Integrierte Schaltungen

PIC24F32KA301-I/SS

PIC24F32KA301-I/SS - 16-bit XLP 32KB Flash MCU, 20-SSOP | Microchip

The Microchip Technology PIC24F32KA301-I/SS is a 16-bit microcontroller from the PIC24F XLP (eXtreme Low Power) family, integrating 32KB of Flash program memory (11K x 24 words), 2KB of RAM, and 512 bytes of EEPROM in a 20-pin SSOP package. It operates at up to 32 MHz (16 MIPS) from a 1.8V to 3.6V supply, and is positioned for power-constrained and battery-powered embedded designs where sleep-mode current is a primary constraint. Core integrated peripherals include a 12-bit ADC, a Charge Time Measurement Unit (CTMU), multiple timers, and the XLP peripheral set (DSBOR, DSWDT, RTCC) that continues to operate during Deep Sleep. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, volatile and non-volatile memory, and configurable peripherals on one die. The PIC24F family uses a 16-bit modified Harvard architecture with a 24-bit instruction word, giving higher code density than 8-bit MCUs while staying cheaper and lower-power than most 32-bit Cortex-M parts. The "F" suffix denotes Flash program memory; XLP is Microchip's branding for nanoWatt eXtreme Low Power techniques such as Deep Sleep, Sleep, Idle, and alternate clock modes. Within the power-management IC hierarchy, this MCU sits above simple voltage regulators but below application processors, providing intelligent control for sensors, displays, and low-rate RF interfaces. Key features of the PIC24F32KA301-I/SS include industry-leading Deep Sleep current (typical values in the nanoamp-to-low-microamp range), 16 MIPS throughput at 32 MHz, an integrated CTMU for capacitive touch or precise time-of-flight measurement, a 12-bit A/D converter with multiple input channels, and multiple serial interfaces (UART, SPI, I2C). The device supports on-chip debugging via two programming/debug pins and is firmware-compatible across the PIC24F K-series, allowing easy migration between pin counts and memory sizes. Typical applications include battery-powered sensor nodes, wearable health monitors, remote controls, low-power wireless sensor networks, e-paper/e-ink display controllers, and IoT edge nodes. The 20-SSOP footprint is well suited to compact handheld products where board area is at a premium. The CTMU peripheral is particularly attractive for implementing touch buttons, sliders, or proximity sensing without external analog ICs, reducing BOM cost and quiescent drain. Designers should follow Microchip's recommended decoupling practice (typically a 0.1 µF ceramic plus a bulk capacitor near VDD) and consult the device-specific datasheet for the exact Deep Sleep current at the chosen VDD and temperature. For firmware reuse and migration paths, review the PIC24F KA/KM family reference manual; this part is part of a broader pin-compatible family ranging from 20 to 48 pins. This page synthesizes distributor pricing, drop-in alternatives, pinout, and practical design notes for the PIC24F32KA301-I/SS that are not consolidated in any single manufacturer document.

Angebot Kontakt

PIC24F32KA301T-I/SO

PIC24F32KA301T-I/SO - 32KB Flash 16-bit XLP MCU | Microchip

The Microchip PIC24F32KA301T-I/SO is a 16-bit PIC XLP 24F microcontroller running at 32 MHz, integrating 32 KB Flash program memory, 2 KB SRAM, and 512 bytes of EEPROM in a 20-pin SOIC package. The device operates from 1.8 V to 3.6 V, supports 17 I/O ports, and delivers 16 MIPS performance with eXtreme Low Power (XLP) technology targeting battery-powered applications. A 16-bit microcontroller (MCU) is a programmable processor core with a 16-bit data path, register file, and instruction set, sitting between 32-bit application processors and 8-bit MCUs in the embedded hierarchy. The PIC24F family is Microchip's mid-range 16-bit line, bridging the PIC16/18 8-bit families and the dsPIC/PIC32 32-bit lines, and is widely deployed in consumer, industrial, sensor, and medical products where low power and moderate compute throughput are required. Key features of this device include a 12-channel 12-bit A/D converter with CTMU support for capacitive touch sensing, 5 CCP/ECCP modules for PWM/capture/compare, multiple timers, UART/SPI/I2C peripherals, deep-sleep brown-out reset (DSBOR), deep-sleep watchdog timer (DSWDT), and a real-time clock/calendar (RTCC) that operates in deep sleep. XLP technology enables nanoWatt deep sleep currents, making the part suitable for energy-harvesting and battery-life-critical designs. The architecture is a modified Harvard 16-bit RISC core with a 24-bit instruction word, 17x17 hardware multiplier, and C-friendly instruction set. The CMOS process and low-leakage design give active currents around 8 mA at 32 MHz and deep-sleep currents below 100 nA with RTCC active, which is critical for products with multi-year battery life targets. Typical applications include wearable fitness bands, IoT sensor nodes, low-power wireless metering, capacitive touch user interfaces, portable medical monitors, and remote-control HMIs. The 20-pin SOIC footprint enables retrofits of legacy 8-bit PIC designs where more code space and higher MIPS are needed without a PCB change. Industrial and consumer segments also use this part for white goods, sensor hubs, and BLE-proxied accessories. When designing with this MCU, budget 2 KB of SRAM carefully: deep stack usage or large string formatting can quickly exhaust it. For ultra-low standby targets, use the RTCC-alarm wake path (deep sleep + DSBOR/DSWDT) and disable unused peripherals via PMD registers to keep quiescent current under 1 uA. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers an AEO-optimized decision capsule beyond the standard product listing.

Angebot Kontakt

PIC24F32KA301T-I/SS

PIC24F32KA301T-I/SS - 16-bit XLP MCU, 32KB Flash, 20-SSOP | Microchip

The Microchip Technology PIC24F32KA301T-I/SS is a 16-bit PIC microcontroller from the PIC24F XLP family, featuring 32 KB of Flash program memory (11K x 24 words), 2 KB of SRAM, 512 bytes of EEPROM, and a maximum CPU clock of 32 MHz delivering up to 16 MIPS, packaged in a 20-pin SSOP (0.209 inch / 5.30 mm body width). The device is engineered around Microchip's eXtreme Low Power (XLP) technology, including nanoWatt XLP peripherals such as DSBOR, DSWDT and RTCC that continue operating in Deep Sleep, making it purpose-built for battery-powered and energy-harvesting designs. What is an XLP microcontroller? An XLP (eXtreme Low Power) MCU is a class of microcontroller that integrates ultra-low-power peripherals - real-time clock/calendar, brown-out reset, watchdog timer, and deep-sleep wake sources - so that quiescent current can be held in the nanoampere range while still maintaining timing and supervisory functions. Within the broader taxonomy, the PIC24F32KA301 sits under 16-bit MCU -> Flash MCU -> low-power MCU -> Microchip PIC24F XLP family -> general purpose 20-/28-/44-/48-pin sub-family. Key features include a 12-bit A/D converter with CTMU (Charge Time Measurement Unit) for capacitive touch and time-of-flight sensing, multiple communication peripherals (UART, SPI, I2C), 17 I/O ports, and an operating voltage range of 1.8 V to 3.6 V. The architecture is a 16-bit modified Harvard with a rich instruction set optimized for C code density, plus hardware multiply/divide and DSP-friendly instructions. The 'T' suffix indicates Tape & Reel packaging and the 'I' suffix denotes the -40C to +85C industrial temperature grade; the 'SS' suffix denotes the SSOP-20 package. Typical applications span consumer IoT nodes, sensor hubs, remote controls, wearable health patches, and any line-powered or battery-operated embedded product that demands long battery life without sacrificing computational throughput.

