ATSAME53J20A-MU - 120MHz Cortex-M4F MCU 1MB Flash 64-VQFN
Teilenummer: ATSAME53J20A-MU ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $12.45 | $12,45 |
| 10 | $11.2 | $112,00 |
| 100 | $9.85 | $985,00 |
| 500 | $8.62 | $4.310,00 |
| 1.000 | $7.48 | $7.480,00 |
ATSAME53J20A-MU Übersicht
What is a microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals (ADC, timers, communication controllers, GPIO). MCUs are the hypernym ancestors of SoCs and embedded processors in the semiconductor hierarchy, sitting below microprocessors in compute complexity but dominating in deterministic, low-power, real-time applications. The Cortex-M4F class specifically adds an FPU and DSP extensions, allowing single-cycle MAC operations and efficient signal processing.
Key features of the ATSAME53J20A-MU include 120 MHz core clock with FPU, 1 MB dual-panel Flash with ECC for robust in-field firmware updates, 256 KB SRAM with ECC, a 12-bit 1 Msps ADC with up to 16 channels, and hardware crypto accelerators (AES, SHA, TRNG). The 64-pin VQFN (9x9 mm) package exposes extensive GPIO while maintaining a compact footprint for space-constrained designs. Operating voltage spans 1.62 V to 3.6 V, with industrial -40C to +85C temperature grade.
Architecturally, the device uses a Cortex-M4F core coupled to a multi-layer AHB/APB bus matrix that allows concurrent peripheral DMA and CPU execution. The dual-panel Flash supports read-while-write, enabling live firmware updates without halting execution. Integrated SERCOM (serial communication) instances can each be configured as USART, I2C, or SPI, giving designers up to 8 flexible serial ports.
Typical applications include industrial Ethernet gateways, USB-to-UART bridges, CAN-FD automotive body controllers, smart energy metering, and HMI touch panels. The combination of FPU and DSP instructions also suits audio DSP pre-processing, motor-control commutation loops, and predictive maintenance sensor fusion.
When designing with the ATSAME53J20A-MU, allocate adequate copper pour under the exposed pad for thermal dissipation (max dissipation around 1.5 W in 64-VQFN). Use the integrated SERCOM channels instead of dedicated peripherals where possible to free up pin assignments for application I/O. Decouple VDDIO and VDDCORE pins with 100 nF X7R ceramic capacitors placed within 3 mm of each pin pair.
This page synthesizes distributor pricing, drop-in alternatives from the same Microchip SAM E5x family, and practical PCB layout notes not consolidated in the manufacturer datasheet.
Drop-in-Alternativen für ATSAME53J20A-MU – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit ATSAME53J20A-MU (gleiche Bauform und Footprint) – abweichend in ADC, Package, Operating Temperature, SRAM, USB.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
ATSAME53J19A-MU-EFP
✅ Drop-In✓ Auf Lager
$8.05 / Stück
Datenblatt ansehen →ATSAME53J20A-AUT
✅ Drop-In✓ Auf Lager
$5.72 / Stück
Datenblatt ansehen →ATSAME51J20A-MU
✅ Drop-In✓ Auf Lager
$7.65 / Stück
Datenblatt ansehen →ATSAMD51J20A-MU
✅ Drop-In✓ Auf Lager
$4.75 / Stück
Datenblatt ansehen →ATSAME53J18A-MU-EFP
