DSPIC33FJ32MC204T-I/PT - 40 MIPS 16-bit DSC 32KB Flash | Microchip
Teilenummer: DSPIC33FJ32MC204T-I/PT ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $5.32 | $5,32 |
| 10 | $4.85 | $48,50 |
| 100 | $4.2 | $420,00 |
| 500 | $3.9 | $1.950,00 |
| 1.000 | $3.65 | $3.650,00 |
DSPIC33FJ32MC204T-I/PT Übersicht
A Digital Signal Controller combines the compute architecture of a microcontroller with DSP-grade math peripherals such as a hardware multiply-accumulate (MAC) unit and barrel shifter. Within the power-management hierarchy, a DSC sits above a general-purpose MCU and below a dedicated DSP, making it the preferred controller class for closed-loop motor control, digital power conversion, and sensor-heavy embedded systems.
Key features include two PWM generators with independent timebases for motor and power-conversion topologies, Peripheral Pin Select (PPS) that remaps digital peripherals to arbitrary pins for layout flexibility, high-speed analog with multiple ADC inputs and up to four high-speed comparators with direct DAC-reference connection, and 40 MIPS execution from Flash with DSP instruction support.
Architecturally, the dsPIC33F core is a 16-bit pipelined RISC engine extended with DSP instructions; at 40 MHz internal clock operation it achieves 40 MIPS, and the barrel shifter accelerates bit manipulation in control loops. The family offers seamless migration to and from PIC24F, PIC24H, and dsPIC30F devices, protecting software investment.
Typical applications include brushless DC and PMSM motor drives, digital power supplies (LLC, totem-pole PFC), and industrial automation nodes requiring deterministic control loops - the independent PWM timebases and fast comparators map directly onto these use cases.
Design consideration: the 3.0-3.6 V supply requires a clean LDO or buck-derived 3.3 V rail, and PPS pin remapping must be verified at board bring-up since incorrect mapping is a common startup fault.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Drop-in-Alternativen für DSPIC33FJ32MC204T-I/PT – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit DSPIC33FJ32MC204T-I/PT (gleiche Bauform und Footprint) – abweichend in RoHS Status, Supply Voltage, Core Architecture, High-Speed Comparators, I/O Ports.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
DSPIC33FJ32MC204T-E/PT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
DSPIC33FJ32MC204T-H/PT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
DSPIC33FJ32MC204-I/PT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
DSPIC33FJ32GP204-I/PT
✅ Drop-In✓ Auf Lager
$3.78 / Stück
Datenblatt ansehen →DSPIC33FJ32GP204-E/PT
✅ Drop-In✓ Auf Lager
$3.15 / Stück
Datenblatt ansehen →DSPIC33FJ32MC204T-I/PT Grenzwerte & elektrische Eigenschaften
| Core | 16-bit dsPIC33F RISC with DSP extensions |
| Max Clock Speed | 40 MHz |
| Performance | 40 MIPS |
| Flash Program Memory | 32 KB |
| SRAM | 2 KB |
| Versorgungsspannung | 3 V to 3.6 V |
| I/O Ports | 35 |
| PWM Generators | 2 with independent timebases |
| High-Speed Comparators | Up to 4 with direct DAC reference connection |
| Peripheral Pin Select (PPS) | Yes |
| Gehäuse | TQFP-44 (10 x 10 mm, 1 mm height, 0.80 mm pitch) |
| Montageart | Surface Mount |
| Betriebstemperatur | -40C to +85C (I grade, industrial) |
| Packing | Tape and Reel (T suffix) |
| ROM Type | Flash |
| Lead Finish | Lead free |
| Family Migration | PIC24F, PIC24H, dsPIC30F compatible |
| RoHS-Status | Compliant |
DSPIC33FJ32MC204T-I/PT tqfp-44 (10 x 10 mm, 1 mm height, 0.80 mm pitch) Pinbelegungsleitfaden
Pinbelegung für DSPIC33FJ32MC204T-I/PT (tqfp-44 (10 x 10 mm, 1 mm height, 0.80 mm pitch)-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für DSPIC33FJ32MC204T-I/PT.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
DSPIC33FJ32MC204T-I/PT ist geeignet für 6 Anwendungs: BLDC / PMSM Motor Drives, Digital Power Supplies (LLC / PFC), Industrial Automation Nodes, Battery-Powered Portable Instruments, Robotics and Servo Control, HVAC and Appliance Motor Control.
