ATXMEGA128B3-MN - 32MHz 128KB AVR MCU | Microchip
Teilenummer: ATXMEGA128B3-MN ✓ AktivATXMEGA128B3-MN Übersicht
An AVR XMEGA microcontroller combines an 8-bit microcontroller architecture with a 16-bit instruction set and a wider collection of dedicated peripherals. Within the product hierarchy, it is an 8/16-bit microcontroller, an embedded processing semiconductor, and a member of the power-management-sensitive embedded control category. The XMEGA architecture is intended for designs that require deterministic event handling, direct peripheral routing, and flexible interrupt-driven control without relying on an external interface controller.
Key device resources include 128 KB of in-system programmable flash with read-while-write capability, a dedicated 4 KB boot-code section, 4 KB of SRAM, and 2048 bytes of EEPROM. The two-channel DMA controller and four-channel event system can move data and trigger peripheral actions without continuous central-processing-unit intervention. A programmable multilevel interrupt controller, real-time counter, and 36 GPIO lines support responsive embedded-control and human-interface designs.
The integrated USB full-speed device interface supports direct USB connectivity, while the LCD driver can operate displays with as many as 4 × 25 segments. These interfaces make the MCU suitable for compact control panels, USB-connected instrumentation, programmable logic controllers, and industrial data-acquisition equipment. The manufacturer datasheet also documents in-system programmable flash, boot support, DMA, event-system resources, real-time timing, and multi-level interrupt handling.
Typical uses include USB peripheral control, LCD-based operator interfaces, industrial automation controllers, embedded gateways, and low-power sensor-hub designs. The 32 MHz operating frequency provides useful processing headroom, while the separate boot section permits a dedicated firmware area for startup, recovery, or field-update logic. The EEPROM can retain configuration values without occupying RAM or flash space.
Board design should preserve the exposed-pad thermal and electrical connection specified for the 64-VQFN package and route sensitive inputs away from fast-switching nodes. Decoupling, USB impedance-controlled routing, and careful grounding are especially important in compact USB systems. Confirm pin multiplexing, voltage limits, and peripheral conflicts against the manufacturer datasheet before finalizing the PCB.
This product page combines the device’s principal memory and connectivity specifications with package, sourcing, replacement, and design considerations. It also organizes the most relevant same-footprint option by its actual ordering-code difference, helping engineers distinguish electrical compatibility from packaging, temperature, or delivery variations before committing a design to production.
Drop-in-Alternativen für ATXMEGA128B3-MN – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
ATXMEGA128B3-MNR
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ATXMEGA128B3-MN Grenzwerte & elektrische Eigenschaften
| Product Type | 8/16-bit AVR XMEGA microcontroller |
| Maximale Taktfrequenz | 32 MHz |
| Flash Memory | 128 KB |
| Boot Code Section | 4 KB |
| SRAM | 4 KB |
| EEPROM | 2048 bytes |
| Operating Voltage | 1.6 V to 3.6 V |
| Maximum Operating Temperature | 105 °C |
| General-Purpose I/O | 36 lines |
| DMA Controller | 2 channels |
| Event System | 4 channels |
| USB Interface | USB full-speed device |
| LCD Driver Capacity | Up to 4 × 25 segments |
| Gehäuse | 64-VQFN, 7 mm × 7 mm |
| Montageart | Surface mount |
| Program Memory | Self-programmable, read-while-write flash |
| Real-Time Counter | Integrated |
ATXMEGA128B3-MN 64-vqfn, 7 mm × 7 mm Pinbelegungsleitfaden
Pinbelegung für ATXMEGA128B3-MN (64-vqfn, 7 mm × 7 mm-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für ATXMEGA128B3-MN.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
ATXMEGA128B3-MN ist geeignet für 6 Anwendungs: USB Connected Control Panels, Industrial Automation Controllers, LCD Human-Machine Interfaces, Sensor Hubs and Data Acquisition, Programmable Logic and Relay Controllers, Embedded Gateways and Communication Modules.
USB Connected Control Panels
The ATXMEGA128B3-MN fits USB-connected operator panels because it combines a USB full-speed device interface with 128 KB of flash and a 4 KB SRAM. Its 36 GPIO lines can support buttons, indicators, and panel peripherals, while the LCD controller can drive a display of up to 4 × 25 segments. Use the USB interface for configuration or host communication and route the MCU’s event system to reduce polling overhead. The principal design constraint is careful USB trace layout and grounding in the compact 7 mm × 7 mm VQFN footprint.
Empfohlen
Industrial Automation Controllers
The ATXMEGA128B3-MN is suitable for compact industrial automation modules that require deterministic event handling and mixed digital I/O. Its 32 MHz clock, two-channel DMA controller, four-channel event system, programmable interrupt structure, and 36 GPIO lines allow sensor inputs and actuator outputs to be serviced without excessive polling. The 1.6 V to 3.6 V operating range fits low-voltage embedded systems. For motor, power, or safety-critical control, apply the appropriate isolation, protection, and qualification measures to the complete assembly.