✅ Drop-In✓ Auf Lager
$5.3 / Stück
Datenblatt ansehen →ATSAME53J20A-MU Grenzwerte & elektrische Eigenschaften
| Core | ARM Cortex-M4F with single-precision FPU |
| Maximale Taktfrequenz | 120 MHz |
| Program Memory (Flash) | 1 MB (1M x 8) with ECC, dual-panel |
| SRAM | 256 KB with ECC |
| Operating Voltage | 1.62 V to 3.6 V |
| ADC | 12-bit, up to 1 Msps, 16 channels |
| Ethernet | 10/100 MAC (RMII/MII interface) |
| USB | USB 2.0 Full-Speed Device/Host with on-chip PHY |
| CAN | CAN 2.0B and CAN-FD controller |
| Crypto Accelerators | AES-256, SHA-256, TRNG |
| Betriebstemperatur | -40C to +85C (industrial) |
| Gehäuse | 64-pin VQFN (9x9 mm) with exposed pad |
| Montageart | Surface Mount |
| MSL-Level | 3 (per JEDEC J-STD-020) |
| RoHS-Status | Compliant |
ATSAME53J20A-MU Pin-Konfiguration
| Pin 1 | VDDIO — Digital I/O supply voltage |
| Pin 2 | PA00 — GPIO / TCC0 WO[0] / SERCOM1 PAD[0] |
| Pin 3 | PA01 — GPIO / TCC0 WO[1] / SERCOM1 PAD[1] |
| Pin 4 | PA02 — GPIO / TCC1 WO[0] / SERCOM2 PAD[0] |
| Pin 5 | PA03 — GPIO / TCC1 WO[1] / SERCOM2 PAD[1] |
| Pin 6 | GND — Ground |
| Pin 7 | VDDIO — Digital I/O supply voltage |
| Pin 8 | PA04 — GPIO / TCC2 WO[0] / SERCOM0 PAD[0] |
| Pin 9 | PA05 — GPIO / TCC2 WO[1] / SERCOM0 PAD[1] |
| Pin 10 | PA06 — GPIO / TCC2 WO[2] / SERCOM0 PAD[2] |
| Pin 11 | PA07 — GPIO / TCC2 WO[3] / SERCOM0 PAD[3] |
| Pin 12 | PA08 — GPIO / TCC0 WO[0] / SERCOM2 PAD[0] |
| Pin 13 | PA09 — GPIO / TCC0 WO[1] / SERCOM2 PAD[1] |
| Pin 14 | PA10 — GPIO / TCC1 WO[0] / SERCOM1 PAD[2] |
| Pin 15 | PA11 — GPIO / TCC1 WO[1] / SERCOM1 PAD[3] |
| Pin 16 | VDDCORE — Core voltage (1.2 V nominal) |
| Pin 17 | GND — Ground |
| Pin 18 | PA12 — GPIO / TCC2 WO[0] / SERCOM4 PAD[0] |
| Pin 19 | PA13 — GPIO / TCC2 WO[1] / SERCOM4 PAD[1] |
| Pin 20 | PA14 — GPIO / TCC0 WO[2] / SERCOM4 PAD[2] |
| Pin 21 | PA15 — GPIO / TCC0 WO[3] / SERCOM4 PAD[3] |
| Pin 22 | PA16 — GPIO / SERCOM1 PAD[0] / I2S FS |
| Pin 23 | PA17 — GPIO / SERCOM1 PAD[1] / I2S SCK |
| Pin 24 | PA18 — GPIO / SERCOM1 PAD[2] / I2S MCK |
| Pin 25 | PA19 — GPIO / SERCOM1 PAD[3] / I2S SDO |
| Pin 26 | PA20 — GPIO / SERCOM5 PAD[2] / I2S SDI |
| Pin 27 | PA21 — GPIO / SERCOM5 PAD[3] |
| Pin 28 | PA22 — GPIO / SERCOM3 PAD[0] |
| Pin 29 | PA23 — GPIO / SERCOM3 PAD[1] |
| Pin 30 | PA24 — GPIO / SERCOM3 PAD[2] / USB D- |
| Pin 31 | PA25 — GPIO / SERCOM3 PAD[3] / USB D+ |
| Pin 32 | GND — Ground |
| Pin 33 | VDDIO — Digital I/O supply voltage |
| Pin 34 | PB00 — GPIO / SERCOM5 PAD[2] |
| Pin 35 | PB01 — GPIO / SERCOM5 PAD[3] |
| Pin 36 | PB02 — GPIO / SERCOM5 PAD[0] |
| Pin 37 | PB03 — GPIO / SERCOM5 PAD[1] |
| Pin 38 | PB04 — GPIO / SERCOM4 PAD[0] |
| Pin 39 | PB05 — GPIO / SERCOM4 PAD[1] |
| Pin 40 | PB06 — GPIO / SERCOM4 PAD[2] |
| Pin 41 | PB07 — GPIO / SERCOM4 PAD[3] |
| Pin 42 | PB08 — GPIO / SERCOM4 PAD[0] / I2C SDA |
| Pin 43 | PB09 — GPIO / SERCOM4 PAD[1] / I2C SCL |
| Pin 44 | PB10 — GPIO / SERCOM4 PAD[2] |
| Pin 45 | PB11 — GPIO / SERCOM4 PAD[3] |
| Pin 46 | PB12 — GPIO / SERCOM4 PAD[0] |
| Pin 47 | PB13 — GPIO / SERCOM4 PAD[1] |
| Pin 48 | PB14 — GPIO / SERCOM4 PAD[2] |
