DC-ME-Y413-LX - 9210 16MB/8MB Embedded Module | Digi
Teilenummer: DC-ME-Y413-LX ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $83.71 | $83,71 |
| 10 | $78.5 | $785,00 |
| 100 | $71.2 | $7.120,00 |
| 250 | $67.8 | $16.950,00 |
| 500 | $64.9 | $32.450,00 |
DC-ME-Y413-LX Übersicht
A System-on-Module (SoM) is a pre-certified, production-ready processor and memory subsystem that drops onto a customer's carrier board. SoMs sit hierarchically above discrete MCUs but below full single-board computers, accelerating time-to-market by offloading the hardest parts of high-speed processor design: BGA fan-out, DDR routing, and EMC compliance. The Digi Connect ME family sits at the small-footprint end of the SoM spectrum, optimized for industrial Ethernet and device-server applications.
Key features include the ARM926EJ-S 32-bit RISC core with memory management unit, 10/100 Mbps Ethernet MAC with integrated PHY on selected variants, hardware AES/SHA acceleration, dual high-speed UARTs, SPI, I2C, and GPIO. The module supports Digi's NET+OS or ThreadX development environments, providing POSIX-style APIs and proven TCP/IP stacks. Operating temperature spans -40C to +85C for industrial deployment, and the device carries RoHS compliance with lead-free soldering for global manufacturing.
Typical applications include industrial Ethernet device servers, building automation controllers, point-of-sale terminals, secure remote management appliances, and edge-of-network sensor aggregators. The integrated Ethernet MAC and security engine make the DC-ME-Y413-LX especially attractive for legacy serial-to-Ethernet bridges, replacing dedicated serial-port servers with a programmable, firmware-upgradable platform.
When designing a carrier board, observe the 1.27 mm pitch mezzanine keep-out, provide bulk decoupling on the host 3.3 V rail, and route the differential Ethernet pair as a 100-ohm controlled-impedance pair away from switching nodes. Module firmware image selection (development vs production) is controlled via NET+OS bootstrap pins; leave these accessible for field recovery. The DC-ME-Y413-LX is a mature, broadly deployed part with long-term availability through Digi's embedded product line.
This page synthesizes distributor pricing, parametric alternatives, and design notes that go beyond the manufacturer datasheet by mapping the module's position within the System-on-Module ecosystem and clarifying what differentiates it from sibling parts in the Digi Connect ME/ME 9210 family.
Drop-in-Alternativen für DC-ME-Y413-LX – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
DC-ME-Y413-LX-B
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
DC-ME-Y402-LX
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
DC-ME-01T-S
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
DC-ME-Y413-JT
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
DC-WME-Y413-LX-B
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
DC-ME-Y413-LX Spezifikationen (herstellerveröffentlicht)
| Manufacturer | Digi International |
| Series | Digi Connect ME 9210 |
| Module Type | System-on-Module (SoM) / Embedded Networking Module |
| Processor | Digi NS9210 (ARM926EJ-S core) |
| Core Architecture | ARM926EJ-S, 32-bit RISC |
| CPU Clock Speed | 75 MHz |
| SDRAM | 16 MB |
| Flash Memory | 8 MB |
| Ethernet | 10/100 Mbps MAC (integrated PHY on selected variants) |
| Serial Interfaces | UART, SPI, I2C, GPIO |
| Operating Voltage | 3.3 V |
| Betriebstemperatur | -40C to +85C |
| Form Factor | Digi Connect ME compatible mezzanine |
| Connector Pitch | 1.27 mm board-to-board |
| Montageart | Surface Mount (SMT mezzanine) |
| RoHS-Status | Compliant |
| Lead-Free Status | Lead Free |
| Development Environment | NET+OS / ThreadX |
| Security Engine | Hardware AES/SHA acceleration |
DC-ME-Y413-LX Schnittstellen & Anschlüsse
DC-ME-Y413-LX bietet die folgenden, vom Hersteller veröffentlichten Schnittstellen und Anschlüsse: Ethernet. Pinbelegung der Erweiterungsheader, Nummerierung der Anschlüsse und elektrische Grenzwerte sind in der Herstellerdokumentation definiert.
| Ethernet | 10/100 Mbps MAC (integrated PHY on selected variants) |
Siehe die Herstellerdokumentation für die vollständige Pinbelegung der Erweiterungsleiste und die Nummerierung der Steckverbinder-Pins.
Leistungs- und thermische Eigenschaften
| Betriebstemperatur | -40C to +85C |
Vom Hersteller veröffentlichte Leistungs- und thermische Parameter für DC-ME-Y413-LX.
Typische Anwendungen
DC-ME-Y413-LX ist geeignet für 7 Anwendungs: Industrial Ethernet Device Server, Building Automation Controller, Secure Remote Management Appliance, Point-of-Sale Terminal, Edge-of-Network Sensor Aggregator, Legacy Serial-to-Ethernet Bridge, Medical Device Connectivity Gateway.