Empfohlen
LCD Human-Machine Interfaces
The ATXMEGA128B3-MN supports compact human-machine interfaces because its LCD driver accommodates displays with as many as 4 × 25 segments. The remaining GPIO lines can operate keys, status LEDs, buzzer outputs, or communication transceivers, while 128 KB of flash provides room for interface firmware. Use the event system to connect button activity directly to display updates and the DMA controller for efficient buffer movement. Validate LCD bias, segment mapping, and timing against the specific panel and MCU pin-multiplexing requirements.
Empfohlen
Sensor Hubs and Data Acquisition
The ATXMEGA128B3-MN can coordinate low-power sensor hubs that periodically acquire measurements and transfer them through USB. Its 2048-byte EEPROM preserves calibration or configuration information, while 4 KB of SRAM supports working buffers and 128 KB of flash accommodates protocol and application code. The two-channel DMA controller reduces processor involvement during transfers, and the four-channel event system helps synchronize sensors, timers, and outputs. Choose external precision references and analog front ends when measurement accuracy exceeds the MCU’s internal conversion resources.
Empfohlen
Programmable Logic and Relay Controllers
The ATXMEGA128B3-MN is well suited to programmable logic and relay-control platforms because 36 GPIO lines provide substantial parallel I/O capacity. Its four-channel event system can coordinate timing-sensitive inputs, while the DMA controller and programmable interrupts support responsive state-machine operation. The 128 KB flash capacity is useful for storing configurable I/O logic and diagnostics, and EEPROM can retain operating parameters. Designers should confirm relay-driver voltage levels, isolation boundaries, flyback paths, and switching-noise margin before assigning outputs.
Empfohlen
Embedded Gateways and Communication Modules
The ATXMEGA128B3-MN fits low-bandwidth embedded gateway designs that need local control plus a USB device connection. Firmware can use the USB interface for configuration, data transfer, or firmware updating, while the event system links external triggers to communication activity. The separate 4 KB boot-code section provides space for startup, recovery, or update logic, and the 2048-byte EEPROM can hold node identity and calibration data. A complete gateway design should add the required transceiver, ESD protection, and power-conversion circuitry.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für ATXMEGA128B3-MN – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | ATXMEGA128B3-MNR |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 64-VQFN, 7 mm × 7 mm | 64-VQFN, 7 mm × 7 mm |
| Maximum Clock Frequency | 32 MHz | 32 MHz |
| Flash Memory | 128 KB | 128 KB |
| Boot Code Section | 4 KB | 4 KB |
| SRAM | 4 KB | 4 KB |
| EEPROM | 2048 bytes | 2048 bytes |
| Operating Voltage | 1.6 V to 3.6 V | 1.6 V to 3.6 V |
| General-Purpose I/O | 36 lines | 36 lines |
| DMA Controller | 2 channels | 2 channels |
| Event System | 4 channels | 4 channels |
| USB Interface | USB full-speed device | USB full-speed device |
| LCD Driver Capacity | Up to 4 × 25 segments | Up to 4 × 25 segments |
| Ordering-Code Difference | Tray-oriented target code | Reel-oriented ordering code |
Wichtigste Unterscheidungsmerkmale
- Combines USB device connectivity with dedicated event-driven peripherals (vs. ATXMEGA128B3-MNR)
- Provides substantial local memory for control firmware (vs. ATXMEGA128B3-MNR)
- Matches the 64-VQFN footprint and 36-line GPIO arrangement (vs. ATXMEGA128B3-MNR)
Designhinweise
Treat the 64-VQFN exposed pad as both a thermal and electrical connection. Follow the manufacturer datasheet land pattern, pin-one orientation, and exposed-pad dimensions exactly, then provide uninterrupted ground-plane copper beneath the device where the recommended pattern permits. Verify the reflow profile and the assembly house’s handling requirements for this fine-pitch, exposed-pad package before releasing the PCB.
Route USB D+ and D− as a controlled-impedance differential pair over a continuous reference plane, with minimal stubs, vias, and test-point discontinuities. Keep the USB transceiver and its protection components close to the corresponding MCU pins. Separate USB routing from switching regulators, relay drivers, and high-current outputs because conducted and radiated coupling can compromise full-speed device operation even when the MCU itself is functioning correctly.
Place the decoupling capacitors required by the manufacturer datasheet directly beside the relevant supply and ground pins, using the shortest possible current paths. Confirm the 1.6 V to 3.6 V operating range at the device pins under transient load rather than only at the regulator output. If the board also supports USB bus-powered operation, evaluate inrush, voltage drop, and capacitor startup behavior as a complete power-path design.
Do not treat ATXMEGA128B3-MN and ATXMEGA128B3-MNR as interchangeable without checking the assembly’s feeding method and order requirements. Their common device identity and 64-VQFN footprint support board compatibility, but a reel-oriented code does not satisfy a production line configured for trays. Likewise, do not infer that every ATxmega128B3 ordering code is pin-compatible without reviewing its package dimensions, temperature range, and exposed-pad layout.
Compliance-Informationen
The available product information identifies a green 1.6 V to 3.6 V device, but specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer documentation or declaration of compliance.