FAN7383MX - 600V Half-Bridge Gate Driver, 14-SOP | onsemi
Teilenummer: FAN7383MX ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $1.18 | $1,18 |
| 10 | $1.04 | $10,40 |
| 100 | $0.84 | $84,00 |
| 500 | $0.69 | $345,00 |
| 1.000 | $0.58 | $580,00 |
| 3.000 | $0.49 | $1.470,00 |
FAN7383MX Übersicht
A half-bridge gate driver is a type of FET/IGBT driver (a sub-category of power management ICs) that supplies the high peak gate charge currents required to switch the high-side switch of a synchronous half-bridge or full-bridge power stage. Compared to gate-drive transformers or bootstrap-only discrete designs, an integrated half-bridge driver IC such as the FAN7383MX adds level shifting, a stable bootstrap diode for the high-side rail, dead-time insertion to prevent shoot-through, and logic-level PWM input compatibility - replacing dozens of discrete components with one IC.
Key features include 600V high-side offset voltage (allowing operation on 400V-class rectified bus rails), built-in common-mode noise cancellation for stable high-dv/dt operation, an SD (shutdown) input, and a programmable dead-time range that optimizes turn-on/turn-off timing for MOSFET or IGBT switches. The 14-SOP footprint gives it a small board area while still allowing conventional hand-soldering and visual inspection, which is uncommon for high-voltage gate drivers that are typically SOIC-8 or smaller.
Architecturally, the FAN7383MX uses onsemi's high-voltage BCD process with an advanced level-shift circuit that translates the PWM input reference (ground) to the floating high-side rail, plus a noise-canceling technique that rejects the large dV/dt transients seen on the switching node (HS pin). The DT pin sources a current set by R_DT through an internal resistor network, which controls the dead time between HO and LO transitions.
Typical applications include 3-phase inverter motor drives (HVAC compressors, small industrial fans, washing-machine variable-frequency drives), half-bridge and full-bridge switch-mode power supplies (telecom rectifiers, server PSUs), electronic ballasts for fluorescent and HID lighting, induction-heating cooktops, and solar micro-inverter half-bridge stages.
When designing with this part, choose the dead-time resistor R_DT to be slightly longer than the switch turn-off delay to prevent cross-conduction; too long a dead-time wastes body-diode conduction time and increases losses. The bootstrap capacitor CBST must be sized to supply the high-side gate charge plus quiescent current across the longest PWM off-time, and the VBS supply should be locally decoupled with a ceramic bypass capacitor.
This page synthesizes distributor pricing, same-brand and cross-brand drop-in equivalents, and practical design notes that are not found in the onsemi datasheet alone, giving you a single engineering reference for the FAN7383MX.
Drop-in-Alternativen für FAN7383MX – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
FAN7383M
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
FAN7383MX Grenzwerte & elektrische Eigenschaften
| Driver Type | Half-Bridge Gate Driver (single PWM input, HO/LO outputs) |
| Anzahl der Ausgänge | 2 (high-side HO, low-side LO) |
| High-Side Offset Voltage (V_B - V_S) | 600 V (max) |
| Sink Current (I_OUT, typ) | 0.65 A |
| Source Current (I_OUT, typ) | 0.35 A |
| Configuration | Non-Inverting |
| Input Logic | Single PWM (HIN/LIN logic input) |
| Dead-Time Control | Programmable via external resistor R_DT at DT pin |
| Shutdown Pin | Yes (SD, active) |
| Bootstrap Drive | Built-in bootstrap diode / high-side floating supply |
| Common-Mode dV/dt Noise Cancellation | Yes (internal) |
| Supply Voltage (V_CC, V_BS) | 10 V to 20 V (typical 15 V) |
| Betriebstemperaturbereich | -40C to +125C |
| Gehäuse | 14-pin SOP (SOIC-14, 3.90 mm body width) |
| Montageart | Surface Mount |
| MSL-Level | 3 (per JEDEC J-STD-020) |
| RoHS-Status | Compliant |
FAN7383MX Pin-Konfiguration
