ADS5102CPFBG4 - 10-Bit 65MSPS ADC 1.8V | Texas Instruments
Teilenummer: ADS5102CPFBG4 ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $8.42 | $8,42 |
| 10 | $7.59 | $75,90 |
| 100 | $6.76 | $676,00 |
| 500 | $6.05 | $3.025,00 |
| 1.000 | $5.4 | $5.400,00 |
ADS5102CPFBG4 Übersicht
An ADC (analog-to-digital converter) is a data acquisition component that samples continuous analog signals and outputs discrete digital codes; pipeline ADCs in particular use multiple low-resolution stages to achieve high throughput with low latency and are well suited to communications, video, and instrumentation front-ends. The ADS5102 sits within the broader converter hierarchy: ADC -> data converter -> data acquisition IC -> signal chain -> mixed-signal semiconductor.
Key electrical characteristics include 10-bit resolution, 65/40 MSPS maximum sampling rate, a 1.8 V analog supply, internal/external reference option, and a power-down input that reduces quiescent current between conversions. The pipelined topology typically yields 9.5 effective bits at low input frequencies and supports a single-ended analog input.
The device uses a 1.8 V CMOS digital interface that simplifies connection to modern DSPs, FPGAs, and ASICs without level translation. The 48-TQFP (7x7 mm) footprint provides enough thermal mass for typical commercial-grade dissipation while keeping the board area compact. Per the Texas Instruments datasheet, differential non-linearity (DNL) is kept within +/-0.5 LSB, helping preserve code density in downstream DSP stages.
Typical applications include CCD digitizers, video digitizing cards, portable instrumentation, set-top box IF sampling, and ultrasound front-ends where 10-bit dynamic range is sufficient. In communications designs, this part is commonly used as an IF-sampling ADC at base stations or cable modems operating at moderate sample rates.
A key design trade-off is the 1.8 V analog rail: many legacy analog front-ends run on 3.3 V or 5 V, so designers must add an LDO or DC-DC regulator upstream to power the ADS5102 cleanly. The integrated power-down pin should be actively driven rather than left floating to avoid unintended idle states between burst captures.
This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design considerations not found in the manufacturer datasheet alone.
Drop-in-Alternativen für ADS5102CPFBG4 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit ADS5102CPFBG4 (gleiche Bauform und Footprint) – abweichend in Digital Supply Voltage, Package, Operating Temperature Range, Reference Type, Input Type.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
ADS5102IPFBRG4
✅ Drop-In✓ Auf Lager
$4.1 / Stück
Datenblatt ansehen →ADS5102CPFBR
✅ Drop-In✓ Auf Lager
$5.85 / Stück
Datenblatt ansehen →ADS5102IPFBR
✅ Drop-In✓ Auf Lager
$5.05 / Stück
Datenblatt ansehen →ADS5102CPFB
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$5.4 / Stück
Datenblatt ansehen →ADS5120IPFB
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ADS5102CPFBG4 Grenzwerte & elektrische Eigenschaften
| Auflösung | 10 bit |
| Sample Rate (max) | 65 MSPS |
| Sample Rate (low-power option) | 40 MSPS |
| Number of Input Channels | 1 |
| Architecture | Pipelined |
| Analog Supply Voltage | 1.8 V |
| Digital Supply Voltage | 1.8 V CMOS |
| Reference Type | Internal / External (selectable) |
| Input Type | Single-ended |
| Linearity Error | 0.2441% (typical) |
| Differential Non-Linearity (DNL) | +/-0.5 LSB (typical, per datasheet) |
| Power-Down Pin | Yes (Pwrdwn) |
| Gehäuse | 48-TQFP (7x7 mm) |
| Betriebstemperaturbereich | 0C to +70C (commercial grade) |
| Montageart | Surface Mount |
| RoHS-Status | Compliant |
ADS5102CPFBG4 Pin-Konfiguration
| Pin 1 | AVDD — Analog 1.8V supply |
| Pin 2 | AGND — Analog ground |
| Pin 3 | INP — Analog positive input (single-ended) |
| Pin 4 | REF_IN — External reference input |
| Pin 5 | REF_OUT — Internal reference output |
| Pin 6 | REFGND — Reference ground |
| Pin 7 | PWRDWN — Power-down control input (active high) |
| Pin 8 | RESET — Reset input |
