FT4232HQ-REEL - USB 2.0 HS to Quad UART/MPSSE Bridge | FTDI
Teilenummer: FT4232HQ-REEL ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $9.95 | $9,95 |
| 10 | $9.45 | $94,50 |
| 100 | $8.6 | $860,00 |
| 500 | $7.85 | $3.925,00 |
| 1.000 | $7.1 | $7.100,00 |
| 3.000 | $6.35 | $19.050,00 |
FT4232HQ-REEL Übersicht
A USB bridge (also called USB-to-UART or USB-to-serial bridge) is a type of interface IC that converts USB signaling from a host computer into one or more legacy serial protocols such as UART, SPI, I2C, or JTAG. Bridges sit in the hierarchy: USB bridge -> interface IC -> communication controller -> semiconductor. They are essential in modern electronics because most MCUs and FPGAs retain native UART/SPI/I2C peripherals but lack USB device controllers, while virtually every laptop, workstation, and embedded SBC exposes only USB.
Key features include hardware flow control on all UART channels, programmable baud rates up to 12 Mbaud, integrated 12 MHz to 480 MHz clock generation from a single 12 MHz crystal, full USB 2.0 Hi-Speed compliance, and a wake-up function on USB activity. The QFN-64 package offers a compact 9x9 mm footprint with an exposed thermal pad for reliable operation across the industrial -40 C to +85 C temperature range.
Internally, the FT4232HQ uses a 5th-generation USB protocol engine with on-chip PHY, 4 KB of FIFO per channel, and per-channel configurable MPSSE engines. The architecture enables simultaneous operation of, for example, a JTAG debugger on channel A, an SPI flash programmer on channel B, and two UART debug consoles on channels C and D - a combination that historically required multiple discrete bridge ICs.
Typical applications include industrial JTAG/SPI programming stations, multi-port USB-to-serial adapters for test and lab instrumentation, FPGA and MCU development boards, embedded debugging probes (CMSIS-DAP, J-Link equivalents), and point-of-sale terminals. The four-channel density also suits multi-radio debug headers and protocol-aware production testers.
When designing with this device, observe USB-IF compliance layout practices: 90-ohm differential impedance on D+/D-, ESD protection near the USB connector, decoupling on VCC and VIO, and a 12 MHz crystal with the load capacitors specified in the FTDI datasheet.
This page synthesizes FTDI-published specifications, distributor pricing, true drop-in alternatives in the QFN-64 footprint, and practical design notes not collected in any single source.
Drop-in-Alternativen für FT4232HQ-REEL – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit FT4232HQ-REEL (gleiche Bauform und Footprint) – abweichend in Package, Product Type.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
FT4232HQ
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
FT2232HQ-REEL
✅ Drop-In✓ Auf Lager
$6.75 / Stück
Datenblatt ansehen →FT232HQ-REEL
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
FT600Q-REEL
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
FT4232HQ-REEL Technische Daten
| Product Type | USB 2.0 High-Speed to Quad UART/MPSSE Bridge |
| USB Standard | USB 2.0 High-Speed (480 Mbps) |
| Number of UART Channels | 4 |
| MPSSE Engines | 2 (configurable as SPI / I2C / JTAG / bit-bang) |
| Maximum Baud Rate | 12 Mbaud |
| Supply Voltage (VBUS) | 4.0 V to 5.25 V (USB bus powered) |
| I/O Voltage (VIO) | 1.8 V to 3.3 V |
| Internal LDO Output (VCC) | 3.3 V |
| FIFO per Channel | 4 KB |
| Crystal Frequency | 12 MHz |
| Betriebstemperatur | -40 C to +85 C |
| Gehäuse | QFN-64 (9x9 mm) with exposed pad |
| Montageart | Surface Mount |
| RoHS-Status | Compliant |
| Lead-Free | Yes |
FT4232HQ-REEL qfn-64 (9x9 mm) with exposed pad Pinbelegungsleitfaden
Pinbelegung für FT4232HQ-REEL (qfn-64 (9x9 mm) with exposed pad-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für FT4232HQ-REEL.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
FT4232HQ-REEL ist geeignet für 6 Anwendungs: Industrial JTAG/SPI Programming Station, Multi-Port USB-to-Serial Adapter, FPGA and MCU Development Board Debug Bridge, Embedded Debugging Probe (CMSIS-DAP / OpenOCD), Point-of-Sale (POS) Terminal, Multi-Radio Test & Measurement Fixture.