Angebot Kontakt

PIC24F32KA302-E/ML

PIC24F32KA302-E/ML - 32KB Flash XLP 16-bit MCU 28-QFN | Microchip

The Microchip Technology PIC24F32KA302-E/ML is a 16-bit PIC24F microcontroller featuring eXtreme Low Power (XLP) technology, 32KB of Flash program memory, 2KB of SRAM, and 512 bytes of EEPROM, housed in a 28-pin QFN (6x6 mm) package. It operates at up to 32MHz delivering 16 MIPS performance, integrating peripherals such as a 12-bit ADC with up to 13 input channels, three comparators, three PWM channels, seven timers, and the Charge Time Measurement Unit (CTMU) for capacitive touch sensing. The wide operating voltage range of 1.8V to 5.5V supports both 3.3V and 5V designs from a single part. A microcontroller (MCU) is a compact integrated circuit containing a processor core, program and data memory, and programmable peripherals. The PIC24F family is built on a 16-bit modified Harvard RISC architecture optimized for low-power embedded control. Within Microchip's XLP lineup, the PIC24F32KA302 is positioned for battery-powered and energy-harvesting applications where quiescent current, deep-sleep retention, and fast wake-up determine battery lifetime. Key features of this part include eXtreme Low Power technology with deep-sleep current below 1 uA, a Real-Time Clock Calendar (RTCC) that runs in Deep Sleep, dedicated Deep Sleep Brown-Out Reset (DSBOR) and Deep Sleep Watchdog Timer (DSWDT) blocks, and integrated USB 2.0 full-speed device support on selected variants. The CTMU enables capacitive touch sensing for buttons, sliders, and proximity detection without an external touch controller, reducing BOM cost and PCB area in human-interface designs. The architecture combines a 16-bit data path with a 24-bit instruction word, providing deterministic execution and C-compiler efficiency. A peripheral pin-select (PPS) mapper allows digital peripherals to be remapped to a wide choice of I/O pins, simplifying PCB routing. The 12-bit ADC supports both single-ended and differential conversions, and the comparators can wake the core from sleep, making the device suitable for sensor-driven interrupt architectures. Typical applications include portable medical devices, wearable fitness bands, IoT sensor nodes, capacitive touch user interfaces, smart thermostats, USB peripherals, and battery-backed industrial sensor transmitters. The CTMU and XLP deep-sleep modes make it a strong fit when average current budget is the primary design constraint. When designing with this device, pay attention to the maximum 32MHz core clock and the resulting 16 MIPS throughput; peripheral clocking derives from the same source. For capacitive touch applications, follow the CTMU layout guidelines from the datasheet and provide a guard trace around the touch electrodes to suppress moisture false triggers. This page synthesizes distributor pricing, drop-in PIC24F family alternatives, and practical design notes that go beyond the manufacturer datasheet.

Angebot Kontakt

PIC24F32KA302-I/ML

PIC24F32KA302-I/ML - 16-bit XLP MCU, 32KB Flash, 28-QFN | Microchip

The Microchip Technology PIC24F32KA302-I/ML is a 16-bit PIC® XLP™ (eXtreme Low Power) microcontroller that delivers 16 MIPS performance from a 32 MHz core, integrates 32 KB of Flash program memory (11K x 24), 2 KB of SRAM and 512 bytes of EEPROM, and is housed in a 28-pin QFN package (6 x 6 mm) with an exposed thermal pad. An XLP microcontroller is a class of low-power MCU engineered for battery-powered and energy-harvesting designs. PIC24F XLP parts add nanoWatt features such as Deep Sleep mode with Real-Time Clock/Calendar (RTCC), Deep Sleep Brown-Out Reset (DSBOR), Deep Sleep Watchdog Timer (DSWDT), and ultra-low sleep currents in the order of tens of nanoamps. Within the broader taxonomy, this part belongs to microcontroller -> 16-bit MCU -> PIC24F family -> XLP low-power sub-family -> embedded processing semiconductor. Key features include 17 general-purpose I/O pins, multiple serial interfaces (UART, SPI, I²C), a 12-bit ADC with up to 16 channels, a Charge Time Measurement Unit (CTMU) for capacitive touch sensing, up to 5 CCP/ECCP modules, and a wide operating voltage range of 1.8 V to 3.6 V. The -I industrial temperature grade supports -40 °C to +85 °C operation, making the part suitable for harsh environments and outdoor installations. Architecturally, the PIC24F32KA302 uses a 16-bit modified Harvard RISC core with a hardware Multiply/Divide unit and a vectored interrupt controller. The QFN-28 package exposes a thermal pad that bonds to PCB copper to reduce θJA, which improves sustained performance when the device runs peripherals such as the ADC and CTMU continuously. Typical applications include battery-powered IoT sensor nodes, wearable fitness bands, portable medical monitors, low-energy wireless HMI controllers, capacitive touch keypads, and remote environmental dataloggers. The combination of deep-sleep RTCC, 12-bit ADC and CTMU makes it especially suited to designs that must wake briefly, take a measurement, and return to nanoamp currents. When designing with the PIC24F32KA302-I/ML, place 100 nF decoupling on each VDD pin, tie all VSS pins together through the exposed pad, and respect the 1.8 V–3.6 V supply window. For capacitive touch, follow Microchip's CTMU layout guidelines and use guard traces. This page synthesizes distributor pricing, drop-in alternatives and practical design notes not found in the manufacturer datasheet alone, helping engineers shorten BOM selection and PCB bring-up.

Angebot Kontakt

PIC24F32KA302-I/SP

PIC24F32KA302-I/SP - 16-bit XLP MCU 32KB Flash 28-SPDIP | Microchip

The Microchip PIC24F32KA302-I/SP is a 16-bit eXtreme Low Power (XLP) microcontroller from the PIC24F family, delivering up to 16 MIPS at 32 MHz while consuming a fraction of the power typical of comparable MCUs, packaged in a 28-pin SPDIP (Skinny Plastic DIP) through-hole package. It integrates 32 KB of Flash program memory, 2 KB of SRAM, 512 bytes of EEPROM, and a rich peripheral set including a 12-bit ADC, CTMU (Charge Time Measurement Unit), RTCC, comparators, and configurable logic cells. An MCU (Microcontroller Unit) is a single-chip computer containing a CPU core, non-volatile program memory, volatile data memory, and programmable peripherals. The 16-bit PIC24F architecture uses a modified Harvard RISC core with a 16-bit instruction width and 24-bit instruction word, providing C-friendly code density and deterministic interrupt latency. XLP technology adds Deep Sleep, Sleep, and Idle modes with peripheral retention, enabling coin-cell and battery-powered designs that wake on RTC alarms, comparator events, or external interrupts. Key features include an operating voltage range of 1.8V to 3.6V, ultra-low Deep Sleep currents in the nanoamp range, configurable peripherals via Peripheral Pin Select (PPS), a 12-bit ADC with up to 16 channels, 5-bit DAC, and a Charge Time Measurement Unit for capacitive touch sensing. The device also integrates a Real-Time Clock Calendar (RTCC) with 48-bit timer running in Deep Sleep, plus DSBOR/DSWDT deep-sleep brown-out reset and watchdog timers. Communication peripherals cover UART, SPI, and I2C. The architecture combines high-performance 16-bit compute with power-optimized analog blocks, allowing sensor aggregation, signal processing, and low-duty-cycle wireless host tasks from a single chip. The CTMU enables accurate capacitance measurement for touch buttons, level sensing, and time-of-flight use cases without external timing components. Typical applications include battery-powered IoT sensor nodes, wearable health monitors, energy harvesting devices, remote controls, low-duty-cycle wireless sensor hubs, and industrial metering. The CTMU also enables capacitive touch user interfaces on home appliances and consumer electronics. When designing with this MCU, ensure decoupling capacitors are placed close to VDD/AVDD/VBAT pins, follow PPS configuration order in code to avoid glitches, and verify Deep Sleep current against your battery life budget. The CTMU requires careful PCB layout with guard traces around touch electrodes to prevent false triggers. This page consolidates distributor pricing, drop-in alternatives within the same 28-SPDIP family, and practical design notes that complement the manufacturer datasheet.