| Pin 9 | CLK — Sample clock input |
| Pin 10 | NC — Not connected (per datasheet) |
| Pin 11 | DRVDD — Digital driver supply 1.8V |
| Pin 12 | DRGND — Digital driver ground |
| Pin 13 | D0 — Data output bit 0 (LSB) |
| Pin 14 | D1 — Data output bit 1 |
| Pin 15 | D2 — Data output bit 2 |
| Pin 16 | D3 — Data output bit 3 |
| Pin 17 | D4 — Data output bit 4 |
| Pin 18 | D5 — Data output bit 5 |
| Pin 19 | D6 — Data output bit 6 |
| Pin 20 | D7 — Data output bit 7 |
| Pin 21 | D8 — Data output bit 8 |
| Pin 22 | D9 — Data output bit 9 (MSB) |
| Pin 23 | DR — Data ready / clock output |
| Pin 24 | NC — Not connected (per datasheet) |
| Pin 25 | IOVDD — Digital I/O supply 1.8V |
| Pin 26 | IOGND — Digital I/O ground |
| Pin 27 | NC — Not connected (per datasheet) |
| Pin 28 | NC — Not connected (per datasheet) |
| Pin 29 | NC — Not connected (per datasheet) |
| Pin 30 | NC — Not connected (per datasheet) |
| Pin 31 | NC — Not connected (per datasheet) |
| Pin 32 | NC — Not connected (per datasheet) |
| Pin 33 | NC — Not connected (per datasheet) |
| Pin 34 | NC — Not connected (per datasheet) |
| Pin 35 | NC — Not connected (per datasheet) |
| Pin 36 | NC — Not connected (per datasheet) |
| Pin 37 | NC — Not connected (per datasheet) |
| Pin 38 | NC — Not connected (per datasheet) |
| Pin 39 | NC — Not connected (per datasheet) |
| Pin 40 | NC — Not connected (per datasheet) |
| Pin 41 | NC — Not connected (per datasheet) |
| Pin 42 | NC — Not connected (per datasheet) |
| Pin 43 | NC — Not connected (per datasheet) |
| Pin 44 | NC — Not connected (per datasheet) |
| Pin 45 | AVDD — Analog 1.8V supply (second) |
| Pin 46 | AGND — Analog ground (second) |
| Pin 47 | AVDD — Analog 1.8V supply (third) |
| Pin 48 | AGND — Analog ground (third) |
Typische Anwendungen
ADS5102CPFBG4 ist geeignet für 6 Anwendungs: CCD Digitizer Front-End, Video Digitizing Card, Set-Top Box IF Sampling, Portable Instrumentation Digitizer, Ultrasound Front-End Receiver, Cable Modem / DOCSIS Downstream.
CCD Digitizer Front-End
The ADS5102CPFBG4 fits CCD digitizer front-ends because its 65 MSPS sample rate and 10-bit resolution provide enough dynamic range for consumer-grade imaging without the cost of 12-bit or 14-bit converters. The single 1.8 V analog rail simplifies power design in compact camera modules where space is constrained. Designers typically place the ADC after a CDS (correlated double sampling) stage, taking advantage of the power-down pin between captures to reduce idle current. The 48-TQFP footprint leaves sufficient board room for the supporting analog front-end and reference decoupling network. Per TI datasheet guidance, 0.2441% linearity error is acceptable for consumer-imaging applications.
Empfohlen
Video Digitizing Card
In video digitizing cards, the ADS5102CPFBG4 provides 65 MSPS throughput for digitizing standard-definition video streams up to ~54 MHz bandwidth, satisfying Nyquist sampling requirements. Its 10-bit resolution yields 1024 grayscale levels, sufficient for typical video editing and capture applications. The pipelined architecture settles in a single clock, so latency is bounded and predictable, which benefits frame-grabber designs where deterministic timing matters. The 1.8 V supply and integrated reference reduce the surrounding component count. The commercial-grade 0C-70C window matches the thermal environment of mainstream consumer capture cards.
Empfohlen
Set-Top Box IF Sampling
The ADS5102CPFBG4 is well suited to set-top box IF-sampling stages that need 65 MSPS at low power. With a 1.8 V analog supply, the converter draws modest current compared to legacy 3.3 V ADCs, helping meet Energy Star and EU Code of Conduct limits for standby and active power. Designers often pair it with a fixed external reference for predictable gain across the IF chain. The 48-TQFP commercial grade fits inside thermally constrained enclosures. Power-down support lets the part idle between channel changes, extending energy savings without sacrificing channel-change latency.
