DRV3201-Q1 - Automotive 12V 3-Phase Gate Driver | Texas Instruments
Teilenummer: DRV3201-Q1 ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $6.95 | $6,95 |
| 10 | $6.25 | $62,50 |
| 100 | $5.45 | $545,00 |
| 500 | $4.85 | $2.425,00 |
| 1.000 | $4.35 | $4.350,00 |
DRV3201-Q1 Übersicht
A 3-phase gate driver is a power management IC that provides the level-shifted gate-drive signals required to switch the six power MOSFETs of a three-phase inverter bridge. Positioned between the microcontroller (which generates PWM signals) and the power stage, it translates logic-level inputs into high-current gate pulses, and often integrates current sensing, protection, and diagnostics to support functional-safety systems such as ASIL-rated automotive actuation.
The DRV3201-Q1 provides six dedicated gate drivers for normal-level N-channel MOSFET transistors. The driver capability is designed to handle gate charges up to 250 nC, and the driver source/sink currents are programmable for easy output slope adjustment, enabling EMI optimization. Three high-side and three low-side gate drivers can be switched individually with low propagation delay, supporting PWM-based trapezoidal and field-oriented control schemes.
The device incorporates integrated current shunt amplifiers for phase or bus current measurement, plus enhanced protection features including gate-fault detection, overcurrent, and supply supervisory functions, supporting automotive functional safety architectures. Control and diagnostics are accessed through an SPI interface, giving the MCU visibility into fault conditions and operating status.
Typical applications include automotive 12-V BLDC motor drives such as electric power steering, engine cooling fans, water pumps, fuel pumps, and other safety-relevant actuation systems.
Design tip: take advantage of the programmable gate source/sink currents to tune MOSFET switching slopes - slower turn-on reduces EMI while faster turn-off minimizes switching losses; verify propagation-delay matching across all six channels to minimize dead-time distortion in FOC implementations.
Drop-in-Alternativen für DRV3201-Q1 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
Für dieses Produkt sind keine Drop-in-Alternativen verfügbar.
Alternativen anfordernDRV3201-Q1 Grenzwerte & elektrische Eigenschaften
| Funktion | 3-phase gate driver with current shunt amplifiers |
| Battery Voltage Class | 12 V automotive |
| Gate Drivers | 6 (3 high-side + 3 low-side, N-channel MOSFET) |
| Max Gate Drive Capability | 250 nC gate charge |
| Source/Sink Current | Programmable for output slope adjustment |
| Control Interface | SPI |
| Integrated Amplifiers | Current shunt amplifiers |
| Protection Features | Enhanced protection (overcurrent, fault diagnostics) |
| Target Applications | Automotive 3-phase BLDC, safety-relevant applications |
| Grade | AEC-Q100 automotive qualified (Q1) |
| Gehäuse | HTQFP-64 (PAP), 10x10 mm |
| Montageart | Surface Mount |
| PWM Support | Individual switching of all 6 gate drivers, low propagation delay |
| Ordering Part Number | DRV3201QPAPRQ1 |
DRV3201-Q1 htqfp-64 (pap), 10x10 mm Pinbelegungsleitfaden
Pinbelegung für DRV3201-Q1 (htqfp-64 (pap), 10x10 mm-Gehäuse). Dieses Leistungsbauteil verfügt über Gate-, Drain- und Source-Anschlüsse. Bei nicht gepolten Gehäusen entnehmen Sie die genaue Ausrichtung von Pin 1 und Footprint-Details dem Herstellerdatenblatt. Typische Anwendungen sind Netzteilentwurf, Motoransteuerung und Lastschaltung.
Keine detaillierten Pinbelegungsdaten verfügbar für DRV3201-Q1.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
DRV3201-Q1 ist geeignet für 6 Anwendungs: Electric Power Steering (EPS), Engine Cooling Fan and Water Pump Drives, Fuel Pump and HVAC Blower Motors, Automotive Thermal Management Valves and Actuators, Electric Turbocharger and Start-Stop Support Motors, 48-V Mild-Hybrid Auxiliary BlDC Drives (12-V rail subsystems).
Electric Power Steering (EPS)
The DRV3201-Q1 is designed for safety-relevant automotive 3-phase BLDC drives, making it well suited to electric power steering. Its six gate drivers handle up to 250 nC gate charge, driving the large MOSFETs needed for steering assist torques, while integrated current shunt amplifiers provide phase-current feedback for torque-ripple-free FOC control. Enhanced protection and SPI diagnostics support the fault-detection architecture demanded by steering safety requirements. Programmable source/sink currents let engineers tune switching slopes to meet stringent automotive EMC limits.
