LT1352CS8 - Dual 3MHz 250mA Operational Amplifier | Analog Devices
Teilenummer: LT1352CS8 ✗ AbgekündigtLT1352CS8 Übersicht
An operational amplifier is a voltage-controlled analog amplifier that uses external feedback to set gain and is intended for amplification, buffering, filtering, and signal conditioning. The LT1352CS8 belongs to the broader operational-amplifier hierarchy, which includes voltage-feedback amplifiers, instrumentation amplifiers, comparators, and other precision or high-speed analog IC families. Its dual-channel configuration provides two amplifiers in one package, reducing component count and simplifying layout where two independent channels are required.
The verified product information identifies the LT1352/LT1353 family as a very-low-power, high-speed operational-amplifier family with lower supply current and higher slew rate than comparable-bandwidth devices. The LT1352CS8 specifically provides two amplifier channels, a 3 MHz bandwidth rating, a 200 V/µs slew-rate rating, and a 250 mA drive rating. These characteristics make it useful in applications requiring faster edge rates or greater output-current capability than a general-purpose low-power amplifier.
The matched high-impedance input architecture is useful when the source impedance is relatively high or when input bias current can disturb the signal node. The high slew rate can improve large-signal response in instrumentation, waveform-generation, and feedback-control circuits, while the 3 MHz bandwidth supports moderate-frequency signal amplification. The 8-pin SOIC package is a conventional surface-mount format suitable for PCB assembly and repair workflows.
Typical applications include sensor-signal conditioning, audio and communications buffers, active filters, instrumentation interfaces, data-conversion support circuits, and general analog control loops. When selecting it for a new design, verify the supply-voltage limits, input common-mode range, output swing, noise, offset, and stability requirements against the manufacturer datasheet. The published family description supports the use of the LT1352CS8 for low-power, high-speed dual-channel analog signal processing, but detailed operating limits should be confirmed before finalizing a circuit.
This page combines the verified LT1352CS8 product details with practical selection guidance, replacement criteria, and design notes. The key engineering trade-off is the balance between low power consumption, high speed, and output drive in an 8-pin dual operational-amplifier package.
Drop-in-Alternativen für LT1352CS8 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
LT1352IS8
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LT1352CS8 Grenzwerte & elektrische Eigenschaften
| Amplifier Type | Voltage Feedback Operational Amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 3 MHz |
| Slew Rate | 200 V/µs |
| Output Current | 250 mA |
| Gehäuse | 8-pin SOIC |
| Montageart | Surface Mount |
| RoHS-Status | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
| Lead-Free Status | unknown |
| Halogen-Free Status | unknown |
| Conflict-Minerals Status | unknown |
LT1352CS8 8-pin soic Pinbelegungsleitfaden
Pinbelegung für LT1352CS8 (8-pin soic-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.
Keine detaillierten Pinbelegungsdaten verfügbar für LT1352CS8.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
LT1352CS8 ist geeignet für 6 Anwendungs: Sensor Signal Conditioning, Instrumentation and Data Acquisition, Active Filtering and Buffering, Communications Signal Conditioning, Audio and Low-Distortion Drive, General Analog Control Loops.
Sensor Signal Conditioning
The LT1352CS8 fits sensor front ends that need two buffered channels in a compact 8-pin SOIC. Its matched high-impedance inputs help reduce loading of high-impedance sensors, while the 3 MHz bandwidth accommodates signals above the range of basic low-speed amplifiers. The 200 V/µs slew rate also supports rapid settling when the sensor output changes quickly. Use one channel for amplification and the other for filtering, buffering, or an auxiliary instrumentation function. Verify the input common-mode range and output swing against the sensor excitation and signal levels before finalizing the interface.
Empfohlen
Instrumentation and Data Acquisition
The LT1352CS8 can provide dual-channel amplification in instrumentation systems where moderate bandwidth and fast transient response are required. The 3 MHz gain-bandwidth product supports higher-frequency measurement nodes than a general-purpose low-speed operational amplifier, and the 200 V/µs slew rate helps preserve large-signal behavior. Its dual-channel SOIC format simplifies routing where two related analog signals must be conditioned in the same area. Check the complete electrical limits, especially supply range, common-mode range, offset, and noise, against the acquisition system requirements.