BLDC / PMSM Motor Drives
The DSPIC33FJ32MC204T-I/PT was architected for precision motor control: its two PWM generators with independent timebases produce the complementary or independent PWM patterns required for trapezoidal and field-oriented control of brushless DC and permanent-magnet synchronous motors. The high-speed comparators with direct DAC reference connection enable hardware-level overcurrent protection and cycle-by-cycle current limiting without CPU latency, while multiple ADC channels support simultaneous phase-current sensing. Running at 40 MIPS, the device closes FOC current loops well within typical 50-100 us PWM periods. Peripheral Pin Select simplifies routing encoder and PWM signals on dense 44-pin layouts. Trade-off: at 32 KB Flash, only one moderate-complexity FOC stack plus communication fits - plan memory accordingly.
Empfohlen
Digital Power Supplies (LLC / PFC)
In LLC converters and totem-pole PFC stages, the DSPIC33FJ32MC204T-I/PT supplies the deterministic 40 MIPS core needed for frequency and phase modulation at switching frequencies of 100 kHz and above. The two independent-timebase PWM generators can drive the half-bridge legs with programmable dead time, while the up-to-four high-speed comparators with direct DAC references implement fast peak-current limiting in hardware. The ADC sequence supports sensing of input/output voltage and current within one switching cycle. The 3.0-3.6 V logic domain interfaces cleanly with gate-driver logic levels. Design consideration: reserve one PWM timebase for auxiliary housekeeping fly-bias supply control to avoid CPU-interrupt-driven switching.
Empfohlen
Industrial Automation Nodes
Factory automation nodes - sensor aggregators, actuator controllers, and small PLC I/O modules - benefit from the DSPIC33FJ32MC204T-I/PT's 35 I/O pins with Peripheral Pin Select, which lets one PCB serve multiple node variants by remapping UART, SPI, and PWM pins in firmware. The 40 MIPS 16-bit core with DSP MAC handles filtering of noisy sensor channels (IIR/FIR at kHz rates) while maintaining a Modbus or CAN-over-UART link. The industrial -40C to +85C temperature grade matches cabinet environments. Flash-based program memory supports field updates. For applications exceeding +85C near motors or heaters, the drop-in E-grade variant extends the range to +125C without PCB changes.
Empfohlen
Battery-Powered Portable Instruments
Handheld instrumentation and battery-operated controllers fit the DSPIC33FJ32MC204T-I/PT's 3.0-3.6 V single-rail operation, which runs directly from a single-cell boost or two-cell LDO topology. The 16-bit core executes measurement math efficiently at reduced clocks for power savings, and the device supports low-power modes for duty-cycled acquisition. The DSP MAC accelerates RMS, FFT pre-processing, and digital filtering on captured analog data, while on-chip comparators provide threshold alarms without CPU wakeups. The 10 x 10 mm TQFP-44 balances pin count against board area in handheld enclosures. Note the 2 KB SRAM limit: scope long data-acquisition buffers carefully or stream to external memory.
Empfohlen
Robotics and Servo Control
Small robotic manipulators and smart servo drives use the DSPIC33FJ32MC204T-I/PT to close position, velocity, and current loops simultaneously: the dual independent-timebase PWM generators drive H-bridges for multiple axes or one high-resolution axis with complementary outputs, the ADC samples hall sensors or encoders, and the 40 MIPS core runs cascaded PID or field-oriented inner loops. Hardware comparators implement stall-current protection deterministically. Peripheral Pin Select allows a common PCB to serve left/right joint variants via firmware. Seamless migration to PIC24/dsPIC30F families protects code as axis count grows into larger dsPIC33F parts with the same peripheral architecture.
