Integrierte Schaltungen

PIC16F15375-I/MV

PIC16F15375-I/MV - 14KB Flash, 32MHz 8-bit MCU, 40-UQFN | Microchip

The Microchip PIC16F15375-I/MV is an 8-bit PIC® microcontroller from the PIC16(L)F153xx family, delivering 32 MHz CPU performance with 14 KB (8K x 14 words) of Flash program memory, 1 KB of SRAM, and a rich set of Core Independent Peripherals (CIPs) inside a 40-pin UQFN (5x5 mm) package with exposed thermal pad. An 8-bit PIC microcontroller is a RISC-based single-chip computer built around a Harvard architecture with separate program and data buses; it integrates CPU, non-volatile Flash, RAM, EEPROM, and configurable peripherals into one IC. Within the broader taxonomy this places the device in the chain: 8-bit MCU -> microcontroller -> embedded controller -> semiconductor. PIC microcontrollers from Microchip target cost-sensitive, deterministic, low-power applications where interrupt-driven, hardware-state-machine peripherals can replace firmware loops. The PIC16F15375 integrates Intelligent Analog peripherals including a 10-bit ADC with computation, a 5-bit/8-bit DAC, a comparator, and a Zero-Cross Detect (ZCD). It also carries four Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), four 10-bit PWMs, two EUSART, SPI/I2C, a temperature-indicator module, and the eXtreme Low-Power (XLP) features that let active current stay below 100 µA/MHz and allow deep-sleep currents in the nanoamp range. The 40-UQFN (MV) package with exposed pad enables efficient thermal dissipation in compact designs. Architecturally, the device uses the enhanced mid-range 8-bit core with a 14-bit instruction word, a hardware stack, and interrupt-priority logic. The CIP suite lets events and waveform generation occur without CPU intervention - the CLC implements Boolean logic on-chip, while the CWG produces complementary dead-band outputs with auto-shutdown, ideal for switched-mode converters and LED drivers. Typical applications include industrial sensor nodes, low-power IoT edge devices, LED lighting controllers, white-goods and home-appliance user interfaces, small motor/valve control loops, and battery-powered metering instruments where XLP run/sleep duty-cycling extends battery life. When designing, size decoupling capacitors per the datasheet (typically 100 nF plus bulk), keep oscillator traces short, and tie the exposed pad to a clean ground pour for thermal and EMI performance. Use the CLC/CWG pairs to offload waveform timing from the CPU whenever possible to minimize active current. This page consolidates verified distributor pricing, drop-in alternatives from the same PIC16F153xx family, and practical design notes not present in the manufacturer datasheet - intended to shorten BOM validation and procurement cycles.

Angebot Kontakt

PIC16F15375-I/PT

PIC16F15375-I/PT - 8-Bit 32MHz 14KB Flash XLP MCU | Microchip

The Microchip Technology PIC16F15375-I/PT is an 8-bit PIC16 microcontroller featuring 32 MHz CPU speed, 14 KB (8K x 14) Flash program memory, and 1 KB RAM, housed in a 44-pin TQFP (10x10 mm) package. It belongs to the PIC16(L)F153xx product family, which combines Intelligent Analog, Core Independent Peripherals (CIPs), and eXtreme Low-Power (XLP) technology for energy-efficient embedded designs. A microcontroller (MCU) is a single-chip computer containing a CPU, memory (Flash/RAM/EEPROM), and programmable peripherals used to control embedded systems. The PIC16F15375 family sits in the hierarchy: PIC16F15375 -> 8-bit PIC MCU -> microcontroller -> semiconductor IC. It targets low-power applications where active current, sleep current, and peripheral integration dominate the design trade-off, with a supply range spanning 2.3 V to 5.5 V (at reduced clock speed at low voltage). Key features include 4 PWM channels, a 12-bit ADC with Computation, a 5-bit DAC, a comparator, Complementary Waveform Generator (CWG), two EUSART modules, and SPI/I2C communication. XLP technology provides deep-sleep currents in the nanoampere range and active currents below 50 uA/MHz, enabling battery-powered designs that run for years on a single cell. The PIC16F15375 architecture uses a Harvard RISC core with a 14-bit instruction word, 49 instructions, and a 32 MHz internal oscillator that requires no external crystal. Core Independent Peripherals (CIPs) such as CWG, NCO, and configurable logic cells offload timing-critical tasks from the core, freeing the CPU for application logic and improving system determinism. Typical applications include IoT sensor nodes, low-power wireless sensor platforms, battery-powered home automation, motor control with PWM, lighting control, and small consumer appliances. The combination of low power, integrated analog, and abundant communication peripherals makes it well-suited to designs that must wake, sense, communicate, and return to sleep with minimal energy. When designing with this device, ensure the supply voltage matches the chosen clock speed: full 32 MHz operation requires 3.0 V or higher, while 16 MHz is supported down to 2.3 V. Use the MPLAB X IDE and MPLAB XC8 compiler for code development, and Microchip's Code Configurator (MCC) for visual peripheral setup. This page consolidates distributor pricing, drop-in alternatives, and design notes not available in the manufacturer datasheet alone, giving engineers a single reference for selecting and sourcing the PIC16F15375-I/PT.

Angebot Kontakt

PIC16F15375T-I/ML

PIC16F15375T-I/ML - 14KB Flash 8-Bit MCU, 44-QFN | Microchip

The Microchip Technology PIC16F15375T-I/ML is a 14KB Flash 8-bit PIC microcontroller built on an enhanced mid-range RISC core, housed in a 44-pin QFN package with exposed pad (8x8 mm). It operates up to 32 MHz, integrates 1024 bytes of SRAM and 1KB of EEPROM, and combines Intelligent Analog, Core Independent Peripherals (CIPs), and eXtreme Low-Power (XLP) technology. The device supports a wide 2.3V to 5.5V operating voltage range and is rated for the industrial -40C to +85C temperature class. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM, EEPROM), and a rich set of peripherals onto one silicon die. PIC microcontrollers occupy the 8-bit microcomputer node of the semiconductor taxonomy (8-bit MCU -> microcontroller -> embedded processor -> semiconductor). Within that hierarchy, the PIC16F153xx family is positioned as a "full-featured" line, meaning it includes advanced analog and communication peripherals beyond legacy baseline PIC16 devices, while keeping the instruction set simple and the cost low. Key features of the PIC16F15375T-I/ML include up to 14KB self-programmable Flash program memory, four 8-bit timers and five 16-bit timers, a 10-bit ADC with up to 35 analog channels, two comparators, two 10-bit PWMs and two 16-bit PWMs with complementary outputs, plus EUSART, I2C and SPI communication interfaces. The CIP set enables hardware state-machine functions such as the Configurable Logic Cell (CLC), Numerically Controlled Oscillator (NCO), Complementary Waveform Generator (CWG), and Zero-Cross Detect (ZCD), allowing designers to offload tasks from the CPU. Architecturally, the part uses a 14-bit instruction word RISC core with a hardware multiplier and a 32-level stack. The wide operating voltage and XLP features (nanoWatt XLP sleep currents in the nA range, Idle/Doze modes, peripheral module disable) make it suitable for battery-powered or energy-harvesting systems. The integrated temperature indicator and multiple interrupt sources further support robust embedded designs. Typical applications include consumer and industrial IoT sensor nodes, battery-powered remote controls, white goods and appliance control boards, automotive body and interior modules, LED lighting controllers, and low-cost digital thermostats. The combination of 14KB Flash and the large pin-count 44-QFN package is also well matched to graphical LCD user interfaces and motor-control peripheral boards. A key design consideration is that the 44-QFN (8x8 mm) package requires a thermal pad that must be soldered to a properly sized PCB copper pour for heat dissipation and ground integrity. The 'T' suffix in the MPN denotes Tape and Reel packaging, while 'I' denotes the industrial temperature range. The /ML suffix specifically identifies the 44-pin QFN with EP variant. Designers should consult the device's family datasheet (DS40001802) for full pin assignments, since the same PIC16F15375 die is also offered in 40-pin PDIP, 44-pin TQFP, and 48-pin packages.