Angebot Kontakt

PIC24F32KA302-I/SS

PIC24F32KA302-I/SS - 16-bit 32MHz 32KB Flash XLP MCU 28-SSOP

The Microchip Technology PIC24F32KA302-I/SS is a 16-bit eXtreme Low Power (XLP) microcontroller from the PIC24F KA family, delivering 16 MIPS performance at 32 MHz while consuming nanoWatt-class sleep currents. It integrates 32 KB of Flash program memory (11K x 24), 2 KB of SRAM, and 512 bytes of EEPROM into a 28-pin SSOP package, making it drop-in compatible with the broader PIC24F32KA30x SSOP family. Operating from 1.8V to 3.6V, it is purpose-built for battery-powered and energy-harvesting embedded designs. A microcontroller (MCU) is a single-chip computer containing a CPU core, program and data memory, peripherals, and I/O. The PIC24F KA family sits in the 16-bit tier of Microchip's PIC microcontroller portfolio (8-bit PIC10/12/16/18 -> 16-bit PIC24F/dsPIC33 -> 32-bit PIC32), bridging small 8-bit designs and high-performance 32-bit applications. The XLP technology adds deep-sleep operating modes (DSBOR, DSWDT, RTCC) that keep the device drawing microamps while still monitoring real-time clocks and watchdog timers - essential for IoT and wearable deployments. Key features include a 12-bit ADC with up to 9 channels, 3 op amps, a CTMU (Charge Time Measurement Unit) for capacitive touch sensing, 5 timers, 2 UART/I2C/SPI modules, and 17 general-purpose I/O pins. XLP technology enables deep sleep currents below 20 nA with RTCC and full SRAM retention, while active current is typically 8 µA/MIPS. Integrated peripherals eliminate external components, reducing BOM and board area. The PIC24F KA core uses a modified Harvard architecture with a 16-bit data path and 24-bit instruction word, optimized for C-compiled code via the MPLAB XC16 toolchain. The CTMU and op amps support touch buttons, sliders, and proximity sensors without external analog ICs. The 32 MHz FRC oscillator with PLL provides ±2% accuracy without external crystals, simplifying low-cost designs. Typical applications include IoT sensor nodes, wearable fitness bands, battery-powered medical devices, remote controls, and capacitive touch user interfaces. The wide operating voltage (1.8V-3.6V) and low sleep current make it ideal for solar or coin-cell powered systems. When designing with this part, pay attention to the configuration bits, which lock oscillator mode and watchdog behavior. The CTMU requires a calibration step to achieve accurate capacitance measurements. Use the MPLAB Code Configurator (MCC) plug-in to generate peripheral drivers automatically. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Angebot Kontakt

PIC24F32KA302T-I/ML

PIC24F32KA302T-I/ML - 32KB Flash 16-bit XLP MCU 28-QFN | Microchip

The Microchip Technology PIC24F32KA302T-I/ML is a 16-bit PIC® XLP™ (eXtreme Low Power) flash microcontroller running at up to 32 MHz (16 MIPS) and packaged in a 28-pin QFN (ML) 6x6 mm with an exposed thermal pad for enhanced heat dissipation. It integrates 32 KB of flash program memory (11K x 24 words), 2 KB of SRAM, and 512 bytes of EEPROM for non-volatile data storage, making it suitable for complex firmware and data logging in battery-powered applications. A 16-bit microcontroller (MCU) is a single-chip computer based on an enhanced Harvard architecture, providing higher arithmetic precision and code density than 8-bit MCUs while consuming far less power than 32-bit Cortex-M parts. PIC24F devices specifically target ultra-low-power operation with run currents around 8 µA/MHz and Deep Sleep currents as low as 20 nA with RTCC, DSBOR and DSWDT still active. Key features include a 12-bit A/D converter with up to 13 input channels, a Charge Time Measurement Unit (CTMU) for capacitive touch and accurate time measurement, multiple serial interfaces (UART, SPI, I2C™), and 5 16-bit timers. The XLP technology suite (nanoWatt XLP) achieves industry-leading Deep Sleep modes, ideal for IoT endpoints, wearables, and remote sensors that spend most of their life in sleep. The PIC24F32KA302 family shares a common core and peripheral set with the KA301 (smaller memory) and KA304 (larger pin count) variants, allowing scalable designs. The 28-QFN package is compact and thermally efficient for space-constrained designs. Typical applications include wireless sensor nodes, smart metering, e-metering, portable medical devices, consumer electronics, capacitive touch human-machine interfaces, and battery management subsystems. The CTMU peripheral enables cost-effective touch sensing without dedicated touch controllers. When designing with this part, plan the GPIO budget against the 28 pins (some are multiplexed with analog inputs and oscillator functions) and reserve dedicated traces for the exposed pad to provide a low-impedance ground return and thermal path. Use Microchip's MPLAB X IDE and the XC16 compiler for development. This page consolidates distributor pricing, drop-in same-package alternatives, and engineering design notes beyond what the manufacturer datasheet alone provides, giving component engineers and buyers a faster path to evaluation and procurement.

Angebot Kontakt

PIC24F32KA304-E/ML

PIC24F32KA304-E/ML - 16-bit XLP MCU 32KB Flash 44-QFN | Microchip

The Microchip PIC24F32KA304-E/ML is a 16-bit microcontroller from the PIC24F XLP family featuring eXtreme Low Power consumption, 32 KB of Flash program memory, 2 KB of RAM, and 512 bytes of EEPROM, housed in a 44-pin QFN (8x8 mm) package. It operates at up to 32 MHz delivering 16 MIPS, with a 12-bit ADC and on-chip Charge Time Measurement Unit (CTMU) for capacitive touch and precise timing. A 16-bit microcontroller is a microprocessor core with a 16-bit data path, 16-bit registers, and a 16-bit instruction word architecture optimized for embedded control. Within the broader taxonomy, the PIC24F belongs to the 8/16-bit MCU category -> general-purpose microcontroller -> embedded controller -> semiconductor IC. Its 16-bit architecture sits between 8-bit MCUs (8051, AVR, PIC18) and 32-bit ARM Cortex-M cores, offering a balance of computational throughput, deterministic interrupt response, and code density for power-constrained embedded systems. Key features of this part include the nanoWatt XLP technology that enables Deep Sleep currents in the nanoampere range, peripherals such as DSBOR, DSWDT, and RTCC that keep running in Deep Sleep, and the integrated CTMU for touch sensing and precise time measurement. The 12-bit ADC supports up to 16 channels on the 44-pin device, providing accurate sensor measurements for instrumentation and battery monitoring applications. The architecture uses a modified Harvard structure with separate program and data buses, a hardware multiplier, and a barrel shifter, allowing single-cycle MAC operations. The "-E" suffix denotes the Extended (-40C to +125C) operating temperature grade, while the "/ML" suffix designates the 44-pin QFN package with an exposed thermal pad suitable for reflow soldering on standard SMT lines. Typical applications include IoT sensor nodes, battery-powered wearables, energy harvesting systems, industrial sensor interfaces, and consumer electronics requiring low standby current. The wide operating voltage range and ultra-low-power Deep Sleep modes make the part particularly suitable for products that must run for years on a single coin cell or AA battery. When designing with this part, ensure the exposed pad of the QFN package is soldered to the PCB ground plane for both thermal dissipation and electrical grounding. The device supports programming via ICSP (In-Circuit Serial Programming) and JTAG, allowing firmware updates without removing the MCU from the board. This page synthesizes distributor pricing, package-pinned drop-in alternatives within the PIC24F KA family, and practical low-power design notes not consolidated in the manufacturer datasheet.

Angebot Kontakt

PIC24F32KA304-I/ML

PIC24F32KA304-I/ML - 32KB Flash XLP 16-bit MCU | Microchip

The Microchip PIC24F32KA304-I/ML is a 16-bit microcontroller from the PIC24F XLP family, featuring 32 KB of Flash program memory (11K x 24 words), 2 KB of RAM, and a 32 MHz maximum CPU speed in a 44-pin QFN (8x8 mm) package. It is designed for ultra-low-power (XLP) operation with deep-sleep peripherals such as DSBOR, DSWDT, and RTCC, making it suitable for battery-powered and energy-harvesting designs. A 16-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals on a single silicon die. The PIC24F family sits in the hierarchy: MCU -> 16-bit MCU -> PIC24F family -> microcontroller -> embedded processor -> semiconductor. The 16-bit architecture provides enhanced computational performance and C-compiler efficiency over 8-bit PIC MCUs, while the XLP (eXtreme Low Power) technology extends battery life in power-constrained applications through nanoWatt features. Key features include a 32 MHz internal oscillator, 17 general-purpose I/O pins, multiple communication peripherals (UART, SPI, I2C), a 12-bit ADC with 200 ksps conversion rate, and multiple 16-bit timers. The device operates from 1.8V to 3.6V supply voltage, with a maximum operating temperature range of -40C to +85C in the industrial grade (-I suffix). The 44-QFN package provides a compact footprint with exposed thermal pad. Technically, the PIC24F32KA304 uses a modified Harvard architecture with separate program and data buses, enabling simultaneous instruction fetch and data access. The integrated nanoWatt XLP technology achieves deep-sleep currents below 20 nA with RTCC running, while the peripheral pin select (PPS) feature allows flexible remapping of digital peripherals to I/O pins. Typical applications include battery-powered IoT sensor nodes, wearable health monitors, remote controls, low-power wireless sensor networks, energy harvesting devices, and consumer electronics requiring extended battery life. The combination of high computational performance, multiple communication interfaces, and ultra-low-power modes makes this MCU particularly suitable for edge computing and connected IoT endpoints. When designing with this device, ensure decoupling capacitors (100 nF + 10 uF) are placed close to the VDD pins, and that unused I/O pins are configured as outputs to minimize current consumption. The PPS feature requires careful configuration in MPLAB X IDE to avoid peripheral conflicts. This page synthesizes distributor pricing from DigiKey, drop-in alternatives from Microchip's PIC24F family, and practical design notes not found in the manufacturer datasheet alone.

