Texas Instruments

LM2902KDBR - Quad 26V 1.2MHz Op Amp | Texas Instruments (Tape & Reel)

Teilenummer: LM2902KDBR ✓ Aktiv
26 V Vdss 2 nA Id 14-pin SSOP (DB) Package
MOQ: 1 |

LM2902KDBR Übersicht

Texas Instruments LM2902KDBR is a quad general-purpose operational amplifier with four amplifiers, a 26 V supply rating, 1.2 MHz gain-bandwidth performance, and improved 2 kV ESD protection. The device is offered in a 14-pin SSOP (DB) package for industrial, consumer, and automotive applications.

An operational amplifier is a voltage-amplifying circuit whose open-loop gain is controlled by negative feedback. Operational amplifiers belong to the analog IC hierarchy and support precision control, signal conditioning, buffering, current-to-voltage conversion, and closed-loop circuit functions. The LM2902K combines four general-purpose amplifiers in one package, reducing component count and simplifying multi-channel analog boards.

Key characteristics include four amplifier channels, a 26 V maximum supply rating, 1.2 MHz gain-bandwidth product, 2 kV improved ESD protection, and an operating temperature range from -40°C to 125°C. Typical input offset voltage is 3 mV, typical input offset current is 2 nA, and typical supply-current drain is 0.8 mA. The common-mode input range includes ground, allowing the amplifier to process signals close to the lower supply rail.

The LM2902K belongs to the improved LM2902B generation. According to the Texas Instruments product documentation, the LM324B and LM2902B families can replace earlier LM224, LM324, and LM2902 versions while preserving the familiar quad-amplifier architecture. The B generation emphasizes improved electrical characteristics and stronger ESD protection compared with legacy devices.

Typical applications include industrial control and instrumentation, sensor signal conditioning, transducer amplification, low-frequency active filters, audio preamplification, buffer stages, and general-purpose analog interfaces. The internal frequency compensation supports straightforward closed-loop operation in amplifier, comparator, and follower configurations when operating within the device's common-mode and output-voltage limits.

The most important layout consideration is stable decoupling. Place a supply-bypass capacitor close to the positive and ground pins, maintain short return paths, and avoid long traces around high-impedance inputs. Verify output-current, input common-mode range, output swing, and ambient-temperature limits for each channel because the four amplifiers share package power and thermal constraints.

This product page combines the LM2902KDBR operating characteristics, drop-in alternatives, application guidance, comparison parameters, and practical design notes in one engineering reference. Use the Texas Instruments LM2902K documentation as the controlling source for final electrical limits, pin assignments, ordering information, and PCB land patterns.

Drop-in-Alternativen für LM2902KDBR – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Varianten dieser Serie

Modelle derselben Serie, die drop-in-kompatibel sind mit LM2902KDBR (gleiche Bauform und Footprint) – abweichend in Package, Amplifier Type, Maximum Supply Voltage, Mounting Type, Operating Temperature Range.

Texas Instruments
Package: 14-SOIC
Mounting Type: Through-hole
Vergleichen mit LM2902KDBR →
Texas Instruments
Package: 14-pin SOIC
Amplifier Type: Quad general-purpose operational amplifier
Maximum Supply Voltage: 30 V
Vergleichen mit LM2902KDBR →
Texas Instruments
Package: 14-SOIC, 3.90 mm width
Amplifier Type: General purpose
Operating Temperature Range: -40 °C to +85 °C

LM2902BDB

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 14-pin SSOP (DB)
Improved LM2902B generation with the same 14-pin DB package; the 26 V class supply and 1.2 MHz class performance remain within the target operating class

📋 Referenzalternative (nicht im Katalog)

LM324BDB

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 14-pin SSOP (DB)
Same quad 14-pin DB architecture and 1.2 MHz class performance; verify the LM324B input-offset and supply limits against the LM2902KDBR requirements

📋 Referenzalternative (nicht im Katalog)

LM324KDB

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 14-pin SSOP (DB)
Quad amplifier in the same 14-pin DB footprint; the 1.2 MHz class remains comparable, while offset, supply, and ESD ratings require verification

📋 Referenzalternative (nicht im Katalog)

LM2902KDBG4

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 14-pin SSOP (DB)
Same LM2902KDBR electrical device and 14-pin DB package with the TI G4 processing designation; no 26 V or 1.2 MHz rating change

📋 Referenzalternative (nicht im Katalog)

