KSZ8893MBL - 3-Port 10/100 Managed Switch | Microchip
Teilenummer: KSZ8893MBL ✓ AktivKSZ8893MBL Übersicht
An Ethernet switch is a networking semiconductor that receives Ethernet frames on one port and forwards them to the appropriate destination port. The KSZ8893 belongs to the managed-switch hierarchy, where Layer 2 switching is combined with traffic-management functions rather than basic frame replication. Its management capabilities include rate limiting, tag- and port-based VLAN support, QoS priority, MIB counters, and CPU control and data interfaces.
The KSZ8893MQL and KSZ8893MBL versions integrate three 10/100 Ethernet PHYs with a managed switching engine. Supporting RMII, MII, and SNI interfaces allows connection to a host processor or network controller. I2C and SPI host interfaces provide access to configuration and status registers, while frame buffers support the managed-switch architecture. These functions make the device suitable for compact industrial, embedded, and communications equipment requiring three Ethernet ports without a discrete switch ASIC.
The KSZ8893MBL is particularly useful where port count is intentionally low and board area is constrained. Its 100-LFBGA package supports dense multilayer layouts, but it requires careful escape-routing and high-speed layout techniques. Differential Ethernet pairs should be routed as controlled-impedance transmission lines, with magnetics or appropriate PHY-side network interfaces implemented according to the system reference design.
Typical uses include industrial controllers, embedded logging equipment, computing modules, factory automation nodes, serial-to-Ethernet systems, and compact network access products. In these applications, the integrated PHYs reduce the number of external Ethernet magnetics and interface components while managed features allow traffic prioritization and controlled access to shared uplink bandwidth.
The primary design consideration is that the MBL ordering code and its 100-pin LFBGA land pattern must be matched exactly during PCB and assembly planning. Power, ground, RMII or MII signals, management buses, and all three Ethernet channels require careful partitioning. Compliance and exact operating limits should be confirmed against the manufacturer datasheet before production release.
This page consolidates the verified distributor information, manufacturer documentation, package constraints, pricing indicator, and available cross-reference evidence. It also distinguishes the KSZ8893MBL from related ordering codes and clearly identifies engineering data that still requires confirmation from the full manufacturer datasheet.
Drop-in-Alternativen für KSZ8893MBL – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
KSZ8893MBLI
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →KSZ8893MBL Grenzwerte & elektrische Eigenschaften
| Product Type | 3-Port Layer 2 Managed Ethernet Switch with PHYs |
| Number of Ports | 3 ports |
| Ethernet Data Rate | 10/100 Mbps |
| Supported Ethernet Media | 10/100 Base-FX, Base-T, and Base-TX |
| Integrated PHYs | 3 integrated 10/100 PHYs |
| Host Interface | RMII/MII/SNI |
| Management Interface | I2C and SPI |
| Switching Layer | Layer 2 |
| VLAN Support | Tag-based and port-based VLAN |
| QoS Support | QoS priority |
| Traffic Management | Rate limiting |
| Management Statistics | MIB counters |
| CPU Interface | CPU control and data interfaces |
| Gehäuse | 100-pin LFBGA |
| Montageart | Surface Mount |
KSZ8893MBL 100-pin lfbga Pinbelegungsleitfaden
Pinbelegung für KSZ8893MBL (100-pin lfbga-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für KSZ8893MBL.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
KSZ8893MBL ist geeignet für 6 Anwendungs: Industrial Ethernet Controllers, Embedded Logging and Monitoring, Compact Network Access Products, Factory Automation Communication Hubs, Computing Module Connectivity, Serialized Device Networking.
Industrial Ethernet Controllers
The KSZ8893MBL fits industrial controllers that need three 10/100 Mbps Ethernet links without allocating space for a larger switch ASIC. Its integrated PHYs reduce the number of external network-interface stages, while rate limiting, VLAN, QoS priority, and MIB counters provide useful control over shared industrial traffic. RMII, MII, and SNI connectivity lets the switch connect to different host-controller architectures. The 100-pin LFBGA package supports dense equipment designs, although careful differential-pair routing, solid ground-plane planning, and package escape routing are essential for reliable Ethernet performance.
Empfohlen
Embedded Logging and Monitoring
The KSZ8893MBL is appropriate for embedded logging and monitoring equipment that must aggregate data from several 10/100 Ethernet endpoints. Three integrated PHYs allow local devices, a management computer, and an uplink to share one managed Layer 2 platform. Tag- and port-based VLAN support can separate operational traffic, while QoS priority can favor monitoring packets over less time-sensitive background transfers. MIB counters support remote supervision, and I2C or SPI management simplifies integration with an embedded controller. These functions make the part more useful than a basic unmanaged switch when network segmentation and traffic visibility matter.
Empfohlen
Compact Network Access Products
The KSZ8893MBL supports compact network access products requiring three 10/100 Mbps service ports and an uplink rather than a high-port-count switching fabric. Its managed Layer 2 features allow service isolation, access control through rate limiting, and prioritization of selected traffic classes without a separate management controller. I2C and SPI host interfaces support configuration from a low-cost embedded processor. Because the device includes three PHYs, the product can reduce external Ethernet interface circuitry while retaining a managed topology. Board designers should still budget correctly for magnetics or fiber interfaces required by the selected Base-T, Base-TX, or Base-FX implementation.