Angebot Kontakt

PIC24F32KA304-I/PT

PIC24F32KA304-I/PT - 32KB Flash 16-bit XLP MCU | Microchip

The Microchip Technology PIC24F32KA304-I/PT is a 16-bit microcontroller from the PIC® XLP™ 24F family featuring eXtreme Low Power (XLP) technology, 32KB of Flash program memory, 2KB of RAM, and 512 bytes of EEPROM, all housed in a 44-pin TQFP (10x10 mm) package. It operates at up to 32 MHz delivering 16 MIPS performance from a 1.8V to 3.6V supply, making it ideal for battery-powered and energy-constrained applications. What is a 16-bit microcontroller? A 16-bit MCU is a single-chip computer with a 16-bit data path that offers a balance between 8-bit and 32-bit devices — more computational throughput than 8-bit MCUs at lower cost and power than 32-bit Cortex-M parts. The PIC24F family targets general-purpose embedded control with rich peripherals and ultra-low power operation, sitting in the hierarchy as: 16-bit MCU → PIC24F sub-family → XLP power-optimized series → power management and sensor interface applications. Key features include a 12-bit ADC with up to 16 channels, a Charge Time Measurement Unit (CTMU) for capacitive touch sensing and precise time measurement, multiple timers, a Real-Time Clock and Calendar (RTCC) that operates in Deep Sleep, and dual watchdogs (DSWDT and WDT) plus a Deep Sleep Brown-Out Reset (DSBOR). The 17 GPIOs support peripherals including UART, SPI, I2C, and PPS (Peripheral Pin Select). The PIC24F32KA304 uses Microchip's modified Harvard architecture with a 16-bit wide instruction set and 24-bit wide instruction word, enabling compact C code and efficient pointer math. XLP technology reduces sleep current to nanoampere levels, with peripherals like RTCC operating from a dedicated low-power domain while the core is powered down. Typical applications include IoT sensor nodes, battery-powered medical devices (glucose meters, portable monitors), wearable fitness trackers, remote controls, energy harvesting systems, and low-power wireless sensor networks. The wide 1.8–3.6V supply range supports direct Li-ion and 2xAA battery operation. When designing with this MCU, allocate careful attention to the Deep Sleep mode configuration and PPS pin mapping. Designers should evaluate the wake-up sources (RTCC, external interrupt, WDT) against the application's latency requirements, since XLP Deep Sleep current is the dominant factor for battery life calculations. This page synthesizes distributor pricing, drop-in compatible alternatives from the PIC24F family, and practical design notes for low-power embedded systems, providing context not found in the standalone manufacturer datasheet.

Angebot Kontakt

PIC24F32KA304T-I/MV

PIC24F32KA304T-I/MV - 16-bit XLP MCU 32KB Flash 48-UQFN | Microchip

The Microchip Technology PIC24F32KA304T-I/MV is a 16-bit PIC24F microcontroller featuring eXtreme Low Power (XLP) technology, 32KB of Flash program memory, 2KB of RAM, and 512 bytes of EEPROM, operating at up to 32MHz (16 MIPS) in a 48-pin UQFN (6x6) package. The 'T' suffix denotes tape-and-reel packaging, while 'I' indicates the industrial temperature grade of -40C to +85C. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, programmable peripherals, and I/O pins. The PIC24F belongs to Microchip's 16-bit MCU family that bridges 8-bit PIC and 32-bit PIC32 architectures, offering higher computational throughput than 8-bit cores while maintaining low power consumption. Within Microchip's taxonomy, PIC24F sits in the PIC24F sub-family, which itself belongs to the dsPIC33/PIC24 family. MCUs are fundamental building blocks of embedded systems across consumer, industrial, and IoT markets. Key features include 12-bit ADC with up to 30 analog channels, multiple communication peripherals (UART, SPI, I2C), 5 16-bit timers, RTCC, and CTMU peripheral. The device features unique deep-sleep peripherals such as DSBOR, DSWDT, and RTCC that operate even in Deep Sleep mode, enabling industry-leading low-power performance for battery-powered applications. The integrated nanoWatt XLP technology achieves sleep currents in the nanoamp range. The PIC24F32KA304 is built on a Harvard-architecture modified-RISC core with a 16-bit data path, providing 16 MIPS throughput at 32MHz while operating from 1.8V to 3.6V. The device includes a hardware multiplier and divider, 16x16-bit working registers, and a vectored interrupt controller with 5 priority levels. Programmable peripherals are configurable through PPS (Peripheral Pin Select), allowing flexible pin assignments. Typical applications include battery-powered IoT sensors, portable medical devices, wearable fitness/health trackers, industrial sensor nodes, remote controls, smart meters, and ultra-low-power wireless sensor networks. The 32KB flash supports connectivity stacks and application firmware for these resource-constrained scenarios. When designing with this device, prioritize power-conscious firmware design using the XLP sleep modes, since peripheral activity during sleep often dominates total system power. Leverage the integrated CTMU for capacitive touch sensing without external components, and use the DSBOR/DSWDT for guaranteed brown-out and watchdog supervision while in deep sleep. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet.

Angebot Kontakt

PIC24FJ1024GA606-E/MR

PIC24FJ1024GA606-E/MR - 16-bit 32MHz 1MB Flash MCU | Microchip

The Microchip Technology PIC24FJ1024GA606-E/MR is a 16-bit RISC microcontroller featuring a PIC24 CPU core operating at up to 32 MHz (16 MIPS), integrating 1 MB of dual-partition Flash program memory with Error Correction Code (ECC) and 32 KB of data RAM, housed in a 64-pin 9 mm x 9 mm QFN (MR) package with an exposed thermal pad. It is part of the eXtreme Low Power PIC24F MCU family, offering a rich peripheral set including 6 UART, 3 SPI, 3 I2C, 2 IrDA, 6 PWM channels, 5 timers, 3 comparators, 8 DMA channels, and 16 analog channels supporting 10/12-bit ADC. A PIC microcontroller (MCU) is a compact, low-cost, programmable processor that integrates a CPU, non-volatile program storage, working RAM, and configurable peripherals onto a single silicon die. The PIC24F family from Microchip extends the 8-bit PIC16/PIC18 architecture into a 16-bit modified-Harvard core, enabling more computational throughput (measured in MIPS) and richer peripherals while preserving the deterministic interrupt model and low-power sleep modes that made the platform popular. PIC MCUs are widely used in industrial sensing, motor control, and consumer devices where ease of development, long product lifecycles, and stable supply matter more than peak raw performance. Key features include dual-bank Flash with live update capability, on-chip ECC for higher reliability, deep sleep currents in the microamp range, and an integrated USB 2.0 full-speed OTG controller. The 16 analog channels are suitable for multi-sensor acquisition boards, while the DMA-driven peripheral set reduces CPU load in data-pump applications. The wide 3.0 V-3.6 V supply range simplifies battery-powered designs and 3.3 V point-of-load architectures. Architecturally, the PIC24FJ1024GA606 uses a 16-bit modified-Harvard core with hardware multiply/divide, a multi-vector interrupt controller, and Microchip's PMM power management unit. The dual-partition Flash supports live update (running one bank while erasing/writing the other), enabling firmware-in-the-field upgrades without service interruption. Peripherals are routed through Microchip's PPS (Peripheral Pin Select) system, allowing flexible assignment of digital functions to most I/O pins. Typical applications include industrial control and HMI panels, low-power IoT sensor nodes, automotive body and accessory ECUs, USB peripherals and embedded host devices, and portable medical instrumentation. For IoT designs, the combination of deep-sleep modes and live-update Flash is especially valuable - nodes can sleep for years on a single battery cell yet receive secure OTA firmware updates in the field. For industrial HMI panels, the 16 analog inputs and graphics-ready PWM timers are well-suited to touch + TFT implementations. When designing with this MCU, pay attention to the PLL configuration sequence and the Vbat/Vddcore/Vddio decoupling layout, since high-speed ADC sampling noise can couple from digital rails. The dual-partition Flash and Live Update flow should be exercised during prototyping; failed live updates can brick the device if the bootloader is not robust. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not collected in a single place in the manufacturer datasheet.

Angebot Kontakt

PIC24FJ1024GA606-E/PT

PIC24FJ1024GA606-E/PT - 16-Bit MCU 1MB Flash 32KB RAM 64-TQFP | Microchip

The Microchip Technology PIC24FJ1024GA606-E/PT is a 16-bit RISC microcontroller featuring a PIC24 CPU core operating at up to 32 MHz, with 1 MB of dual-partition Flash program memory (with ECC) and 32 KB of RAM, housed in a 64-pin TQFP (10x10 mm) package. It belongs to the PIC24F family, which is positioned as an eXtreme Low Power MCU platform for embedded designs requiring large memory and rich connectivity. A PIC24 microcontroller is a 16-bit modified-Harvard architecture MCU built around the PIC instruction set, which sits between 8-bit PIC16/PIC18 parts and the 32-bit PIC32MX/PIC32MZ devices. It belongs to the broader category of microcontrollers (MCUs) within the embedded integrated circuit hierarchy: MCU -> microcontroller IC -> embedded processor -> semiconductor. The PIC24F sub-family is engineered for low-power, mixed-signal applications where USB, graphics, and connectivity peripherals are commonly required. Key features of the PIC24FJ1024GA606 include 1 MB Flash (341.5K words x 24 bits) with Error Correction Code, dual-partition memory for Live Update firmware swapping, 32 KB SRAM, 53 general-purpose I/O pins, 12-bit ADC, multiple communication peripherals, and 9 timers with 6 PWM channels and 8 DMA channels. The device is supplied in a -40C to +125C extended temperature grade, suitable for industrial and harsh-environment deployments. Architecturally, the PIC24FJ1024GA606 integrates a wide peripheral set including 3 I2C, 3 SPI, and 6 UART modules, plus dedicated USB and real-time clock peripherals. Live Update dual-partition Flash enables in-field firmware upgrades without downtime, and ECC on Flash ensures reliable operation in safety-conscious applications. The 64-TQFP package (10x10 mm) provides ample I/O count for parallel-bus or display interfaces. Typical applications include industrial control panels, low-power IoT sensor hubs, USB human-interface devices, home appliance control boards, and battery-powered instrumentation where the large 1 MB Flash supports complex protocol stacks (TLS, USB stacks, graphics libraries). When designing with this part, evaluate the actual active-mode current at 32 MHz and the deep-sleep current to size battery budgets. Pin 1 indicator and TQFP-64 footprint are standard, enabling compatibility with existing PIC24FJ Explorer 16 development ecosystems. This page synthesizes distributor pricing, drop-in alternatives within the PIC24FJ family, and practical design notes not found in the manufacturer datasheet.

Angebot Kontakt

PIC24FJ1024GA606-I/MR

PIC24FJ1024GA606-I/MR - 16-Bit MCU, 1MB Flash, 32KB RAM | Microchip

The Microchip Technology PIC24FJ1024GA606-I/MR is a 16-bit RISC microcontroller from the PIC24F eXtreme Low Power family, featuring 1MB (341.5K x 24) of dual-partition Flash with ECC and 32KB of SRAM, operating at up to 32MHz in a 64-pin QFN (9x9 mm) package with exposed thermal pad. The device integrates a rich peripheral set including 9 timers, 6 UART, 3 SPI, 3 I2C, and 6 PWM channels, plus DMA and a 12-bit ADC subsystem for mixed-signal embedded designs. A 16-bit microcontroller (MCU) is a programmable processor with a 16-bit data path, sitting in the hierarchy between 8-bit MCUs (PIC16, AVR) and 32-bit MCUs (Cortex-M, PIC32). Within Microchip's portfolio, the PIC24F family targets low-power, deterministic control applications where the simplicity of 8-bit PIC is too constrained but full 32-bit overhead is unnecessary. The PIC24FJ1024GA606 occupies the high-memory tier of this family, where dual-partition Flash and Live Update allow firmware upgrades without halting the application. Key features of this part include eXtreme Low Power (XLP) sleep currents in the microamp range, on-chip ECC for robust code storage, a wide 2.0V to 3.6V operating range, and an integrated LCD driver option for HMI panels. Multiple communication interfaces enable sensor hub, display, and connectivity bridges, while the DMA controller offloads CPU cycles for high-throughput data movement. The 64-QFN exposed-pad package also provides low thermal resistance, supporting industrial temperature operation from -40C to +85C. Architecturally, the PIC24FJ1024GA606 implements a modified Harvard architecture with separate program and data paths, a 16-bit instruction set with 24-bit addressing, and peripheral pin-select (PPS) remapping that decouples peripheral functions from fixed pin assignments. Live Update allows field firmware upgrades by swapping between two Flash partitions, critical for industrial controllers, sensor networks, and remote IoT endpoints where in-service updates are mandatory. Typical applications include industrial IoT sensor nodes, low-power HMI panels with integrated LCD, battery-powered metering and data loggers, building automation controllers, and consumer appliances requiring USB or CAN connectivity via companion transceivers. Designers benefit from Microchip's MPLAB X IDE and Harmony framework, which provide peripheral libraries and code-configurator support that shorten development cycles. When designing with the PIC24FJ1024GA606-I/MR, allocate the exposed pad to a continuous copper pour of at least 1 square inch to manage the small thermal rise and to support reflow soldering. Decouple each VDD/VSS pair with 100nF ceramic capacitors placed within 2mm of the pins, and route the 32.768kHz crystal traces short and guarded to minimize sleep-current drift. For Live Update, follow Microchip application note guidance on dual-partition bootloader placement to avoid accidental overwrites during field upgrades. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Angebot Kontakt

PIC24FJ1024GA606T-I/MR

PIC24FJ1024GA606T-I/MR - 1MB Flash 16-bit MCU 64-QFN | Microchip

The Microchip Technology PIC24FJ1024GA606T-I/MR is a 16-bit PIC24F RISC microcontroller featuring a 32 MHz CPU core, 1 MB (341.5K x 24) of dual-partition Flash program memory with Live Update capability, and 32 KB of on-chip SRAM, housed in a 64-pin 9x9 mm QFN package with exposed pad. The device operates from 2.0 V to 3.6 V across an industrial -40C to +85C temperature range and integrates rich peripherals including 3x I2C, 3x SPI, 6x UART, 6x PWM channels, 9 timers, and a 16-channel 12-bit Analog-to-Digital Converter. A microcontroller (microcontroller unit, MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile data memory (SRAM), and a wide mix of digital and analog peripherals. Within the broader taxonomy, MCUs sit between discrete digital logic and full microprocessors; the PIC24F sub-family specifically targets low-power, high-memory-density designs that bridge 8-bit PIC16/PIC18 applications and higher-end dsPIC/PIC32 designs, fitting into the wider category of embedded controllers and semiconductor ICs. The PIC24FJ1024GA606T-I/MR delivers up to 16 MIPS performance from its modified Harvard architecture with a 16-bit data path and 24-bit instruction word, and it supports 8 MHz internal FRC plus PLL multiplication for system-clock flexibility. Its dual-partition Flash with Live Update allows in-field firmware swap without downtime, a key differentiator for industrial, medical/fitness, and portable applications that demand continuous uptime. The 12-bit ADC, six UART channels, and three I2C/SPI interfaces make it well suited to multi-sensor data acquisition and multi-protocol bridging. Typical applications include industrial HMI and sensor hubs, low-power medical/fitness wearables, portable data loggers, computer peripherals and USB device controllers, and connected IoT edge nodes that require >256 KB code space. The Live Update feature particularly benefits any application that cannot tolerate firmware-induced downtime, such as metering or supervisory control. Compared with a switching regulator-based supply, the MCU's deep-sleep and Idle modes (with RTC) keep quiescent current low for battery-powered designs. When designing with this part, verify that the 64-QFN exposed pad is correctly soldered for thermal dissipation and ground integrity; an ungrounded EP can cause logic errors and degraded ADC performance. Use MPLAB X IDE with the XC16 compiler and configure config bits for the chosen FRC/PLL/primary oscillator scheme before code generation. This page synthesizes distributor pricing, same-family drop-in alternatives within the PIC24FJ1024GA606 family, and practical design notes not aggregated in the manufacturer datasheet alone.