Angebot Kontakt

PIC16F15375T-I/MV

PIC16F15375T-I/MV - 8-bit MCU, 14KB Flash, 40-UQFN | Microchip

The Microchip PIC16F15375T-I/MV is an 8-bit PIC microcontroller from the PIC16F153XX family, delivering 14 KB of Flash program memory, 1 KB of RAM, and a 32 MHz CPU core in a 40-pin UQFN (5x5 mm) package with exposed pad. It combines Intelligent Analog peripherals, Core Independent Peripherals (CIPs), and eXtreme Low-Power (XLP) technology, making it well-suited for general-purpose embedded designs where both analog performance and standby current matter. An 8-bit microcontroller (MCU) is a small, self-contained computer on a single IC that integrates a CPU, non-volatile program memory (typically Flash), volatile RAM, and a configurable set of digital and analog peripherals. PIC microcontrollers use a RISC instruction set and Modified Harvard architecture, occupying a hierarchy of 8-bit MCU -> microcontroller -> embedded controller -> semiconductor. They are widely used in sensor interfaces, consumer appliances, motor control front-ends, and low-power IoT edge nodes because they deliver deterministic execution at very low active and sleep currents. Key features include 4 PWM modules, a Comparator, a 5-bit DAC, an ADC, a Complementary Waveform Generator (CWG), 4 Configurable Logic Cells (CLC), 2 EUSART, and SPI/I2C. The device supports 1.8V-5.5V operation, enabling direct connection to single-cell Li-ion, 2xAA, and 3.3V digital rails without external level shifting. The XLP Sleep mode with nanowatt-class current extends battery life in duty-cycled applications such as remote controls and wireless sensor nodes. The PIC16F15375 family uses a 14-bit instruction word and an internal 32 MHz oscillator, with multiple clock options for power/performance trade-off. Peripherals like CLC allow combinatorial logic to be implemented in hardware without CPU intervention, offloading real-time tasks and enabling deterministic response times for safety-sensitive signal chains. Typical applications include IoT sensor nodes, home automation, low-power motor control (fans, BLDC commutation assistance), battery-powered consumer products, and industrial sensor hubs. The wide voltage range and rich peripheral set allow a single MCU to handle sensing, communication, and local control without external logic. Designers should note that the 40-UQFN package includes an exposed thermal pad that must be soldered to the ground plane for mechanical reliability and thermal dissipation. Decoupling capacitors (100 nF + bulk) should be placed within a few millimeters of the VDD pins to support ADC and DAC accuracy. Migrating between PIC16F15375 variants (28/40/44/48-pin) requires re-validating pin assignments but not firmware, because the peripherals are identical across pin counts. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a faster path to selecting and qualifying a pin-compatible replacement.

Angebot Kontakt

PIC16F15375T-I/PT

PIC16F15375T-I/PT - 14KB Flash 8-bit MCU | Microchip

The Microchip Technology PIC16F15375T-I/PT is an 8-bit PIC microcontroller from the PIC16F153xx family, delivering 14KB (8K x 14) of Flash program memory and 1KB of RAM in a 44-pin TQFP (10x10 mm) package. It operates at up to 32 MHz and supports 2.3V to 5.5V supply, integrating intelligent analog, Core Independent Peripherals (CIPs), and eXtreme Low-Power (XLP) technology for battery-friendly designs. An 8-bit microcontroller (MCU) is a single-chip computer that combines a CPU, RAM, non-volatile program memory, and peripherals on one die. The "8-bit" refers to the width of its data path and ALU; 8-bit PIC MCUs use a modified Harvard RISC architecture optimized for deterministic interrupt response, low power, and ease of use. PIC16F1xxx devices sit in the mid-range PIC family, balancing cost, code density (14-bit instruction word), and rich on-chip peripherals for embedded control tasks. They are commonly used as the main system controller in IoT nodes, sensor hubs, and consumer appliances, or as co-processors for housekeeping and user-interface tasks. Key features of the PIC16F15375 include 14KB Flash, 1KB SRAM, up to 36 digital I/O pins, a 10-bit ADC, multiple 8/10-bit DACs, four PWM outputs with Complementary Waveform Generator (CWG), comparators, two EUSART, SPI, and I2C. eXtreme Low-Power features such as Idle and Sleep modes, peripheral module disable, and nanoWatt XLP technology make it well-suited to battery-powered products. The 32 MHz internal oscillator removes the need for an external crystal in many designs. The device uses the enhanced mid-range PIC16 core with a 14-bit instruction set, hardware multiply assist, and a vectored interrupt controller. Internal data EEPROM emulation through Flash, a configurable logic cell (CLC), and signal measurement timers (SMT) provide Core Independent Peripherals that offload the CPU. Intelligent analog peripherals allow closed-loop control without an external ADC/DAC chain, reducing BOM cost on sensor and motor-control boards. Typical applications include low-power IoT sensor nodes, home automation controllers, battery-powered handheld instruments, LED lighting controls, motor-control front ends, and human-machine interface (HMI) panels. The combination of XLP, 5.5V tolerance, and rich analog peripherals makes it especially attractive for industrial sensor conditioning and small appliances. When designing, ensure VDD decoupling uses a 100 nF ceramic capacitor placed within 5 mm of the IC. Use the ICSP header for production programming; for low-power designs, enable the watchdog timer and use Sleep with peripheral interrupts to achieve microamp standby currents. Verify that any unused I/O pins are configured as outputs low to minimize current leakage on the TQFP-44 package. This page synthesizes distributor pricing, drop-in alternatives from the same TQFP-44 footprint, and practical design notes not found in the manufacturer datasheet alone, giving engineers and buyers a single decision-making reference.

Angebot Kontakt

PIC16F15376-E/ML

PIC16F15376-E/ML - 8-bit MCU, 28KB Flash, 44-QFN | Microchip

The Microchip Technology PIC16F15376-E/ML is an 8-bit PIC RISC microcontroller with 28KB Flash, 2KB RAM, and a 32MHz CPU, housed in a 44-pin QFN (8x8 mm) exposed-pad package. It belongs to the PIC16(L)F153xx family and integrates Intelligent Analog, Core Independent Peripherals (CIPs), and eXtreme Low-Power (XLP) technology for energy-constrained applications. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), data memory (RAM), and integrated peripherals such as timers, ADCs, and communication interfaces. Within the PIC architecture, the 8-bit PIC16 family occupies the entry-level to mid-range tier of Microchip's portfolio, balancing code density, peripheral integration, and low power consumption. The PIC16F15376 sits in the upper end of this family due to its 28KB Flash and rich CIP set, placing it above smaller 14KB/7KB members while remaining below 32-bit MCU classes such as PIC32 or Cortex-M. Key features include four 16-bit PWMs with complementary waveform generation, a 10-bit ADC with computation, a 5-bit/8-bit DAC, two comparators, four Configurable Logic Cells (CLCs), a Complementary Waveform Generator (CWG), and two EUSART plus SPI/I2C interfaces. The XLP technology delivers nanoWatt deep-sleep currents below 60 nA typical, making the part attractive for battery-powered sensor nodes. The device uses a modified Harvard architecture with a 14-bit instruction word and a 32MHz internal oscillator (±1% accuracy after calibration). Its peripheral pin-select (PPS) feature allows flexible remapping of digital peripherals to any I/O pin, simplifying PCB routing for complex designs. The 44-QFN exposed-pad package provides 36 programmable I/O pins with up to 25 mA source/sink per pin. Typical applications include IoT sensor nodes, home appliances, LED lighting control, low-power wireless HMI front-ends, and small motor-control loops. The combination of CLCs and CWG enables standalone waveform generation without CPU intervention, freeing the core for higher-level tasks. When designing with this MCU, ensure the exposed pad is soldered to a sufficient copper pour (recommended at least 25 mm²) for thermal dissipation, and place a 0.1 µF decoupling capacitor within 3 mm of each power pin. Use MPLAB X IDE with the XC8 compiler for firmware development. This page synthesizes distributor pricing, drop-in alternatives from the PIC16F153xx family, and practical design notes not consolidated in the manufacturer datasheet.