Empfohlen
Factory Automation Communication Hubs
The KSZ8893MBL can serve as the Ethernet hub in factory automation communication equipment that connects sensors, controllers, and supervisory systems over 10/100 Mbps networks. VLAN support helps isolate traffic domains, rate limiting can restrain excessive traffic from individual endpoints, and QoS priority can improve the timeliness of control or diagnostic packets. The integrated PHYs reduce external interface count, while RMII, MII, and SNI options support different processor interfaces. MIB counters provide useful health and traffic statistics. The fine-pitch 100-pin LFBGA requires a capable PCB assembly process and disciplined separation of Ethernet, digital, power, and ground routing.
Empfohlen
Computing Module Connectivity
The KSZ8893MBL is suitable for computing modules that need a compact managed Ethernet front end for two external devices and one uplink. Its three integrated 10/100 PHYs provide a straightforward Layer 2 fabric, while VLAN and QoS functions allow the host software to organize traffic and prioritize selected services. The I2C and SPI management paths allow an embedded controller to initialize the switch and read counters, while RMII, MII, and SNI support different host-interface implementations. Its 100-pin LFBGA footprint can suit dense modules, although exposed-pad assembly, via-in-pad requirements, and thermal performance should be reviewed with the package drawing and assembly guidelines.
Empfohlen
Serialized Device Networking
The KSZ8893MBL can bridge multiple 10/100 Ethernet endpoints to a processor using RMII, MII, or SNI in equipment that serializes access to wired networks. Managed VLAN support can isolate endpoint traffic, QoS priority can favor real-time or control traffic, and rate limiting can protect shared links from burst traffic. I2C or SPI configuration allows software control, and MIB counters assist diagnosis in deployed equipment. This combination is useful in gateways and compact controllers that need more than an isolated Ethernet MAC. Exact PHY compliance, magnetics, termination, and isolation requirements must be taken from the complete manufacturer documentation.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für KSZ8893MBL – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | KSZ8893MBLI |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 100-pin LFBGA | 100-pin LFBGA |
| Product Type | 3-Port Layer 2 Managed Ethernet Switch | KSZ8893 family managed Ethernet switch |
| Number of Ethernet Ports | 3 ports | 3 ports |
| Ethernet Data Rate | 10/100 Mbps | 10/100 Mbps |
| Integrated PHYs | 3 integrated PHYs | 3 integrated PHYs |
| Host Interface | RMII/MII/SNI | RMII/MII/SNI |
| Management Interface | I2C and SPI | I2C and SPI |
| VLAN Support | Tag-based and port-based VLAN | Tag-based and port-based VLAN |
| Traffic Management | Rate limiting and QoS priority | Rate limiting and QoS priority |
| Management Statistics | MIB counters | MIB counters |
Wichtigste Unterscheidungsmerkmale
- Managed Layer 2 integration in three ports (vs. KSZ8893MBLI)
- Integrated PHYs reduce external interface count (vs. KSZ8893MBLI)
- Multiple host-interface choices (vs. KSZ8893MBLI)
- Traffic-management functions integrated into a low-port-count device (vs. KSZ8893MBLI)
Designhinweise
Treat the three Ethernet channels as controlled-impedance differential pairs and keep them away from switching nodes and high-current return paths. Follow the manufacturer reference layout for PHY-to-magnetics or PHY-to-fiber-interface placement. Because the verified source does not provide a complete ball map, the final PCB design should be checked against the official 100-pin LFBGA drawing before placement, breakout routing, and symbol creation.
Partition the board into Ethernet, CPU-interface, management-interface, and power-supply regions. Route RMII, MII, SNI, I2C, and SPI signals away from the Ethernet differential pairs, and provide uninterrupted reference planes beneath the device. The 100-pin LFBGA requires dense escape routing; confirm via geometry, exposed-pad treatment, assembly stencil, and via-in-pad policy with the PCB and assembly suppliers before release.
Do not treat the KSZ8893MBL, KSZ8893MBL-TR, and KSZ8893MBLI as identical ordering codes without checking their approved part data. The TR suffix denotes a packaging form, while the comparison evidence indicates that MBLI may differ in ordering or temperature-grade details. Verify operating limits, lifecycle status, moisture requirements, and production marking before selecting a replacement for an approved design.
Decouple each supply rail close to the relevant device pins and follow the values and sequencing requirements stated in the manufacturer data sheet. The verified search results do not provide the complete electrical table, so input-voltage limits, core and analog supply requirements, power-up order, and operating current must not be inferred. Confirm those values before designing the power tree or calculating regulator headroom.
Compliance-Informationen
The verified excerpts identify the manufacturer, product function, package, interfaces, and management features but do not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. These fields must be confirmed using the current Microchip product page or material-compliance documentation.