Empfohlen
HVAC and Appliance Motor Control
Compressor, blower, and fan motors in HVAC and white-goods products are increasingly driven by sensorless FOC or sinusoidal BLDC schemes implemented on the DSPIC33FJ32MC204T-I/PT. Its high-speed comparators and ADC handle back-EMF zero-crossing or shunt-current sensing, while the independent-timebase PWMs generate low-acoustic-noise sinusoidal drive. The industrial temperature grade and lead-free RoHS-compliant TQFP-44 suit appliance qualification environments. The 32 KB Flash holds sensorless estimation algorithms plus a communication interface (UART or I2C to the appliance master controller). Derating note: place the DSC away from hot chassis zones or select the +125C E-grade drop-in variant for compartment mounting.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für DSPIC33FJ32MC204T-I/PT – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | DSPIC33FJ32MC204T-E/PT | DSPIC33FJ32MC204T-H/PT | DSPIC33FJ32MC204-I/PT | DSPIC33FJ32GP204-I/PT | DSPIC33FJ32GP204-E/PT |
|---|---|---|---|---|---|---|
| Package | TQFP-44 (10 x 10 mm) | TQFP-44 - same | TQFP-44 (PQFP44) - same | TQFP-44 - same | TQFP-44 - same | TQFP-44 - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash / SRAM | 32 KB / 2 KB | 32 KB / 2 KB | 32 KB / 2 KB | 32 KB / 2 KB | 32 KB / 2 KB | 32 KB / 2 KB |
| Performance | 40 MIPS at 40 MHz | 40 MIPS | 40 MIPS | 40 MIPS | 40 MIPS | 40 MIPS |
| Motor-Control PWM (independent timebases) | Yes (2 generators) | Yes (2 generators) | Yes (2 generators) | Yes (2 generators) | No (GP family PWM set) | No (GP family PWM set) |
| Operating Temperature | -40C to +85C (I) | -40C to +125C (E) | High-temp grade (H) | -40C to +85C (I) | -40C to +85C (I) | -40C to +125C (E) |
Wichtigste Unterscheidungsmerkmale
- Motor-control PWM with independent timebases (vs. DSPIC33FJ32GP204-I/PT)
- Extended temperature drop-in upgrade path (vs. DSPIC33FJ32MC204T-E/PT)
- Peripheral Pin Select flexibility (vs. DSPIC33FJ32MC202 (28-pin siblings))
Designhinweise
The DSPIC33FJ32MC204T-I/PT requires a single 3.0-3.6 V rail. In motor-drive systems where a 5 V or 24 V bus exists, derive 3.3 V with a low-noise LDO (e.g., an MCP-series or similar) placed away from gate-driver switching noise. Decouple every VDD pin pair with 0.1 uF ceramic capacitors placed within 2 mm of the pins, plus one bulk 4.7-10 uF per device. Follow Microchip's power-up requirements: VDD must rise monotonically and MCLR should be held low via an RC network until the rail stabilizes.
On a 44-pin TQFP (0.80 mm pitch), route PWM outputs away from ADC input traces to prevent switching coupling into current-sense channels; use a ground plane under the device and return analog grounds to a single star point. Peripheral Pin Select (PPS) gives layout freedom - exploit it to keep crystal, analog, and PWM nets short rather than forcing peripheral assignment early. Keep the oscillator traces under 15 mm with guard ground if using an external crystal for the PLL-based 40 MHz clock.
The most common bring-up failures on this family are: (1) forgetting that PPS remapping must be written and locked before peripherals function, (2) exceeding the 3.6 V absolute maximum by connecting 5 V logic directly to I/O - always level-shift, and (3) selecting the I grade for environments above +85C. If the controller sits near power semiconductors, choose the drop-in DSPIC33FJ32MC204T-E/PT rated to +125C instead of redesigning for heatspreading. Also configure unused I/O as outputs-low to avoid floating-pin EMI.
Compliance-Informationen
Distributor specification data describes the TQFP-44 package as lead-free plastic; RoHS compliant per Microchip product offering. Not AEC-Q100 automotive qualified per available data. REACH/halogen status not stated in provided data.
