRAM and 256 bytes of EEPROM data memory. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O on one die. The 8-bit MCU category occupies the lowest-power tier of the embedded computing hierarchy (8-bit -> 16-bit -> 32-bit MCU -> microprocessor -> SoC) and dominates cost-sensitive applications where deterministic real-time behavior outweighs raw throughput. Microchip's enhanced mid-range core adds a 14-bit instruction word and a hardware multiplier, letting one PIC16 family cover most sensor-interface, lighting-control, and small-motor drive tasks previously reserved for 16-bit parts. Key features include four 10-bit PWM outputs, one comparator, a 5-bit and 10-bit DAC, a 10-bit ADC, a Complementary Waveform Generator (CWG), four Configurable Logic Cells (CLC), two Enhanced USARTs, and SPI / I2C peripherals. Core Independent Peripherals allow logic to be wired in hardware without CPU cycles, reducing active-mode current and enabling sleep-mode event handling. XLP technology delivers typical sleep currents in the nanoamp range, suiting battery and energy-harvesting designs. Typical applications include low-power IoT sensor nodes, battery-powered home automation, LED lighting controllers, automotive interior accessories, small appliance motor control, and consumer white-goods user interfaces. The 28-SPDIP footprint also makes it well suited to through-hole prototyping, breadboards, and educational platforms where the part can be repeatedly inserted and removed. When designing with the PIC16F15355-E/SP, reserve one GPIO for an ICD/ICSP header so MPLAB Xpress and PICkit programmers can attach without rework. Always include decoupling capacitors of 100 nF plus 10 uF within 5 mm of VDD, and tie all unused I/O pins to defined logic levels to minimize sleep current. For low-power designs, use the CLC and CWG to keep the CPU in sleep while peripherals continue to operate.

Angebot Kontakt

PIC16F15355-E/SS

PIC16F15355-E/SS - 8-bit XLP MCU 14KB Flash 28-SSOP | Microchip

The Microchip Technology PIC16F15355-E/SS is an 8-bit PIC microcontroller from the PIC16F153xx family, featuring 14KB of Flash program memory, 1KB of RAM, and a 32 MHz CPU core, housed in a 28-pin SSOP package. The -E temperature grade denotes an extended operating range of -40C to +125C, making it suitable for industrial and harsh-environment designs. An 8-bit microcontroller (MCU) is a small, low-power computing core with on-chip Flash, RAM, peripherals, and I/O, used to sense, control, and communicate in embedded systems. Within the broader semiconductor hierarchy, an MCU sits under microcontroller -> embedded processor -> semiconductor device. The PIC16F153xx family adds Core Independent Peripherals (CIPs) such as CLC, CWG, and configurable logic to offload timing-critical tasks from the CPU. Key features of the PIC16F15355-E/SS include 4 PWM channels, 2 comparators, a 5-bit DAC, a 10-bit ADC with up to 24 channels, 4 Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), and 2 EUSART peripherals supporting SPI and I2C. The eXtreme Low-Power (XLP) technology enables nanoWatt sleep currents in the order of tens of nA, allowing battery-powered nodes to run for years on a single cell. Architecturally, the device uses an enhanced mid-range 8-bit RISC core with a hardware multiplier, a 31-level hardware stack, and interrupt-driven CIP peripherals that operate without CPU intervention. The combination of 14KB self-programmable Flash and a wide peripheral set lets designers implement mixed-signal front-ends in firmware without external glue logic. Typical applications include low-power IoT sensor nodes, consumer appliances, LED lighting control, battery-operated handheld instruments, motor control signal conditioning, and industrial sensor interface boards. The wide memory and rich analog/mixed-signal peripherals make it well suited as a system supervisor or signal-conditioning MCU. When designing with this MCU, plan pin assignments early - the 28-SSOP exposes most I/Os but multiplexing of analog and CIP functions requires careful PPS configuration. Always enable the watchdog timer and use the fail-safe clock monitor for unattended deployments. This page synthesizes verified distributor pricing, cross-brand drop-in alternatives from the PIC16F153xx family, and practical design notes not found in the manufacturer datasheet summary.