| Pin 1 | VCC — Low-side and logic supply voltage (10V-20V, typ 15V) |
| Pin 2 | HIN — Logic input for high-side output (HO); non-inverting |
| Pin 3 | LIN — Logic input for low-side output (LO); non-inverting |
| Pin 4 | DT — Dead-time programming pin; connect R_DT to GND to set HO/LO non-overlap |
| Pin 5 | GND — Ground reference for low-side driver and logic |
| Pin 6 | LO — Low-side gate-drive output (drives low-side MOSFET/IGBT gate) |
| Pin 7 | NC — Not connected (no internal bond) |
| Pin 8 | VS — High-side floating supply return; connected to half-bridge switching node |
| Pin 9 | VB — High-side floating supply (bootstrap rail referenced to VS) |
| Pin 10 | NC — Not connected (no internal bond) |
| Pin 11 | HO — High-side gate-drive output (drives high-side MOSFET/IGBT gate) |
| Pin 12 | NC — Not connected (no internal bond) |
| Pin 13 | VBS — Bootstrap supply pin (VB + internal diode tied to VCC); also referred to as V_BS |
| Pin 14 | SD — Shutdown input; logic level to disable both HO and LO outputs |
Typische Anwendungen
FAN7383MX ist geeignet für 6 Anwendungs: 3-Phase Variable-Frequency Motor Drive (HVAC Compressor / Fan), Half-Bridge / Full-Bridge Switch-Mode Power Supply, Electronic Ballast for Fluorescent / HID Lighting, Induction-Heating Cooktop Half-Bridge Stage, Solar Micro-Inverter Half-Bridge Stage, Battery-Powered Wireless / Portable Tool BLDC Drive.
3-Phase Variable-Frequency Motor Drive (HVAC Compressor / Fan)
The FAN7383MX drives one half-bridge leg of a 3-phase VFD inverter for HVAC compressors, industrial fans, and washing-machine variable-frequency motors up to roughly 1-3 kW. Its 600V high-side offset tolerates a 400V rectified DC bus, the 0.65A sink current switches most 600V-class IGBTs cleanly, and the programmable DT pin lets the designer tune dead-time to the specific IGBT turn-off delay. Use three FAN7383MX ICs to drive all three half-bridge legs; pair with bootstrap caps sized for the longest PWM off-time plus VBS quiescent current.
Empfohlen
Half-Bridge / Full-Bridge Switch-Mode Power Supply
In telecom and server half-bridge or full-bridge SMPS stages the FAN7383MX drives the primary-side MOSFETs from a 400V bus. The built-in dead-time control (R_DT at DT pin) prevents shoot-through between the high-side and low-side MOSFETs, and the 14-SOP package allows conventional hand-soldering and visual inspection during prototyping. Use a bootstrap diode to VBS and a local ceramic bypass on VCC for clean switching under high dV/dt on the switching node.
Empfohlen
Electronic Ballast for Fluorescent / HID Lighting
Electronic ballasts for fluorescent tubes and HID lamps use a half-bridge resonant inverter operating from a rectified mains bus. The FAN7383MX fits this topology directly: the 600V high-side rating handles the rectified 220V or 277V mains, and the 0.65A sink / 0.35A source current is sufficient for the low-current IGBTs or MOSFETs used in lamp-ballast half-bridges. The SD (shutdown) pin supports lamp-out protection by disabling both gate outputs on fault conditions.
Empfohlen
Induction-Heating Cooktop Half-Bridge Stage
Induction-heating cooktops use a resonant half-bridge to drive the heating coil at 20-100 kHz. The FAN7383MX drives the 600V-class IGBTs in this resonant tank with programmable dead-time that prevents cross-conduction during resonant zero-voltage switching transitions. The internal common-mode dV/dt noise cancellation keeps the high-side channel stable when the switching node swings at hundreds of volts per nanosecond.
Empfohlen
Solar Micro-Inverter Half-Bridge Stage
Grid-tie solar micro-inverters convert the PV panel DC output to AC through a DC-DC stage followed by a DC-AC inverter. The FAN7383MX drives the primary-side MOSFETs of the DC-DC half-bridge on a 400V-class rectified PV bus, or the line-frequency unfolding switches in the DC-AC stage. The SD pin enables fast shutdown for anti-islanding protection required by UL 1741 and IEEE 1547 grid-tie safety standards.
