AD9615BH - 1-Circuit Operational Amplifier | Analog Devices
Teilenummer: AD9615BH ✓ AktivAD9615BH Übersicht
An operational amplifier is an active semiconductor component used to amplify voltage differences in analog signal chains. The category includes single and multiple amplifier configurations, and it sits within the broader hierarchy of analog integrated circuits, signal-conditioning electronics, and semiconductor devices. Operational amplifiers are commonly used in sensor interfaces, signal buffers, gain stages, filtering circuits, and instrumentation systems. The AD9615BH is identified as a single operational amplifier, so one package provides one amplifier circuit and requires separate circuitry if multiple independent channels are needed.
The available component information highlights current-feedback architecture and wideband frequency compensation as preferred architectural characteristics for the AD9615BH. These features distinguish it from slower general-purpose voltage-feedback devices when signal bandwidth, rise behavior, or feedback-network design is important. The listed maximum input offset voltage of 1600 uV provides the primary stated input-referred accuracy parameter, while the 148 mA maximum supply current identifies the upper stated supply-current specification. The operational amplifier category and single-circuit organization make the device suitable for focused analog signal-conditioning blocks rather than highly integrated multichannel systems.
AD9615BH is packaged with 12 terminals in a QIP configuration and is described as a through-hole component with a square package shape. The “BH” ordering suffix identifies the specific package and temperature-grade configuration within the AD9615 family, but the manufacturer datasheet should be consulted for exact lead numbering, maximum ratings, common-mode range, slew rate, bandwidth, and recommended operating conditions. The listed part classification identifies the component as one operational amplifier circuit, so designers should verify that the 12-terminal package does not imply 12 independent amplifier channels.
Typical uses for this device include current-sensor signal conditioning, where an amplifier can scale a small sensor voltage before conversion or control, and buffered instrumentation inputs, where drive capability and low offset help preserve the integrity of a measured signal. The part can also be used in wideband analog gain stages, active filter signal paths, and industrial measurement interfaces. In each case, feedback component selection and board layout remain central to stable operation, particularly because current-feedback amplifiers generally require different resistor relationships from voltage-feedback amplifiers.
For a new layout, begin by confirming the AD9615BH pinout, power-supply limits, common-mode input range, and recommended decoupling in the manufacturer datasheet. Place the supply bypass capacitor close to the device power pins, keep feedback-loop copper short, and provide a low-impedance return path. Because the listed maximum supply current is 148 mA, power-budget calculations should include amplifier quiescent current, load current, and the operating supply voltage rather than assuming that package current alone determines dissipation.
Drop-in-Alternativen für AD9615BH – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Für dieses Produkt sind keine Drop-in-Alternativen verfügbar.
Alternativen anfordernAD9615BH Grenzwerte & elektrische Eigenschaften
| Amplifier Type | Operational Amplifier |
| Number of Circuits | 1 circuit |
| Architecture | Current Feedback |
| Compensation | Wideband frequency compensation |
| Maximum Supply Current | 148 mA |
| Maximum Input Offset Voltage | 1600 uV |
| Number of Terminals | 12 terminals |
| Terminal Form | Through-hole |
| Package Code | QIP |
| Package Shape | Square |
| Temperature Grade | Other |
| Montageart | Through-hole |
AD9615BH square Pinbelegungsleitfaden
Pinbelegung für AD9615BH (square-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.
Keine detaillierten Pinbelegungsdaten verfügbar für AD9615BH.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
AD9615BH ist geeignet für 6 Anwendungs: Current-Sensor Signal Conditioning, Precision Instrumentation Buffer, Wideband Active Filter Stage, Industrial Sensor Interface, Audio and Communication Gain Stage, Analog Control Loop.
Current-Sensor Signal Conditioning
The AD9615BH can amplify the small voltage produced by a current sensor before the signal reaches an ADC or controller. Its current-feedback architecture and wideband frequency compensation suit wideband analog paths, while the listed 1600 uV maximum input offset voltage provides a key accuracy checkpoint when the sensor signal is small. The amplifier is used as one gain stage between the sensing element and the conversion chain. Verify the sensor's common-mode voltage, required bandwidth, feedback-network values, and the AD9615BH input and output limits before finalizing the circuit.
