A6263KLJTR-T - 4-Ch 100mA Linear LED Driver AEC-Q100 | Allegro
Teilenummer: A6263KLJTR-T ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $2.45 | $2,45 |
| 10 | $2.18 | $21,80 |
| 100 | $1.85 | $185,00 |
| 500 | $1.62 | $810,00 |
| 1.000 | $1.4 | $1.400,00 |
A6263KLJTR-T Übersicht
A linear LED driver (also called a linear current regulator or LED array driver) is a power-management IC that sinks a regulated DC current through one or more series LED strings. It sits hierarchically as: LED driver -> constant-current driver -> PMIC (Power Management IC) -> semiconductor. Compared with switching LED drivers, linear regulators add no EMI, no switching ripple, and no inductor, at the cost of higher dissipation when the LED forward voltage is well below the supply rail.
Key features of the A6263 include a wide 6 V to 50 V input range designed to survive 12 V automotive transients (start/stop, cold-crank, load-dump), an AEC-Q100 qualification for automotive use, integrated thermal protection, and a fault-tolerant topology that disconnects LEDs on single LED short. A single reference resistor sets the master current, simplifying BOM and layout.
Architecturally, the A6263 uses four matched current mirrors fed from a bandgap-trimmed reference; outputs are open-drain capable of pulling to VIN and each channel is independently monitored. The exposed pad on the SOIC-EP package provides a low thermal-resistance path essential for dissipating (VIN - VLED) x ILED at each output, supporting robust operation in sealed lamp modules.
Typical applications include automotive rear combination lamps, daytime running lights, interior ambient lighting, and architectural/sign illumination. It is also suited for indicator control and regulated current drive circuits where EMI-sensitive analog rails are nearby.
When designing with this device, ensure adequate copper on the exposed pad to keep junction temperature within the 150 C limit at worst-case VIN and full LED current. The fault output indicates abnormal conditions and should be wired to the host MCU or left open for standalone use.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, giving engineers a single reference for evaluation, sourcing, and PCB integration.
Drop-in-Alternativen für A6263KLJTR-T – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit A6263KLJTR-T (gleiche Bauform und Footprint) – abweichend in Number of Outputs, Package, Topology.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
A6263KLJTR
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
A6263KLJTR-1
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
A6217KLJTR-1-T
✅ Drop-In✓ Auf Lager
$0.43 / Stück
Datenblatt ansehen →A6263KLJTR-T Grenzwerte & elektrische Eigenschaften
| Topologie | Linear, Constant Current |
| Anzahl der Ausgänge | 4 |
| Output Current per Channel | 100 mA (max) |
| Total LED Drive Current | 400 mA (max) |
| Eingangsspannungsbereich | 6 V to 50 V |
| Output Current Accuracy | 5% |
| Channel-to-Channel Matching | < 10% |
| Dimming | Yes (linear via IREF) |
| Internal Driver | Yes |
| Current Set Resistor | Single external reference resistor |
| Protection Features | Thermal shutdown, LED short detection |
| AEC-Q100 Qualification | Yes (automotive grade) |
| Betriebstemperaturbereich | -40 C to +150 C (junction) |
| Gehäuse | 8-pin SOIC with Exposed Pad (LJ), 3.90 mm |
| Montageart | Surface Mount |
| Packaging | Tape & Reel (TR) |
| Lead-Free / RoHS | Compliant |
A6263KLJTR-T Pin-Konfiguration
| Pin 1 | VCC — Input supply voltage (6 V to 50 V) |
| Pin 2 | OUT1 — Current output, channel 1 (up to 100 mA) |
| Pin 3 | OUT2 — Current output, channel 2 (up to 100 mA) |
| Pin 4 | OUT3 — Current output, channel 3 (up to 100 mA) |
| Pin 5 | OUT4 — Current output, channel 4 (up to 100 mA) |
| Pin 6 | IREF — Reference current set resistor |
| Pin 7 | GND — Ground |
| Pin 8 | FAULT/Thermal — Fault flag and thermal pad connection |
Typische Anwendungen
A6263KLJTR-T ist geeignet für 6 Anwendungs: Automotive Rear Combination Lamps, Daytime Running Light (DRL) Module, Automotive Interior Ambient Lighting, Industrial 24 V LED Strip Driver, Signage and Channel Letter Illumination, Indicator and Status LED Arrays.
Automotive Rear Combination Lamps
The A6263KLJTR-T is ideal for automotive rear combination lamps where brake, tail, turn, and reverse functions are implemented as 4 separate LED strings. Each of the 4 outputs can drive a 100 mA string independently with 5% accuracy and better than 10% channel-to-channel matching, eliminating the need for ballast resistors. The 6 V to 50 V input range survives 12 V automotive transients including cold-crank, start/stop, and load-dump events, while the AEC-Q100 qualification validates the part for under-hood and exterior lamp modules with junction temperatures up to 150 C. The integrated thermal shutdown and LED short detection protect the lamp module against field failures.
Empfohlen
Daytime Running Light (DRL) Module
The A6263KLJTR-T suits DRL modules where multiple LED strings are driven in parallel for redundancy and uniform brightness. With 400 mA total drive capability across 4 channels and linear topology, no switching EMI is introduced into adjacent RF receivers (keyless entry, AM/FM, satellite). The exposed pad (EP) on the SOIC package provides the low thermal resistance needed to dissipate (VIN - VLED) * ILED at each output, allowing sealed automotive lamp designs without external heatsinking. AEC-Q100 qualification and 50 V load-dump tolerance meet automotive reliability requirements for exterior lighting.