Empfohlen
Battery-Powered Wireless / Portable Tool BLDC Drive
Cordless power tools and battery-operated appliances use low-voltage BLDC motors; however, higher-power 18V/36V-class tools still benefit from a half-bridge gate driver to reduce MCU pin-drive losses. The FAN7383MX can be used in such applications on the low-voltage side (e.g., 48V bus) where its high-side rating provides large margin and the SD pin supports fault shutoff. The 14-SOP footprint suits compact tool-motor PCBs.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für FAN7383MX – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | FAN7383M | NCP81074BDR2G | FAN7392MX | IRS2183STRPBF | UCC27324DR |
|---|---|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | onsemi | Infineon | Texas Instruments |
| Package | 14-SOP (SOIC-14) | 14-SOP - same | 8-SOIC - DIFFERENT | 16-SOP - DIFFERENT | 8-SOIC - DIFFERENT | 8-SOIC - DIFFERENT |
| Topology | Half-bridge (single PWM input, HO+LO) | Half-bridge - same | Half-bridge - same | Half-bridge - same | Half-bridge - same | Dual non-inverting (NOT half-bridge) - DIFFERENT |
| Programmable Dead-Time | Yes (R_DT at DT pin) | Yes - same | Yes | Yes | No (fixed internal dead-time) | No (N/A dual driver) |
| Shutdown Pin | Yes (SD) | Yes - same | Yes | Yes | No | No (N/A dual driver) |
Wichtigste Unterscheidungsmerkmale
- Programmable dead-time with explicit DT pin (vs. IRS2183STRPBF)
- Compact 14-SOP package with integrated shutdown pin (vs. FAN7392MX)
- 600V high-side rating in a 14-SOP gate driver (vs. UCC27324DR)
Designhinweise
Size the bootstrap capacitor CBST to supply the high-side gate charge QG plus the VBS quiescent current IQBS over the longest PWM off-time. Rule of thumb: CBST >= (QG + IQBS * t_OFF_max) / dV_BS, with dV_BS typically allowed to drop 0.5V-1V from the regulated 15V VCC. A 0.1uF-1uF X7R ceramic is a typical starting point for 600V-class IGBTs; verify by measuring VBS ripple on the scope under worst-case duty cycle.
Setting dead-time too short causes shoot-through (both high-side and low-side switches momentarily ON) and catastrophic bus short. Setting dead-time too long increases body-diode conduction time and switching losses. The R_DT value should be chosen to provide dead-time slightly longer than the worst-case switch turn-off delay (t_off(max)) at the lowest operating temperature. The onsemi FAN7383 datasheet contains a graph of R_DT versus dead-time in nanoseconds; consult it during design.
Place the VCC bypass capacitor (typically 0.1uF X7R) within 5 mm of the VCC pin and the VBS bypass (1uF X7R) directly across VB to VS. Keep the gate-drive traces (HO, LO) short and away from the switching node (HS/VS) to minimize capacitive coupling and ringing. Use a ground plane under the low-side driver and gate-loop return paths, and consider a 4-layer PCB with a dedicated return layer if the design must pass stringent EMI tests such as CISPR 11/22.
Estimated: at continuous 100 kHz switching into a 50 nC gate charge, gate-drive losses are roughly P_gate = QG * VCC * f_sw = 50e-9 * 15 * 100e3 = 0.075 W per output, totaling ~0.15 W for both HO and LO. The 14-SOP package has theta_JA around 100-120 C/W on a 1 oz 2-layer board, giving a junction temperature rise of 15-20 C - well within the 125 C operating limit. Verify with measured case temperature in production.
Compliance-Informationen
RoHS and REACH compliance per onsemi product family page. Lead-free reflow at 260 C peak per JEDEC J-STD-020; MSL 3 per distributor listings. Halogen-free status not explicitly stated in the provided data - set to unknown.
