LM358AP - Dual 30V 700kHz Op Amp | Texas Instruments
Teilenummer: LM358AP ✓ AktivLM358AP Übersicht
An operational amplifier, or op amp, is an analog integrated circuit that amplifies the voltage difference between its two inputs while using negative feedback to perform a defined gain function. The LM358 belongs to the dual operational amplifier, voltage-feedback amplifier, analog IC, and semiconductor hierarchy. Its two internally compensated channels make it suitable for sensor interfaces, transducer amplifiers, buffer stages, and general-purpose analog control circuits without requiring a separate single amplifier package.
The principal performance figures are a 700 kHz gain-bandwidth product, 0.3 V/µs slew rate, and approximately 2 mV input offset voltage. These characteristics make the LM358AP suitable for low-to-moderate frequency precision analog circuits. Its dual configuration provides channel-to-channel integration, while the wide 3 V to 30 V supply range allows operation from a single low-voltage rail or from split supplies. The device is available in an 8-pin PDIP package for through-hole PCB assembly.
Each channel uses a differential input stage, voltage-gain stage, and output stage, with internal compensation providing stable operation without an external compensation capacitor. Although the device is commonly associated with single-supply operation, its common-mode input range does not extend all the way to the positive supply rail. Designers should therefore verify the signal excursion against the common-mode limits before using the amplifier directly at the top of a low-voltage supply.
Typical uses include low-current sensor conditioning, buffered control inputs, audio preamplifier stages, active filtering, and general-purpose instrumentation. In a sensor interface, the LM358AP can amplify a small transducer signal while its dual channels support a second stage such as an inverter, buffer, or active filter. The 700 kHz bandwidth provides ample margin for slow sensor signals and low-frequency control loops.
PCB layout should keep input traces short, place bypass capacitance near the supply pin, and route output returns independently from sensitive input paths. Although the PDIP package is through-hole and easy to prototype, its lead pitch requires adequate clearance from adjacent components. Input and output nodes should also be kept apart to reduce parasitic feedback and oscillation risk.
This product page combines the LM358AP electrical characteristics, package details, application guidance, compatible replacements, and practical PCB considerations in a format that helps engineers evaluate the device before committing a through-hole design to production.
Drop-in-Alternativen für LM358AP – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit LM358AP (gleiche Bauform und Footprint) – abweichend in Input Offset Voltage, Operating Temperature Range, Package, Gain-Bandwidth Product, Mounting Type.
LM2904P3
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →LM258AP
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →LM358AP
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →LM358DT
✅ Drop-In✗ Nicht auf Lager
$0.0509 / Stück
Datenblatt ansehen →LM358DT
✅ Drop-In✗ Nicht auf Lager
$0.0509 / Stück
Datenblatt ansehen →LM358AP Grenzwerte & elektrische Eigenschaften
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Amplifier Channels | 2 channels |
| Maximum Supply Voltage | 30 V |
| Operating Supply Voltage Range | 3 V to 30 V |
| Split-Supply Input Voltage Range | -15 V to +15 V |
| Gain-Bandwidth Product | 700 kHz |
| Slew Rate | 0.3 V/µs |
| Input Offset Voltage | 2 mV |
| Betriebstemperaturbereich | 0°C to 70°C |
| Package Type | PDIP-8, through-hole |
| Anzahl der Pins | 8 pins |
| Montageart | Through-hole |
| Tube Quantity | 50 units per tube |
| RoHS-Status | Compliant |
| Lebenszyklusstatus | Active |
LM358AP pdip-8, through-hole Pinbelegungsleitfaden
Pinbelegung für LM358AP (pdip-8, through-hole-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.
Keine detaillierten Pinbelegungsdaten verfügbar für LM358AP.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
LM358AP ist geeignet für 6 Anwendungs: Sensor Signal Conditioning, Industrial Control Inputs, Audio Preamplification, Active Filtering and Buffering, Power Supply Feedback Conditioning, Test and Measurement Front Ends.
Sensor Signal Conditioning
The LM358AP suits low-frequency sensor interfaces because its 700 kHz gain-bandwidth product and 0.3 V/µs slew rate provide useful response margin beyond the bandwidth of many resistive sensors. A typical circuit uses one channel to amplify the sensor voltage and the second channel for buffering or active filtering. The 3 V to 30 V supply range supports both low-voltage portable instrumentation and higher-voltage industrial controls, but the input common-mode range must remain within the manufacturer limits. Ceramic bypass capacitance should be placed close to pin 8, with the supply return connected cleanly to pin 4.