Angebot Kontakt

PIC16F15376-E/MV

PIC16F15376-E/MV - 8-Bit MCU, 32MHz, 28KB Flash, 40-UQFN | Microchip

The Microchip Technology PIC16F15376-E/MV is an 8-bit RISC PIC16 microcontroller running at up to 32 MHz, integrating 28 KB of Flash program memory, 2 KB of SRAM, and 35 channels of 10-bit ADC inside a 40-pin 5x5 mm UQFN package (MV). It belongs to the PIC16(L)F153XX family that combines Intelligent Analog, Core Independent Peripherals (CIPs), and eXtreme Low-Power (XLP) technology to address low-power embedded designs across consumer, industrial, and automotive sensor-node applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and a range of peripheral IP into one package, enabling compact embedded control. The PIC16F15376 specifically sits in the 8-bit MCU class (PIC -> 8-bit microcontroller -> microcontroller -> embedded processor) and uses Microchip's enhanced mid-range core with a 14-bit instruction word, making it more code-efficient than legacy baseline PIC cores while retaining the family ecosystem of compilers, programmers, and CIPs. Key features include four 10-bit PWMs with Complementary Waveform Generator (CWG), two rail-to-rail Comparators, a 5-bit DAC, four Configurable Logic Cells (CLC), two EUSART (LIN-capable), two SPI, and two I2C peripherals, plus an on-chip 32 MHz internal oscillator that eliminates the external crystal in many designs. The 'E' temperature grade supports -40C to +125C operation, suitable for automotive and harsh-environment deployments. The device is fabricated on a CMOS process with XLP power management, allowing Active mode current in the microamp range and deep-sleep currents typically below 100 nA. This makes the part attractive for battery-powered sensor nodes that must wake periodically, take a measurement, transmit over UART or SPI, and return to sleep. The CIPs (CLC, NCO, CWG) let designers implement glue logic in silicon, reducing BOM cost and freeing the CPU from bit-banging tasks. Typical applications include IoT sensor end-nodes, low-power wireless modules, HVAC and white-goods control panels, automotive body and lighting controllers, and consumer appliances. Combined with the generous 28 KB Flash, the part fits medium-complexity state-machine firmware while leaving headroom for bootloaders or wireless stacks. Designers should pay attention to the UQFN EP exposed pad - it must be soldered to the board ground pour for thermal and electrical performance, and decoupling requires a 0.1 uF VDD cap within 3 mm of each power pin. For production programming, use the 4-wire In-Circuit Serial Programming (ICSP) header defined in the family datasheet. This page synthesizes XAIPART distributor pricing, a curated drop-in alternative list limited to same-package 40-UQFN variants, and engineering design notes compiled from Microchip's family datasheet and TB documents, going beyond what the manufacturer datasheet alone offers.

Angebot Kontakt

PIC16F15376-E/P

PIC16F15376-E/P - 8-bit MCU, 28KB Flash, 40-PDIP | Microchip

The Microchip Technology PIC16F15376-E/P is an 8-bit PIC microcontroller from the PIC16(L)F153xx family, featuring 28 KB of Flash program memory, 32 MHz CPU speed, and housed in a 40-pin PDIP (DIP-40) through-hole package. The device integrates intelligent analog peripherals, Core Independent Peripherals (CIPs), and eXtreme Low-Power (XLP) technology, targeting low-power and general-purpose embedded applications. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, RAM, Flash program memory, and peripherals into one package. PIC microcontrollers from Microchip use a modified Harvard RISC architecture with separate program and data buses, executing instructions in a single cycle except for branches. The PIC16F153xx family sits in the PIC16 mid-range tier — between PIC10/12/16 baseline parts and PIC18/dsPIC enhanced parts — and is engineered for low-power, mixed-signal embedded designs. Key features of the PIC16F15376 include 28 KB Flash, 2 KB RAM, up to 32 MHz operation, 35 instructions, and 14-bit instruction width. The -E/P suffix designates the extended temperature grade (-40 °C to +125 °C) in a PDIP-40 package. On-chip peripherals include 10-bit ADC with computation (ADC2), 8-bit DAC, configurable logic cells (CLC), numerically controlled oscillator (NCO), complementary waveform generator (CWG), zero-cross detect (ZCD), and multiple communications peripherals (I2C, SPI, UART, and LIN-compatible EUSART). The architecture combines a 14-bit instruction word with a hardware multiplier and a wide operating voltage range of 1.8 V to 5.5 V, supporting both 3.3 V and 5 V system designs. The XLP idle/active current figures (typically tens of µA in active, hundreds of nA in sleep) make it suitable for battery-backed and energy-harvesting applications. Typical applications include IoT sensor nodes, smart home devices, industrial control, consumer white goods, and battery-powered handheld instruments. The combination of CIPs (CLC, NCO, CWG) enables offloading of timing-critical functions from the CPU, while the ADC2 simplifies sensor signal conditioning with on-chip filtering and averaging. When designing with this part, plan the PCB for the 40-pin DIP package (0.600 in / 15.24 mm row spacing) and reserve ICSP header footprint for in-circuit programming and debugging. The DIP form factor also suits prototyping on breadboards and through-hole development boards. This page synthesizes distributor pricing, drop-in alternatives, application guidance, and design notes not collected in a single location by the manufacturer datasheet.

Angebot Kontakt

PIC16F15376-E/PT

PIC16F15376-E/PT - 32MHz 28KB Flash 8-bit MCU | Microchip

The Microchip Technology PIC16F15376-E/PT is an 8-bit PIC microcontroller from the PIC16(L)F153XX family, featuring 28KB of Flash program memory, 2048 bytes of RAM, and a 32MHz internal oscillator in a 44-pin TQFP (10x10 mm) package. It combines Intelligent Analog, Core Independent Peripherals (CIPs), and eXtreme Low-Power (XLP) technology for energy-efficient embedded designs. An 8-bit PIC microcontroller is a compact, deterministic processor built around a Harvard-architecture RISC core optimized for low-power, real-time control. PIC microcontrollers belong to the microcontroller -> embedded processor -> semiconductor device hierarchy. The XLP variant adds nanoWatt sleep modes and peripheral modules that can operate while the CPU is halted, making the family well-suited for battery-powered sensor nodes and IoT endpoints. Key features of this part include 4 PWM channels, a comparator, a 5-bit DAC, a 10-bit ADC, a Complementary Waveform Generator (CWG), 4 Configurable Logic Cells (CLC), 2 EUSART peripherals, and SPI/I2C communication interfaces. The device operates from 2.3V to 5.5V and supports eXtreme Low-Power modes with currents as low as nanoampere levels in deep sleep. The PIC16F15376 uses a RISC-based PIC16 core with a 14-bit instruction word and an internal 32MHz oscillator block with PLL, providing deterministic instruction execution and a wide peripheral set. Hardware-based CIPs offload timing-critical tasks from the CPU, allowing complex functions like waveform generation and signal conditioning to run autonomously. Typical applications include low-power IoT nodes, sensor interfaces, LED lighting control, consumer electronics, industrial control, and battery-powered monitoring. The 44-pin TQFP package provides ample I/O for system integration while remaining compact for space-constrained designs. When designing with this part, note the -E temperature grade of -40C to +125C suitable for industrial environments. Use the MPLAB X IDE with XC8 compiler for firmware development, and consider the PIC16F15376-I/PT (-40C to +85C) variant for commercial temperature ranges. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, enabling faster BOM decisions and second-source validation for production engineers.

