DSPIC33EDV64MC205-E/M7 - 16-bit DSC with 3-Phase Gate Driver | Microchip
Teilenummer: DSPIC33EDV64MC205-E/M7 ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $0 | $0,00 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1.000 | $0 | $0,00 |
DSPIC33EDV64MC205-E/M7 Übersicht
A Digital Signal Controller is a hybrid of a microcontroller (MCU) and a digital signal processor (DSP): it provides the peripherals, interrupts, and ease of use of an MCU while adding DSP-grade multiply-accumulate execution for control-loop mathematics. In the power-management hierarchy, the dsPIC33EDV64MC205 goes one step further - it is a motor-control SiP that merges the controller, analog front end, and power stage driver into one package, sitting above standalone MCUs and below full gate-driver-plus-MCU two-chip solutions.
Key features include high-speed PWM peripherals purpose-built for 3-phase motor control, integrated operational amplifiers and advanced analog for current-sense conditioning, and the co-packaged 12V 3-phase MOSFET gate driver with an on-chip LDO - eliminating external driver circuitry. The 64KB Flash (22K x 24 instruction words) and 8KB RAM support field-oriented control (FOC) with sensorless or sensored feedback.
Architecturally, the dsPIC33E core provides sixteen 16-bit Working registers, each usable as data, address, or offset register, with DSP multiply-accumulate instructions executing in single cycles at up to 70 MIPS, enabling tight FOC loop rates for PMSM and BLDC machines.
Typical applications include low-voltage PMSM/BLDC motor drives, power tools, drones and e-mobility drives, and compact industrial servo modules where board area is constrained.
Design consideration: because the gate driver shares the package with the DSC, pay close attention to power-ground separation and gate-loop layout on the PCB to keep switching noise out of the analog front end.
This page synthesizes distributor availability data, drop-in family alternatives, and application guidance not found in a single manufacturer datasheet. Pricing is available on request as of 2026-09-23.
Drop-in-Alternativen für DSPIC33EDV64MC205-E/M7 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit DSPIC33EDV64MC205-E/M7 (gleiche Bauform und Footprint) – abweichend in Integrated Op Amps, Package, Program Memory Size, RAM Size.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
DSPIC33EDV64MC205-I/M7
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
DSPIC33EDV64MC205-H/M7
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
DSPIC33EDV64MC205T-E/M7
✅ Drop-In✓ Auf Lager
Preis auf Anfrage
Datenblatt ansehen →DSPIC33EDV64MC205T-H/M7
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
DSPIC33EDV64MC205-E/M7 Grenzwerte & elektrische Eigenschaften
| Core Architecture | 16-bit dsPIC DSC (DSP-capable) |
| Program Memory Size | 64 KB (22K x 24) Flash |
| RAM Size | 8 KB |
| Maximale Taktfrequenz | 60 MHz |
| Core Performance | Up to 70 MIPS |
| Integrated Gate Driver | 3-phase MOSFET gate driver, 12 V |
| Integrated LDO | Yes |
| Integrated Op Amps | Yes (advanced analog) |
| PWM | High-speed PWM (motor control) |
| Product Type | System in Package (SiP) |
| Gehäuse | 48-VQFN (6x6), 52-pin capable (EP) |
| Montageart | Surface Mount |
| Operating Temperature Grade | -40C to +125C (E grade) |
| Technology | CMOS, Flash program memory |
| Target Applications | Low-voltage PMSM/BLDC motor control |
DSPIC33EDV64MC205-E/M7 48-vqfn (6x6), 52-pin capable (ep) Pinbelegungsleitfaden
Pinbelegung für DSPIC33EDV64MC205-E/M7 (48-vqfn (6x6), 52-pin capable (ep)-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für DSPIC33EDV64MC205-E/M7.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
DSPIC33EDV64MC205-E/M7 ist geeignet für 6 Anwendungs: Low-Voltage PMSM Motor Drives, BLDC Drives for Power Tools, Drone and e-Mobility ESCs, Industrial Servo and Automation Modules, Battery-Powered Appliance Motor Control, Pumps, Fans and HVAC Blowers.
Low-Voltage PMSM Motor Drives
The DSPIC33EDV64MC205-E/M7 is purpose-built for low-voltage permanent magnet synchronous motor (PMSM) control. According to Microchip's Development Board User's Guide, the co-packaged 12V 3-phase MOSFET gate driver and dsPIC DSC form a single-chip solution for PMSM drives. The 70 MIPS core executes field-oriented control at high loop rates, while the high-speed PWM peripheral generates complementary 3-phase drive signals with dead-time control. Integrated op amps condition low-side shunt current feedback, and the on-chip LDO derives the gate-driver supply. The -E grade (-40C to +125C) covers motor-drive self-heating, and the 6x6 mm VQFN fits compact power stages.
Empfohlen
BLDC Drives for Power Tools
Cordless power tools demand compact, high-efficiency brushless DC (BLDC) controllers that survive mechanical shock and elevated temperatures. The DSPIC33EDV64MC205-E/M7 fits this role because one 48-VQFN (6x6) package replaces the MCU, gate driver, and regulator, shrinking the control PCB inside crowded tool housings. The 64KB Flash holds sensorless FOC or trapezoidal control firmware, 8KB RAM supports state observers, and the 12V-rated 3-phase gate driver directly switches the external MOSFET bridge. The -E temperature grade tolerates the hot environment near the motor, and integrated analog reduces component count for cost-sensitive tool BOMs.
