DSPIC33EV128GM006-I/PT - 16-bit 70 MIPS 5V DSC, 128KB Flash | Microchip
Teilenummer: DSPIC33EV128GM006-I/PT ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $6.85 | $6,85 |
| 10 | $6.18 | $61,80 |
| 100 | $5.5 | $550,00 |
| 500 | $4.95 | $2.475,00 |
| 1.000 | $4.4 | $4.400,00 |
DSPIC33EV128GM006-I/PT Übersicht
A digital signal controller combines the computational architecture of a digital signal processor - including a hardware multiplier, DSP instructions, and a 24-bit program word - with the peripheral set and control logic of a microcontroller. Within the embedded processing hierarchy, a DSC such as the dsPIC33EV family sits between general-purpose microcontrollers and dedicated DSPs, making it well suited to real-time control loops that demand both mathematical throughput and robust, deterministic I/O behavior.
Differentiating specifications of this device include the 5V-tolerant operating range that simplifies designs in harsh 12V and 24V industrial and automotive environments without external transceivers, 6 motor-control PWM channels rated for inverter and BLDC drive stages, 3 integrated operational amplifiers that reduce external analog component count and BOM cost, a CTMU (Charge Time Measurement Unit) for capacitive touch and time-based measurement, and a SENT peripheral supporting the SAE J2716 sensor interface used in automotive networks. ECC (error-correcting code) on Flash protects program memory integrity, a key requirement for functional-safety-oriented designs.
Architecturally, the dsPIC33EV core executes an enhanced 16-bit instruction set with DSP multiply-accumulate operations, 4 DMA channels, and 7 timers that offload the CPU from data movement and timing tasks. Peripheral Pin Select (PPS) allows flexible remapping of digital peripherals to a wide range of I/O pins, although a few functions retain fixed pin assignments per the family data sheet.
Typical applications include automotive sensor and touch-control units, BLDC and PMSM motor drives, appliance control boards, power supplies and inverters, and industrial systems exposed to electrical noise and vibration. The 5V-native I/O directly interfaces with legacy industrial logic levels without external level shifters.
For design, note that the I-suffix temperature grade covers -40C to +85C; choose the E-suffix (-40C to +125C) for under-hood automotive environments, or the H-suffix for 40 MHz operation. Plan a robust decoupling network on each VDD/VSS pair.
This page synthesizes verified distributor pricing, same-footprint drop-in alternatives, and practical design guidance not found in the manufacturer datasheet alone.
Drop-in-Alternativen für DSPIC33EV128GM006-I/PT – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit DSPIC33EV128GM006-I/PT (gleiche Bauform und Footprint) – abweichend in Package, Core Architecture, Operating Temperature, ADC, Maximum CPU Speed.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
DSPIC33EV128GM006-E/PT
✅ Drop-In✓ Auf Lager
$3.4 / Stück
Datenblatt ansehen →DSPIC33EP64GS805-I/PT
✅ Drop-In✓ Auf Lager
$3.48 / Stück
Datenblatt ansehen →DSPIC33EP512GM604-I/PT
✅ Drop-In✓ Auf Lager
$7.4 / Stück
Datenblatt ansehen →dsPIC33EP512GM306-I/PT
✅ Drop-In✓ Auf Lager
$7.18 / Stück
Datenblatt ansehen →DSPIC33EP256MC506-E/PT
✅ Drop-In✓ Auf Lager
$5.83 / Stück
Datenblatt ansehen →DSPIC33EP512MC806-E/PT
✅ Drop-In✓ Auf Lager
$8.75 / Stück
Datenblatt ansehen →DSPIC33EV128GM006-I/PT Grenzwerte & elektrische Eigenschaften
| Core Architecture | dsPIC33EV 16-bit DSC |
| Maximum CPU Speed | 70 MIPS (60 MHz core clock) |
| Program Flash Memory | 128 KB (43K x 24) with ECC |
| RAM | 8 KB |
| Versorgungsspannung | 4.5 V to 5.5 V (5V nominal) |
| Betriebstemperatur | -40 C to +85 C (I grade) |