Empfohlen
Industrial Control Inputs
LM358AP can condition low-level control or feedback signals in industrial control equipment while operating from a supply chosen within its 3 V to 30 V range. The two independent channels allow one amplifier to buffer a command input while the other amplifies a feedback voltage. Its 700 kHz bandwidth is appropriate for slow process-control loops rather than high-bandwidth servo systems. In a control board, keep the two channels electrically separated where possible, place the bypass capacitor near the supply pin, and avoid routing feedback from the output pins directly alongside input traces.
Empfohlen
Audio Preamplification
The LM358AP can provide a basic audio preamplifier stage for microphone-level or line-level signals when the operating bandwidth and noise requirements are modest. Its 0.3 V/µs slew rate allows full-scale output changes at frequencies below the 700 kHz gain-bandwidth limit, while the dual package can implement gain and filtering in separate channels. The amplifier must operate with adequate input and output common-mode headroom on a single 5 V supply. Decoupling and grounded input returns are important because audio preamplifiers can expose input-bias-current noise and power-supply ripple.
Empfohlen
Active Filtering and Buffering
LM358AP is practical for first-order or low-order active filters and for buffering sources with high output impedance. The dual amplifier provides separate active-filter stages without requiring two packages, and the 700 kHz bandwidth leaves useful range above typical audio, instrumentation, and industrial-control frequencies. Component tolerances directly influence the filter response, so use stable resistors and capacitors and simulate the final topology before fabrication. Place feedback components close to the relevant channel and maintain a direct ground return to minimize common-impedance coupling.
Empfohlen
Power Supply Feedback Conditioning
LM358AP can amplify a scaled power-supply feedback voltage for comparison against a reference in noncritical monitoring and control designs. Its wide 30 V maximum supply and approximately 2 mV offset make it useful for low-level feedback signals, although offset and drift should be checked against the required measurement accuracy. The second channel can monitor another rail or provide an inverter. Because the device is a linear amplifier rather than a switching regulator, it should sit outside high-current power paths and use separate input filtering to reject switching ripple.
Empfohlen
Test and Measurement Front Ends
The LM358AP can form a basic input buffer or gain stage for laboratory and industrial measurement equipment operating below the amplifier's 700 kHz bandwidth. Its dual-channel configuration supports an input buffer followed by gain, inversion, or offset adjustment. For precision measurements, verify input bias current, input offset voltage, and drift against the measurement specification because the general-purpose architecture is not automatically suitable for the highest-resolution instruments. Use short, guarded input traces, a quiet ground plane, and local supply bypassing to minimize measurement error.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für LM358AP – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | LM2904P3 | LM258AP | LM358AP | LM358 | LM358 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | STMicroelectronics | 3PEAK | SGMC |
| Package | PDIP-8 | PDIP-8 | PDIP-8 | PDIP-8 | PDIP-8 | PDIP-8 |
| Amplifier Configuration | Dual operational amplifier | Dual operational amplifier | Dual general-purpose operational amplifier | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier |
| Number of Pins | 8 pins | 8 pins | 8 pins | 8 pins | 8 pins | 8 pins |
Wichtigste Unterscheidungsmerkmale
- Wide operating supply range in a dual amplifier (vs. LM2904P3)
- Defined commercial-temperature operating range (vs. LM258AP)
- Established Texas Instruments dual op-amp configuration (vs. LM358 from 3PEAK)
Designhinweise
Place the supply bypass capacitor immediately between pin 8 and pin 4, with the ground connection returned directly to the device ground. Keep both input traces short and route them away from the output traces and supply-capacitor ground path. In a PDIP-8 layout, maintain adequate clearance between the 0.1-inch lead pitch and adjacent components, while confirming that the analog signal board does not share high-current switching paths.
Do not assume that the input common-mode range reaches the positive supply rail. The LM358AP supports single-supply operation, but the usable input range remains limited, particularly on a 3 V or 5 V rail. Verify the minimum and maximum signal levels at both amplifier inputs under load, and include adequate output headroom for the selected gain and waveform.
Use negative feedback to define the closed-loop gain and avoid unusually high closed-loop gain because the 700 kHz gain-bandwidth product leaves less stability margin as gain rises. Keep feedback components close to the relevant channel, use low-value resistors where practical to reduce parasitic capacitance effects, and probe the output with a short ground lead to distinguish circuit instability from measurement artifacts.
Estimated: with a 12 V supply, a 5 V output, and a 1 mA load, the LM358AP dissipation is approximately 7 mW using P = (VIN - VOUT) × IOUT. The estimate excludes internal ground-current and output-stage contributions, so use the manufacturer power-dissipation limits for final thermal analysis. The small result indicates that normal low-load operation generally needs no dedicated heatsink.
Compliance-Informationen
The manufacturer product information identifies LM358AP as active and RoHS compliant. No separate REACH, lead-free, halogen-free, or conflict-minerals declaration was identified in the cited product records.