Angebot Kontakt

PIC16F15376-I/ML

PIC16F15376-I/ML - 8-bit 32MHz 28KB Flash MCU | Microchip 44-QFN

The Microchip Technology PIC16F15376-I/ML is an 8-bit PIC microcontroller featuring a 32 MHz CPU, 28 KB (16K x 14) of Flash program memory, and 2 KB of SRAM, housed in a 44-pin QFN (8x8 mm) package with an exposed thermal pad. It belongs to the PIC16(L)F153xx family that combines eXtreme Low-Power (XLP) technology with rich Core Independent Peripherals (CIPs) including up to 4 PWMs, comparators, a DAC, ADC, CWG, 4 CLC blocks, 2 EUSART, and SPI/I2C interfaces, operating from 2.3V to 5.5V. An 8-bit microcontroller (MCU) is a programmable processor built around an 8-bit data path, optimized for low cost, deterministic real-time control, and ultra-low power consumption. PIC MCUs sit within the broader hierarchy: microcontroller -> embedded processor -> semiconductor -> integrated circuit. They are widely used for sensor interfacing, motor control, IoT endpoints, and consumer white goods where low-power sleep modes and deterministic interrupt response are critical. Key differentiating features of this part include XLP sleep currents that extend battery life, four Configurable Logic Cells (CLC) for hardware state-machine implementation without CPU overhead, a Complementary Waveform Generator (CWG) for power-conversion timing, and a 10-bit ADC with computation. The 28 KB Flash and 2 KB SRAM are well-balanced for protocol stacks such as Modbus or LIN, and the dual EUSART blocks support simultaneous host and field-bus communication. Architecturally, the PIC16F15376 uses a 14-bit instruction word with a RISC-style pipeline, vectored interrupts, and peripheral pin select (PPS) that allows flexible I/O mapping. The internal 32 MHz oscillator eliminates external timing components in many designs. The combination of CWG, NCO, and CLC enables sophisticated power conversion and lighting control in hardware without taxing the core. Typical applications include IoT sensor nodes, low-power wireless sensor hubs, LED lighting controllers, small home appliances, HVAC damper control, battery chargers, automotive body electronics, and general-purpose embedded control for industrial sensors and meters. When designing with this device, ensure the exposed pad (EP) on the QFN-44 is soldered to a sufficiently large copper area for thermal dissipation and electrical grounding. Decouple VDD with a 100 nF ceramic capacitor placed within 5 mm of each power pin, and configure the PPS registers carefully because remapping is non-volatile only after a configuration bit lock. This page synthesizes distributor pricing, drop-in alternative part numbers, and practical design notes that complement the manufacturer datasheet for engineers selecting the PIC16F15376-I/ML for new designs or replacements.

Angebot Kontakt

PIC16F15376-I/MV

PIC16F15376-I/MV - 32MHz 8-bit MCU, 28KB Flash, 40-UQFN | Microchip

The Microchip PIC16F15376-I/MV is an 8-bit PIC16F microcontroller built on an enhanced mid-range core that integrates 28 KB of Flash program memory, 2 KB of SRAM, and Core Independent Peripherals (CIPs) such as CLC, CWG, and Configurable Logic in a compact 40-pin UQFN (5x5 mm) package with an exposed pad. The device runs at up to 32 MHz across a 2.3 V to 5.5 V supply range and combines Intelligent Analog (12-bit ADC with computation, 5-bit DAC, two comparators) with rich communication peripherals, including two EUSART, two SPI, and two I2C. eXtreme Low-Power (XLP) features such as idle/doze/sleep modes, peripheral module disable, and <1 µA typical sleep current suit it for battery-aware designs. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, data memory, and peripherals into one package and executes instructions one byte at a time. Within the broader taxonomy, 8-bit MCUs sit below 16-bit and 32-bit microcontrollers in computational throughput but excel in deterministic real-time response, low cost, and ultra-low standby current. The PIC16 family belongs to Microchip's mid-range enhanced 8-bit portfolio, occupying the LDO-equivalent niche for microcontrollers: small, efficient, and ubiquitous in cost-sensitive and battery-powered embedded systems. Key features include 35 instructions (14-bit wide), 36 general-purpose I/O pins, four 10-bit PWM modules, two 8-bit timers plus one 16-bit timer, and a 32 kHz internal oscillator that reduces external component count. Up to 28 KB self-writeable Flash supports in-application updates and EEPROM emulation, while 256 B of EEPROM-like data storage aids parameter retention. Hardware math accelerator, zero-cross detection, and a windowed watchdog timer further reduce firmware load. Architecturally, the PIC16F15376 separates CPU execution from CIP state machines, freeing the core from bit-banging tasks and improving EMI/EMC robustness. The 40-UQFN MV package with wettable flanks supports high-density SMT layouts and IP-rated enclosures, while the MV suffix indicates the extended (–40 °C to +85 °C) industrial temperature grade and UQFN carrier. Typical applications include IoT sensor nodes, home appliance user interfaces, low-cost motor control (BLDC and stepper), LED lighting controllers, battery chargers, and industrial sensor hubs. Designers choose the PIC16F15376-I/MV when deterministic real-time behavior, low sleep current, and rich on-chip analog/peripheral integration outweigh the need for higher CPU throughput. When designing with this part, consider that CIPs handle encoder, PFC, and timing sequences in hardware; allocate I/O carefully because the UQFN EP pad must be soldered for thermal and electrical performance.

Angebot Kontakt

PIC16F15376-I/P

PIC16F15376-I/P - 8-Bit MCU, 32MHz, 28KB Flash, 40-PDIP | Microchip

The Microchip Technology PIC16F15376-I/P is an 8-bit PIC microcontroller from the PIC16F153xx family, featuring a 32MHz CPU, 28KB Flash program memory, 2KB SRAM, and a 40-pin PDIP (DIP-40) through-hole package. The -I suffix denotes the industrial operating temperature grade of -40C to +85C, while the /P suffix designates the 0.600 inch (15.24mm) PDIP form factor for breadboard-friendly prototyping and legacy through-hole assembly. What is a PIC16 8-bit microcontroller? PIC16 (Peripheral Interface Controller 16-bit instruction width) microcontrollers are RISC-based CMOS MCUs from Microchip Technology that form the backbone of the mid-range 8-bit embedded portfolio. They sit within the hierarchy: PIC10/12/16/18 families -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. PIC16F parts add Flash program memory and the XLP (eXtreme Low-Power) sleep modes, making them suitable for battery-powered and always-on applications. Key features of the PIC16F15376 include four 10-bit PWMs with independent time bases, a 5-bit DAC with 32 taps, a rail-to-rail comparator, a 10-bit ADC with computation, the Complementary Waveform Generator (CWG), four Configurable Logic Cells (CLC) for hardware glue logic, two EUSART, SPI, and I2C peripherals. The Core Independent Peripherals (CIPs) allow timers, PWM, and communication to operate without CPU intervention, reducing firmware overhead and deterministic jitter. The device operates from 2.3V to 5.5V and supports eXtreme Low-Power (XLP) modes with nanoWatt technology, drawing typically under 50 nA in sleep with peripherals disabled. This combination of low power and abundant CIPs allows the part to wake, perform a sensor read, communicate, and return to sleep autonomously, an architecture suited for IoT sensor nodes and remote controls. Typical applications include consumer white goods and small appliances, IoT sensor endpoints, low-cost motor control via CWG and PWM, battery-powered data loggers, industrial sensor interfaces, and human-machine interface (HMI) panels with segmented displays. The 40-pin DIP package is frequently chosen for educational labs, breadboard prototypes, and through-hole manufacturing lines that have not transitioned to surface mount. When designing with this part, ensure the in-circuit serial programming (ICSP) pins (ICSPCLK/ICSPDAT) and the MCLR reset pin have proper isolation per the datasheet, and use MPLAB X IDE with XC8 compiler for firmware development. The high pin count and 28KB Flash also leave headroom for adding USB stacks, bootloaders, or wireless protocol drivers later in the product cycle. This page synthesizes distributor pricing, same-package drop-in PIC16F15376 family alternatives, and practical design notes not found in the manufacturer datasheet, providing an AEO-optimized engineer reference for selection and procurement.

