ATF16LV8C-10JU - 10ns 16V8 EECMOS PLD | Microchip
Teilenummer: ATF16LV8C-10JU ✓ AktivATF16LV8C-10JU Übersicht
A simple programmable logic device, or SPLD, is a semiconductor that combines programmable logic gates, registers, and interconnect resources into a compact package. The ATF16LV8C belongs to the 16V8 architecture within the broader hierarchy of programmable logic devices, PLDs, and digital semiconductors. Its 8 macrocells provide a flexible way to implement combinational and registered control logic, address decoding, state machines, and interface functions without using a large gate array.
The ATF16LV8C uses electrically erasable CMOS technology based on proven electrically erasable flash memory. This architecture allows the programmed configuration to be reprogrammed rather than constrained to a one-time mask-programmed implementation. Key characteristics include a 10 ns speed grade, 8 macrocells, 250 product terms, and operation across the 3.0 V to 5.25 V range specified for industrial and commercial temperature grades. A dedicated power-down control option supports systems that need to reduce current consumption when logic activity is not required.
The 20-pin PLCC package provides a compact surface-mount form factor with J-leaded connections and a 9 x 9 mm body. Its architecture incorporates a superset of generic 16V8 arrangements and can directly replace the 16R8 family and most 20-pin combinatorial PLD devices when pin, voltage, speed, and logic requirements align. This compatibility makes the ATF16LV8C useful for repairing and redesigning legacy control systems based on GAL-type or 16V8 logic.
Typical uses include industrial controller interface logic, state-machine implementations, keyboard or panel decoding, peripheral address decoding, and compact glue-logic functions in embedded equipment. The 10 ns grade is particularly relevant where combinational path timing must be checked against clock and propagation requirements. Designers should still evaluate each product term, macrocell, register, and I/O assignment against the target system rather than assuming every 16V8 device has identical behavior.
When designing around the ATF16LV8C-10JU, preserve the 3.0 V to 5.25 V operating range, place decoupling close to the supply pins, and validate every replacement pin against the manufacturer pin description and programming software. For direct substitutions, speed-grade differences can alter timing margins, while different programmable technologies may affect configuration procedures and system behavior.
This product page combines manufacturer specifications, verified package and architecture data, drop-in candidate comparisons, and practical selection guidance. It also distinguishes genuine same-footprint replacements from devices that only match functionally, helping engineers shorten legacy PLD repair and redesign cycles without overlooking programming, timing, or package constraints.
Drop-in-Alternativen für ATF16LV8C-10JU – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit ATF16LV8C-10JU (gleiche Bauform und Footprint) – abweichend in Device Type, Package, Power-Down Current, Operating Modes, Architecture.
ATF16LV8C-10JC
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →ATF16LV8C-15JC
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →ATF16LV8C-15JU
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ATF16V8B-10JU
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →ATF16V8B-15JU
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →ATF16LV8C-10JU Grenzwerte & elektrische Eigenschaften
| Device Type | EECMOS erasable programmable logic device (SPLD) |
| Architecture | 16V8 |
| Macrocells | 8 macrocells |
| Product Terms | 250 product terms |
| Speed Grade | 10 ns |
| Supply Voltage Range | 3.0 V to 5.25 V |
| Power-Down Current | 5 uA |
| Programmable Technology | Electrically erasable flash memory based EECMOS |
| Power-Down Control | Pin-controlled |
| Gehäuse | 20-pin PLCC, 9 x 9 mm |
| Lead Style | J-lead |
| Montageart | Surface mount |
| Temperature Grades | Industrial and commercial |
| Logic Compatibility | Superset of generic 16V8 architectures |
| Legacy Compatibility | Direct replacement for 16R8 family and most 20-pin combinatorial PLDs |
ATF16LV8C-10JU 20-pin plcc, 9 x 9 mm Pinbelegungsleitfaden
Pinbelegung für ATF16LV8C-10JU (20-pin plcc, 9 x 9 mm-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für ATF16LV8C-10JU.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
ATF16LV8C-10JU ist geeignet für 6 Anwendungs: Industrial Control Interface Logic, Embedded State-Machine Control, Peripheral Address Decoding, Instrument Panel and Keyboard Decoding, Legacy PLC and Control-System Repair, Low-Power Embedded Logic.
Industrial Control Interface Logic
The ATF16LV8C-10JU is suitable for consolidating discrete control functions in industrial equipment because its 16V8 architecture provides 8 macrocells and 250 product terms. The 10 ns speed grade gives designers a defined propagation-delay target when implementing address decoding, interlock logic, or output-command sequencing. Its 3.0 V to 5.25 V operating range supports both 3.3 V and 5 V system rails. Use the PLCC version when maintaining a 20-pin legacy controller board, and validate every timing path against the system clock before release.
Empfohlen
Embedded State-Machine Control
The ATF16LV8C-10JU can implement compact state machines for appliances, test equipment, and peripheral controllers that require registered outputs and combinational transitions. Eight macrocells provide dedicated logic resources without the complexity of a larger FPGA, while the 10 ns grade supports tighter combinational timing budgets than a 15 ns alternative. The electrically erasable flash architecture permits configuration updates during development and service. Designers should map each state and output explicitly because product-term allocation and register availability constrain practical implementations.