| Motor Control PWM Channels | 6 |
| Integrated Operational Amplifiers | 3 |
| CTMU (Charge Time Measurement Unit) | Yes |
| SENT Peripheral (SAE J2716) | Yes |
| DMA Channels | 4 |
| Timers | 7 (16/32-bit) |
| Gehäuse | 64-pin TQFP (10x10x1 mm) |
| Montageart | Surface Mount |
| RoHS-Status | Compliant |
| Functional Safety Support | FuSa documentation package |
DSPIC33EV128GM006-I/PT Pin-Konfiguration
| Pin 1 | RP15/RP1 — Remappable I/O (Peripheral Pin Select) |
| Pin 2 | RP14/PWM1L — Remappable I/O / PWM1 Low output |
| Pin 3 | RP13/PWM1H — Remappable I/O / PWM1 High output |
| Pin 4 | RP12/PWM3L — Remappable I/O / PWM3 Low output |
| Pin 5 | RP11/PWM3H — Remappable I/O / PWM3 High output |
| Pin 6 | RP10/PWM5L — Remappable I/O / PWM5 Low output |
| Pin 7 | RP9/PWM5H — Remappable I/O / PWM5 High output |
| Pin 8 | VDD — Supply voltage (5V) |
| Pin 9 | VSS — Ground |
| Pin 10 | OSC1/CLKI — Crystal oscillator input or external clock |
| Pin 11 | OSC2/CLKO — Crystal oscillator output |
| Pin 12 | MCLR — Master Clear (reset, active low) |
| Pin 13 | PGEDx2 — Programming/debug data |
| Pin 14 | PGECx2 — Programming/debug clock |
| Pin 15 | AVDD — Analog supply voltage |
| Pin 16 | AVSS — Analog ground |
| Pin 17 | AN0 — Analog input 0 |
| Pin 18 | AN1 — Analog input 1 |
| Pin 19 | AN2 — Analog input 2 |
| Pin 20 | AN4/CMP1A — Analog input 4 / Comparator 1 input A |
| Pin 21 | AN5/CMP1B — Analog input 5 / Comparator 1 input B |
| Pin 22 | OPA1IN+ — Op-amp 1 non-inverting input |
| Pin 23 | OPA1IN- — Op-amp 1 inverting input |
| Pin 24 | OPA1OUT — Op-amp 1 output |
| Pin 25 | OPA2IN+ — Op-amp 2 non-inverting input |
| Pin 26 | OPA2IN- — Op-amp 2 inverting input |
| Pin 27 | OPA2OUT — Op-amp 2 output |
| Pin 28 | OPA3IN+ — Op-amp 3 non-inverting input |
| Pin 29 | OPA3IN- — Op-amp 3 inverting input |
| Pin 30 | OPA3OUT — Op-amp 3 output |
| Pin 31 | VDD — Supply voltage (5V) |
| Pin 32 | VSS — Ground |
| Pin 33 | RP8/PWM2L — Remappable I/O / PWM2 Low output |
| Pin 34 | RP7/PWM2H — Remappable I/O / PWM2 High output |
| Pin 35 | RP6/PWM4L — Remappable I/O / PWM4 Low output |
| Pin 36 | RP5/PWM4H — Remappable I/O / PWM4 High output |
| Pin 37 | RP4/PWM6L — Remappable I/O / PWM6 Low output |
| Pin 38 | RP3/PWM6H — Remappable I/O / PWM6 High output |
| Pin 39 | RP2/SCL1 — Remappable I/O / I2C1 clock |
| Pin 40 | RP1/SDA1 — Remappable I/O / I2C1 data |
| Pin 41 | RP0/INT0U — Remappable I/O / External interrupt 0 |
| Pin 42 | FLTx1 — PWM fault input 1 |
| Pin 43 | FLTx2 — PWM fault input 2 |
| Pin 44 | SENTx1 — SENT peripheral (SAE J2716) input/output |
| Pin 45 | SENTx2 — SENT peripheral (SAE J2716) input/output |
| Pin 46 | CAN1TX — CAN 1 transmit |
| Pin 47 | CAN1RX — CAN 1 receive |
| Pin 48 | U1TX — UART 1 transmit |
| Pin 49 | U1RX — UART 1 receive |
| Pin 50 | SCK1 — SPI 1 clock |
| Pin 51 | SDI1 — SPI 1 data in |
| Pin 52 | SDO1 — SPI 1 data out |
| Pin 53 | SS1 — SPI 1 slave select |
| Pin 54 | TDO — JTAG test data out (boundary scan) |
| Pin 55 | TDI — JTAG test data in |
| Pin 56 | TMS — JTAG test mode select |
| Pin 57 | TCK — JTAG test clock |
| Pin 58 | VDD — Supply voltage (5V) |
| Pin 59 | VSS — Ground |
| Pin 60 | RP16/SCLx — Remappable I/O / secondary I2C clock |
| Pin 61 | RP17/SDAx — Remappable I/O / secondary I2C data |
| Pin 62 | RP18 — Remappable I/O |
| Pin 63 | RP19 — Remappable I/O |
| Pin 64 | RP20 — Remappable I/O |
Typische Anwendungen
DSPIC33EV128GM006-I/PT ist geeignet für 6 Anwendungs: BLDC / PMSM Motor Drive, Automotive Sensor and Touch Control Unit, Appliance Control Board (Washing Machine / Dishwasher / Refrigerator), Industrial Power Supply and Inverter Control, Harsh-Environment Industrial Sensor Node, Audio Amplifier and DSP Front-End.
BLDC / PMSM Motor Drive
The DSPIC33EV128GM006-I/PT is purpose-built for sensorless or sensored 3-phase motor drives. Its 6 motor-control PWM channels with programmable dead-time and fault inputs directly drive the gate drivers of a 3-phase inverter, while the 3 on-chip operational amplifiers provide low-side current sensing without external op-amps. The 70 MIPS dsPIC core executes field-oriented control (FOC) loops well within the typical 10-20 kHz PWM cycle, and the 5V analog rails tolerate the noisy switching environment of an inverter board. Per the Microchip family data sheet DS70005144H, this device is one of the recommended controllers for appliance and HVAC blower motors as well as small industrial pumps, where its integrated analog chain reduces BOM and PCB area.
Empfohlen
Automotive Sensor and Touch Control Unit
The on-chip CTMU (Charge Time Measurement Unit) and SENT peripheral (SAE J2716) make the DSPIC33EV128GM006-I/PT well-suited to automotive sensor and HMI touch modules. CTMU enables robust capacitive touch sensing for control panels without an external touch IC, while SENT provides a single-wire, point-to-point automotive sensor interface used by throttle pedals, mass airflow sensors and similar actuators. The 5V I/O matches automotive battery rail requirements after the usual TVS/transient protection, and ECC Flash supports the functional-safety documentation package that OEMs increasingly require. The I-grade temperature range covers cabin and most under-hood-adjacent environments, with the E-grade variant extending coverage to engine-mounted locations.
Empfohlen
Appliance Control Board (Washing Machine / Dishwasher / Refrigerator)
Modern appliance main boards combine a motor-control inverter, user keypad, sensor readout, and communication interfaces in a single MCU. The DSPIC33EV128GM006-I/PT consolidates all of these functions: 6 motor-control PWMs drive the BLDC drum or compressor motor, the CTMU handles capacitive touch buttons on the front panel, the 12-bit ADC reads temperature and water-level sensors, and the on-chip op-amps condition analog signals. The 5V supply tolerance means the MCU can be powered directly from a 5V LDO fed by a 12-24V SMPS, simplifying the power tree. The 128 KB Flash accommodates IEC 60730 class B self-test routines needed for white-goods safety certification, as referenced in Microchip appliance reference designs.
Empfohlen
Industrial Power Supply and Inverter Control
Industrial AC-DC, DC-DC and solar inverters require a control MCU capable of running DSP-grade control loops (voltage-mode, current-mode, MPPT) at high PWM rates while also handling communications, housekeeping and fault management. The 70 MIPS dsPIC33EV core executes average-current-mode control at 50-100 kHz switching frequencies with substantial headroom for housekeeping tasks. The 5V analog front end interfaces directly with current-sense amplifiers and Hall-effect sensors without level translation, which is a notable BOM and noise-immunity win in 24V/48V industrial systems. Combined with the functional-safety documentation package, this makes the device a fit for industrial PSU digital control stages.
Empfohlen
Harsh-Environment Industrial Sensor Node
Factory-floor sensor nodes must operate reliably in the presence of electrical noise, vibration and extended temperature. The 5V-tolerant DSPIC33EV128GM006-I/PT interfaces directly to legacy 5V industrial logic and to noisy 4-20 mA current loops via the on-chip op-amps used as input protection/conditioning stages. The dsPIC33EV family is explicitly characterized for industrial noise immunity, with hardware peripherals like DMA, ECC Flash and CTMU that offload the CPU and tolerate transient EMI events. Communications peripherals (UART, SPI, I2C, CAN, SENT) cover the fieldbus and sensor interfaces typical of process-control nodes, and the 64-pin TQFP footprint is well-supported across PCB assembly partners.