LM2902KDG4

✅ Drop-In ⚠️ Spezifikationen ungeprüft
Texas Instruments
📦 14-pin SSOP (DB)
General-purpose operational amplifier · 4 channels · 26 V · 1.2 MHz · 2 kV · 14-SOIC · 3.90 mm (0.154 inch) · Through-hole

Preis auf Anfrage

Datenblatt ansehen →

LM2902KDBR Grenzwerte & elektrische Eigenschaften

Number of Amplifier Channels 4 channels
Amplifier Type General-purpose operational amplifier
Maximum Supply Voltage 26 V
Gain-Bandwidth Product 1.2 MHz
ESD Protection 2 kV improved ESD
Typical Input Offset Voltage 3 mV
Typical Input Offset Current 2 nA
Typical Supply-Current Drain 0.8 mA
Common-Mode Input Range Includes ground
Betriebstemperaturbereich -40°C to +125°C
Gehäuse 14-pin SSOP (DB)
Package Width 5.30 mm
Montageart Surface mount
Device Family LM2902K improved LM2902B generation
RoHS-Status Unknown
REACH Status Unknown
AEC-Q100 Qualification Unknown
Lead-Free Status Unknown

LM2902KDBR 5.30 mm Pinbelegungsleitfaden

Pinbelegung für LM2902KDBR (5.30 mm-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.

Pinbelegungsdiagramm für LM2902KDBR im 5.30 mm-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für LM2902KDBR.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

LM2902KDBR ist geeignet für 6 Anwendungs: Industrial Sensor Signal Conditioning, Transducer and Bridge Amplifier, Audio Preamplifier, Active Filters and Control Loops, Automotive Low-Speed Control Interface, General-Purpose Buffering and Amplification.

🏭

Industrial Sensor Signal Conditioning

The LM2902KDBR suits low-frequency industrial sensor conditioning because it combines four channels in one 14-pin SSOP and provides a common-mode input range that includes ground. A 1.2 MHz gain-bandwidth product is appropriate for scaling signals from resistive bridges, position sensors, and resistive transducers without demanding high-speed precision. Typical input offset voltage of 3 mV and input offset current of 2 nA help define the achievable accuracy, although the actual error budget must also include source impedance, resistor tolerance, and sensor excitation drift. Place the amplifier in the feedback path with the sensor return connected to the circuit ground, and verify that the output remains inside the amplifier's output-swing limits at every operating condition.

📡

Transducer and Bridge Amplifier

The LM2902KDBR can provide differential or single-ended gain for resistive bridge transducers in measurement systems. Its 1.2 MHz gain-bandwidth product supports practical closed-loop bandwidths well below the unity-gain frequency, while the input common-mode range extending to ground simplifies circuits that sense small voltage changes near the lower rail. The four-channel arrangement allows excitation buffers, differential amplification, active filtering, and output buffering to share one package. Designers should confirm the maximum input bias current, output-voltage swing, noise performance, and common-mode limits for their particular gain and bridge impedance. Stable feedback components and short, guarded input traces are important when the sensor output is small relative to offset and noise.

🎧

Audio Preamplifier

LM2902KDBR is appropriate for low-frequency audio preamplification, mixer, and buffering stages where a 1.2 MHz op-amp bandwidth is adequate. Four independent amplifiers in a single 14-pin SSOP can reduce board area for multi-channel consumer and industrial audio equipment. The amplifier's common-mode range includes ground, helping low-voltage audio signals remain within the usable input region, and its typical input offset voltage of 3 mV is a key factor when designing around low-level signals. Set the closed-loop gain with low-noise resistors and check output swing into the next stage. Headroom, distortion, frequency response, noise, and output-current capability remain design-dependent and should be confirmed from the manufacturer electrical tables.

⚙️

Active Filters and Control Loops

The LM2902KDBR can implement first- and second-order active filters, integrators, and low-frequency control-loop functions because each of its four amplifiers is internally frequency compensated. Its 1.2 MHz gain-bandwidth product gives sufficient loop bandwidth for many industrial monitoring and control applications, while the common-mode input range including ground simplifies signals centered around the lower rail. Component tolerances and the amplifier's actual gain-bandwidth, slew-rate, and noise behavior determine the achievable filter accuracy. Use stable resistor and capacitor arrangements, keep the feedback network compact, and avoid driving large capacitive loads without isolation. Four channels allow cascading stages or implementing several filters in parallel, reducing component count while preserving identical device characteristics.