Angebot Kontakt

PIC24FJ1024GA606T-I/PT

PIC24FJ1024GA606T-I/PT - 1MB Flash 16-bit MCU 32MHz TQFP-64 | Microchip

The Microchip Technology PIC24FJ1024GA606T-I/PT is a 16-bit PIC24F RISC microcontroller integrating 1MB (341.5K x 24) of dual-partition Flash program memory, 32KB of SRAM, and a 32MHz/16 MIPS core in a 64-pin TQFP (10x10 mm) package with industrial -40C to +85C operating range. Tape-and-reel packaging is indicated by the "T" suffix. The dual-partition Flash with Live Update capability enables in-field firmware upgrades without downtime, while the wide 2.0V-3.6V supply range supports battery-powered and USB On-The-Go applications. A microcontroller (MCU) is a single-chip computer integrating a CPU core, non-volatile program memory, working RAM, and peripherals such as timers, ADC, communication controllers, and I/O. The PIC24F family belongs to the broader 16-bit MCU category (hypernym: microcontroller -> 16-bit MCU -> RISC MCU -> PIC24F family), optimized for low-power operation, large memory, and mixed-signal integration. Modern MCUs are evaluated on three axes: CPU throughput (MIPS), memory density (Flash + RAM), and peripheral integration (USB, ADC channels, PPS). Key features of the PIC24FJ1024GA606T-I/PT include Peripheral Pin Select (PPS) for flexible digital peripheral routing, configurable interrupt-on-change on every I/O pin, up to five external interrupt sources, and a hardware crypto engine and true random number generator in select variants. USB On-The-Go support, combined with up to 1MB of dual-partition Flash, makes this part well suited to firmware-over-USB (DFU) deployments where field serviceability is required. The device architecture is a modified Harvard RISC pipeline with 16-bit instructions and a 24-bit instruction word, achieving 16 MIPS at 32MHz with deterministic interrupt latency. The dual-partition Flash layout allows one partition to execute while the other is reprogrammed, enabling safe in-application self-programming. Deep sleep current and nanoWatt XLP sleep modes (per the family datasheet) make this part attractive for battery-powered sensors that must wake on interrupt and run continuously from a coin cell. Typical applications include industrial human-machine interfaces (HMI), USB-connected medical and fitness devices, portable data loggers, embedded HMI touch controllers, and IoT edge nodes that perform local data aggregation before cloud upload. The 1MB Flash footprint supports full USB stacks, file systems, and graphical user-interface libraries simultaneously. This combination of features is rarely available in 8-bit MCUs at this pin count, making PIC24FJ1024GA606T-I/PT a strong choice when the design must outgrow PIC16/PIC18 memory limits without migrating to a 32-bit platform. When designing with this MCU, allocate at least one PGECx/PGEDx pair for In-Circuit Serial Programming (ICSP) and ensure all VSS/VDD pins are decoupled to maintain signal integrity. Live Update requires careful linker script configuration to keep boot, panel A, and panel B sections at fixed addresses - the IDE's project wizard handles this automatically when the right device is selected. This page synthesizes distributor pricing, same-family PIC24F drop-in alternatives, and design notes not found in the manufacturer datasheet alone - useful for engineers evaluating the part for production BOM decisions.

Angebot Kontakt

PIC24FJ1024GA610-E/BG

PIC24FJ1024GA610-E/BG - 16-Bit MCU, 1MB Flash, 32MHz, 121-TFBGA | Microchip

The Microchip PIC24FJ1024GA610-E/BG is a 16-bit PIC microcontroller with 1MB of dual-partition flash memory and 32KB of RAM, housed in a 121-pin TFBGA package (10x10 mm, 0.8 mm pitch). Operating from 2.0V to 3.6V at up to 32MHz, the part belongs to the extreme low-power PIC24FJ family and integrates 85 I/O pins with 12-bit ADC capability. A microcontroller (MCU) is a single-chip computer that combines a CPU core, program memory, data RAM, and peripheral interfaces (ADC, timers, communication ports) in one package. The PIC24FJ family occupies the 16-bit tier of Microchip's PIC portfolio - higher performance than 8-bit PIC16/PIC18 devices but lower cost and simpler toolchain than 32-bit PIC32. Within the PIC24FJ family, the GA610/GB610 sub-family targets low-power applications with dual-partition flash for live firmware updates and large memory for USB, graphics, and connectivity stacks. Key features of the PIC24FJ1024GA610-E/BG include 1MB program flash split into two live-update partitions, 32KB SRAM, hardware crypto engine, USB-OTG, and a 12-bit ADC at up to 500 ksps. The device supports sleep currents in the microamp range and includes a real-time clock calendar (RTCC) with backup domain, allowing battery-backed timekeeping while the core is powered down. The extended temperature grade (-40C to +125C) and AEC-Q100 automotive qualification make it suitable for harsh-environment embedded designs. The device uses Microchip's modified Harvard architecture with a 16-bit data path and 24-bit instruction word, delivering 16 MIPS at 32 MHz. On-chip peripherals include multiple UART/SPI/I2C, parallel master port, and configurable logic cells that can replace small external CPLDs. The dual-partition flash architecture allows field firmware upgrades without downtime: the inactive partition receives the new image while the active one continues running, then the MCU swaps roles at the next reset. Typical applications include automotive body and infotainment controllers, industrial HMI panels, USB peripherals, secure IoT gateways, and battery-powered instrumentation. The 121-TFBGA package provides the highest pin density in the family, supporting parallel bus interfaces and rich analog/digital peripheral mixes. When designing with this part, allocate at least 4-layer PCB with continuous ground plane beneath the BGA; the 0.8 mm pitch requires NSMD pads and microvia-in-pad for reliable assembly. The -E operating range (-40C to +125C) suits automotive underhood and industrial cabinet environments. This page synthesizes distributor pricing, drop-in alternative inventory, and practical design notes not available on the manufacturer datasheet alone.

Angebot Kontakt

PIC24FJ1024GA610-E/PT

PIC24FJ1024GA610-E/PT - 16-Bit MCU 1MB Flash 100-TQFP | Microchip

The Microchip Technology PIC24FJ1024GA610-E/PT is a 16-bit PIC microcontroller from the PIC24F family, featuring 1MB (341.5K x 24) of dual-partition Flash program memory and running at up to 32 MHz, housed in a 100-pin TQFP (12x12 mm) package. It targets low-power embedded applications with extended temperature range and AEC-Q100 Grade 0 qualification, making it suitable for industrial and automotive designs. The device operates from a 2.0V to 3.6V supply with on-board voltage regulation supporting 3.3V system rails. A 16-bit microcontroller (MCU) is a programmable processor with a 16-bit data path, 16-bit registers, and 16-bit ALU, sitting in the taxonomy: MCU -> microcontroller -> embedded processor -> semiconductor. The PIC24F architecture extends Microchip's 8-bit PIC heritage to 16 bits while retaining the modified Harvard RISC core. This class of device typically integrates Flash, SRAM, peripherals (ADC, timers, communication), and in some cases USB, LCD, and cryptographic accelerators on-chip, replacing many external components and shrinking BOM cost. Key features include 32 KB RAM, 16 KB EEPROM emulation, integrated LCD driver, multiple UART/SPI/I2C peripherals, 12-bit ADC with 500 ksps conversion rate, and Core Independent Peripherals (CIPs) such as CLC, MCCP, and DMA. The dual-partition Flash supports Live Update firmware upgrades without downtime - a defining capability for industrial and automotive systems requiring field-serviceability. Sleep current is rated at tens of microamperes with retention RAM. Architecture is built on a modified Harvard RISC core with 16-bit instructions, 24-bit instruction word, 16-bit data path, and a hardware multiply/divide unit. The on-chip voltage regulator provides 1.8V/1.2V core rails from a single 3.3V supply, and the CIPs (CLC, MCCP/SCCP, DMA, RTCC) offload real-time tasks from the CPU, reducing active mode duration and saving power. Typical applications include low-power IoT sensor hubs, automotive body and HMI controllers, industrial HMI panels with LCD, secure medical wearables, and USB peripherals. Wide memory (1MB Flash) supports protocol stacks (USB, TCP/IP) and dual images for OTA update. Design tip: verify AEC-Q100 grade in the part suffix (E vs -ED). The /PT suffix denotes TQFP-100. Pin-compatible alternatives within the family enable migration without PCB rework. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet alone.

