DSPIC33EP32MC502T-E/MM - 60MIPS Motor Control DSC, 28-QFN | Microchip
Teilenummer: DSPIC33EP32MC502T-E/MM ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $4.62 | $4,62 |
| 10 | $4.2 | $42,00 |
| 100 | $3.75 | $375,00 |
| 500 | $3.4 | $1.700,00 |
| 1.000 | $3.05 | $3.050,00 |
DSPIC33EP32MC502T-E/MM Übersicht
A digital signal controller merges the computational throughput of a DSP with the deterministic control architecture of a microcontroller. Within the power management hierarchy of embedded systems, the DSC sits between general-purpose MCUs and dedicated DSPs, providing single-cycle MAC, DSP engine instructions, and high-resolution PWM peripherals that general-purpose MCUs lack, while retaining flexible, interrupt-driven control flow.
Key features include the enhanced 16-bit dsPIC DSC core clocked at up to 60 MIPS, motor-control-oriented peripherals, and connectivity covering CAN, I2C, SPI, UART/USART, IrDA, LINbus, and QEI (quadrature encoder interface). This communications suite makes the part well suited to networked motor systems sharing a CAN or LIN bus. The 60 MHz (60 MIPS) core speed enables field-oriented control (FOC) loops for brushless DC and permanent magnet synchronous machines.
Architecturally, the dsPIC33EP core integrates a DSP engine with single-cycle MAC and hardware division support, plus dedicated motor-control PWM peripherals with complementary outputs and dead-time insertion. On-chip FLASH of 32 KB holds both code and self-programming firmware, and the 4 KB RAM supports control-state data structures. According to the Microchip product page, dsPIC33E controllers enable high-performance precision motor control systems that are more energy efficient and quieter in operation.
Typical applications include brushless DC and permanent magnet motor drives, industrial automation, power conversion (PFC, inverter control), automotive auxiliary drives, and consumer appliances with sensor or sensorless FOC.
A key design consideration is power supply sequencing and VDDCORE decoupling: use the recommended VCAP capacitor on the internal regulator output and place it as close to the VCAP pin as possible for stable core operation.
This page synthesizes distributor data, drop-in same-package alternatives, FAQs, and design guidance not found in the manufacturer datasheet.
Drop-in-Alternativen für DSPIC33EP32MC502T-E/MM – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit DSPIC33EP32MC502T-E/MM (gleiche Bauform und Footprint) – abweichend in Operating Temperature, Package, Core Architecture, Qualification, Series.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
DSPIC33EP32MC502T-I/MM
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
DSPIC33EP32GP502T-E/MM
✅ Drop-In✓ Auf Lager
$2.98 / Stück
Datenblatt ansehen →DSPIC33EP32MC502-E/MM
✅ Drop-In✓ Auf Lager
$2.98 / Stück
Datenblatt ansehen →DSPIC33EP64MC502-E/MM
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$3.05 / Stück
Datenblatt ansehen →DSPIC33EP32MC203T-I/TL
✅ Drop-In✓ Auf Lager
$1.65 / Stück
Datenblatt ansehen →DSPIC33EP32MC502T-E/MM Grenzwerte & elektrische Eigenschaften
| Core | 16-bit dsPIC DSC |
| Core Speed | 60 MIPs |
| Program Memory | 32 KB (10.7K x 24) FLASH |
| Data RAM | 4 KB (2K x 16) |
| Series | dsPIC33EP MC (Motor Control) |
| Gehäuse | 28-QFN-S (6x6 mm) |
| Betriebstemperatur | -40C to +125C (E grade, extended) |
| CAN | Yes (CANbus) |
| I2C | Yes |
| SPI | Yes |
| UART/USART | Yes (with IrDA, LINbus support) |
| QEI (Quadrature Encoder Interface) | Yes |
| Montageart | Surface Mount |
| Packaging Suffix | T = Tape and Reel |
| AEC-Q100 | Automotive/AEC-Q100 family listing per distributor data |
DSPIC33EP32MC502T-E/MM Pin-Konfiguration
| Pin 1 | MCLR — Master clear reset input (active low) |
| Pin 2 | AN0/RB0 — Analog input 0 / PORTB bit 0 |
| Pin 3 | AN1/RB1 — Analog input 1 / PORTB bit 1 |
| Pin 4 | AN2/RP1/RB2 — Analog input 2 / remappable peripheral pin RP1 / PORTB bit 2 |
| Pin 5 | AN3/RP2/RB3 — Analog input 3 / remappable peripheral pin RP2 / PORTB bit 3 |
| Pin 6 | AN4/RP3/RB4 — Analog input 4 / remappable peripheral pin RP3 / PORTB bit 4 |
| Pin 7 | AN5/RP4/RB5 — Analog input 5 / remappable peripheral pin RP4 / PORTB bit 5 |
| Pin 8 | VDD — Power supply (positive) |
| Pin 9 | VSS — Ground reference |
| Pin 10 | OSC1/CLKI — Crystal oscillator input / external clock input |
| Pin 11 | OSC2/CLKO/RC15 — Crystal oscillator output / clock output / PORTC bit 15 |
| Pin 12 | SOSCI/RP5/RC13 — Secondary oscillator input / remappable pin RP5 / PORTC bit 13 |
| Pin 13 | SOSCO/T1CK/RC14 — Secondary oscillator output / Timer1 clock / PORTC bit 14 |
| Pin 14 | VDD — Power supply (positive) |
| Pin 15 | VSS — Ground reference |
| Pin 16 | RP6/RB6 — Remappable peripheral pin RP6 / PORTB bit 6 |
| Pin 17 | RP7/RB7 — Remappable peripheral pin RP7 / PORTB bit 7 |
| Pin 18 | RP8/RB8 — Remappable peripheral pin RP8 / PORTB bit 8 |
| Pin 19 | RP9/RB9 — Remappable peripheral pin RP9 / PORTB bit 9 |
| Pin 20 | VDD — Power supply (positive) |
| Pin 21 | RP10/RB10 — Remappable peripheral pin RP10 / PORTB bit 10 |
| Pin 22 | RP11/RB11 — Remappable peripheral pin RP11 / PORTB bit 11 |
| Pin 23 | RP12/RB12 — Remappable peripheral pin RP12 / PORTB bit 12 |
| Pin 24 | RP13/RB13 — Remappable peripheral pin RP13 / PORTB bit 13 |
| Pin 25 | RP14/RB14 — Remappable peripheral pin RP14 / PORTB bit 14 |
| Pin 26 | RP15/RB15 — Remappable peripheral pin RP15 / PORTB bit 15 |
| Pin 27 | VCAP/VDDCORE — Internal core regulator output - connect external stabilizing capacitor to VSS |
| Pin 28 | VSS — Ground reference |
Typische Anwendungen
DSPIC33EP32MC502T-E/MM ist geeignet für 6 Anwendungs: Brushless DC (BLDC) Motor Drives, Permanent Magnet Synchronous Motor (PMSM) Servo Systems, Automotive Auxiliary Motor Control, Digital Power Conversion (PFC, DC-DC, Inverters), Industrial Automation and Networked Actuators, Appliances and Consumer Motor Products.
Brushless DC (BLDC) Motor Drives
The DSPIC33EP32MC502T-E/MM is purpose-built for BLDC motor control: its 60 MIPS core executes field-oriented control or trapezoidal commutation loops at 10-20 kHz PWM frequencies with substantial computational margin. Dedicated motor-control PWM outputs with dead-time insertion directly drive three-phase inverter gate drivers, while the QEI peripheral accepts incremental encoder feedback for closed-loop speed and position control. In a typical 24 V or 48 V BLDC fan, pump, or treadmill drive, the DSC sits between a current-sense stage and the MOSFET gate drivers, computing PI/FOC loops in firmware. The 32 KB FLASH holds the entire control stack including CAN communication, and the -40C to +125C grade permits mounting inside thermally stressed motor housings where industrial-grade parts would exceed their ratings.
Empfohlen
Permanent Magnet Synchronous Motor (PMSM) Servo Systems
For PMSM servo and robotics joints, the DSPIC33EP32MC502T-E/MM provides the 60 MIPS DSP engine with single-cycle MAC needed for high-bandwidth field-oriented control, plus the QEI interface for resolver-substitute incremental encoders. The CAN and UART interfaces allow the drive to report status and receive motion commands from a host controller over industrial fieldbus. With 4 KB of RAM, position, velocity, and current-loop state variables coexist with communication buffers in on-chip memory, eliminating external RAM. The extended -40C to +125C operating range suits servo axes mounted near gearboxes and motors where ambient temperatures rise above 85C. Firmware complexity, including S-curve profiling and feed-forward, fits within the 32 KB FLASH program space typical of single-axis servo firmware.
Empfohlen
Automotive Auxiliary Motor Control
Automotive 12 V auxiliary loads - HVAC blowers, radiator fans, fuel pumps, window lifts - benefit from the DSPIC33EP32MC502T-E/MM extended temperature grade and CAN connectivity. Distributor data categorizes this part under automotive/AEC-Q100 family listings, and the -40C to +125C range covers underhood and in-cabin thermal extremes. The CAN interface connects the motor node to body-control or vehicle-domain controllers, while LIN support covers lower-cost lighting and actuator sub-buses. The 28-QFN-S (6x6) package keeps the controller footprint small on space-constrained actuator PCBs. Designers should verify PPAP and specific qualification certificates with Microchip for production automotive programs, as certificate scope varies by ordering suffix.