Angebot Kontakt

PIC16F15376-I/PT

PIC16F15376-I/PT - 8-Bit 32MHz 28KB Flash MCU | Microchip

The Microchip Technology PIC16F15376-I/PT is an 8-bit PIC16 microcontroller featuring 28KB of self-programmable Flash program memory, 2KB of RAM, and a maximum CPU clock speed of 32MHz, housed in a 44-pin TQFP (PT) package measuring 10x10 mm. It combines the PIC16 RISC core with Core Independent Peripherals (CIPs), Intelligent Analog, and eXtreme Low-Power (XLP) technology, targeting a broad range of low-power and general-purpose embedded designs. An 8-bit microcontroller (MCU) is a small computing system on a single integrated circuit containing a CPU, non-volatile program memory (Flash), volatile working memory (RAM), and programmable I/O peripherals. Within the embedded hierarchy, the PIC16F15376 belongs to the PIC16 family -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. The 8-bit architecture remains widely adopted for cost-sensitive, deterministic, low-power applications where computational throughput requirements are modest but peripheral integration and ultra-low standby current are critical. Key specifications include 28KB (16K x 14 words) of Flash, 2KB of RAM, four 10-bit PWM outputs, a 10-bit ADC with automatic accumulation, a 5-bit DAC, two Enhanced Universal Synchronous Asynchronous Receiver Transmitters (EUSART), SPI, and I2C communication peripherals. The device also integrates a Comparator, Complementary Waveform Generator (CWG), Zero-Cross Detection (ZCD), and a temperature indicator. XLP technology delivers typical sleep currents below 50 nA, enabling battery-powered designs with multi-year lifetimes. The architecture uses a Harvard-style RISC core with a 14-bit instruction word and a single-cycle 32MHz oscillator block with internal HFINTOSC. Internal peripherals operate autonomously via Peripheral Pin Select (PPS) signal routing, allowing reassignment of peripheral functions to alternative pins without package changes. The 44-pin TQFP package exposes up to 36 GPIO pins, sufficient for sensor fusion, user-interface I/O, and display-driving applications. Typical applications include IoT sensor nodes, home-appliance controls, low-energy wireless sensor platforms, LED lighting controllers, and battery-powered metering. The combination of Intelligent Analog (10-bit ADC, DAC, comparator) and CWG enables direct driving of power-conversion stages, including PFC and LLC converters. For designers, selecting the 'I' industrial temperature grade (-40C to +85C) ensures robust operation across commercial and industrial environments without additional qualification steps. This page synthesizes distributor pricing, verified drop-in alternatives from Microchip's same-family cross-reference, and practical design notes not found in the standalone manufacturer datasheet.

Angebot Kontakt

PIC16F15376T-I/ML

PIC16F15376T-I/ML - 8-bit 32MHz 28KB Flash MCU 44-QFN | Microchip

The Microchip Technology PIC16F15376T-I/ML is an 8-bit PIC® microcontroller built on the XLP™ (eXtreme Low-Power) 16F platform, delivering 32MHz CPU performance, 28KB of Flash program memory, and 2KB of RAM in a 44-pin QFN (8x8 mm) package. The device integrates Core Independent Peripherals (CIPs), Intelligent Analog, and multi-protocol serial communication including 2 EUSART, SPI, and I2C, making it a versatile choice for mixed-signal embedded designs. An 8-bit microcontroller (MCU) is a programmable processor with an 8-bit data path optimized for cost-sensitive, deterministic, low-power embedded control. PIC® MCUs combine a RISC-based CPU core with on-chip Flash, RAM, peripherals, and interrupt-driven I/O, occupying a position in the broader taxonomy of microcontrollers -> embedded processors -> semiconductors -> integrated circuits. The 16F family targets battery-powered, low-power, and motor-control applications where predictable behavior and minimal sleep current are critical. Key features of the PIC16F15376T-I/ML include 28KB (16K x 14 words) of self-programmable Flash, 2KB RAM, 4 PWM channels, an on-chip 5-/10-bit DAC, a rail-to-rail comparator, a 10-bit ADC, the Configurable Logic Cell (CLC), the Complementary Waveform Generator (CWG), and XLP™ nanoWatt sleep modes that drop current consumption below 1 µA. The CIPs handle events in hardware without CPU intervention, freeing the core for application-level tasks and reducing firmware complexity. Architecturally, the part uses an enhanced mid-range 8-bit core with a hardware multiplier, a 14-bit instruction word, and a vectored interrupt controller. Memory-mapped peripherals and a peripheral pin-select (PPS) engine allow flexible I/O mapping, while the internal 32MHz oscillator eliminates the need for an external crystal in many designs. This combination gives designers high integration in a compact 44-QFN (8x8 mm) footprint suitable for space-constrained PCBs. Typical applications include low-power IoT sensor nodes, BLDC and stepper motor control, LED lighting controllers, battery-powered instrumentation, and consumer appliances. The 44-QFN package with a generous ground-exposed pad provides excellent thermal dissipation for thermally limited designs. When designing with this device, place 100nF decoupling capacitors as close as possible to each VDD pin and tie the exposed pad (EP) to a clean ground plane. Programming/debug is via the in-circuit serial programming (ICSP) interface using a PICkit or MPLAB debugger. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a complete reference for sourcing and applying the PIC16F15376T-I/ML.

Angebot Kontakt

PIC16F15376T-I/MV

PIC16F15376T-I/MV - 28KB Flash 8-bit MCU | Microchip | XLP

The Microchip Technology PIC16F15376T-I/MV is an 8-bit PIC16 microcontroller built on the enhanced mid-range core, featuring 28KB (16K x 14) of Flash program memory, 2KB of RAM, and a maximum CPU clock of 32 MHz, housed in a 40-pin UQFN (5x5 mm) package. The device is part of the PIC16(L)F153xx family and integrates four 10-bit PWMs, a comparator, a 5-bit/8-bit DAC, a 10-bit ADC, a Complementary Waveform Generator (CWG), four Configurable Logic Cells (CLC), two EUSARTs, and SPI/I2C peripherals. The "T" suffix indicates Tape and Reel packaging, and the "I" temperature grade denotes an industrial -40C to +85C operating range. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and programmable I/O peripherals. Within the semiconductor hierarchy, an MCU belongs to the broader category of microcontrollers, then embedded processors, then digital ICs. The PIC16F15376T-I/MV is part of the 8-bit MCU subcategory that targets low-power and cost-sensitive applications. It uses a 14-bit instruction word and Harvard architecture, executing one instruction per clock cycle (except branches), which simplifies deterministic timing and interrupt-driven firmware design. Key differentiating features of the PIC16F15376T-I/MV include Microchip's eXtreme Low-Power (XLP) technology, with a typical sleep current below 50 nA, and Core Independent Peripherals (CIPs) such as CLC and CWG that offload timing-sensitive tasks from the CPU. The 10-bit ADC supports up to 35 channels, while the CWG can generate complementary PWM outputs with dead-band control, eliminating the need for external gate-driver timing circuits in half-bridge topologies. Combined, these peripherals reduce firmware complexity and BOM cost in motor control, lighting, and sensor-interface designs. Typical applications for the PIC16F15376T-I/MV include consumer white goods, LED lighting drivers, low-power IoT sensor nodes, battery-operated HVAC controls, simple BLDC/PMSM motor commutation, and general-purpose mixed-signal embedded platforms. Its 2.3V to 5.5V supply range and integrated intelligent analog blocks (ADC, DAC, comparator) make it well suited for direct sensor interfacing without external signal-conditioning ICs. The 40-UQFN (5x5) package supports space-constrained PCB layouts while exposing enough pins (36 I/O) for typical peripheral-rich designs. When designing with this device, ensure that the UQFN-40 land pattern uses sufficient thermal copper under the exposed pad to keep junction temperature within the industrial -40C to +85C range at full CPU load. Decouple VDD with a 100 nF ceramic capacitor placed within 3 mm of the pin, and keep the AVDD/VREF traces short to preserve ADC accuracy. The CLC and CWG should be configured before enabling peripherals to avoid spurious outputs on power-up. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Angebot Kontakt