🚗

Automotive Low-Speed Control Interface

The LM2902KDBR can support low-speed automotive control, actuator-interface, and diagnostic signal-conditioning functions when the individual operating limits are acceptable. The four-channel 14-pin SSOP provides a compact implementation for multiple low-frequency analog channels, and the -40°C to 125°C operating range covers widely varying vehicle temperatures. Improved 2 kV ESD protection adds useful robustness for exposed connections. Automotive qualification status, transient immunity, noise behavior, and the complete electrical limits must be checked before production release. Keep sensitive inputs away from engine-control harnesses and high-current switching paths, use short ground returns, and include protection networks that do not distort the intended signal bandwidth.

🔧

General-Purpose Buffering and Amplification

The LM2902KDBR is a practical choice for general-purpose buffering, gain adjustment, and impedance conversion in instruments, control boards, and consumer electronics. Four amplifiers in one package can replace several discrete devices while maintaining consistent behavior across channels. The 26 V supply rating accommodates higher-voltage analog systems, and the 1.2 MHz bandwidth is suitable for many low-frequency signals. The input common-mode range includes ground, which helps when buffering signals near the lower rail, while the typical 0.8 mA supply-current drain supports power-conscious designs when all four channels are active. Confirm output swing, load capability, stability with capacitive loads, thermal performance, and channel-to-channel behavior under the selected supply voltage and temperature.