Precision Instrumentation Buffer
The AD9615BH is applicable to buffered instrumentation inputs where a sensor, bridge, or measurement node requires amplification before further processing. Its single-circuit organization permits one amplifier to be allocated to each independent analog channel, and the stated 1600 uV maximum input offset voltage is the main listed measure of input-referred error. Use it as the first gain or buffering stage and keep the feedback network close to the device. Confirm input bias current, common-mode range, noise, and drift against the measurement accuracy budget.
Wideband Active Filter Stage
The AD9615BH can serve as the active gain element in a wideband filter signal path because the part is identified with current-feedback architecture and wideband frequency compensation. This makes it relevant to designs in which a passive filter alone cannot provide the required gain or input impedance. Component values must follow the feedback topology and stability guidance in the manufacturer datasheet rather than generic voltage-feedback equations. Check the resulting magnitude and phase response across the complete frequency range, and account for the 148 mA maximum supply-current specification in the power design.
Industrial Sensor Interface
The AD9615BH fits an industrial sensor interface when the required signal bandwidth and input range are compatible with the amplifier. Its through-hole, 12-terminal QIP construction supports boards where a mechanically robust leaded package is preferred, and its current-feedback architecture is useful for amplified sensor signals. The design must verify operating temperature, supply voltage, common-mode range, and output swing because those limits are not stated in the component listing. Provide local supply bypassing and a low-impedance ground return to preserve signal integrity.
Audio and Communication Gain Stage
The AD9615BH can be evaluated for a communications or audio gain stage where wideband frequency compensation is important and the circuit operates within the amplifier's input and output limits. Its single-circuit package allows separate devices to be used for different channels without relying on a multi-amplifier package. Current-feedback compensation values must be selected using the manufacturer guidance, because incorrect feedback resistors can cause peaking or instability. Confirm slew rate, output drive, noise, and distortion requirements from the datasheet before using the part in a signal-quality-critical path.
Analog Control Loop
The AD9615BH can be used in an analog control loop to amplify an error or feedback signal before driving a downstream comparator, actuator interface, or control input. The current-feedback architecture supports wideband compensation, while the 12-terminal through-hole package can simplify assembly on through-hole industrial control boards. Stability and phase margin must be evaluated with the actual feedback network, load, and compensation capacitors. Validate the 148 mA maximum supply-current limit and the 1600 uV maximum input offset voltage against the control-loop error budget.
Technische Referenzdaten für AD9615BH – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Designhinweise
Confirm the exact AD9615BH lead numbering from the manufacturer pin-description table before routing the PCB. The part is identified as a 12-terminal through-hole QIP package, but package outline similarity does not guarantee identical pin functions across amplifier families. Keep the op-amp input, feedback, and output paths short, and provide a continuous ground plane to reduce parasitic feedback through shared impedance.
Use the listed 148 mA maximum supply current as an upper-level power-budget checkpoint, not as a constant operating-current assumption. Calculate dissipation from the actual supply voltage and total device current, then confirm that the PCB and through-hole package can remove the resulting heat. Place the supply bypass capacitor adjacent to the device power pins and connect it directly to the return plane for effective high-frequency bypassing.
Do not copy feedback-resistor values from a voltage-feedback amplifier into the AD9615BH circuit. The AD9615BH is identified as a current-feedback device with wideband frequency compensation, and its stable gain network must follow the manufacturer guidance. Also verify the 1600 uV maximum input offset voltage against the required measurement accuracy, since offset can dominate the error budget in low-level sensor interfaces.
Compliance-Informationen
The component information identifies the AD9615BH as a current-feedback operational amplifier in a 12-terminal through-hole QIP package. Compliance and qualification details require confirmation from the manufacturer product documentation or declaration.