PIC16F15376T-I/PT

PIC16F15376T-I/PT - 8-bit 32MHz MCU 28KB Flash 44-TQFP | Microchip

The Microchip Technology PIC16F15376T-I/PT is an 8-bit PIC16F microcontroller built on a RISC core running up to 32 MHz, integrating 28 KB of Flash program memory, 2 KB of SRAM, and 4x PWM, Comparator, 5-/8-bit DAC, ADC, CWG, 2x EUSART, and SPI/I2C peripherals in a 44-pin TQFP (10x10 mm) package. The 'T' suffix denotes tape-and-reel packaging and 'I' denotes the -40C to +85C industrial temperature range. An 8-bit microcontroller (MCU) is a programmable integrated circuit that executes instructions from on-chip Flash memory using an internal data path of 8 bits. Within the broader taxonomy, the PIC16F15376 belongs to the 8-bit microcontroller family -> PIC16 family -> PIC16F1xxx enhanced mid-range -> PIC microcontroller -> microcontroller -> embedded processor -> semiconductor. 8-bit MCUs are favored for deterministic control loops, low-power operation, and cost-sensitive applications where 32-bit performance is not required. Key features of the PIC16F15376T-I/PT include four 10-bit PWM channels with complementary output capability, a 10-bit ADC with up to 43 channels, a 5-bit and 8-bit DAC, two EUSART modules for asynchronous and synchronous serial communication, and Microchip's Core Independent Peripherals (CIPs) such as the Configurable Logic Cell (CLC), Complementary Waveform Generator (CWG), and Numerically Controlled Oscillator (NCO). The eXtreme Low-Power (XLP) technology provides sleep currents in the nanoampere range. The device is fabricated on a low-power CMOS process and supports an operating voltage range of 2.3 V to 5.5 V, making it compatible with both 3.3 V and 5 V systems. The 44-TQFP package provides ample I/O count for multi-protocol sensor hubs, motor control boards, and human-machine interface (HMI) front panels. On-board debug support is provided through the in-circuit debug (ICD) interface and the MPLAB X IDE ecosystem. Typical applications include motor control (BLDC and stepper), LED lighting drivers, power conversion (digital SMPS feedback), smart sensors, IoT end nodes, and consumer appliances. The combination of CIPs and XLP makes it a strong fit for applications where the MCU must offload timing-critical tasks from the CPU and remain idle for extended periods to extend battery life. When designing with this part, ensure that decoupling capacitors (100 nF plus 1 uF bulk) are placed within 5 mm of each power pin, and that the ICSP/ICD pins are routed to a 6-pin header for in-circuit programming and debugging. Designers should also leave room for the oscillator layout - either a 2-pin crystal or an internal 32 MHz HFINTOSC reference, the latter eliminating the need for external timing components in space-constrained designs. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, enabling faster design-in and sourcing decisions.

Angebot Kontakt

PIC16F15376T-I/PTVAO

PIC16F15376T-I/PTVAO - 8-bit 32MHz 28KB Flash MCU | Microchip

The Microchip Technology PIC16F15376T-I/PTVAO is an 8-bit PIC16 microcontroller from the PIC16(L)F153XX family, operating at up to 32 MHz with 28 KB of Flash program memory and 2 KB of RAM, housed in a 44-pin TQFP package (10x10 mm). The part suffix T-I/PTVAO designates tape-and-reel packaging, industrial temperature range (-40C to +85C), the 44-pin TQFP package, and the automotive (VAO) ordering code suffix. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and a rich set of on-chip peripherals such as timers, ADC, comparators, PWM, and communication interfaces. PIC microcontrollers sit within the broader 8-bit MCU category alongside 8051 and AVR families, and they are used as the central processing element in countless embedded systems. They typically fall under the system hierarchy: microcontroller -> embedded processor -> semiconductor device. Key features of this part include 4 independent PWM modules with complementary outputs, up to 38 digital I/O pins, a 10-bit ADC, multiple Core Independent Peripherals (CIPs) such as CWG, NCO, and configurable logic cells, plus an integrated temperature indicator. The XLP (eXtreme Low Power) technology keeps active current low and supports deep-sleep currents in the nanoampere range, making the device well suited to battery-powered and energy-harvesting applications. The architecture uses a 14-bit instruction word with a hardware stack, which is a hallmark of the PIC16 mid-range family. The CIPs allow complex timing, motor, and signal-conditioning tasks to run without CPU intervention, freeing the core for application logic and improving deterministic real-time response. Typical applications include IoT sensor nodes, automotive body and interior modules, white-goods and appliance control, low-power remote controls, lighting controls, and small motor/PMW-driven loads such as fans and pumps. The integrated comparators and op-amp options also support analog signal conditioning in sensor-interface designs. When designing with this part, ensure that the 44-pin TQFP footprint is suitable for the target PCB and that the debugger/ programmer selection (such as PICkit 4 or MPLAB ICD 4) is configured for the PIC16F153XX device ID. The automotive VAO suffix does not by itself indicate AEC-Q100 qualification status; that must be verified separately.

Angebot Kontakt

PIC16F15385-E/MV

PIC16F15385-E/MV - 8-bit MCU, 14KB Flash, 32MHz, 48-UQFN | Microchip

The Microchip Technology PIC16F15385-E/MV is an 8-bit PIC microcontroller from the PIC16(L)F153xx family featuring 14KB (8K x 14) of Flash program memory, 1KB of RAM, and a 32MHz internal oscillator in a 48-pin UQFN (MV) 6x6mm package with exposed thermal pad. Operating from 2.3V to 5.5V, the -E temperature grade extends from -40°C to +125°C for industrial and harsh-environment deployments. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash/ROM), data memory (RAM), and peripherals onto one silicon die. The PIC16F15385 sits in the hierarchy: 8-bit MCU -> PIC16 family -> PIC16F153xx sub-family -> Microchip XLP low-power platform, combining a RISC core with Core Independent Peripherals (CIPs) such as CLC, CWG, and NCO that execute complex sequencing without CPU intervention. Key features include four Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), four 10-bit PWMs, a 10-bit ADC with Computation (ADC2), a 5-bit/8-bit DAC, two comparators, two EUSART, SPI/I2C, and eXtreme Low-Power (XLP) sleep modes drawing as little as 30 nA. Intelligent Analog peripherals enable sensor interfacing without external components. The device uses a 14-bit instruction word RISC architecture optimized for deterministic interrupt response, allowing event-driven designs that offload timing-critical tasks to peripherals via Peripheral Pin Select (PPS). The 32MHz internal oscillator (±1% calibrated) eliminates an external crystal in cost-sensitive designs. Typical applications include IoT sensor nodes, home automation controllers, battery-powered remote controls, low-power wireless sensor hubs, BLDC/PMSM motor commutation logic, and industrial sensor signal conditioning. The wide 2.3V-5.5V range and XLP sleep modes make it especially suited for coin-cell and energy-harvesting products. When designing with this part, place a 0.1 µF decoupling capacitor within 3 mm of every VDD pin and tie all unused I/O to defined logic levels to minimize current leakage. Verify PPS mappings for your chosen peripherals in the MPLAB Code Configurator before committing the pinout. This page synthesizes distributor pricing, drop-in alternatives from the PIC16F153xx family, and practical design notes not collected in the manufacturer datasheet.

Angebot Kontakt

PIC16F15385-I/PT

PIC16F15385-I/PT - 8-Bit 32MHz 14KB Flash MCU 48-TQFP | Microchip

The Microchip Technology PIC16F15385-I/PT is an 8-bit PIC microcontroller featuring a 32MHz CPU, 14KB (8K x 14 words) of Flash program memory, 1KB of RAM, and Core Independent Peripherals (CIPs), housed in a 48-pin TQFP (7x7) package. The device operates from 2.3V to 5.5V and is part of the PIC16(L)F153xx family with eXtreme Low-Power (XLP) technology. A microcontroller (MCU) is a single-chip computer containing a CPU core, non-volatile program memory (typically Flash), volatile working memory (RAM), and a configurable set of digital and analog peripherals. PIC16F family MCUs are RISC-based 8-bit microcontrollers from Microchip widely deployed in low-power and cost-sensitive embedded designs; they sit at the small-form-factor end of the broader microcontroller hierarchy (MCU -> embedded controller -> semiconductor IC). Key features include 4 PWMs, an on-chip comparator, a 5-bit/8-bit/10-bit DAC, an ADC with Computation, a Complementary Waveform Generator (CWG), 4 Configurable Logic Cells (CLC), 2 EUSART, and SPI/I2C communication. The XLP technology enables sleep currents down to nanoampere levels, making the device well-suited for battery-powered applications such as remote sensors and IoT endpoints. The PIC16F15385 uses an enhanced mid-range 8-bit RISC core with a 14-bit instruction word, providing deterministic instruction timing suitable for real-time control. The integrated CIPs (CLC, CWG, NCO, DSM) implement logic, waveform generation, and signal conditioning entirely in hardware, offloading tasks from the CPU and reducing firmware complexity and power consumption. Typical applications include low-power IoT sensor nodes, consumer electronics control, battery-operated remote controls, LED lighting drivers, small motor control loops, and general-purpose embedded systems requiring multiple serial interfaces and PWM channels. The wide operating voltage and XLP modes also suit energy-harvesting designs. When designing with this part, ensure decoupling follows Microchip's guidelines (typically a 100nF ceramic plus a bulk capacitor near VDD) and verify I/O voltage levels match peripheral expectations. Programming is supported via MPLAB X IDE and the PICkit/SNAP debuggers. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single source for selecting the PIC16F15385-I/PT.