Zusammenfassung der empfohlenen Produkte

LM2902BDB Quad operational amplifier for signal conditioning Verwendet in: Industrial Sensor Signal Conditioning, Audio Preamplifier, Automotive Low-Speed Control Interface LM324BDB General-purpose quad amplifier alternative Verwendet in: Industrial Sensor Signal Conditioning, Audio Preamplifier, Automotive Low-Speed Control Interface LM2902KDBG4 Same electrical configuration with processing designation Verwendet in: Transducer and Bridge Amplifier, Active Filters and Control Loops LM324KDB Quad general-purpose amplifier alternative Verwendet in: Transducer and Bridge Amplifier, Active Filters and Control Loops, General-Purpose Buffering and Amplification LM2902KDG4 Texas Instruments Verwendet in: General-Purpose Buffering and Amplification
What are the key specifications of LM2902KDBR that engineers should know?
The LM2902KDBR is a four-channel, general-purpose operational amplifier rated for operation from -40°C to 125°C. Its headline characteristics are a 26 V maximum supply rating, 1.2 MHz gain-bandwidth product, and improved 2 kV ESD protection. According to the Texas Instruments LM2902K product page, the device is packaged in a 14-pin SSOP with DB package designation. Typical input offset voltage is 3 mV, input offset current is 2 nA, and supply-current drain is 0.8 mA.
What is the operating voltage of LM2902KDBR?
The LM2902KDBR has a maximum supply rating of 26 V according to the Texas Instruments LM2902K product page. The broader LM2902B generation is described as a high-voltage operational-amplifier family with supply capability up to 36 V for B and BA versions. Do not treat 36 V as the LM2902KDBR limit; use the device-specific 26 V rating when checking absolute maximum conditions, supply transients, and automotive or industrial surge exposure.
Where can I download the LM2902KDBR datasheet PDF?
The official Texas Instruments LM2902K documentation is available through the manufacturer product page at https://www.ti.com/product/LM2902K. The LM2902KDBR ordering entry identifies the DB package as a 14-pin SSOP rated for -40°C to 125°C. Use the linked datasheet for the authoritative pin table, recommended operating conditions, electrical characteristics, and package drawings. Third-party HTML archives can assist with viewing, but the Texas Instruments document should control engineering release decisions.
Where can I find the LM2902KDBR pinout?
Use the pin-description table and package drawing in the Texas Instruments LM2902KDBR documentation to assign all 14 pins. The LM2902KDBR uses a 14-pin SSOP designated DB, with pin 1 identified by the package orientation marker and numbering proceeding counter-clockwise. The public product listing confirms the 14-pin package but does not reproduce the complete signal names, so the manufacturer pin table should be used before routing power, feedback, inputs, and outputs.
How does LM2902KDBR compare with LM2902KV?
LM2902KDBR and LM2902KV are closely related quad operational amplifiers, but their published maximum supply ratings differ. The Texas Instruments LM2902K page lists LM2902KDBR as a 26 V, 1.2 MHz quad amplifier, while the LM2902KV page describes a 30 V, 1.2 MHz version with improved 2 kV ESD protection and a -40°C to 125°C operating range. Package selection and pin compatibility must be checked independently because the ordering suffixes identify different package options.
When should I choose LM2902KDBR over LM2902KV?
Choose LM2902KDBR when the PCB uses the 14-pin DB SSOP footprint and the design requires the published 26 V maximum supply rating. Choose LM2902KV when its 30 V supply rating is appropriate for the application and the associated package is pin-compatible with the existing layout. Both devices provide four channels, 1.2 MHz gain-bandwidth performance, improved 2 kV ESD protection, and operation from -40°C to 125°C according to their Texas Instruments product pages.
What can replace LM2902KDBR?
The strongest replacements are four-channel operational amplifiers that use the same 14-pin DB SSOP footprint and preserve the LM2902K electrical class. Texas Instruments states that its LM324B and LM2902B generations can replace earlier LM224, LM324, and LM2902 versions, making qualified LM324BDB and LM2902BDB options worth evaluating. Before substitution, verify the exact pin map, supply rating, output swing, input common-mode range, operating temperature, and package dimensions against the original design.
Is LM2902KDBR the same as LM2902BDB?
LM2902KDBR and LM2902BDB belong to the same improved LM2902B family, but they are not necessarily identical ordering codes or ratings. Texas Instruments describes the LM324B and LM2902B devices as next-generation versions of the legacy LM224, LM324, and LM2902 products. For a direct substitution, confirm that the candidate has the same DB package dimensions, pin assignments, 14-pin pinout, supply limits, common-mode range, and required temperature grade.
What is the best Texas Instruments equivalent for LM2902KDBR?
LM2902BDB is the most direct Texas Instruments family candidate because it belongs to the improved LM2902B generation and is associated with the 14-pin DB package. LM324BDB may also be considered when its electrical limits satisfy the design. According to the Texas Instruments LM2902K documentation, the B generation can replace earlier LM2902 versions, but final approval still requires a package drawing and pin-by-pin comparison rather than relying on the family name alone.
Is LM2902KDBR suitable for sensor signal conditioning?
Yes, the LM2902KDBR is suitable for many low-frequency sensor signal-conditioning circuits. Its 1.2 MHz gain-bandwidth product, 3 mV typical input offset voltage, 2 nA typical input offset current, and common-mode input range that includes ground are useful for bridge, transducer, and buffered-sensing applications. Sensor designs must still verify input bias current, source impedance, output swing, noise, and common-mode limits over the complete temperature range.
What design considerations apply when using four LM2902KDBR amplifiers?
Treat the four amplifiers as one shared thermal and supply design. Estimated: at 12 V supply and 10 mA total load, the ideal supply-power draw is 120 mW before output swing, bias, and quiescent contributions. Place input and output paths away from switching nodes, connect decoupling capacitors close to the supply pins, and provide adequate copper for heat dissipation. Verify each channel's input range and output swing because one channel may saturate even while the other three operate normally.
Where can I buy LM2902KDBR and check its current price and lead time?
Use the Request a Quote form on this page to request the current LM2902KDBR unit price, stock position, minimum order quantity, and lead time. The component is identified as a Texas Instruments 14-pin SSOP, and a distributor listing records 22,422 pieces in stock with a unit price of 0.4374 as of 2026-11; however, that figure may change and should not be treated as a firm quotation. Packaging, date code, and quantity requirements should be confirmed when submitting the request.
Is LM2902KDBR in stock?
A distributor listing recorded 22,422 pieces of LM2902KDBR in stock and described the lead time as requiring confirmation, with an estimated delivery window of March 4 through March 9. Because inventory and delivery timing can change quickly, request a current quotation through the Request a Quote form on this page. Specify the required quantity, SSOP package, date-code preference, and target delivery location when asking for confirmation.
How much does LM2902KDBR cost?
The current transactional price for LM2902KDBR should be requested through the Request a Quote form on this page because market pricing and availability can change by quantity, date code, and packaging. A distributor listing recorded a unit price of 0.4374 as of 2026-11, while another listing stated that the component was available for immediate shipment. Request a binding quotation for the exact quantity and supply conditions before approving a production purchase.
What is the lead time for LM2902KDBR?
The current lead time for LM2902KDBR should be confirmed through the Request a Quote form on this page. One distributor listing described the lead time as to be confirmed and gave March 4 through March 9 as an estimated delivery window, while another result stated that the part ships today. Those statements may reflect different quantities, stock positions, or fulfillment models. Provide your required quantity and destination to obtain a delivery commitment for the order.