Empfohlen
Automotive Interior Ambient Lighting
The A6263KLJTR-T drives multi-color interior ambient lighting with 4 independent channels per IC. Each output controls a separate LED color (typically red, green, blue, white) enabling smooth color mixing and dimming via the IREF reference current. The 4-channel architecture reduces component count versus discrete single-channel drivers, simplifying PCB layout in door-panel, dashboard, and footwell modules. Linear topology eliminates inductor audible noise (a concern in quiet cabin environments), while AEC-Q100 qualification and 50 V load-dump tolerance cover the full automotive electrical environment.
Empfohlen
Industrial 24 V LED Strip Driver
The A6263KLJTR-T is suitable for industrial 24 V LED strip and architectural lighting applications where 4 independent constant-current channels are needed. The wide 6 V to 50 V input range accommodates 24 V industrial supply buses with significant transient headroom. The 100 mA per channel capability (400 mA total) supports typical LED strip currents, and the linear topology avoids the EMI that switching drivers would inject into nearby industrial sensors and control circuitry. The exposed pad SOIC package enables compact PCB designs with adequate thermal dissipation.
Empfohlen
Signage and Channel Letter Illumination
The A6263KLJTR-T drives LED modules in signage and channel letter applications where 4 channels control different letter zones or colors. The single reference resistor simplifies current setting during signage installation and repair - technicians only adjust one resistor for the entire module. The 50 V input tolerance protects against supply transients in outdoor signage fed by long wiring runs. AEC-Q100 qualification, while automotive-targeted, also provides extended reliability margin for outdoor commercial signage with temperature swings from -40 C to +85 C ambient.
Empfohlen
Indicator and Status LED Arrays
The A6263KLJTR-T is well-suited for status indicator panels where 4 LEDs per IC indicate system states (power, fault, activity, ready). The 5% current accuracy and 10% channel matching ensure uniform brightness across indicators, important for professional equipment appearance. The wide input range (6 V to 50 V) accepts power directly from 12 V or 24 V system rails without pre-conditioning. The exposed-pad SOIC package allows hand-soldering-friendly assembly for low-volume industrial equipment where automated placement may not be available.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für A6263KLJTR-T – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | A6263KLJTR | A6263KLJTR-1 | A6217KLJTR-1-T |
|---|---|---|---|---|
| Brand | Allegro MicroSystems | Allegro MicroSystems | Allegro MicroSystems | Allegro MicroSystems |
| Package | 8-SOIC-EP (LJ) | 8-SOIC-EP (LJ) - same | 8-SOIC-EP (LJ) - same | 8-SOIC-EP (LJ) - same |
| Number of Outputs | 4 | 4 | 4 | 1 |
| Output Current per Channel | 100 mA | 100 mA | 100 mA | 1.5 A |
| Input Voltage Range | 6 V to 50 V | 6 V to 50 V | 6 V to 50 V | 6 V to 50 V |
| Topology | Linear | Linear | Linear | Linear |
| AEC-Q100 | Yes | No (commercial) | No (extended industrial) | Yes |
| Channel Matching | < 10% | < 10% | < 10% | N/A (single channel) |
| Current Set Resistor | Single external | Single external | Single external | Single external |
Wichtigste Unterscheidungsmerkmale
- AEC-Q100 qualified for automotive applications (vs. A6263KLJTR (non-automotive grade))
- 4 independent 100 mA channels in single 8-pin SOIC-EP (vs. A6217KLJTR-1-T (single channel 1.5 A))
- Linear topology with no EMI (vs. Switching LED drivers)
Designhinweise
Estimated: At VIN = 13.5 V (automotive nominal) and 4 strings of 3 white LEDs at 100 mA each with VLED_total = 9 V, power dissipation is (13.5 - 9) * 0.4 = 1.8 W. The 8-SOIC-EP package requires at least 100 mm^2 of copper pour on the exposed pad to maintain junction temperature below 125 C at 85 C ambient. Insufficient copper is the most common field failure mode for linear LED drivers - always validate thermal performance on the final PCB layout before committing to production.
Place the IREF reference resistor as close to pin 6 as possible to minimize noise pickup and ground-loop errors. Use a 1% tolerance resistor to maintain the 5% output current accuracy specified in the datasheet. The exposed pad must be soldered to a continuous copper plane on top and bottom layers, stitched with thermal vias, to provide the low thermal resistance path required for reliable operation. Decouple VCC with a 1 uF X7R ceramic capacitor placed within 5 mm of pin 1.
Do not exceed 50 V on VCC even transiently - load-dump pulses above 50 V can permanently damage the device. If the application is connected directly to the automotive battery without transient suppression, add a TVS diode rated for 36 V working voltage to clamp load-dump pulses. Do not leave unused output pins floating - connect them to GND or to an active output to prevent fault conditions. The IREF pin must not exceed 6.5 V per the datasheet absolute maximum rating.
Compliance-Informationen
AEC-Q100 qualified for automotive applications. RoHS and REACH compliant per Allegro product page. Lead-free and halogen-free per package materials declaration.