Empfohlen
Digital Power Conversion (PFC, DC-DC, Inverters)
Switched-mode power stages - power factor correction, LLC converters, and solar micro-inverters - use the DSPIC33EP32MC502T-E/MM for high-frequency digital control. The 60 MIPS core closes current-mode control loops at switching frequencies of 100-300 kHz, and the motor-control PWM module generates complementary outputs with programmable dead time for half-bridge and full-bridge stages. The ADC subsystem samples inductor current and bus voltage synchronized to PWM, and SPI/I2C connect to digital supervisors. The extended temperature grade allows mounting inside sealed power supplies where internal ambient exceeds 85C, and 32 KB FLASH is adequate for one control loop plus housekeeping and CAN/UART monitoring firmware typical of digital power products.
Empfohlen
Industrial Automation and Networked Actuators
Factory automation nodes - conveyor positioners, valve actuators, dosing pumps - integrate the DSPIC33EP32MC502T-E/MM where a single chip must combine motor drive, sensing, and fieldbus communication. CAN and LIN interfaces connect to industrial networks, UART/SPI link to HMI and sensors, and QEI reads shaft encoders for positioning feedback. The 60 MIPS core runs control and protocol stacks concurrently, and the -40C to +125C grade survives enclosure interiors adjacent to drives and switching power supplies. In a networked actuator, one DSC replaces separate MCU plus communication-controller chips, reducing BOM count. The remappable RP pin architecture lets designers route UART, SPI, and PWM to any of several physical pins, simplifying PCB routing on dense actuator boards.
Empfohlen
Appliances and Consumer Motor Products
High-efficiency home appliances - washing machine drives, refrigerator compressors, range hoods - use the DSPIC33EP32MC502T-E/MM for sensorless or sensored FOC of PMSM motors, delivering the quieter, more energy-efficient operation Microchip cites for the dsPIC33E family. The LIN/UART interface supports appliance communication buses, and I2C connects to user-interface controllers and temperature sensors. The extended temperature grade tolerates the hot interior of appliance chassis near compressor and motor windings. Single-chip integration of motor control plus communication reduces total appliance electronics cost. Firmware for sensorless back-EMF observers and speed ramps fits comfortably in the 32 KB FLASH, and the 28-QFN-S package supports compact single-sided main control boards.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für DSPIC33EP32MC502T-E/MM – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | DSPIC33EP32MC502T-I/MM | DSPIC33EP32GP502T-E/MM | DSPIC33EP64MC502-E/MM | DSPIC33EP32MC203T-I/TL |
|---|---|---|---|---|---|
| Package | 28-QFN-S (6x6) | 28-QFN-S (6x6) - same | 28-QFN-S (6x6) - same | 28-QFN-S (6x6) - same | 28-pin QFN (TL) - same family footprint |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core Speed | 60 MIPs | 60 MIPs | 60 MIPs | 60 MIPs | 60 MIPs |
| FLASH Program Memory | 32 KB (10.7K x 24) | 32 KB | 32 KB | 64 KB | 32 KB |
| Operating Temperature | -40C to +125C (E) | -40C to +85C (I) | -40C to +125C (E) | -40C to +125C (E) | -40C to +85C (I) |
| Peripheral Family (PWM/QEI/CAN emphasis) | MC - motor control (PWM, QEI, CAN) | MC - motor control | GP - general purpose | MC - motor control | MC - motor control |
Wichtigste Unterscheidungsmerkmale
- Extended -40C to +125C temperature grade in QFN-28 (vs. DSPIC33EP32MC502T-I/MM)
- Motor-control peripheral set with QEI and CAN on one chip (vs. DSPIC33EP32GP502T-E/MM)
- 32 KB FLASH minimizes cost for compact FOC firmware (vs. DSPIC33EP64MC502-E/MM)
Designhinweise
The dsPIC33EP core is supplied by an internal regulator whose output appears on the VCAP pin (pin 27). Always connect the manufacturer-recommended low-ESR capacitor from VCAP to VSS, placed within 1-2 mm of the pin; omitting or undersizing this capacitor causes core-supply instability, brown-out resets, or erratic execution at 60 MIPS. Decouple each VDD pair (pins 8/14/20) with 100 nF ceramic plus bulk capacitance per Microchip layout guidance in the family datasheet.
Use a solid ground plane under the 28-QFN-S (6x6) and connect the exposed die pad to the ground plane with a via array to reduce ground bounce between the motor-control PWM stage and the ADC. Keep the gate-driver return paths separate from analog signal returns to preserve ADC accuracy for current sensing in FOC loops. Place the crystal for OSC1/OSC2 close to pins 10 and 11 with short traces and ground guard.
The /MM QFN package exposes PGD/PGC programming pins that double as remappable RP I/O - do not permanently load them with external circuits that clamp ICSP voltage levels, or in-circuit programming will fail. Remappable peripheral pins (RPx) must be locked after configuration when using write-protection. Also verify E-grade (-40C to +125C) is truly required before paying the price premium; the I-grade (DSPIC33EP32MC502T-I/MM) is drop-in identical up to +85C.
Compliance-Informationen
Distributor data (globalspec) lists the part under automotive/AEC-Q100 family categorization; lead-free for modern Microchip SMD production. RoHS/REACH certificates should be confirmed on the Microchip product page before procurement.