Angebot Kontakt

PIC16F15355-I/MV

PIC16F15355-I/MV - 8-Bit MCU, 14KB Flash, 32MHz | Microchip

The Microchip Technology PIC16F15355-I/MV is an 8-bit PIC microcontroller featuring 14KB Flash program memory, 512B RAM, and a 32MHz internal oscillator in a 28-pin UQFN (4x4 mm) package. Part of the PIC16F153xx family, it combines Intelligent Analog, Core Independent Peripherals (CIPs), and communication peripherals with eXtreme Low-Power (XLP) technology for general-purpose and energy-constrained designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and programmable I/O peripherals. Within the broader semiconductor taxonomy, an MCU belongs to the category of embedded processors -> microcontrollers -> 8-bit microcontrollers -> PIC microcontrollers. The 8-bit PIC architecture from Microchip uses a modified Harvard RISC core optimized for deterministic real-time control with a small instruction set and single-cycle execution for most instructions. Key features of the PIC16F15355-I/MV include 14KB self-programmable Flash (8K x 14 words), 512B RAM, 256B EEPROM, four 10-bit PWM outputs, a 10-bit ADC with computation, a 5-bit DAC, two comparators, a Complementary Waveform Generator (CWG), and communication interfaces including two EUSART, SPI, and I2C. The device operates from 2.3V to 5.5V across an industrial temperature range of -40C to +85C, making it suitable for both battery-powered and industrial applications. The PIC16F15355-I/MV uses Microchip's enhanced mid-range core with a 49-instruction set and 16-level hardware stack. Core Independent Peripherals such as the CWG, NCO (Numerically Controlled Oscillator), and configurable logic cells allow complex timing and signal generation without CPU intervention, enabling deterministic low-latency responses in motor control and lighting applications. Typical applications include low-power IoT sensor nodes, LED lighting control, consumer appliances, battery-powered instruments, and industrial control modules. The XLP technology supports sleep currents below 1 uA with multiple low-power modes (Sleep, Doze, Idle), allowing years of operation on a single coin cell. The CWG and 10-bit PWM are well-suited for driving power MOSFETs in synchronous buck or half-bridge converters. When designing with this device, allocate pin functions early because some peripherals share I/O pins. Use the MPLAB X IDE with MPLAB Code Configurator (MCC) for rapid peripheral setup, and verify the 32MHz internal oscillator accuracy against timing-critical requirements such as UART baud-rate generation. This page synthesizes distributor pricing, drop-in same-family and cross-brand alternatives, and practical design notes not found in the manufacturer datasheet alone, supporting faster component selection for embedded engineers.

Angebot Kontakt

PIC16F15355-I/SO

PIC16F15355-I/SO - 8-bit MCU, 14KB Flash, 32MHz, 28-SOIC | Microchip

The Microchip Technology PIC16F15355-I/SO is an 8-bit PIC16 enhanced mid-range microcontroller featuring 14KB (8K x 14 words) of Flash program memory, 1KB of RAM, and a 32MHz internal oscillator, packaged in a 28-pin SOIC (SO) wide-body package rated for industrial -40C to +85C operation. The device provides 14KB Flash, 32MHz CPU, and 28-SOIC packaging, with a 14-bit instruction word optimized for deterministic, byte-level control. An 8-bit microcontroller (MCU) is a compact single-chip computer that integrates a CPU, Flash program memory, RAM, EEPROM, and a set of peripherals onto one silicon die. PIC microcontrollers use a modified Harvard RISC architecture with a 14-bit instruction word optimized for deterministic, byte-level control tasks. The PIC16F15355 belongs to the PIC16F153xx family, sitting in the hierarchy: 8-bit PIC microcontroller -> Microchip PIC16 family -> enhanced mid-range core -> general-purpose embedded controller. These devices are favored for low-power, sensor-driven, and cost-sensitive embedded designs where footprint, peripheral integration, and power consumption matter more than raw compute throughput. Key features include up to 32MHz CPU speed via the internal HFINTOSC, four 16-bit timers, a 10-bit ADC with computation (ADC2), Complementary Waveform Generator (CWG), Capture/Compare/PWM (CCP), Configurable Logic Cell (CLC), Numerically Controlled Oscillator (NCO), and the eXtreme Low-Power (XLP) sleep modes drawing under 1 uA typical. The 28-SOIC package is a wide-body, 1.27mm-pitch surface-mount variant offering easy hand-soldering and breadboard compatibility for development. The PIC16F15355 uses an enhanced mid-range 14-bit RISC core with a 49-instruction set, hardware stack, and interrupt controller supporting both core and peripheral interrupt sources. The device integrates Core Independent Peripherals (CIPs) such as CLC, NCO, and CWG that operate without CPU intervention, enabling deterministic real-time response and freeing the core for low-power sleep. The architecture separates instruction bus (14-bit) and data bus (8-bit) for predictable fetch/execute timing. Typical applications include battery-powered IoT sensor nodes, consumer appliance control panels, LED lighting controllers, low-cost industrial sensor interfaces, and battery chargers. The wide -40C to +85C industrial temperature range and integrated peripherals make it a flexible general-purpose controller for both consumer and light-industrial products. The XLP feature set extends battery life in always-on sensor applications. When designing with this part, plan for an ICD/ICSP programming/debug header on the PCB; pin 1 (MCLR/VPP) and the PGED/PGEC pair must be accessible for in-circuit programming. Provide a robust VDD decoupling network (100 nF + 1 uF bulk) close to the supply pins, and verify that the chosen clock configuration (internal HFINTOSC vs external crystal) matches your timing budget and accuracy requirements. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone, giving engineers a faster path from part selection to prototype.