Empfohlen
Drone and e-Mobility ESCs
Electronic speed controllers (ESCs) for drones, e-scooters, and light e-mobility platforms benefit from the SiP's integration density. At 6x6 mm, the DSPIC33EDV64MC205-E/M7 minimizes control-board area and mass, while the 70 MIPS DSP core runs sensorless field-oriented control algorithms with fast current loops essential for smooth torque at high electrical frequencies. The integrated 12V 3-phase gate driver supports low-voltage battery stacks directly, and the high-speed PWM offers the resolution needed for quiet, efficient propulsion. The -E grade handles ESC thermal stress during sustained high-current flight or acceleration profiles.
Empfohlen
Industrial Servo and Automation Modules
Compact servo drives and factory automation axes require deterministic control loops and robust communication. The dsPIC33E core of the DSPIC33EDV64MC205-E/M7 provides sixteen 16-bit Working registers and single-cycle DSP instructions, enabling precise position, velocity, and current cascades at kilohertz rates. The integrated gate driver and LDO reduce the drive-stage footprint on dense automation PCBs, and the extended -40C to +125C operating range suits sealed industrial cabinets. High-speed PWM with fault inputs supports safe shutdown, and the Flash memory accommodates field-updatable control firmware for multi-axis machinery platforms.
Empfohlen
Battery-Powered Appliance Motor Control
Battery-powered appliances - vacuums, mixers, garden equipment - gain efficiency and runtime from brushless motors governed by the DSPIC33EDV64MC205-E/M7. The single-chip integration of controller, 12V 3-phase gate driver, and LDO cuts board cost and assembly steps in high-volume appliance manufacturing. The 64KB Flash supports efficiency-optimizing sensorless algorithms, while integrated op amps enable low-cost single-shunt current sensing. The 60 MHz / 70 MIPS performance keeps control overhead low even at high motor electrical speeds, and the VQFN's exposed pad aids thermal dissipation within sealed plastic housings.
Empfohlen
Pumps, Fans and HVAC Blowers
Continuous-duty fans, pumps, and HVAC blowers benefit from the DSPIC33EDV64MC205-E/M7's reliability-focused integration. Sensorless FOC executed on the 70 MIPS core reduces acoustic noise and improves efficiency versus trapezoidal control, extending bearing and battery life. The co-packaged 12V gate driver directly drives the 3-phase bridge, trimming the BOM of high-volume blowers, and the -E temperature grade covers rooftop and plenum environments. Flash self-programming allows firmware updates in the field, and integrated analog simplifies over-current protection sensing for unattended, always-on equipment.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für DSPIC33EDV64MC205-E/M7 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | DSPIC33EDV64MC205-I/M7 | DSPIC33EDV64MC205-H/M7 | DSPIC33EDV64MC205T-E/M7 | DSPIC33EDV64MC205T-H/M7 |
|---|---|---|---|---|---|
| Package | 48-VQFN (6x6) /M7 | 48-VQFN (6x6) - same | 48-VQFN (6x6) - same | 48-VQFN (6x6) - same | 48-VQFN (6x6) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| RAM | 8 KB | 8 KB | 8 KB (8192 words) | 8 KB | 8 KB |
| Core Performance | Up to 70 MIPS (60 MHz clock) | Up to 70 MIPS (60 MHz) | 60 MHz max clock | Up to 70 MIPS (60 MHz) | 60 MHz max clock |
| Integrated 3-Phase Gate Driver | Yes, 12 V | Yes, 12 V | Yes, 12 V | Yes, 12 V | Yes, 12 V |
| Temperature Range | -40C to +125C (E grade) | -40C to +85C (I grade) | -H grade | -40C to +125C (E grade) | -H grade |
| Packaging / Delivery | Tray / cut tape | Tray / cut tape | Tray / cut tape | Tape & Reel | Tape & Reel |
Wichtigste Unterscheidungsmerkmale
- Single-chip integration of gate driver and controller (vs. DSPIC33CK64MC105)
- Extended temperature range for hot motor-drive environments (vs. DSPIC33EDV64MC205-I/M7)
- DSP-grade control throughput (vs. DSPIC33EDV64MC205-H/M7)
Designhinweise
Because this SiP combines a DSC and a 12V 3-phase MOSFET gate driver, power and signal domains share one 48-VQFN (6x6) footprint. Route gate-drive loops as short and wide as possible, place bootstrap capacitors at the driver pins, and use the exposed pad as a low-inductance ground return. Partition the power ground from the analog ground feeding the integrated op amps, joining them at a single star point. Use Microchip's Motor Control Development Board (DS50002883A) layout as a verified starting reference.
Switching edges from the co-packaged gate driver couple into current-sense traces used by the FOC control loops. Keep shunt-resistor kelvin connections directly to the integrated op amp inputs, apply short RC filtering at the sense nodes sized to the control-loop bandwidth, and avoid routing PWM or gate signals parallel to analog traces on adjacent layers. Sampling current away from switching instants (PWM-triggered ADC sampling) further reduces noise in the 70 MIPS core's control calculations.
Estimated: gate-driver and DSC dissipation concentrate in the exposed pad of the VQFN. With the -E grade rated to +125C ambient, budget junction margin by ensuring a solid via array (e.g., 4x4 grid of 0.3 mm vias) from the exposed pad to internal ground planes and, where possible, to a bottom-side copper pour. Motor-drive PCBs that omit this via array can experience significantly higher silicon temperatures under sustained load - verify with thermography on the populated board against Microchip's reference board measurements.
Do not confuse clock and MIPS figures when budgeting control-loop timing: distributor listings quote 60 MHz maximum clock while the datasheet states up to 70 MIPS core performance - the pipelined core completes more than one instruction per clock in DSP operations. Also verify the temperature suffix on purchase orders: -E, -I, and -H variants are pin-identical, so an incorrect grade substitution may pass electrical test yet fail in hot enclosures. Order the T (tape-and-reel) suffix for production reels.
Compliance-Informationen
Compliance data not stated in the provided web sources; verify against Microchip's official product page or datasheet DS70005292F before qualification.