Empfohlen
Active Filtering and Buffering
The LT1352CS8 is suitable for active filter and buffer stages that need two amplifiers without using separate packages. Its 3 MHz bandwidth provides useful signal-path headroom for low- and moderate-frequency filters, while the 200 V/µs slew rate helps maintain low distortion for larger output transitions. The matched high-impedance inputs are valuable when the filter follows a high-impedance source. Confirm stability with the selected feedback network, capacitor values, and capacitive load because those characteristics are not available in the product summary.
Empfohlen
Communications Signal Conditioning
The LT1352CS8 can be used in communications and interface circuits where two analog channels require modest bandwidth, controlled impedance, and relatively fast slew performance. The 3 MHz bandwidth is appropriate for many baseband conditioning paths, and the 200 V/µs slew rate improves response to abrupt signal transitions. Its dual-channel 8-pin SOIC footprint reduces board area compared with two separate single amplifiers. For high-speed RF or communications chains, verify the required gain-bandwidth product, noise, output drive, and supply requirements rather than assuming the LT1352CS8 is sufficient.
Empfohlen
Audio and Low-Distortion Drive
The LT1352CS8 can serve as a dual audio-buffer or line-stage amplifier when the design requires faster signal handling than a low-power general-purpose op amp. The 200 V/µs slew rate supports larger signal transitions, while the 3 MHz bandwidth provides more signal-path range than a low-frequency amplifier. The 250 mA output-current rating is useful when driving a load that is more demanding than a purely small-signal measurement node. Confirm output swing, load stability, and distortion specifications from the manufacturer datasheet before using it in a precision audio path.
Empfohlen
General Analog Control Loops
The LT1352CS8 is appropriate for general-purpose analog control and feedback circuits where low power, dual channels, and faster response are all useful. The 3 MHz bandwidth supports loop dynamics beyond a slow comparator or precision reference amplifier, while the 200 V/µs slew rate can improve response during large control excursions. A dual package allows one amplifier to perform control and the other to provide sensing or monitoring. Validate loop stability, output saturation behavior, and supply sequencing in the final system.
Empfohlen
Technische Referenzdaten für LT1352CS8 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | LT1352IS8 |
|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC |
| Brand | Analog Devices | Analog Devices |
| Number of Channels | 2 | 2 |
| Amplifier Type | Voltage Feedback Operational Amplifier | LT1352 family voltage-feedback operational amplifier |
| Input Architecture | Matched high-impedance inputs | Matched high-impedance inputs |
Wichtigste Unterscheidungsmerkmale
- Dual high-speed channels in one 8-pin SOIC (vs. LT1352IS8)
- 200 V/µs slew rate for large-signal response (vs. LT1352IS8)
- 3 MHz bandwidth with high-impedance inputs (vs. LT1352IS8)
Designhinweise
Place the LT1352CS8 close to the sources and loads of both amplifier channels. Route each input and output with short traces, keep the ground-return path continuous, and place input and output decoupling according to the manufacturer datasheet. Because the device is a dual amplifier in an 8-pin SOIC, separating the two channels where possible can reduce crosstalk and make the layout easier to debug.
Do not assume that the 3 MHz bandwidth, 200 V/µs slew rate, and 250 mA drive rating guarantee operation at every supply voltage or output amplitude. Check the input common-mode range, output swing, supply limits, load stability, and thermal limits in the LT1352 datasheet. In particular, verify that the selected feedback network remains stable with the output load and cable capacitance.
For high-impedance sources, keep input-node leakage and PCB contamination under control and use a nearby ground reference. The LT1352 family uses matched high-impedance inputs, but the practical signal node is still affected by board leakage, probe capacitance, and feedback-component tolerances. Use short, guarded input routes and suitable resistor values when processing high-source-impedance sensors.
Compliance-Informationen
The verified records identify the manufacturer and product family but do not state the requested compliance statuses. The LT1352 is an analog operational amplifier, so AEC-Q100 qualification is marked not_applicable for this product classification.