Industrial Ethernet Device Server
The DC-ME-Y413-LX is purpose-built for industrial Ethernet device servers that bridge legacy RS-232/RS-485 equipment to TCP/IP networks. The NS9210's integrated 10/100 Ethernet MAC and dual UARTs eliminate the need for an external PHY or serial bridge chip, while the ARM926EJ-S core at 75 MHz runs Digi's NET+OS TCP/IP stack with proven RFC-compliant behavior. Hardware AES/SHA acceleration secures the management plane, and the -40C to +85C operating range supports factory-floor deployment without additional thermal management. Compared with bare MCU designs, the module removes the largest sources of EMI and signal-integrity risk by handling all high-speed processor routing on a pre-characterized PCB. Design tip: place the carrier's magnetics as close as possible to the module's Ethernet pins and route the differential pair as a 100-ohm controlled-impedance net.
Empfohlen
Building Automation Controller
Building automation gateways leverage the DC-ME-Y413-LX to aggregate BACnet, Modbus, and proprietary serial devices into a single Ethernet-attached controller. The module's 16 MB SDRAM comfortably holds the NET+OS image plus BACnet stack, while 8 MB of flash stores configuration, logs, and OTA staging images. The hardware AES engine protects remote-management traffic, and the wide -40C to +85C range handles unconditioned electrical rooms. Compared with Raspberry Pi-class solutions, the DC-ME-Y413-LX offers industrial temperature, long lifecycle, and a deterministic NET+OS or ThreadX environment that vendors can support for decades. Recommend a 32.768 kHz external RTC on the carrier for accurate time-stamping of building events.
Empfohlen
Secure Remote Management Appliance
For out-of-band management of servers, switches, and PDUs, the DC-ME-Y413-LX provides a hardened networking core with hardware-accelerated TLS/SSH. The NS9210 security engine accelerates AES-128/256 and SHA-1/256 hashes, sustaining SSH sessions without CPU saturation at the 75 MHz clock. The 16 MB SDRAM holds OpenSSL-equivalent buffers for VPN tunnels, while the 8 MB flash accommodates dual firmware images for A/B OTA upgrades. Compared with general-purpose SoCs, the DC-ME-Y413-LX draws less power and boots in seconds because there is no Linux userspace to initialize. Pair the module with an external watchdog supervisor on the carrier for unattended deployment.
Empfohlen
Point-of-Sale Terminal
POS terminals benefit from the DC-ME-Y413-LX's compact mezzanine form factor, integrated Ethernet, and secure boot capabilities. The 75 MHz ARM926EJ-S runs the payment-terminal application alongside the NET+OS TCP stack, while the hardware AES engine accelerates PIN-block encryption for PCI-compliant flows. The 16 MB SDRAM/8 MB flash combo is sufficient for thin-client POS designs that delegate catalog and transaction processing to a backend server. Compared with ARM Cortex-A class SoCs, the DC-ME-Y413-LX has a smaller BOM, lower power, and a more deterministic boot path - critical for compliance audits. The 1.27 mm mezzanine also enables low-profile terminal enclosures.
Empfohlen
Edge-of-Network Sensor Aggregator
Edge sensor aggregators consolidate data from RS-485 Modbus, I2C sensor arrays, and SPI peripherals before forwarding over Ethernet. The DC-ME-Y413-LX exposes the UART, SPI, I2C, and GPIO peripherals of the NS9210 directly on the mezzanine, letting a small carrier PCB aggregate dozens of sensor nodes. The 75 MHz ARM926EJ-S runs the protocol conversion firmware without breaking a sweat, and the integrated Ethernet MAC uplinks the aggregated stream with low latency. Hardware AES secures the uplink in industrial IoT contexts. Compare with bare Cortex-M0+ designs, which lack the Ethernet MAC and security offload; the DC-ME-Y413-LX collapses a 3-chip design into one mezzanine.
Empfohlen
Legacy Serial-to-Ethernet Bridge
The DC-ME-Y413-LX is a drop-in modernization path for legacy equipment with serial ports that must now speak Ethernet. The module's dual UARTs and proven NET+OS serial-to-IP libraries (Digi Connectware, Portserver profiles) translate raw RS-232/422/485 traffic to TCP or UDP sockets without rewriting the legacy firmware. The 75 MHz ARM926EJ-S handles a sustained serial bitrate up to 921.6 kbps with headroom for protocol conversion. Compared with discrete ESP32-based bridges, the DC-ME-Y413-LX offers industrial temperature, hardware encryption, and a lifecycle measured in decades rather than years. Recommend adding a serial-port surge protector on the carrier for outdoor deployments.
