ADC0848BCVX - 8-Bit 8-Ch Microprocessor-Compatible ADC | TI
Teilenummer: ADC0848BCVX ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $6.5 | $6,50 |
| 10 | $5.85 | $58,50 |
| 100 | $5.2 | $520,00 |
| 500 | $4.65 | $2.325,00 |
| 1.000 | $4.1 | $4.100,00 |
ADC0848BCVX Übersicht
A successive-approximation ADC (SAR ADC) is a type of data converter that determines each bit of the digital output by binary-searching the analog input against an internal DAC and comparator. SAR ADCs sit in the broader hierarchy: ADC -> data converter -> signal chain IC -> mixed-signal semiconductor. The ADC0848 family occupies the classic 8-bit, low-speed, multi-channel data-acquisition niche, offering deterministic latency and ease of microprocessor interfacing that pipelined and delta-sigma ADCs typically sacrifice.
Key features include software-configurable single-ended, differential, or pseudo-differential input modes, an on-chip sample-and-hold, ratiometric or absolute voltage reference operation, and a microprocessor-compatible parallel interface with read/write control lines. The 28-PLCC (FN) J-lead package is a plastic-leaded chip carrier that provides easy prototyping and socket compatibility while exposing enough thermal pad area for the modest dissipation of this CMOS device.
The ADC0848 uses a switched-capacitor successive-approximation architecture built on a CMOS process, which keeps power consumption low (typically well under 10 mW) and eliminates the need for an external negative supply. The differential input mode enables common-mode noise rejection in industrial environments where long sensor runs pick up 50/60 Hz interference, while pseudo-differential mode simplifies PCB layout for ground-referenced sensors.
Typical applications include industrial process-control analog front-ends, multi-channel sensor multiplexing in factory automation, panel-meter and instrumentation data acquisition, portable battery-powered measurement devices, and legacy microprocessor-based embedded systems where deterministic conversion timing is required. The 8-channel mux eliminates external analog switches in most designs.
When designing with this part, ensure the reference pin is driven from a low-impedance source (datasheet requires >=1.1 kOhm drive capability) and place 0.1 uF decoupling close to the supply pins. For ratiometric operation, use the same excitation voltage for the sensor bridge and the VREF pin to cancel reference drift.
Drop-in-Alternativen für ADC0848BCVX – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit ADC0848BCVX (gleiche Bauform und Footprint) – abweichend in Number of Input Channels, Package, Reference Input Resistance (min), Reference Voltage, Resolution.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
ADC0848BCVX/NOPB
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ADC0848CCVX
✅ Drop-In✓ Auf Lager
$3.78 / Stück
Datenblatt ansehen →ADC0848CCV
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
ADC0848BCVX Grenzwerte & elektrische Eigenschaften
| Auflösung | 8 bits |
| Number of Input Channels | 8 (configurable to 4 differential) |
| Architecture | Successive Approximation (SAR) |
| Abtastrate | 25 kSPS (min), up to ~33 kSPS |
| Conversion Time (max) | 60 us |
| Data Interface | Parallel (microprocessor-compatible) |
| Input Modes | Single-ended, differential, pseudo-differential |
| Referenzspannung | 2.5 V to VCC (ratiometric or absolute) |
| Reference Input Resistance (min) | 1.1 kOhm |
| Supply Voltage (VCC) | 4.5 V to 6.0 V (typ. 5 V) |
| Betriebstemperatur | -40C to +85C (industrial) |
| Gehäuse | 28-PLCC (FN) J-lead, 11.51 x 11.51 mm |
| Pin-Anzahl | 28 |
| Montageart | Surface Mount |
| RoHS-Status | Compliant (NOPB suffix variant) |
| On-Chip Sample-and-Hold | Yes |
ADC0848BCVX Pin-Konfiguration
| Pin 1 | CH1 — Analog input channel 1 |
| Pin 2 | CH2 — Analog input channel 2 |
| Pin 3 | CH3 — Analog input channel 3 |
| Pin 4 | CH4 — Analog input channel 4 |
| Pin 5 | CH5 — Analog input channel 5 |
| Pin 6 | CH6 — Analog input channel 6 |
| Pin 7 | CH7 — Analog input channel 7 |
| Pin 8 | AGND — Analog ground |
| Pin 9 | VREF — Voltage reference input (>=1.1 kOhm drive required) |
| Pin 10 | VCC — Positive supply (4.5 V to 6.0 V) |
| Pin 11 | DGND — Digital ground |
| Pin 12 | DB0 — Data output bit 0 (LSB) |
| Pin 13 | DB1 — Data output bit 1 |
| Pin 14 | DB2 — Data output bit 2 |
| Pin 15 | DB3 — Data output bit 3 |
| Pin 16 | DB4 — Data output bit 4 |
| Pin 17 | DB5 — Data output bit 5 |
| Pin 18 | DB6 — Data output bit 6 |
| Pin 19 | DB7 — Data output bit 7 (MSB) |
| Pin 20 | /CS — Chip select (active low) |
| Pin 21 | /RD — Read strobe (active low) |
| Pin 22 | /WR — Write / conversion start (active low) |
| Pin 23 | CLK IN — Clock input |
| Pin 24 | CLK R — Clock resistor (sets internal clock frequency) |
| Pin 25 | INTR — Interrupt output (active low, signals conversion complete) |
| Pin 26 | CH0 — Analog input channel 0 |
| Pin 27 | NC — Not connected (per datasheet) |
| Pin 28 | NC — Not connected (per datasheet) |
Typische Anwendungen
ADC0848BCVX ist geeignet für 6 Anwendungs: Industrial Process Control Analog Front-End, Multi-Channel Sensor Multiplexing Data Acquisition, Panel Meter and Instrumentation Readout, Portable Battery-Powered Measurement Devices, Legacy Microprocessor-Based Embedded Systems, Automotive Sensor Interface Modules.
Industrial Process Control Analog Front-End
The ADC0848BCVX fits industrial PLC analog input modules because of its 8 single-ended (or 4 differential) input channels that eliminate external analog multiplexers, its -40C to +85C industrial temperature range per the TI datasheet, and its software-configurable differential mode that rejects common-mode noise on long sensor cable runs. With 60 us conversion time and ~25-33 kSPS throughput, it comfortably digitizes 4-20 mA loop signals, thermocouple breakouts, and pressure-transducer outputs at PLC scan rates of 10-100 Hz. Placed behind RC anti-alias filters on each CHx pin, the SAR architecture provides deterministic conversion latency that simplifies PLC ladder-logic timing.
Empfohlen
Multi-Channel Sensor Multiplexing Data Acquisition
The ADC0848BCVX's 8-channel analog multiplexer and software-programmable channel selection make it a single-chip solution for multi-transducer DAQ boards in factory automation and instrumentation. Differential input mode rejects 50/60 Hz line interference picked up on long sensor cables - critical for thermocouple and strain-gauge bridges. The ratiometric reference capability allows excitation voltage and VREF to track together, cancelling bridge excitation drift. With 25 kSPS throughput it can sequentially scan 8 channels at 3 kHz each, sufficient for vibration monitoring and slow process control loops.
Empfohlen
Panel Meter and Instrumentation Readout
Digital panel meters and bench-top multimeters benefit from the ADC0848BCVX's parallel microprocessor interface and 8-channel input mux, allowing a single ADC to read multiple measurement ranges (volts, amps, temperature) selected via the front-panel rotary switch. The 8-bit resolution provides 1 part in 256 (0.4%) accuracy - adequate for 3-digit panel-meter displays. Its 60 us conversion time updates the display faster than human perception, eliminating visible flicker. The CMOS process keeps power dissipation low, suiting battery-powered handheld instruments.
Empfohlen
Portable Battery-Powered Measurement Devices
Portable field measurement instruments use the ADC0848BCVX because its CMOS SAR architecture draws only milliwatts of supply current, extending battery life in handheld data loggers and environmental monitors. The 4.5-6.0 V single-supply operation pairs with 4 x AA alkaline or single Li-ion cell arrangements. With 8 input channels, a single ADC scans temperature, humidity, pressure, and flow sensors in weather stations and portable gas detectors. The 28-PLCC package is compact enough for handheld enclosures.
Empfohlen
Legacy Microprocessor-Based Embedded Systems
The ADC0848BCVX is designed for direct connection to 8-bit microprocessors such as the 8051, 68HC11, Z80, and similar legacy MCUs via its parallel data bus and /CS, /RD, /WR control lines. Deterministic SAR conversion timing makes software drivers straightforward - no complex FIFO or DMA management is required. Educational kits, vintage industrial controllers, and retro-computing projects benefit from the well-documented timing diagrams in the TI ADC0844/ADC0848 datasheet. The 28-PLCC package allows socketed prototyping on through-hole adapter boards.
Empfohlen
Automotive Sensor Interface Modules
While not AEC-Q100 qualified, the ADC0848BCVX is used in non-safety automotive applications such as cabin environmental sensors, battery management telemetry, and aftermarket gauge clusters. Its pseudo-differential input mode simplifies PCB layout for ground-referenced automotive sensors, while the wide -40C to +85C operating range handles underhood and cabin temperature extremes. The 8-channel mux interfaces directly with multiple sensor types (temperature, pressure, position) on a single ADC, reducing BOM cost in cost-sensitive automotive aftermarket designs.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für ADC0848BCVX – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | ADC0848BCVX/NOPB | ADC0848CCVX | ADC0848CCV | ADC0844CCN/NOPB | ADC0838CCN/NOPB |
|---|---|---|---|---|---|---|
| Package | 28-PLCC (FN) J-lead | 28-PLCC (FN) - same | 28-PLCC (FN) - same | 28-PLCC (FN) - same | 20-PDIP (N) - different | 20-PDIP (N) - different |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Resolution | 8 bits | 8 bits | 8 bits | 8 bits | 8 bits | 8 bits |
| Number of Channels | 8 single-ended / 4 differential | 8 single-ended / 4 differential | 8 single-ended / 4 differential | 8 single-ended / 4 differential | 4 single-ended / 2 differential | 8 single-ended / 4 differential (serial I/F) |
| Sampling Rate | ~25-33 kSPS | ~25-33 kSPS | ~25-33 kSPS | ~25-33 kSPS | ~25-33 kSPS | ~25 kSPS |
| Interface | Parallel | Parallel | Parallel | Parallel | Parallel | Serial (SPI/MICROWIRE) |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| RoHS Compliance | Requires NOPB suffix | Compliant | Check suffix | Check suffix | Compliant | Compliant |
Wichtigste Unterscheidungsmerkmale
- 8-channel input multiplexer eliminates external analog switches (vs. ADC0844CCN/NOPB)
- Software-configurable input modes provide design flexibility (vs. ADC0838CCN/NOPB)
- Pb-free NOPB variant available for RoHS designs (vs. ADC0848BCV (no NOPB))
- Industry-standard 28-PLCC socket-compatible package (vs. ADC0834BCN/NOPB (20-DIP))
Designhinweise
Estimated: Power dissipation is approximately P = VCC x ICC. With VCC=5V and typical ICC estimated at 5 mA based on the CMOS SAR architecture, Pdiss ~= 25 mW. Decouple VCC with a 0.1 uF ceramic capacitor placed within 5 mm of the VCC pin and a bulk 1-10 uF electrolytic on the same node. Per the TI ADC0848 datasheet, the VREF pin requires a low-impedance drive capable of at least 1.1 kOhm - use a dedicated reference IC or buffer op-amp, not a high-impedance resistive divider.
Separate analog ground (AGND, pin 8) and digital ground (DGND, pin 11) returns to a single-point star ground near the ADC to avoid digital switching noise coupling into analog inputs. Place anti-alias RC low-pass filters (typically 1 kOhm + 1 nF, fc ~160 kHz) on each CHx input close to the pin. Keep analog input traces short and away from digital output bus traces (DB0-DB7) which carry fast edges during read cycles. The 28-PLCC J-lead package allows socketed prototyping - use a Mill-Max 28-pin PLCC socket for easy replacement during firmware bring-up.
Do not drive VREF from a high-impedance source - the datasheet specifies a minimum 1.1 kOhm drive capability is required, otherwise conversion accuracy suffers. In ratiometric applications, use the same excitation voltage (typically 5V) for both the sensor bridge and VREF so that supply drift cancels. Do not leave unused analog input channels floating - tie them to AGND or a known mid-rail voltage to prevent spurious coupling. The /WR pin initiates conversion; ensure software provides adequate delay between /WR and reading DBx per the timing diagram in the TI datasheet (typically 60 us max conversion time).
The DB0-DB7 parallel outputs drive CMOS logic levels; in long-trace designs add 33-100 Ohm series damping resistors near the ADC outputs to dampen ringing on fast rising edges. The /INTR output (active low, signals end-of-conversion) should be pulled up with a 4.7-10 kOhm resistor to VCC if wired-OR'd with other interrupt sources. When using the differential input mode, ensure the common-mode voltage stays within the input common-mode range (typically AGND to VCC); exceeding it saturates the input sampling capacitor and produces erroneous conversions.
Compliance-Informationen
The non-NOPB ADC0848BCVX contains lead (Pb) in the finish and is NOT RoHS compliant; for RoHS-compliant designs use ADC0848BCVX/NOPB. Not AEC-Q100 qualified - not suitable for automotive safety applications. REACH compliance per TI product declaration.