Industrial JTAG/SPI Programming Station
The FT4232HQ-REEL fits an industrial JTAG/SPI programming station because it offers two MPSSE engines that can drive JTAG state machines up to 30 MHz while the remaining two channels serve as UART consoles for bootloader logs. Each MPSSE engine can also bit-bang custom protocols for production-line flash programming. Placed on the programmer's controller PCB with a 12 MHz crystal and a USB-C connector, the FT4232HQ-REEL eliminates the need for multiple discrete bridge ICs. The QFN-64 (9x9 mm) footprint is footprint-compatible with the FT2232HQ-REEL for hardware reuse across dual-channel and quad-channel product tiers. The exposed thermal pad supports continuous MPSSE streaming at high TCK rates without thermal throttling in the -40 C to +85 C industrial range.
Empfohlen
Multi-Port USB-to-Serial Adapter
The FT4232HQ-REEL is the heart of a four-port USB-to-serial adapter because it integrates four independent UART channels, each with hardware flow control (RTS/CTS, DTR/DSR, XON/XOFF) and programmable baud rates up to 12 Mbaud. The 4 KB per-channel FIFO prevents host-side jitter even at high baud, while FTDI's WHQL-certified VCP and D2XX drivers work on Windows, macOS, Linux, and Android without user-side recompilation. Compared to a discrete four-chip bridge solution, the FT4232HQ-REEL shrinks BOM cost and PCB area by ~70%. Industrial designers appreciate the -40 to +85 C operating range and USB-IF compliance documentation in the FTDI datasheet.
Empfohlen
FPGA and MCU Development Board Debug Bridge
The FT4232HQ-REEL is widely used on FPGA and MCU development boards because it delivers two MPSSE channels for JTAG/SPI plus two UART channels for console + data logging in a single chip. An FPGA evaluation board can route channel A to JTAG, channel B to SPI flash programmer, channel C to a UART debug console, and channel D to a second UART for peripheral debug, all over one USB connection. Compared with separate FT2232HQ plus UART bridges, the FT4232HQ-REEL cuts board area and BOM cost while supporting OpenOCD, urJTAG, and the FTDI D2XX driver stack. The QFN-64 footprint shares a land pattern with the FT2232HQ-REEL, enabling one PCB to support two-channel and four-channel variants.
Empfohlen
Embedded Debugging Probe (CMSIS-DAP / OpenOCD)
The FT4232HQ-REEL is well-suited to embedded debugging probes because the MPSSE engines natively generate JTAG/SWD/SPI timing at up to 30 MHz without external logic. OpenOCD and the CMSIS-DAP firmware stack on top of libFTDI expose channel A as a JTAG/SWD probe while channel B/C/D remain available as auxiliary UART or SPI channels. Compared to discrete MCU-based probes, an FTDI-MPSSE probe offers lower latency, better host-side driver support across Windows/macOS/Linux, and superior USB compliance per the FTDI datasheet. The industrial temperature range (-40 C to +85 C) makes the FT4232HQ-REEL appropriate for in-field debug tools.
Empfohlen
Point-of-Sale (POS) Terminal
The FT4232HQ-REEL supports point-of-sale terminals because it provides four independent serial channels that can drive a magnetic-stripe reader (UART), a thermal printer (UART), a smart-card reader (UART/SPI), and a barcode scanner (UART/HID) over a single USB host port. Hardware flow control and 12 Mbaud rates accommodate the bursty data patterns of barcode scanners and printers. The integrated 12 MHz crystal driver and 3.3 V LDO simplify the power tree, while the industrial temperature range keeps the FT4232HQ-REEL reliable in retail back-office environments. Compared to a USB hub plus four discrete bridge chips, the FT4232HQ-REEL consolidates BOM and reduces PCB area significantly.