Technische Referenzdaten für LM2902KDBR – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose LM2902KDBR for a new 14-pin SSOP design that needs four general-purpose amplifiers, a 26 V maximum supply rating, 1.2 MHz bandwidth, operation from -40°C to 125°C, and improved 2 kV ESD protection. Choose LM2902KDBRG4 when the same electrical configuration is required with TI's G4 processing designation, and choose LM2902KDG4 when that ordering code meets your purchasing requirements without changing the core device class. LM2902BDB is the closest family-oriented substitute and should be checked for identical pin mapping and electrical limits. LM324BDB or LM324KDB may fit a compatible board, but they are different amplifier families and require explicit verification of offset voltage, bias current, supply limits, input common-mode range, and output swing. For any substitution, compare the manufacturer package drawing and pin table rather than relying on the package name alone.

Vergleich mit Alternativen

Parameter Dieses Produkt LM2902BDB LM324BDB LM324KDB LM2902KDBRG4 LM2902KDG4
Package 14-pin SSOP (DB) 14-pin SSOP (DB) 14-pin SSOP (DB) 14-pin SSOP (DB) 14-pin SSOP (DB) 14-pin SSOP (DB)
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Amplifier Channels 4 channels 4 channels 4 channels 4 channels 4 channels 4 channels
Special Features Improved LM2902B generation with 2 kV ESD protection Improved LM2902B generation Improved LM324B generation Legacy LM324 generation G4 processing designation G4 processing designation

Wichtigste Unterscheidungsmerkmale

  • Compact four-channel implementation with improved transient robustness (vs. LM324KDB)
  • Same improved LM2902B electrical family (vs. LM324BDB)
  • Identical ordering configuration available without electrical changes (vs. LM2902KDBRG4)

Designhinweise

Place the supply-bypass capacitor as close as possible to the positive supply and ground pins, with a short ground return to the device. Do not split the ground return between distant analog and power sections. Because the four amplifiers share package supply pins, estimate the total supply demand as four channel loads plus the typical 0.8 mA device drain, then verify the regulator's transient response and the package's allowable dissipation under worst-case conditions.

Route each noninverting and inverting input directly to its feedback and source components, avoiding parallel paths beneath or beside the amplifier. High-impedance inputs should be short and guarded against switching-node coupling. The internal compensation makes ordinary closed-loop layouts straightforward, but incorrect feedback connections can create oscillation or saturation. Verify every one of the 14 DB-package pins against the Texas Instruments pin table before releasing the PCB artwork.

Do not infer that the 36 V supply capability stated for other B or BA family versions applies to LM2902KDBR; its device listing specifies a 26 V maximum supply rating. Also confirm the input common-mode range and output swing at the chosen supply voltage. The common-mode range includes ground, but that does not mean every output can swing rail-to-rail or that inputs can safely reach the positive rail.

Evaluate the package temperature rise using the worst-case ambient temperature, supply voltage, output voltage, load current, and quiescent dissipation across all four channels. Estimated: power dissipation equals total output current multiplied by the output-to-ground voltage difference plus supply-voltage times total quiescent current. Use the manufacturer thermal parameters for the final junction-temperature calculation and provide copper area or thermal relief appropriate to the PCB and enclosure.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The LM2902KDBR is associated with industrial, consumer, and automotive applications, but the target's specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not identified in the manufacturer information.

Ähnliche Suchanfragen

LM2902KDBR LM2902KDBR datasheet LM2902KDBR datasheet pdf LM2902KDBR pinout LM2902KDBR equivalent LM2902KDBR replacement LM2902KDBR cross reference Texas Instruments LM2902KDBR LM2902KDBR 14 pin SSOP LM2902KDBR 26V 1.2MHz LM2902KDBR sensor amplifier LM2902KDBR vs LM2902KV LM2902KDBR price LM2902KDBR stock LM2902KDBR application circuit

Verwandte Bauteile & Begriffe

Texas Instruments LM2902KDBR LM2902K LM2902BDB LM324BDB LM324KDB LM2902KDBRG4 LM2902KDG4 LM2902KV Operational amplifier Quad operational amplifier General-purpose amplifier Analog integrated circuit General-purpose amplification Signal conditioning Active filter Power supply rejection Common-mode input voltage Input offset voltage Gain-bandwidth product ESD protection 14-pin SSOP DB package Surface-mount package Industrial control Automotive electronics
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen