ADM238LANZ - 4/4 RS-232 Transceiver, 5V | Analog Devices
Teilenummer: ADM238LANZ ✓ AktivADM238LANZ Übersicht
An RS-232 transceiver is an interface IC that combines differential-to-single-ended line drivers and single-ended-to-differential receivers. It belongs to the broader hierarchy of interface ICs, communication transceivers, and semiconductors. Unlike RS-422 and RS-485 interfaces, which commonly use balanced differential signaling and multipoint arrangements, RS-232 is a single-ended, point-to-point interface designed for shorter cable connections and logic-level serialization between data-terminal equipment and data-communication equipment.
Key features include a single 5 V power supply, four integrated drivers, four integrated receivers, 120 kbps data-rate capability, small 1 μF charge-pump capacitors, and a shutdown mode that reduces supply current to 1 μA or less. The receiver inputs tolerate ±30 V, providing protection against voltage excursions encountered on an RS-232 connection. These characteristics make the ADM238LANZ useful where legacy RS-232 ports must coexist with modern low-voltage digital logic.
The on-board dc-to-dc converters generate the bipolar voltage required by RS-232 drivers from the single 5 V rail. A 1 μF capacitor is specified for each converter, while the driver side supplies approximately ±9 V output swing. The device includes four drivers and four receivers, allowing multiple serial channels to be implemented without repeating the power-conversion circuitry. Its receiver architecture supports operation with the supply rail removed when inputs remain within the specified ±30 V range.
Typical applications include industrial serial adapters, test and measurement equipment, data acquisition systems, legacy peripheral interfaces, point-of-sale equipment, and embedded-control systems that retain an RS-232 port. The integrated power conversion is especially useful where a ±12 V rail is unavailable but the logic system operates from 5 V. For each channel, the board must also provide the connector protection and signal-routing considerations appropriate to the cable environment.
Design attention should be given to charge-pump capacitor placement, grounding, and protection at the connector. Keep the 1 μF converter capacitors close to their specified pins, route RS-232 traces away from sensitive analog or high-speed digital paths, and use an appropriately rated protection network for exposed cables. The shutdown function must be controlled correctly because entering shutdown disconnects the interface and reduces supply current to 1 μA or less.
This page combines the ADM238LANZ operating characteristics, package information, sourcing guidance, interface design considerations, and a qualified drop-in comparison. It also identifies where a candidate replacement has the same 24-pin DIP footprint and where additional design verification is required before substitution.
Drop-in-Alternativen für ADM238LANZ – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit ADM238LANZ (gleiche Bauform und Footprint) – abweichend in Maximum Data Rate, Package, Supply Voltage, Product Type, Charge-Pump Capacitor.
ADM238LJNZ
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →ADM238LAN
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →MAX238CNG+
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ADM238LANZ Technische Daten
| Product Type | RS-232 transceiver |
| Driver Count | 4 drivers |
| Receiver Count | 4 receivers |
| Versorgungsspannung | 5 V |
| Maximum Data Rate | 120 kbps |
| Interface Standards | EIA-232-E and V.28 |
| Driver Output Swing | approximately ±9 V from a 5 V supply |
| Charge-Pump Capacitor | 1 μF |
| Shutdown Supply Current | ≤1 μA |
| Receiver Input Voltage Tolerance | ±30 V |
| Latch-Up Protection | Latch-up free |
| Gehäuse | 24-pin plastic DIP |
| Montageart | Through-hole |
ADM238LANZ 24-pin plastic dip Pinbelegungsleitfaden
Pinbelegung für ADM238LANZ (24-pin plastic dip-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für ADM238LANZ.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
ADM238LANZ ist geeignet für 6 Anwendungs: Industrial Serial Port Expansion, Embedded Data Acquisition Equipment, Test and Measurement Instrument, Legacy Peripheral Connectivity, Point-of-Sale Terminal, Industrial Control Panel Interface.
Industrial Serial Port Expansion
The ADM238LANZ is suitable for industrial equipment that must expose several legacy RS-232 ports while operating from a single 5 V rail. Its four drivers and four receivers permit four communication channels to share one transceiver package, while the onboard dc-to-dc converters avoid requiring a separate ±12 V supply. The verified datasheet excerpt specifies approximately ±9 V output swing, EIA-232-E and V.28 compliance, and operation up to 120 kbps. Place the specified 1 μF charge-pump capacitors close to their pins and protect each connector-facing line against external voltage transients.
Empfohlen
Embedded Data Acquisition Equipment
The ADM238LANZ fits embedded data-acquisition and laboratory-control equipment that collects data from legacy RS-232 instruments. Four receivers can monitor four incoming data streams, while four drivers support four outbound channels, allowing the controller to use one consistent 5 V supply domain. Its 120 kbps maximum data rate is suitable for many legacy control and measurement links, although cable capacitance and grounding determine the practical limit. The integrated dc-to-dc conversion simplifies board partitioning, but each external cable should include surge and ESD protection.
Empfohlen
Test and Measurement Instrument
The ADM238LANZ can serve as the multi-channel RS-232 interface in a test instrument or service controller with 5 V logic. Four full-duplex channels reduce the number of interface packages needed, and the approximately ±9 V driver swing supports conventional RS-232 equipment without a bipolar supply. The 120 kbps rate is more than sufficient for configuration commands and low-speed measurement transfer. Designers should maintain a single-point logic ground strategy, isolate connector ground from noisy power-return paths, and verify that shutdown control cannot disable the interface during an active test sequence.
Empfohlen
Legacy Peripheral Connectivity
The ADM238LANZ is a practical choice when modern control electronics must connect to legacy printers, scanners, or laboratory peripherals using RS-232. The single 5 V supply lets the interface coexist with the logic rails found in many embedded systems, while four drivers and receivers accommodate multiple peripheral ports. Its integrated dc-to-dc converters and 1 μF capacitor requirement reduce external component count compared with a discrete charge-pump design. Firmware should control baud rate and line signaling consistently, and the system integrator must verify connector pin assignments and unsupported modern RS-232 features.
Empfohlen
Point-of-Sale Terminal
A point-of-sale terminal can use the ADM238LANZ to consolidate several RS-232 connections to peripherals, scanners, or service equipment within a 5 V system. Four integrated channels reduce the footprint and power-conversion overhead associated with separate transceivers, while the low-power shutdown mode can reduce consumption when those ports are idle. The 120 kbps capability supports typical command and transaction traffic. Reliable implementation requires protected connector routes, controlled ground references, and firmware that avoids leaving individual channels enabled when the system is in its low-power state.
Empfohlen
Industrial Control Panel Interface
The ADM238LANZ can support a multi-port industrial control panel that communicates with legacy programmable controllers or service consoles. Four drivers and receivers provide enough parallel channels for several RS-232 links, and operation from a single 5 V rail simplifies power distribution inside an enclosure. Because the package is a 24-pin DIP rather than a surface-mount option, the board must provide suitable through-hole footprint clearance and mechanical support. Keep connector protection near the board edge and route the driver outputs away from sensitive analog sections to minimize coupling.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für ADM238LANZ – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | ADM238LJNZ | ADM238LAN | MAX238CNG+ |
|---|---|---|---|---|
| Package | 24-PDIP | 24-PDIP | 24-PDIP | 24-PDIP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Maxim Integrated |
| Product Type | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver |
| Driver Count | 4 drivers | 4 drivers | 4 drivers | 4 drivers |
| Receiver Count | 4 receivers | 4 receivers | 4 receivers | 4 receivers |
Wichtigste Unterscheidungsmerkmale
- Four full RS-232 channels in one package (vs. MAX238CNG+)
- Single-rail operation with integrated bipolar conversion (vs. MAX238CNG+)
- Documented low-power shutdown (vs. ADM238LAN)
- High legacy RS-232 data-rate capability (vs. ADM238LJNZ)
Designhinweise
Place the specified 1 μF charge-pump capacitors close to their associated ADM238LANZ pins and keep their return paths short. Follow the Analog Devices datasheet capacitor connection and polarity instructions exactly. Place connector-side protection components near the board edge, and provide an unobstructed ground return from the interface connector to the device ground reference.
Separate the four RS-232 driver outputs from sensitive analog and high-speed digital traces to reduce crosstalk and electromagnetic coupling. Route driver and receiver nets away from clocks, switching-regulator nodes, and high-impedance sensor inputs. Use a consistent interface-ground strategy and avoid allowing large chassis or cable currents to flow through the logic-ground region.
Do not treat every ADM238L suffix as electrically and environmentally interchangeable. Verify the ADM238LANZ temperature grade, full pinout, supply limits, and shutdown behavior in the manufacturer datasheet before releasing a PCB. Also verify that the connected RS-232 device uses compatible signal polarity and connector assignment; a physically identical DIP footprint does not guarantee identical peripheral-side pin functions.
Compliance-Informationen
No explicit RoHS, REACH, halogen-free, lead-free, or conflict-minerals declaration was identified for the exact ADM238LANZ orderable part. AEC-Q100 is not applicable to this general-purpose RS-232 interface IC.