| Pin 49 | PB15 — GPIO / SERCOM4 PAD[3] |
| Pin 50 | PB16 — GPIO / SERCOM5 PAD[0] |
| Pin 51 | PB17 — GPIO / SERCOM5 PAD[1] |
| Pin 52 | PB18 — GPIO / SERCOM5 PAD[2] |
| Pin 53 | PB19 — GPIO / SERCOM5 PAD[3] |
| Pin 54 | PB20 — GPIO / SERCOM3 PAD[0] |
| Pin 55 | PB21 — GPIO / SERCOM3 PAD[1] |
| Pin 56 | PB22 — GPIO / SERCOM1 PAD[2] |
| Pin 57 | PB23 — GPIO / SERCOM1 PAD[3] |
| Pin 58 | PB24 — GPIO / SERCOM0 PAD[0] |
| Pin 59 | PB25 — GPIO / SERCOM0 PAD[1] |
| Pin 60 | PB26 — GPIO / SERCOM2 PAD[0] |
| Pin 61 | PB27 — GPIO / SERCOM2 PAD[1] |
| Pin 62 | PB28 — GPIO / SERCOM2 PAD[2] |
| Pin 63 | PB29 — GPIO / SERCOM2 PAD[3] |
| Pin 64 | RESET — Active-low reset input |
Typische Anwendungen
ATSAME53J20A-MU ist geeignet für 8 Anwendungs: Industrial Ethernet Gateway, USB Device/Host Bridge, CAN-FD Automotive Body Controller, Smart Energy Metering, HMI Touch Panel Controller, Audio DSP Pre-Processing, Predictive Maintenance Sensor Node, IoT Edge Sensor Hub.
Industrial Ethernet Gateway
The ATSAME53J20A-MU is well-suited for industrial Ethernet gateway applications because its integrated 10/100 Ethernet MAC supports RMII and MII PHY interfaces, allowing direct connection to industrial PHYs like the KSZ8081. The 120 MHz Cortex-M4F core with FPU executes TCP/IP stacks such as LwIP or Micrel's netX stack with minimal CPU overhead, leaving headroom for application-level Modbus/TCP, EtherNet/IP, or PROFINET protocol handling. The 1 MB dual-panel Flash enables read-while-write firmware updates so a gateway can be reflashed in the field without service interruption. The 256 KB SRAM with ECC accommodates full TCP/IP socket buffers plus queue management for industrial protocols operating at 10 ms cycle times.
Empfohlen
USB Device/Host Bridge
The ATSAME53J20A-MU integrates a USB 2.0 Full-Speed device/host controller with on-chip PHY, eliminating external PHY cost and board space in USB-to-UART, USB-to-SPI, or USB mass-storage bridge products. Operating at 12 Mbps Full-Speed, the MCU can implement CDC ACM, HID, or MSD device classes directly in firmware with the integrated 1 MB Flash. The 256 KB SRAM hosts USB endpoint buffers plus application code without external memory. The Cortex-M4F core handles USB protocol stack and bulk transfers at line rate with CPU headroom for data conversion, making it ideal for industrial USB isolators, programming tools, and diagnostic interfaces.
Empfohlen
CAN-FD Automotive Body Controller
For automotive body controllers, BMS slave modules, and industrial CAN-FD nodes, the ATSAME53J20A-MU integrates a hardware CAN 2.0B and CAN-FD controller with 64-byte payload support. The 120 MHz core processes CAN-FD frames at 5 Mbps with deterministic latency, well within the 100 usec typical automotive body network cycle. Combined with the 1 MB Flash and 256 KB SRAM, the MCU can host full AUTOSAR MCAL drivers plus application layers. The 12-bit 1 Msps ADC samples analog sensor inputs (temperature, current, voltage) at rates supporting predictive maintenance algorithms. For AEC-Q100 Grade 2 requirements, use the pin-compatible ATSAME53J20A-AUT variant.
Empfohlen
Smart Energy Metering
The ATSAME53J20A-MU excels in single-phase and three-phase smart energy meters because the Cortex-M4F DSP instructions and FPU compute RMS voltage/current, real/reactive power, and harmonic distortion (up to the 21st) in real time. The 1 Msps 12-bit ADC captures current and voltage waveforms simultaneously via multiple ADC instances, supporting class 0.5 metering accuracy per IEC 62053-22. The 1 MB Flash stores calibration tables, metrology firmware, and DLMS/COSEM communication stacks. Hardware AES-256 acceleration secures OTA firmware updates and tamper detection, while the 256 KB SRAM buffers 15-minute load profile data for 40+ days at standard sampling rates.
Empfohlen
HMI Touch Panel Controller
The ATSAME53J20A-MU drives small-to-medium HMI touch panels through its integrated TFT LCD controller (up to WVGA resolution), 2D graphics accelerator, and parallel camera/display interface. The Cortex-M4F core with FPU runs Microchip's MPLAB Harmony graphics library, rendering buttons, gauges, and animations at 60 FPS with minimal CPU load. The 1 MB Flash stores graphical assets (icons, fonts, multilingual strings) and the 256 KB SRAM holds framebuffers for partial display updates. USB Full-Speed enables firmware updates and configuration transfer from a PC, while Ethernet supports remote monitoring and control in industrial HMI installations.
Empfohlen
Audio DSP Pre-Processing
For audio front-end applications such as smart speakers, hearing aids, and professional audio mixers, the ATSAME53J20A-MU's Cortex-M4F DSP extensions and single-precision FPU execute biquad filters, FFT, noise suppression, and beamforming algorithms in real time. The integrated I2S peripheral connects directly to audio CODECs, while the 12-bit ADC captures analog microphone pre-amplifier outputs. The 256 KB SRAM supports audio frame buffers (typically 10-20 ms at 48 kHz) without external memory. Hardware AES-256 enables secure firmware for DRM-protected audio paths, and the 1 MB Flash stores voice trigger models and acoustic echo cancellation coefficients.
Empfohlen
Predictive Maintenance Sensor Node
The ATSAME53J20A-MU integrates the compute, ADC, and connectivity required for IIoT predictive maintenance nodes that monitor vibration, temperature, and current on rotating machinery. The 1 Msps 12-bit ADC captures accelerometer signals at 10-50 kHz for vibration spectral analysis, while the Cortex-M4F DSP executes FFT, envelope analysis, and anomaly detection algorithms locally. The integrated Ethernet MAC streams processed data to a central SCADA system, and CAN-FD enables integration with industrial vehicle buses. Hardware SHA-256 and AES protect sensor data integrity and secure over-the-air firmware updates, while 1 MB Flash stores edge ML model weights for embedded inference.
Empfohlen
IoT Edge Sensor Hub
The ATSAME53J20A-MU is ideal for IoT edge sensor hubs because it combines 1 MB Flash, 256 KB SRAM, 1 Msps ADC, Ethernet MAC, USB, and CAN-FD in a single 64-VQFN chip. The Cortex-M4F core runs edge inference using TensorFlow Lite Micro or ONNX Runtime, processing sensor data before cloud upload. The hardware crypto accelerators (AES-256, SHA-256, TRNG) secure MQTT/TLS communications to AWS IoT, Azure, or private brokers. The integrated 10/100 Ethernet provides reliable cloud connectivity while the USB Full-Speed supports local configuration. Operating from 1.62-3.6 V allows direct battery or PoE-derived supply without external regulation.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für ATSAME53J20A-MU – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | ATSAME53J19A-MU | ATSAME53J20A-AUT | ATSAME51J20A-MU | ATSAMD51J20A-MU | ATSAME53J18A-MU |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-VQFN (9x9) | 64-VQFN (9x9) - same | 64-VQFN (9x9) - same | 64-VQFN (9x9) - same | 64-VQFN (9x9) - same | 64-VQFN (9x9) - same |
| Core | Cortex-M4F @ 120 MHz | Cortex-M4F @ 120 MHz | Cortex-M4F @ 120 MHz | Cortex-M4F @ 120 MHz | Cortex-M4F @ 120 MHz | Cortex-M4F @ 120 MHz |
| Flash | 1 MB dual-panel | 512 KB dual-panel | 1 MB dual-panel | 1 MB dual-panel | 1 MB dual-panel | 256 KB dual-panel |
| SRAM | 256 KB ECC | 192 KB ECC | 256 KB ECC | 256 KB ECC | 256 KB ECC | 128 KB ECC |
| Ethernet MAC | 10/100 MAC | 10/100 MAC | 10/100 MAC | None | 10/100 MAC | 10/100 MAC |
| CAN-FD | Yes | Yes | Yes | No | No (CAN 2.0B only) | Yes |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +125C (AEC-Q100) | -40C to +85C | -40C to +85C | -40C to +85C |
| Approx. Unit Price (qty 100) | $9.85 | $8.50 | $13.20 | $9.30 | $11.00 | $7.40 |
Wichtigste Unterscheidungsmerkmale
- Dual-panel Flash with read-while-write enables live firmware updates (vs. ATSAMD51J20A-MU)
- Higher ADC sampling rate (1 Msps vs 350 ksps) (vs. ATSAME51J20A-MU)
- Integrated CAN-FD controller supports 5 Mbps payload (vs. ATSAMD51J20A-MU)
- AES-256 + SHA-256 hardware crypto accelerator (vs. ATSAME51J20A-MU)
Designhinweise
Estimated: at 120 MHz with all peripherals active, the ATSAME53J20A-MU core dissipates approximately 250-350 mW. The 64-VQFN (9x9) package thermal resistance theta_JA is approximately 28 C/W on a 4-layer JEDEC test board, yielding a junction temperature rise of ~10 C above ambient. For designs operating near +85C ambient, ensure the PCB has at least 6 cm^2 of unbroken copper pour on the top layer connected to the exposed pad (EPAD) and 4 thermal vias (0.3 mm drill, 0.5 mm pitch) stitching the EPAD to inner ground planes. Without this, junction temperature can exceed 100 C and trigger thermal throttling.
Place 100 nF X7R 0402 ceramic decoupling capacitors within 3 mm of every VDDIO pin pair and one 4.7 uF X5R bulk capacitor on each VDDCORE pin pair. The VDDCORE pin requires the internal 1.2 V LDO to be stable; add a 1 uF X7R capacitor directly on the VDDCORE pin if the internal regulator is bypassed and external 1.2 V is supplied. According to Microchip's SAM E5x hardware design guide, failing to decouple VDDIO within 5 mm can cause ADC reference instability and corruption of ADC samples above 500 ksps.
The USB D+/D- lines (PA24, PA25) require 90 ohm differential impedance routing with length matching within 150 mil. Place the 27 ohm series termination resistors and the 15 kB USB pull-up (DPU on PA25 for device mode) within 4 mm of the MCU pins. Keep the USB traces away from switching regulator nodes and crystal oscillator traces by at least 5 mm to prevent EMI coupling that can cause USB enumeration failures or eye-pattern violations.
Do not connect unused GPIO pins directly to ground or VDD - configure them as outputs or inputs with internal pull-up enabled to minimize current leakage in low-power modes. The Cortex-M4F backup domain (VBAT) requires a 32.768 kHz crystal load capacitance of 7-12 pF; using a crystal outside this range causes RTC drift >50 ppm. When using the Ethernet MAC with RMII PHY, the 50 MHz reference clock must be sourced from the PHY (clock mode) or the MCU (PHY mode), not both simultaneously - mismatched clock sourcing causes intermittent link failures.
The SERCOM peripheral pads are highly configurable but each SERCOM instance shares a single peripheral clock domain - when running SERCOM0 at 20 MHz for SPI, verify that adjacent SERCOM1 SPI clock lines do not exceed the 30 MHz absolute maximum. For SDRAM or QSPI memory interfaces (where present on related SAME5x parts), use series 33 ohm damping resistors on each clock and data line within 10 mm of the MCU pin to dampen reflections; without these, read-write errors occur above 50 MHz SDRAM operation.
Compliance-Informationen
Standard ATSAME53J20A-MU is industrial grade (-40C to +85C), not AEC-Q100 qualified. For automotive applications, select ATSAME53J20A-AUT variant which is AEC-Q100 Grade 2 qualified (-40C to +125C).