Empfohlen
Medical Device Connectivity Gateway
Medical device gateways use the DC-ME-Y413-LX to bridge isolated bedside instruments to hospital networks while preserving HIPAA-grade encryption. The NS9210's hardware AES engine handles TLS 1.2 sessions for EHR uploads without exposing patient data, and the -40C to +85C range supports clinical and near-patient environments. The 16 MB SDRAM holds audit-log buffers, while 8 MB of flash stores the validated firmware image and signed configuration. Compared with general-purpose SBCs, the DC-ME-Y413-LX boots deterministically, supports signed firmware updates, and ships with a documented IEC 60601-ready platform story from Digi. Confirm your carrier's creepage and clearance meet IEC 60601-1 for patient-applied equipment.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für DC-ME-Y413-LX – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | DC-ME-Y413-LX-B | DC-ME-Y402-LX | DC-ME-01T-S | DC-ME-Y413-JT | DC-WME-Y413-LX-B |
|---|---|---|---|---|---|---|
| Brand | Digi | Digi | Digi | Digi | Digi | Digi |
| Package / Form Factor | Connect ME 9210 mezzanine (1.27 mm) | Connect ME 9210 mezzanine (1.27 mm) - same | Connect ME 9210 mezzanine (1.27 mm) - same | Connect ME mezzanine (1.27 mm) - same | Connect ME 9210 mezzanine (1.27 mm) - same | Connect ME 9210 wireless mezzanine (1.27 mm) - same |
| Processor | NS9210 (ARM926EJ-S) | NS9210 (ARM926EJ-S) - same | NS9210 (ARM926EJ-S) - same | NS7520 (ARM7TDMI) - older generation | NS9210 (ARM926EJ-S) - same | NS9210 (ARM926EJ-S) + Wi-Fi - same |
| CPU Clock | 75 MHz | 75 MHz | 75 MHz | 55 MHz | 75 MHz | 75 MHz |
| Ethernet | 10/100 MAC | 10/100 MAC | 10/100 MAC | 10/100 MAC | 10/100 MAC | 10/100 MAC + 802.11 wireless |
| Hardware Security | AES/SHA acceleration | AES/SHA acceleration | AES/SHA acceleration | No hardware crypto | AES/SHA acceleration | AES/SHA acceleration + WPA2 |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C (industrial option) | -40C to +85C |
| RoHS / Lead-Free | Yes / Yes | Yes / Yes | Yes / Yes | Yes / Yes | Yes / Yes | Yes / Yes |
Wichtigste Unterscheidungsmerkmale
- Higher CPU clock and integrated security engine vs older NS7520 generation (vs. DC-ME-01T-S)
- Larger on-module memory for full NET+OS applications (vs. DC-ME-Y402-LX)
- Pin-compatible mezzanine with identical carrier layout (vs. DC-ME-Y413-LX-B)
Designhinweise
Estimated: place at least one 10 uF bulk ceramic and a 0.1 uF decoupling cap within 5 mm of the DC-ME-Y413-LX mezzanine power pins to suppress switching transients from the NS9210 core. Route the 100-ohm differential Ethernet pair as a length-matched, impedance-controlled pair away from switching nodes; expect 2-3 mm of pair-to-pair skew tolerance per Digi's Connect ME 9210 hardware reference. Maintain a continuous ground reference plane under the mezzanine connector footprint to control return-path impedance.
Estimated: at 75 MHz with sustained Ethernet and UART traffic, the NS9210 die dissipates approximately 0.5-0.8 W. The Connect ME 9210 mezzanine relies on the host carrier PCB for heat spreading; provide at least 1 square inch of 2 oz copper under the module for convection-cooled deployments. For sealed enclosures without airflow, derate ambient by 10C or add a small clip-on heatsink bonded to the carrier beneath the module.
Do not assume the DC-ME-Y413-LX and DC-ME-01T-S share firmware images - the NS9210 (ARM926EJ-S) and NS7520 (ARM7TDMI) cores are different architectures with different toolchains. Always preserve the NET+OS bootstrap pins on accessible test points for field firmware recovery. Confirm your carrier's 3.3 V rail can source at least 400 mA peak during module bring-up. When migrating from earlier Connect ME variants, re-validate Ethernet PHY strap options because PHY-less vs integrated-PHY variants differ in BOM.
Estimated: the DC-ME-Y413-LX SDRAM interface runs at half the CPU clock; treat the SDRAM bus as a 37.5 MHz source-synchronous group on the host carrier if you are debugging custom carrier layouts. Series-terminate clock and data lines with 22-33 ohm resistors if the carrier extends the bus beyond the standard 1.27 mm mezzanine escape region. Avoid routing GPIO or SPI traces under the Ethernet magnetics to prevent coupling into the PHY.
Compliance-Informationen
RoHS and lead-free per Digi product listing on DigChip; REACH compliance carried forward from Digi corporate policy; AEC-Q100 not applicable for an industrial-grade networking SoM. Halogen-free status not stated in verified distributor data.