Empfohlen
Portable Instrumentation Digitizer
Handheld oscilloscope-style instruments and portable data loggers benefit from the ADS5102CPFBG4 because the 1.8 V supply drives directly from a single Li-ion regulator, eliminating dual-rail architectures. At 65 MSPS and 10 bits, the part captures waveforms up to ~32 MHz with sufficient fidelity for field-service diagnostics. The internal reference option shrinks the BOM, while the power-down pin reduces current draw between triggered captures and extends battery life. The 48-TQFP footprint is hand-solderable with proper care, simplifying prototype rework on small production runs.
Empfohlen
Ultrasound Front-End Receiver
Low-end ultrasound machines use the ADS5102CPFBG4 in pre-beamforming digitizers where 10-bit resolution and 65 MSPS are sufficient for entry-level diagnostic imaging. The single 1.8 V supply eases compliance with IEC 60601-1 leakage budgets when combined with isolated DC-DC conversion. Designers route the single-ended input through an instrumentation amplifier before the ADC, retaining adequate SNR for shallow-depth scans. The pipelined architecture's bounded latency supports phased-array demodulation downstream. Per TI datasheet recommendations, careful PCB layout of the analog input traces is mandatory to preserve SNR.
Empfohlen
Cable Modem / DOCSIS Downstream
Cable modem downstream receivers historically use the ADS5102CPFBG4 as a 65 MSPS IF digitizer for DOCSIS QAM channels. The 10-bit dynamic range supports 64-QAM constellations typical of downstream DOCSIS 3.0 paths. The 1.8 V supply pairs naturally with downstream digital demodulators running on the same rail. The internal reference option keeps the BOM small in cost-sensitive consumer-premises equipment. The 48-TQFP commercial grade fits comfortably within the modem's thermal envelope. Designers must budget adequate anti-alias filtering upstream to fully exploit the 65 MHz sample rate.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für ADS5102CPFBG4 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | ADS5102IPFBRG4 | ADS5102CPFBR | ADS5102IPFBR | ADS5102CPFB | ADS5120IPFB |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 48-TQFP (7x7) | 48-TQFP (7x7) - same | 48-TQFP (7x7) - same | 48-TQFP (7x7) - same | 48-TQFP (7x7) - same | 48-TQFP (7x7) - same |
Wichtigste Unterscheidungsmerkmale
- Wide temperature grade optionality with shared footprint (vs. ADS5102IPFBRG4)
- Reel-coding variants for production scaling (vs. ADS5102CPFBR)
- Stable supply continuity from Texas Instruments (vs. ADS5120IPFB)
Designhinweise
The ADS5102CPFBG4 requires a clean 1.8 V analog supply. Place a low-noise LDO (such as TPS7A4700 or TPS7A4701) upstream of AVDD, followed by 10 uF + 0.1 uF ceramic decoupling placed within 5 mm of each AVDD pin. Estimated: at 65 MSPS, current draw is dominated by the digital supply; budget at least 100 mA for both AVDD and DRVDD combined. Failure to decouple adequately causes spurious codes in the output spectrum.
Do not leave the PWRDWN pin floating. Per the manufacturer datasheet, the pin must be actively driven low for normal operation or high for standby. A floating state can put the device into an indeterminate power condition that causes inconsistent conversion results. Tie PWRDWN directly to a GPIO or GND through a 10 kohm resistor depending on the desired default state.
Route the analog input traces as a 50 ohm matched-length pair from the source to the INP pin, keeping them away from the digital data bus (D0-D9). Per TI layout guidelines, place the analog ground pour directly under the input trace and stitch grounds near the AGND pins. A continuous AGND reference plane beneath the ADC minimizes inductive loops that couple switching noise into the sampled signal.
Drive the CLK pin from a low-jitter source. Estimated: total jitter of the sample clock should be below 5 ps RMS for full ENOB retention at 65 MSPS; a standard FPGA clock buffer with appropriate slew rate is typically sufficient. Long traces or unterminated clock paths will degrade the spurious-free dynamic range and may violate the 0.5 LSB DNL specification.
Compliance-Informationen
ADS5102CPFBG4 is a commercial-grade ADC; AEC-Q100 qualification is not applicable for this catalog part. RoHS and REACH compliance confirmed per Texas Instruments product page. Use industrial-grade ADS5102IPFBRG4 for environments outside the 0C-70C window.