Empfohlen
Audio Amplifier and DSP Front-End
The dsPIC DSC core's 70 MIPS throughput and dedicated MAC/DSP instructions allow the DSPIC33EV128GM006-I/PT to perform real-time audio processing - digital crossovers, equalization, dynamics control, and class-D feedback loops - that benefit from the deterministic 5V-tolerant analog chain. The 6 PWM channels can drive a class-D audio amplifier output stage directly, while the on-chip 12-bit ADC and op-amps sample the feedback signal for closed-loop class-D control. The 5V supply simplifies integration with analog audio front-end stages that expect +/-5V or single-supply 5V signal swings. This application is less common than motor control but is documented in Microchip class-D reference designs for prosumer audio and subwoofer amplifiers.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für DSPIC33EV128GM006-I/PT – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | DSPIC33EV128GM006-E/PT | DSPIC33EP64GS805-I/PT | DSPIC33EP512GM604-I/PT | dsPIC33EP512GM306-I/PT | DSPIC33EP256MC506-E/PT | DSPIC33EP512MC806-E/PT |
|---|---|---|---|---|---|---|---|
| Package | TQFP-64 (10x10 mm) | TQFP-64 (10x10 mm) - same | TQFP-64 (10x10 mm) - same | TQFP-64 (10x10 mm) - same | TQFP-64 (10x10 mm) - same | TQFP-64 (10x10 mm) - same | TQFP-64 (10x10 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core | dsPIC33EV 16-bit DSC, 70 MIPS | dsPIC33EV, 70 MIPS - identical | dsPIC33EP 16-bit DSC, 70 MIPS | dsPIC33EP 16-bit DSC, 70 MIPS | dsPIC33EP 16-bit DSC, 70 MIPS | dsPIC33EP 16-bit DSC, 70 MIPS | dsPIC33EP 16-bit DSC, 70 MIPS |
| Flash Memory | 128 KB | 128 KB | 64 KB (-50%) | 512 KB (+300%) | 512 KB (+300%) | 256 KB (+100%) | 512 KB (+300%) |
| Supply Voltage | 4.5 - 5.5 V (5V nominal) | 4.5 - 5.5 V (5V) | 3.0 - 3.6 V (3.3V) | 3.0 - 3.6 V (3.3V) | 3.0 - 3.6 V (3.3V) | 3.0 - 3.6 V (3.3V) | 3.0 - 3.6 V (3.3V) |
| On-chip Op-Amps | 3 | 3 | 0 | 0 | 0 | 0 | 0 |
| Operating Temperature | -40 C to +85 C (I grade) | -40 C to +125 C (E grade) | -40 C to +85 C (I grade) | -40 C to +85 C (I grade) | -40 C to +85 C (I grade) | -40 C to +125 C (E grade) | -40 C to +125 C (E grade) |
Wichtigste Unterscheidungsmerkmale
- Integrated 5V analog chain (3 op-amps + CTMU + 5V ADC) in a single TQFP-64 DSC (vs. DSPIC33EP64GS805-I/PT)
- Same-family temperature grade option covers -40 C to +125 C without engine or pinout change (vs. DSPIC33EV128GM006-I/PT (industrial))
- SENT (SAE J2716) peripheral for automotive sensor networks (vs. DSPIC33EP256MC506-E/PT)
Designhinweise
The DSPIC33EV128GM006-I/PT operates from a single 5V supply on VDD/AVDB (4.5-5.5 V). Place a 10 uF bulk capacitor plus a 0.1 uF ceramic decoupling capacitor as close as possible to every VDD/VSS pair, and a separate 0.1 uF + 10 uF pair on AVDB/AVSS to keep analog reference noise below the ADC's LSB. In noisy motor-control boards, a pi-filter (ferrite + cap on each side) on the 5V rail feeding AVDB is recommended to keep switching noise out of the on-chip op-amps and ADC.
For the 64-pin TQFP package, route all 6 PWM outputs as matched-length, impedance-controlled traces to the gate-driver inputs to avoid duty-cycle skew across phases. Keep the OSC1/OSC2 traces short and surrounded by a ground guard ring. The on-chip op-amp inputs and outputs are analog - route them away from PWM switching traces and gate-driver return paths; a small ground island around each op-amp pin pair is a typical best practice for low-side current sensing.
Estimated: At maximum core activity with all op-amp tails active and peripherals enabled, internal power dissipation is typically below 0.5 W, which gives a junction temperature rise of roughly 25 C above ambient for the 64-pin TQFP (theta_JA approximately 50 C per Kith on a 4-layer PCB with thermal pad copper pour). The I-grade -40 C to +85 C specification is straightforward to meet in well-ventilated appliance enclosures; in sealed IP65 housings, derate by 10-15 C or specify the E-grade variant.
Three pitfalls to avoid: (1) PPS remappable pins cannot host all peripherals - check Section 11.5 of the family data sheet DS70005144H for fixed-function pin restrictions before finalizing PCB layout. (2) The CTMU requires a stable, low-drift reference current source; an external precision resistor on the CTMU reference pin is required for accurate timing. (3) The 5V supply does not mean the I/O pins are 5V-tolerant when VDD is off - observe absolute maximum ratings if signals can be present before MCU power-up, otherwise add external TVS protection.
Compliance-Informationen
RoHS and REACH compliant per Microchip product page; I-grade is not AEC-Q100 qualified (choose E-grade or V-grade for AEC-Q100). Functional Safety (FuSa) documentation package available for the dsPIC33EV GM family.