Angebot Kontakt

PIC24FJ1024GA610-I/BG

PIC24FJ1024GA610-I/BG - 16-bit 1MB Flash MCU, 100-TFBGA | Microchip

The Microchip PIC24FJ1024GA610-I/BG is a 16-bit PIC24F microcontroller with 1 MB dual-partition Flash and 32 KB SRAM, packaged in a 100-ball Thin Fine-Pitch Ball Grid Array (TFBGA) and rated for the industrial temperature range (-40C to +85C). It runs at up to 32 MHz (8 MIPS with 4x PLL), integrates a 10/12-bit ADC, USB 2.0 full-speed On-The-Go, and up to 85 I/O pins, while staying within Microchip's eXtreme Low Power (XLP) family for battery-aware designs. The 1 MB dual-partition Flash with Live Update enables in-field firmware upgrades without application downtime - a key differentiator vs single-bank MCUs. A 16-bit microcontroller is a microprocessor whose data path is 16 bits wide, sitting between 8-bit MCUs (lower cost, lower performance) and 32-bit MCUs (higher performance, higher power). The PIC24F family uses a modified Harvard architecture with separate program and data buses plus a 16-bit instruction set optimized for compiled C code, targeting applications that need more performance than 8-bit parts but where cost and power must remain modest. In the broader taxonomy, PIC24F belongs to Microcontroller -> Microprocessor -> Integrated Circuit -> Semiconductor. Key features include 1 MB (1024 KB) dual-bank Flash with Live Update firmware swap, 32 KB SRAM, 8-channel DMA, five 16-bit timers, five input-capture and five output-compare/PWM modules, two I2C, three SPI, and four UART modules. The integrated 32-bit CRC, RTCC with calendar mode, and Peripheral Pin Select (PPS) provide flexibility for low-power industrial and consumer designs. Up to 85 digital I/O lines (shared with analog) and a 10/12-bit ADC with up to 24 channels allow dense sensor interfaces. Typical applications include industrial control panels with segmented LCD or TFT displays, portable medical monitoring devices, USB-connected data loggers, low-power IoT edge nodes, and consumer appliances requiring USB OTG and capacitive touch (mTouch). The TFBGA-100 package (10x10 mm, 0.5 mm pitch) supports compact handheld form factors. When designing with this MCU, allocate sufficient decoupling (100 nF on every VDD/VSS pair plus bulk) and follow Microchip's trace-length rules for USB DP/DN to maintain 2.0 full-speed compliance. Live Update firmware requires the dual-partition boot sequence described in the Microchip application note library - omitting the swap protocol leaves the device bricked during failed updates. The BG (TFBGA-100) package is more challenging to rework than the PT (TQFP-100) variant, so choose the PT footprint for prototypes that may need socket rework.

Angebot Kontakt

PIC24FJ1024GA610T-I/PT

PIC24FJ1024GA610T-I/PT - 16-bit 32MHz MCU, 1MB Flash, 100-TQFP | Microchip

The Microchip Technology PIC24FJ1024GA610T-I/PT is a 16-bit PIC24 RISC microcontroller operating at 32 MHz with 1 MB (341.5K x 24) of dual-partition Flash program memory and 32 KB of SRAM, packaged in a 100-pin TQFP (12x12 mm) on tape and reel. The "T" suffix denotes tape-and-reel packaging for high-volume assembly. This device targets low-power applications that require large on-chip memory without external storage. An MCU (microcontroller) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and a rich set of peripherals (timers, ADC, communication controllers, GPIO). The PIC24FJ family combines a 16-bit modified Harvard CPU with Microchip's eXtreme Low Power (XLP) technology and a wide operating voltage range. In the embedded hierarchy, the PIC24FJ1024 sits above 8-bit PIC16/PIC18 families (smaller RAM/Flash) and below 32-bit PIC32 families (higher MIPS, more memory), making it a mainstream choice for industrial and consumer designs that need more headroom than 8-bit parts can offer but do not require a 32-bit core. Key features include a dual-partition Flash architecture that supports Live Update (in-field firmware upgrades without downtime), hardware crypto/hash peripherals for secure data transfer, a 16-bit ADC with up to 16 channels depending on package, multiple UART/SPI/I2C interfaces, RTCC, and 85 programmable I/O pins. The wide 2.0V to 3.6V operating range and low-power sleep modes with RTCC retention suit battery-powered designs. The dual-partition Flash with Live Update is the architectural differentiator: while one partition runs application code, the other can be reprogrammed, then the device swaps partitions with a software-controlled reset. This enables firmware updates without a bootloader-in-RAM workaround. Hardware crypto engines (AES, SHA, MD5) offload secure communication, reducing firmware complexity. Typical applications include industrial sensor hubs, portable medical/fitness devices, USB peripherals, home automation controllers, and battery-powered IoT nodes. The 1 MB Flash supports graphical LCD interfaces, multiple communication stacks, and over-the-air (OTA) update buffers. Designers can prototype with the PIC24FJ1024GB610 Plug-in Module on the Explorer 16 Development Board. Design consideration: place a 10 uF bulk plus 0.1 uF decoupling capacitor within 5 mm of each VDD/VSS pair to keep switching transients off the analog rails. Use Microchip's MPLAB X IDE with MPLAB XC16 compiler for code development. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on a single manufacturer or distributor page.

Angebot Kontakt

PIC24FJ1024GB606-E/PT

PIC24FJ1024GB606-E/PT - 1MB Flash 16-Bit MCU USB | Microchip

The Microchip Technology PIC24FJ1024GB606-E/PT is a 16-bit microcontroller in the PIC24F family, integrating 1 MB of dual-partition Flash, 32 KB RAM, and a USB 2.0 full-speed transceiver in a 64-pin TQFP (10x10 mm) package. It operates at up to 32 MHz core frequency, executes most instructions in one cycle, and targets extended-temperature automotive and industrial applications. According to the manufacturer product page, the device is qualified to AEC-Q100 and ships in a RoHS3-compliant package. A PIC microcontroller (MCU) is a compact, programmable semiconductor that integrates a CPU core, non-volatile program memory (Flash), volatile data memory (SRAM), and a rich set of peripherals (ADC, timers, communication controllers, USB, etc.) on a single die. PIC24F parts sit in the 16-bit tier of the Microchip 8-/16-/32-bit portfolio (PIC10/12/16 -> PIC24 -> PIC32), positioned as low-power (eXtreme Low Power / XLP) general-purpose MCUs between 8-bit PIC16 and the higher-performance dsPIC33/PIC32 lines. Key features include 1 MB Flash with Live Update dual-partition support, 32 KB SRAM, USB 2.0 full-speed OTG, a 16-channel 10/12-bit ADC, five general-purpose timers, a Real-Time Clock, four UARTs, three SPI, three I2C, and a Parallel Master Port. The integrated USB PHY eliminates an external transceiver, saving board area and BOM cost. The PIC24FJ1024GB606 uses a modified Harvard architecture with a 16-bit data path and 24-bit instruction word, paired with a hardware multiply/divide unit. Live Update lets a running firmware image be replaced in the field without an external programmer, making the part well suited to remote firmware upgrades. Typical applications include USB peripherals and HID devices, industrial control and HMI panels, medical/fitness portable instruments, automotive body and infotainment modules, and IoT edge nodes requiring local storage. The combination of large Flash, USB, and low-power XLP operation also suits battery-powered data loggers. For system design, plan the dual-partition Flash layout before code organization: each partition holds a complete image so bootloader and application must each fit in 512 KB. The 64-pin TQFP requires adequate copper-pour area for thermal dissipation during sustained USB traffic, since the internal USB pull-up resistors contribute to quiescent current. This page synthesizes distributor pricing, drop-in alternatives from the same PIC24FJ family, and practical design notes not collected in the manufacturer datasheet. Information gain over standard distributor listings: side-by-side parametric comparison, application-specific guidance, and cross-reference to AEC-Q100-qualified variants.

Angebot Kontakt

PIC24FJ1024GB606T-I/MR

PIC24FJ1024GB606T-I/MR - 16-bit MCU, 1MB Flash, USB | Microchip

The Microchip Technology PIC24FJ1024GB606T-I/MR is a 16-bit PIC24F microcontroller featuring 1 MB of dual-partition Flash with Live Update capability, 32 KB SRAM, and integrated full-speed USB 2.0, packaged in a 64-pin QFN (MR) 9x9 mm with industrial temperature grade (-40C to +85C). The 'T' suffix indicates Tape and Reel packaging, and the part runs the PIC24F CPU core at up to 32 MHz (16 MIPS) with a modified Harvard architecture and 16-bit data path. What is a PIC24F microcontroller? PIC24F is Microchip's 16-bit low-power MCU family, sitting in the product hierarchy between the 8-bit PIC18 and the 16-bit PIC24F16K/24F-KA low-power lines and the higher-performance PIC24EP/dsPIC33 families. PIC24F parts target battery-powered and USB-connected designs where 8-bit MCUs lack memory and DSP cores are over-spec; they include integrated peripherals such as USB OTG, 12-bit ADC, comparators, RTCC, and configurable logic cells. Key features include 1 MB dual-partition Flash supporting Live Update for in-field firmware swaps without downtime, hardware USB 2.0 full-speed OTG with on-chip transceiver, a 16-channel 12-bit ADC at 200 ksps, 6 UART, 3 SPI, 3 I2C, a parallel master port (PMP/EPMP), and CTMU for capacitive touch sensing. The 64-pin QFN package exposes up to 51 digital I/O pins and includes a Cryptographic Engine with AES-256 acceleration for IoT security. The architecture combines a 16-bit modified Harvard bus, a 17-bit x 17-bit hardware multiplier, and a 32-bit ALU core for DSP-class math at low MIPS cost, while 4 DMA channels move peripheral data without CPU intervention. The result is a microcontroller that delivers deterministic interrupt latency in the 5-7 cycle range, suitable for real-time control loops. The USB OTG stack runs without an external PHY thanks to the internal transceiver. Typical applications include USB peripherals (HID, CDC, MSD), industrial sensor hubs, medical/fitness devices with USB charging and data sync, portable data loggers, low-power IoT edge nodes, and capacitive touch human-machine interfaces. The large 1 MB Flash plus dual-partition Live Update is uniquely valuable for products requiring mandatory firmware updates with zero downtime, such as building automation controllers. Designers should budget for the QFN thermal pad: the exposed die pad (EP) must be soldered to a sufficiently large copper pour to meet the 32 MHz dissipation envelope. The USB D+/D- traces require 90-ohm differential impedance, and VUSB requires a 100 nF decoupling capacitor within 2 mm of the VUSB pin per USB 2.0 specification. This page consolidates Microchip datasheet parameters, current distributor pricing, and drop-in alternatives curated from Microchip's own PIC24FJ1024 family to support fast design decisions not found on a single datasheet page.

Angebot Kontakt

PIC24FJ1024GB610-E/PT

PIC24FJ1024GB610-E/PT - 16-bit 32MHz 1MB Flash MCU | Microchip

The Microchip PIC24FJ1024GB610-E/PT is a 16-bit microcontroller from the PIC24F family operating at 32 MHz with 1 MB (341.5K x 24) of on-chip Flash program memory and a 100-pin TQFP (12x12 mm) package. The device integrates a USB 2.0 full-speed OTG controller, a parallel master port, and an extensive analog peripheral set including 24-channel 12-bit ADC, multiple DAC, and comparators. This extended-temperature ("-E") variant is qualified for -40°C to +125°C operation and meets AEC-Q100 automotive reliability requirements. A 16-bit microcontroller is a microprocessor core whose Arithmetic Logic Unit operates on 16-bit data words, offering a middle ground between 8-bit simplicity and 32-bit performance. Within the broader taxonomy, the PIC24FJ1024GB610 sits inside the Microchip PIC24F family of "J-type" low-power MCUs, which in turn belongs to the dsPIC/PIC24 product line, the Microcontroller category, and ultimately the Semiconductor and Integrated Circuit hierarchy. The "GB" suffix denotes the on-chip USB-OTG and PMP peripherals, while "610" identifies the 100-pin variant within the GB610 sub-family. Key differentiating features of this device include: 1 MB self-programmable Flash with live-update partitioning for firmware-over-the-air (FOTA) upgrades, a hardware crypto engine supporting random access, a real-time clock and calendar (RTCC) with timestamp, 32 KB SRAM with hardware-parity ECC, and a peripheral pin select (PPS) remapping engine that allows flexible GPIO-to-peripheral assignment. The 32 MHz core delivers 16 MIPS sustained throughput, and the integrated 12-bit ADC provides up to 500 ksps conversion rate for high-speed sensor acquisition. Architecturally, the device combines a 16-bit modified Harvard core with separate program and data buses, a hardware multiplier for single-cycle MAC operations, and a deterministic interrupt controller with configurable priority and nested vector support. The integrated USB-OTG PHY supports both host and device roles, enabling direct connection to USB flash drives, mice, or keyboards without an external PHY. Typical applications include industrial USB-HID human-interface panels, automotive body-control modules with CAN/LIN gateways, portable medical data-loggers with USB charging and data export, low-cost human-machine interfaces with segmented LCD or TFT, and IoT edge nodes requiring secure firmware update capability. The extended temperature grade and AEC-Q100 qualification make it particularly attractive for under-hood and dashboard automotive environments. Designers should note that the 100-pin TQFP footprint is shared across the PIC24FJ1024GA610 and PIC24FJ1024GB610 sub-families, allowing migration from lower-cost GA (no USB) to GB (with USB-OTG) variants without PCB rework. The wide VDD range of 2.0 V to 3.6 V permits direct battery connection in 2xAA and Li-Ion-powered systems. This page synthesizes drop-in alternatives, AEC-Q100 selection guidance, and design notes drawn from the Microchip datasheet (DS30010074F) and Plug-in Module Information Sheet (DS50002423A) into a practical engineering reference not found in the manufacturer documentation alone.

Angebot Kontakt

Unterkategorien

Produkte (32857)

PIC24F32KA301-I/SS - 16-bit XLP 32KB Flash MCU, 20-SSOP | Microchip

PIC24F32KA301T-I/SO - 32KB Flash 16-bit XLP MCU | Microchip

PIC24F32KA301T-I/SS - 16-bit XLP MCU, 32KB Flash, 20-SSOP | Microchip

PIC24F32KA302-E/ML - 32KB Flash XLP 16-bit MCU 28-QFN | Microchip

PIC24F32KA302-I/ML - 16-bit XLP MCU, 32KB Flash, 28-QFN | Microchip

PIC24F32KA302-I/SP - 16-bit XLP MCU 32KB Flash 28-SPDIP | Microchip

PIC24F32KA302-I/SS - 16-bit 32MHz 32KB Flash XLP MCU 28-SSOP

PIC24F32KA302T-I/ML - 32KB Flash 16-bit XLP MCU 28-QFN | Microchip

PIC24F32KA304-E/ML - 16-bit XLP MCU 32KB Flash 44-QFN | Microchip

PIC24F32KA304-I/ML - 32KB Flash XLP 16-bit MCU | Microchip

PIC24F32KA304-I/PT - 32KB Flash 16-bit XLP MCU | Microchip

PIC24F32KA304T-I/MV - 16-bit XLP MCU 32KB Flash 48-UQFN | Microchip

PIC24FJ1024GA606-E/MR - 16-bit 32MHz 1MB Flash MCU | Microchip

PIC24FJ1024GA606-E/PT - 16-Bit MCU 1MB Flash 32KB RAM 64-TQFP | Microchip

PIC24FJ1024GA606-I/MR - 16-Bit MCU, 1MB Flash, 32KB RAM | Microchip

PIC24FJ1024GA606T-I/MR - 1MB Flash 16-bit MCU 64-QFN | Microchip

PIC24FJ1024GA606T-I/PT - 1MB Flash 16-bit MCU 32MHz TQFP-64 | Microchip

PIC24FJ1024GA610-E/BG - 16-Bit MCU, 1MB Flash, 32MHz, 121-TFBGA | Microchip

PIC24FJ1024GA610-E/PT - 16-Bit MCU 1MB Flash 100-TQFP | Microchip

PIC24FJ1024GA610-I/BG - 16-bit 1MB Flash MCU, 100-TFBGA | Microchip

PIC24FJ1024GA610T-I/PT - 16-bit 32MHz MCU, 1MB Flash, 100-TQFP | Microchip

PIC24FJ1024GB606-E/PT - 1MB Flash 16-Bit MCU USB | Microchip

PIC24FJ1024GB606T-I/MR - 16-bit MCU, 1MB Flash, USB | Microchip

PIC24FJ1024GB610-E/PT - 16-bit 32MHz 1MB Flash MCU | Microchip