Empfohlen
Peripheral Address Decoding
ATF16LV8C-10JU is appropriate for decoding addresses and control strobes around older processors, memories, and programmable I/O devices. The 16V8 structure combines product terms and I/O resources into one package, reducing the number of separate gates required for bank selection and chip-enable generation. A 10 ns speed rating helps preserve timing margin in address-based systems, but decode depth must remain within the device's 8-macrocell capacity. Check active-polarity conventions and registered versus combinational outputs during schematic conversion.
Empfohlen
Instrument Panel and Keyboard Decoding
The ATF16LV8C-10JU can consolidate switch-scanning, display-selection, and panel-control functions in a compact instrument. Its 8 macrocells support modest combinational and registered logic, while the 20-pin PLCC package simplifies repair of leaded legacy assemblies. The 3.0 V to 5.25 V range allows the device to operate from common instrument rails, and the pin-controlled power-down option can reduce demand when an operating mode is inactive. Confirm debounce and scan timing against the actual switch and display interface requirements.
Empfohlen
Legacy PLC and Control-System Repair
The ATF16LV8C-10JU is well suited to repairing legacy PLC-adjacent control boards built around 16V8, 16R8, or compatible 20-pin combinatorial PLDs. Its architecture is described as a superset of generic 16V8 forms, while the 10 ns grade retains useful timing performance for older control loops. The 20-pin PLCC package matches many J-lead board footprints, but replacement still requires exact pinout, polarity, and logic-equivalence checks. Preserve the original JEDEC programming file and validate every output state after installation.
Empfohlen
Low-Power Embedded Logic
ATF16LV8C-10JU can support low-power auxiliary logic when a system periodically enters a reduced-activity state. The pin-controlled power-down function is specified at 5 uA, allowing the logic device to be disabled while other circuitry remains operational. Its 3.0 V to 5.25 V supply range accommodates common embedded rails, and the 8-macrocell capacity is adequate for supervisory flags, wake sequencing, or isolated command decoding. Confirm that power-down pins remain in a valid state and that output behavior during shutdown is acceptable for the connected peripheral.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für ATF16LV8C-10JU – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | ATF16LV8C-10JC | ATF16LV8C-15JC | ATF16LV8C-15JU | ATF16V8B-10JU | ATF16V8B-15JU |
|---|---|---|---|---|---|---|
| Package | 20-PLCC (9x9) | 20-PLCC (9x9) | 20-PLCC (9x9) | 20-PLCC (9x9) | 20-PLCC (9x9) | 20-PLCC (9x9) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Series | 16V8 | 16V8 | 16V8 | 16V8 | 16V8B | 16V8B |
| Macrocells | 8 macrocells | 8 macrocells | 8 macrocells | 8 macrocells | 8 macrocells | 8 macrocells |
| Speed Grade | 10 ns | 10 ns | 15 ns | 15 ns | 10 ns | 15 ns |
Wichtigste Unterscheidungsmerkmale
- Faster nominal propagation-delay grade within the same 16V8 family (vs. ATF16LV8C-15JU)
- Active status for maintenance and redesign programs (vs. ATF16V8B-10JU)
- Flash-based electrically erasable configuration (vs. ATF16LV8C-10JC)
Designhinweise
Do not treat the phrase 16V8 as proof that every PLCC device is interchangeable. Confirm the exact pin names, power-down polarity, register configuration, and product-term architecture against the manufacturer datasheet. A 15 ns replacement may work functionally but reduces nominal timing margin by 5 ns, or 33% relative to the 10 ns target. Legacy 16V8B devices may also differ in programming behavior, so verify the configuration file and state equations before production release.
Use the manufacturer 20-pin PLCC land pattern rather than deriving a footprint from another J-lead package. Check lead pitch, body outline, and pad orientation before ordering boards. Because PLCC is not represented by a dedicated package-diagram key in the available library, verify physical orientation against the manufacturer package drawing. In repair work, inspect existing pads for corrosion, bridging, or heat damage before installing the replacement device.
Keep the supply rail within the specified 3.0 V to 5.25 V operating range and place bypass capacitors close to the supply and ground pins. The ATF16LV8C family includes a pin-controlled power-down option specified at 5 uA, but actual system consumption also includes leakage and any external pull networks. Ensure the power-down control cannot float, and verify that connected outputs enter an acceptable state whenever the device is disabled.
Create a timing budget for every combinational path using the 10 ns device grade and the applicable system-clock requirements. Do not assume that equal macrocell counts produce identical propagation delay between 16V8 implementations. Check output polarity, registered-output clocking, feedback-path structure, and reset expectations in the programming software. For legacy conversions, compare the original schematic and programming file line by line before enabling the replacement in service.
Compliance-Informationen
No definitive compliance declarations were identified for the exact ATF16LV8C-10JU ordering variant. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status with Microchip before use in a regulated production design.