Empfohlen
Multi-Radio Test & Measurement Fixture
The FT4232HQ-REEL serves multi-radio test fixtures where a test host needs simultaneous UART access to GPS, BLE, Wi-Fi, and sub-GHz radio modules, or to four DUTs on a parallel test bed. Each UART channel operates independently up to 12 Mbaud, with hardware flow control protecting against radio-buffer overruns, while two MPSSE channels can drive SPI-based radio configuration busses. The FTDI WHQL driver stack and Linux/Android support enable the same fixture to run on host PCs, lab instruments, and production ATE. The QFN-64 (9x9 mm) package and exposed pad simplify thermal management under continuous 12 Mbaud streaming loads.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für FT4232HQ-REEL – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | FT4232HQ | FT2232HQ-REEL | FT232HQ-REEL | FT600Q-REEL |
|---|---|---|---|---|---|
| Brand | FTDI | FTDI | FTDI | FTDI | FTDI |
| Package | QFN-64 (9x9 mm) | QFN-64 (9x9 mm) - same | QFN-64 (9x9 mm) - same | QFN-64 (9x9 mm) - same | QFN-64 (9x9 mm) - same |
| USB Standard | USB 2.0 Hi-Speed (480 Mbps) | USB 2.0 Hi-Speed (480 Mbps) | USB 2.0 Hi-Speed (480 Mbps) | USB 2.0 Hi-Speed (480 Mbps) | USB 3.0 SuperSpeed (5 Gbps) |
| Number of UART Channels | 4 | 4 | 2 (-50%) | 1 (-75%) | 0 (FIFO only) |
| MPSSE Engines | 2 | 2 | 2 | 1 | 0 |
| Maximum Baud Rate | 12 Mbaud | 12 Mbaud | 12 Mbaud | 12 Mbaud | N/A (parallel FIFO) |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
Wichtigste Unterscheidungsmerkmale
- Four serial channels in a single QFN-64 footprint (vs. FT2232HQ-REEL)
- Two MPSSE engines vs one (vs. FT232HQ-REEL)
- Mature, broadly-supported VCP/D2XX driver stack (vs. CP2108 (Silicon Labs))
- Backward compatible with FT2232H/FT232H land patterns (vs. CP2108)
Designhinweise
Route the USB D+ and D- differential pair on the top layer with 90-ohm differential impedance and length matching within 150 mil per the FTDI datasheet USB compliance section. Place the 12 MHz crystal and its 27 pF (or per datasheet) load capacitors within 5 mm of the XIN/XOUT pins. Tie the exposed thermal pad to a contiguous ground copper pour with at least 8 thermal vias to the inner ground plane to keep the QFN-64 junction temperature within spec during continuous MPSSE streaming.
The FT4232HQ-REEL derives its internal 3.3 V LDO from VBUS (4.0-5.25 V). Add a 4.7 uF bulk capacitor and a 100 nF decoupling capacitor close to VBUS, and a 100 nF + 4.7 uF combination on VCC (3V3OUT) per the FTDI reference schematic. For self-powered designs, ensure VBUS sees 5 V only after the upstream USB cable is detected and never back-feed 3.3 V into VCC from the host side.
Do not leave the RESET# pin floating - tie it to VCC through a 10 kohm pull-up if unused, or drive it from a host GPIO for firmware recovery. The CBUS pins are factory-configurable; verify your CBUS mapping against the FTDI FT_PROG utility settings rather than assuming default behaviour. The EEPROM-less variant differs from the EEPROM variant at power-on, so confirm whether your BOM specifies FT4232HQ or FT4232HQ-E before placing the order.
For EMI, place a common-mode choke on the D+/D- pair as close to the USB connector as practical, especially if the enclosure is unshielded or the cable exceeds 1 m. Use a USB-IF-certified ESD protection diode array (e.g., 5 V working voltage, low capacitance) at the connector to protect the FT4232HQ-REEL from cable-discharge events. Series ferrite beads on VBUS can suppress conducted noise from upstream hubs.
Compliance-Informationen
RoHS and REACH compliant per FTDI product page. USB 2.0 Hi-Speed certified by USB-IF; not AEC-Q100 qualified (industrial -40 to +85 C, not automotive).