Empfohlen
Engine Cooling Fan and Water Pump Drives
Automotive cooling fans and coolant pumps use 12-V 3-phase BLDC motors controlled by PWM, exactly the use case the DRV3201-Q1 targets. The six individual gate drivers with low propagation delay enable efficient trapezoidal or FOC commutation across the wide speed range these loads demand. The integrated current shunt amplifiers reduce BOM count by eliminating external sense amplifiers, and enhanced protection guards the inverter against stall and short-circuit events typical of fan and pump duty cycles.
Empfohlen
Fuel Pump and HVAC Blower Motors
In-tank fuel pumps and HVAC blowers are continuous-duty 12-V BLDC loads where reliability is critical. The DRV3201-Q1's AEC-Q100 qualification, 250 nC gate-charge capability, and programmable slope control allow robust MOSFET switching with minimized radiated EMI in these electrically noisy compartments. SPI-based diagnostics report gate faults and supply anomalies to the host MCU, supporting failure-mode containment for safety-relevant fuel delivery, while integrated shunt amplifiers enable closed-loop speed regulation with minimal external components.
Empfohlen
Automotive Thermal Management Valves and Actuators
Three-phase actuator drives for coolant valves, wastegates, and brake-related actuators are classified as safety-relevant, matching the DRV3201-Q1's stated design intent. Individual switching of all three high-side and three low-side drivers with low propagation delay supports precise position control via FOC. The enhanced protection suite - including gate-fault detection accessible over SPI - enables the diagnostic coverage that ASIL-oriented system architectures require, while integrated shunt amplifiers provide torque/current feedback for accurate force and position loops.
Empfohlen
Electric Turbocharger and Start-Stop Support Motors
High-speed auxiliary automotive motors such as e-turbos demand rapid, low-latency gate switching; the DRV3201-Q1's six individually switched drivers with low propagation delay and programmable 250 nC-class drive strength accommodate fast PWM frequencies needed for smooth high-speed commutation. Current shunt amplifiers feed phase currents to the MCU for field-oriented control at high electrical frequencies, and the enhanced protection features detect overcurrent events quickly, protecting the power stage during transients inherent to turbo speed excursions.
Empfohlen
48-V Mild-Hybrid Auxiliary BlDC Drives (12-V rail subsystems)
In 48-V mild-hybrid vehicles, many auxiliary pumps and fans still run from the 12-V battery rail, where the DRV3201-Q1 operates natively. Its AEC-Q100 qualification and enhanced protection make it suitable for these hybrid-platform subsystems, while SPI diagnostics integrate with the vehicle's fault-management network. The programmable gate source/sink currents let designers balance EMI and efficiency across the diverse load profiles of hybrid auxiliary drives, and integrated shunt amplifiers simplify current-loop implementation relative to discrete solutions.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für DRV3201-Q1 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | DRV3205-Q1 | DRV3211-Q1 | DRV3245-Q1 | DRV3233-Q1 |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Generation | 1st generation 12-V | 1st generation | 1st generation | 2nd generation 12-V | Newest generation 12-V/24-V |
| Battery Voltage Class | 12 V | 12 V | 12 V | 12 V | 12-V/24-V |
| Current Shunt Amplifiers | Integrated | Integrated | Integrated | Integrated | Integrated |
Wichtigste Unterscheidungsmerkmale
- Integrated current shunt amplifiers reduce BOM (vs. DRV3211-Q1)
- High gate-drive capability for large automotive MOSFETs (vs. DRV3233-Q1)
- Safety-focused diagnostics over SPI (vs. DRV3205-Q1)
Designhinweise
Use the DRV3201-Q1's programmable gate source/sink currents to tune MOSFET switching slopes. Slower turn-on reduces dv/dt-driven EMI for CISPR 25 compliance, while keeping turn-off fast to limit switching losses. Iterate slope settings early in the EMC pre-compliance phase rather than adding snubbers later, since slope control affects both radiated and conducted emissions across the full load range.
The DRV3201-Q1 is an older TI device; per TI's E2E support, the DRV3245 and DRV3233 are recommended for new designs. For existing designs, verify that the 250 nC gate-charge rating is not exceeded by your selected MOSFET - exceeding it slows switching and increases heating in the driver. Dead-time and propagation-delay matching across all six channels must be validated in FOC designs to avoid shoot-through and torque distortion.
Route gate-drive loops as short and tight as possible: keep each driver output close to its MOSFET gate with a low-inductance return path to the source. Place shunt-amplifier input routing as a Kelvin connection directly at the shunt resistor pads to preserve accuracy of the integrated current shunt amplifiers, and keep SPI traces away from gate-drive and power-stage switching nodes.
Compliance-Informationen
Q1 designation indicates AEC-Q100 automotive qualification. RoHS/lead-free status per standard TI Q1 offering; REACH and halogen-free status not stated in provided data.