Angebot Kontakt

PIC16F15385T-I/MV

PIC16F15385T-I/MV - 8-bit MCU, 14KB Flash, 48-UQFN | Microchip

The Microchip Technology PIC16F15385T-I/MV is an 8-bit PIC microcontroller from the PIC16F153XX family, integrating 14KB (8K x 14) of Flash program memory, 1KB of RAM, and 32MHz CPU performance in a 48-pin UQFN (6x6x0.5mm) tape-and-reel package. It belongs to Microchip's eXtreme Low-Power (XLP) family and supports 2.3V to 5.5V operation with up to 44 I/O pins. The 'T' suffix indicates Tape & Reel packaging, 'I' denotes the industrial -40C to +85C temperature range, and '/MV' identifies the UQFN-48 package. An 8-bit PIC microcontroller is a RISC-based embedded processor that combines a CPU, RAM, Flash, and configurable peripherals on a single die. PIC MCUs sit within the broader microcontrollers (MCU) category, which itself belongs to the embedded IC / semiconductor hierarchy. They are designed for deterministic, low-power, low-cost control tasks. The PIC16F15385T-I/MV specifically belongs to the full-featured 28/40/44/48-pin sub-tier of the PIC16F153XX family, distinguished by the highest peripheral density in the series. Key features include 4 PWM modules, a 5-bit DAC, comparators, a Configurable Logic Cell (CLC) block (4 instances), a Complementary Waveform Generator (CWG), 2 EUSART, SPI, and I2C communication peripherals, plus Core Independent Peripherals (CIPs) that offload tasks from the CPU. The integrated 10-bit ADC with Intelligent Analog capability eliminates many external analog components, while the XLP nanoWatt technology enables battery-powered applications with sleep currents measured in nanoamperes. Architecturally, the device uses a 14-bit instruction word with a modified Harvard architecture, providing predictable instruction timing and tight C code generation through Microchip's XC8 compiler. The 32MHz internal oscillator and the form-factor-matched pinout (48-UQFN with exposed pad for thermal dissipation) make it suitable for compact industrial designs. Typical applications include IoT sensor nodes, industrial control interfaces, low-power wireless sensor hubs, consumer appliance control boards, LED lighting controllers, and battery-powered instrumentation. The combination of CIPs and XLP enables designs where the CPU sleeps most of the time and peripherals autonomously service interrupts. Designers should note that the 48-UQFN package requires careful PCB layout with a thermal pad connected to ground for proper heat dissipation, and the exposed pad must be soldered for mechanical reliability. Use MPLAB X IDE with the XC8 compiler for development, and choose PIC16F15386 for higher pin count or PIC16F15376 for cost-down variants in the same family.

Angebot Kontakt

PIC16F15385T-I/PT

PIC16F15385T-I/PT - 8-Bit 32MHz MCU, 14KB Flash, 48-TQFP | Microchip

The Microchip Technology PIC16F15385T-I/PT is a member of the PIC16(L)F153xx 8-bit microcontroller family, featuring 14KB (8K x 14 words) of Flash program memory, 1KB of RAM, and a 32 MHz internal oscillator core housed in a 48-pin TQFP package with 7x7 mm body. The device operates across a wide 2.3V to 5.5V supply range and integrates Intelligent Analog peripherals, Core Independent Peripherals (CIPs), and eXtreme Low-Power (XLP) technology for battery-friendly designs. An 8-bit MCU (microcontroller) is a single-chip computer that combines a CPU, memory, and programmable I/O on one die; the PIC16 family uses a Harvard RISC architecture with separate program and data buses, executing one instruction per clock cycle to deliver deterministic real-time performance. The PIC16F15385 sits in the hierarchy: 8-bit PIC MCU -> enhanced mid-range core -> PIC16F153xx family -> Microchip's broad PIC portfolio. It supports both 5V and 3.3V system rails and includes nanoWatt XLP sleep modes with currents in the microamp range, making it attractive for mains- or battery-powered sensor nodes. Key features include four 10-bit PWMs with complementary waveform generation, a 5-bit DAC, a comparator, a 10-bit ADC with automatic channel scanning, a Complementary Waveform Generator (CWG), four Configurable Logic Cells (CLC) for hardware state-machine glue logic, two EUSART ports, and SPI/I2C interfaces. Up to 44 I/O pins are available, alongside an on-board voltage reference and multiple timer/counter modules. The integrated CIPs offload tasks from the core, reducing code complexity and lowering active-mode power. Architecturally the device pairs the enhanced mid-range core (49 instructions, 16-level hardware stack) with peripheral pin select (PPS), allowing most digital peripherals to be routed to any I/O. The 32 MHz Fosc supports a 125 ns instruction cycle, and the on-chip 32 MHz HFINTOSC eliminates an external crystal in many designs. XLP sleep currents below 1 uA (typical) support long-life battery installations such as wireless sensor transmitters and metering endpoints. Typical applications include IoT sensor nodes, home appliances, LED lighting controllers, low-power industrial sensor conditioning, and consumer white-goods user-interface boards. The combination of CLC, CWG, and PWM also suits motor-control signal generation, digital lighting, and Class-D audio modulation. Designers routinely choose this part when integrating signal-chain analog, comms, and deterministic timing without the cost of a 32-bit MCU. A key design consideration is the TQFP-48 land pattern: it requires standard surface-mount reflow and provides better thermal dissipation than smaller QFN variants, but the exposed-pad variant is not used here - ground/power are routed through dedicated pins. For applications needing >14KB Flash or more RAM, the PIC16F15386 in the same TQFP-48 footprint provides 28KB Flash and 2KB RAM and is a true drop-in upgrade. This page synthesizes distributor stock, parametric comparison, and pin-compatible alternatives not consolidated in the manufacturer datasheet, with all specifications traced to the Microchip PIC16F15385 datasheet and current distributor listings.

Angebot Kontakt

PIC16F15386-E/MV

PIC16F15386-E/MV - 28KB Flash 8-bit MCU 48-UQFN | Microchip

The Microchip Technology PIC16F15386-E/MV is an 8-bit PIC microcontroller from the PIC16(L)F153XX family, featuring 28KB of Flash program memory, 2KB of RAM, and a maximum CPU speed of 32 MHz. It is housed in a 48-pin UQFN (6x6x0.5mm) package with an exposed pad and is designed for low-power and general-purpose embedded applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and programmable peripherals. The PIC16F15386 belongs to the 8-bit MCU category, meaning its data path and arithmetic logic unit operate on 8-bit words. 8-bit MCUs sit below 16-bit and 32-bit microcontrollers in the embedded hierarchy but above simple discrete logic, offering a balance of cost, deterministic performance, and code density. PIC microcontrollers use a Harvard RISC architecture with separate program and data buses, enabling single-cycle instruction execution. Key features include four 10-bit PWM modules, a 5-bit DAC, comparators, a complementary waveform generator (CWG), four configurable logic cells (CLCs), two EUSARTs, and SPI/I2C communication peripherals. The device supports Core Independent Peripherals (CIPs) that operate without CPU intervention, reducing firmware complexity and power consumption. eXtreme Low-Power (XLP) technology provides sleep currents in the nanoamp range, making the part suitable for battery-powered applications. The 28KB Flash provides ample headroom for application firmware, while 2KB RAM supports data tables, command processing, and stack depth for complex state machines. The 48-UQFN (6x6mm) exposed-pad package provides strong thermal performance for the device class and supports compact PCB layouts in space-constrained designs. Typical applications include low-power IoT sensor nodes, consumer appliances, industrial control, LED lighting controllers, and battery-powered instrumentation. The combination of XLP, CIPs, and rich analog peripherals also suits the part to smart home devices, motor control loops, and human-machine interface (HMI) subsystems. When designing with the PIC16F15386, ensure the exposed pad is soldered to the PCB ground plane for proper thermal and electrical performance. A 100 nF decoupling capacitor should be placed as close as possible to the VDD pin to mitigate digital switching noise. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet alone, giving engineers a complete decision profile for the PIC16F15386-E/MV.