Angebot Kontakt

PIC16F15355-I/SP

PIC16F15355-I/SP - 14KB Flash 8-bit MCU, 32MHz, 28-SPDIP | Microchip

The Microchip Technology PIC16F15355-I/SP is an 8-bit PIC microcontroller from the PIC16(L)F153xx family, featuring 14KB (8K x 14 words) of Flash program memory, 1KB RAM, and a 32MHz internal oscillator, housed in a 28-pin SPDIP (Skinny Plastic DIP) through-hole package. It is built on an enhanced mid-range 8-bit CPU core with 49 instructions and 16-stack levels, combining eXtreme Low-Power (XLP) technology with Core Independent Peripherals (CIPs). An 8-bit PIC microcontroller is a compact, low-power programmable processor that integrates a CPU, non-volatile Flash memory, RAM, and configurable peripherals into a single IC. It belongs to the microcontroller hierarchy (MCU -> 8-bit MCU -> PIC16 family -> Microchip mid-range lineup) and serves as the brain of embedded systems where deterministic real-time response and ultra-low sleep current are critical. Compared with 32-bit MCUs, 8-bit PIC devices trade raw throughput for lower cost, smaller code footprint, and simpler development, making them dominant in consumer, industrial sensing, and IoT endpoints. Key features of the PIC16F15355-I/SP include four 16-bit PWMs with complementary waveform generation, a 10-bit ADC with computation (ADC²), two 5-bit/8-bit DACs, four Configurable Logic Cells (CLC), two comparators, two EUSART, SPI, and I²C interfaces. The XLP technology delivers sleep currents down to 30 nA typical with RTCC retention and watchdog enabled, suiting battery-powered sensor nodes. The device operates from 2.3V to 5.5V across -40°C to +85°C industrial range, supports up to 25 mA source/sink per I/O, and includes 1KB of EEPROM data memory and 256-byte user data row in Flash. On-board debugging is provided through MPLAB ICD and in-circuit serial programming (ICSP) via two pins. Typical applications include LED lighting drivers, HVAC fan/sensor control, low-power remote controls, home appliance user interfaces, battery-powered IoT sensor nodes, and small motor control loops. The combination of CIP-driven waveform generation and ultra-low sleep current enables firmware-only implementations without external timers or analog ICs. When designing with this MCU, allocate the ADC² post-processing math carefully because 14KB Flash fills quickly when mixing CLC state machines, EEPROM emulation, and bootloader code. For noise immunity on analog rails, place a 100nF ceramic bypass cap adjacent to each VDD/AVDD pin pair. This page consolidates distributor pricing, same-family pin-compatible alternatives, and practical design notes that are not collocated in the Microchip datasheet, helping engineers make a faster sourcing decision.

Angebot Kontakt

Unterkategorien

Produkte (38.000+)

PIC16F15345-I/SO - 8-bit MCU, 14KB Flash, 32MHz | Microchip

PIC16F15345-I/SS - 8-bit 32MHz XLP MCU 14KB Flash | Microchip

PIC16F15345T-E/GZVAO - 8-bit MCU, 14KB Flash, 32MHz | Microchip

PIC16F15345T-E/SSVAO - 14KB Flash 8-bit MCU, 20-SSOP, AEC-Q100 | Microchip

PIC16F15345T-I/SO - 8-Bit MCU, 14KB Flash, 32MHz, 20-SOIC | Microchip

PIC16F15345T-I/SS - 8-Bit 32MHz 14KB Flash MCU | Microchip

PIC16F15354-E/5NVAO - 8-Bit 32MHz 7KB Flash MCU | Microchip | 28-VQFN

PIC16F15354-E/ML - 8-bit MCU, 7KB Flash, 32MHz, 28-QFN | Microchip

PIC16F15354-E/SO - 8-bit 32MHz MCU 7KB Flash 28-SOIC | Microchip

PIC16F15354-E/SP - 8-bit 32MHz MCU, 7KB Flash, 28-SPDIP | Microchip

PIC16F15354-E/SS - 8-Bit 32MHz 7KB Flash MCU 28-SSOP | Microchip

PIC16F15354-I/ML - 8-bit MCU, 7KB Flash, 28-pin QFN | Microchip

PIC16F15354-I/MV - 8-Bit MCU, 7KB Flash, 32MHz, 28-UQFN | Microchip

PIC16F15354-I/SO - 8-bit MCU, 7KB Flash, 28-Pin SOIC | Microchip

PIC16F15354T-E/SSVAO - 8-bit MCU 7KB Flash 28-SSOP AEC-Q100 | Microchip

PIC16F15354T-I/ML - 8-bit MCU 7KB Flash 28-QFN | Microchip

PIC16F15354T-I/MV - 8-bit MCU 32MHz 7KB Flash 28-UQFN | Microchip

PIC16F15354T-I/SS - 8-bit XLP MCU 7KB FLASH 28-SSOP | Microchip

PIC16F15355-E/ML - 8-Bit 32MHz 14KB Flash MCU 28-QFN | Microchip

PIC16F15355-E/SP - 8-Bit MCU, 14KB Flash, 28-SPDIP | Microchip

PIC16F15355-E/SS - 8-bit XLP MCU 14KB Flash 28-SSOP | Microchip

PIC16F15355-I/MV - 8-Bit MCU, 14KB Flash, 32MHz | Microchip

PIC16F15355-I/SO - 8-bit MCU, 14KB Flash, 32MHz, 28-SOIC | Microchip

PIC16F15355-I/SP - 14KB Flash 8-bit MCU, 32MHz, 28-SPDIP | Microchip