Angebot Kontakt

PIC16F15386-I/PT

PIC16F15386-I/PT - 8-bit 32MHz 28KB Flash XLP MCU | Microchip

The Microchip Technology PIC16F15386-I/PT is an 8-bit PIC XLP microcontroller running up to 32 MHz with 28 KB (16K x 14) Flash program memory, 2 KB SRAM and 256 bytes EEPROM, housed in a 48-pin TQFP (7x7 mm) package. It operates from 2.3 V to 5.5 V across the -40 C to +85 C industrial temperature range, exposing up to 43 general-purpose I/O pins for sensor-hub and human-machine-interface designs. What is an 8-bit PIC microcontroller? An 8-bit PIC microcontroller is a single-chip computer built around a RISC CPU with an 8-bit data path, on-chip Flash program memory, SRAM, EEPROM, and a configurable peripheral mix. The PIC16F153xx family sits within the larger PIC MCU hierarchy: PIC16 -> PIC mid-range -> 8-bit MCU -> microcontroller -> embedded semiconductor. The 'F' suffix denotes Flash program memory, and the 'XLP' badge identifies parts designed for eXtreme Low Power applications including sleep currents in the nanoamp range and active currents well under 1 mA/MHz. Key differentiating features of the PIC16F15386 include Core Independent Peripherals (CIPs) such as four Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), and a Numerically Controlled Oscillator (NCO) that execute logic, waveform generation, and counting without CPU intervention. The on-chip 10-bit ADC with Computation (ADC2) automates averaging, threshold comparison, and burst accumulation, while four PWMs, two comparators, a 5-bit DAC, two EUSARTs, SPI, and I2C round out the analog and digital peripheral mix. Architecturally the part pairs the standard PIC16 enhanced mid-range core with nanoWatt XLP power-management blocks including IDLE and DOZE modes, peripheral module disable, and a windowed watchdog timer. The internal 32 MHz high-speed oscillator eliminates the need for an external crystal in many designs, and the 48-pin TQFP footprint exposes a rich set of communication and timer resources. Typical applications include low-power IoT sensor nodes, battery-powered consumer appliances, LED lighting controllers, industrial sensor interfaces, remote controls, wearables, and small segment LCD subsystems. The combination of CIPs and XLP also suits it for energy-harvesting endpoints where the CPU can remain in sleep while peripherals operate. When designing with this MCU, place the ICSPDAT/ICSPCLK traces away from switching lines and provide a 100 nF decoupling capacitor close to each VDD pin plus a bulk 1-10 uF capacitor on the main rail. For deterministic motor or LED timing, configure the CWG and a 10-bit PWM in hardware so the CPU can stay in sleep, extending battery life by 10-100x compared with firmware-timed alternatives. This page synthesizes distributor pricing, same-family and drop-in cross-brand alternatives, and practical design notes that are not collected in any single manufacturer or distributor resource, giving engineers a faster path from part selection to qualified PCB layout.

Angebot Kontakt

PIC16F15386T-I/MV

PIC16F15386T-I/MV - 32MHz 8-bit MCU, 28KB Flash 48-UQFN | Microchip

The Microchip Technology PIC16F15386T-I/MV is an 8-bit PIC16 microcontroller from the PIC16F153xx XLP family, offering 28KB (16K x 14 words) of Flash program memory, 2KB SRAM, and a 32MHz internal oscillator core, housed in a 48-pin UQFN (6x6 mm) package with exposed thermal pad. The device integrates intelligent analog peripherals including a 10-bit ADC, a 5-bit DAC, comparators, and Core Independent Peripherals (CIPs) such as Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), and four PWM channels, alongside dual EUSART, SPI, and I2C communication interfaces. An 8-bit microcontroller (MCU) is a single-chip processor with an 8-bit data bus that integrates CPU, RAM, non-volatile program memory, and peripheral interfaces in one package. Within the broader taxonomy, PIC16F parts belong to the PIC microcontroller family -> 8-bit MCU -> embedded controller -> semiconductor IC, and they are designed for low-power and cost-sensitive embedded applications. The PIC16F15386T-I/MV uses a RISC architecture with a 14-bit instruction word and 32MHz maximum clock speed, balancing deterministic interrupt response with low active and sleep current consumption for XLP battery-powered designs. Key features include XLP technology for sub-microamp sleep currents, 4 Configurable Logic Cells (CLC) for hardware state-machine replacement, a Complementary Waveform Generator (CWG) for half-bridge and full-bridge drive, two EUSART modules supporting RS-232/RS-485 LIN, 28KB self-programmable Flash with device information area (DIA) and unique device ID, and 2KB SRAM. The 48-UQFN (6x6) package reduces board footprint while the exposed pad provides a low theta-JA thermal path for sustained industrial temperature operation from -40C to +85C. The architecture pairs a mid-range PIC16 core with the Peripheral Pin Select (PPS) crossbar, which lets digital peripherals be remapped to almost any I/O pin, simplifying PCB layout and BOM optimization. The CIPs let timing-critical functions run without CPU intervention, freeing the core to stay in low-power sleep states and directly improving battery life in IoT and sensor-node designs. Typical applications include IoT sensor nodes, battery-powered home automation, industrial control and HMI panels, LED lighting controllers with CWG-driven dimming, and automotive body-control accessories. The combination of 28KB Flash and 2KB RAM suits mid-complexity state machines and protocol bridges where low sleep current is essential. When designing with the PIC16F15386T-I/MV, allocate adequate GND vias under the exposed thermal pad to meet the datasheet thermal resistance specification and to provide a stable reference for the ADC. Place the 0.1uF VDD decoupling capacitor within 1-2 mm of each power pin to suppress switch-mode noise from the CWG or PWM outputs. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found on the manufacturer datasheet cover page, giving procurement and embedded engineers a single decision-ready reference.

Angebot Kontakt

Unterkategorien

Produkte (38.000+)

PIC16F15375-I/MV - 14KB Flash, 32MHz 8-bit MCU, 40-UQFN | Microchip

PIC16F15375-I/PT - 8-Bit 32MHz 14KB Flash XLP MCU | Microchip

PIC16F15375T-I/ML - 14KB Flash 8-Bit MCU, 44-QFN | Microchip

PIC16F15375T-I/MV - 8-bit MCU, 14KB Flash, 40-UQFN | Microchip

PIC16F15375T-I/PT - 14KB Flash 8-bit MCU | Microchip

PIC16F15376-E/ML - 8-bit MCU, 28KB Flash, 44-QFN | Microchip

PIC16F15376-E/MV - 8-Bit MCU, 32MHz, 28KB Flash, 40-UQFN | Microchip

PIC16F15376-E/P - 8-bit MCU, 28KB Flash, 40-PDIP | Microchip

PIC16F15376-E/PT - 32MHz 28KB Flash 8-bit MCU | Microchip

PIC16F15376-I/ML - 8-bit 32MHz 28KB Flash MCU | Microchip 44-QFN

PIC16F15376-I/MV - 32MHz 8-bit MCU, 28KB Flash, 40-UQFN | Microchip

PIC16F15376-I/P - 8-Bit MCU, 32MHz, 28KB Flash, 40-PDIP | Microchip

PIC16F15376-I/PT - 8-Bit 32MHz 28KB Flash MCU | Microchip

PIC16F15376T-I/ML - 8-bit 32MHz 28KB Flash MCU 44-QFN | Microchip

PIC16F15376T-I/MV - 28KB Flash 8-bit MCU | Microchip | XLP

PIC16F15376T-I/PT - 8-bit 32MHz MCU 28KB Flash 44-TQFP | Microchip

PIC16F15376T-I/PTVAO - 8-bit 32MHz 28KB Flash MCU | Microchip

PIC16F15385-E/MV - 8-bit MCU, 14KB Flash, 32MHz, 48-UQFN | Microchip

PIC16F15385-I/PT - 8-Bit 32MHz 14KB Flash MCU 48-TQFP | Microchip

PIC16F15385T-I/MV - 8-bit MCU, 14KB Flash, 48-UQFN | Microchip

PIC16F15385T-I/PT - 8-Bit 32MHz MCU, 14KB Flash, 48-TQFP | Microchip

PIC16F15386-E/MV - 28KB Flash 8-bit MCU 48-UQFN | Microchip

PIC16F15386-I/PT - 8-bit 32MHz 28KB Flash XLP MCU | Microchip

PIC16F15386T-I/MV - 32MHz 8-bit MCU, 28KB Flash 48-UQFN | Microchip