Analog Devices

LT6301IFE - Dual 500mA xDSL Line Driver | Analog Devices

Teilenummer: LT6301IFE ✓ Aktiv
Externally adjustable with resistor Vdss 500 mA minimum per channel Id 28-lead TSSOP with exposed pad Package
MOQ: 1 |

LT6301IFE Übersicht

The Analog Devices LT6301IFE is a dual 500 mA differential xDSL line driver in a 28-lead TSSOP package with an exposed pad. It is designed to drive two telephone-line connections from one package and meets the drive requirements associated with full-rate downstream ADSL line interfaces. The device provides two high-current differential outputs, low distortion performance, gain-of-ten stability, and externally adjustable supply current for power optimization.

A differential xDSL line driver is an interface IC that converts a low-voltage signal into a balanced, high-current output suitable for transmission over twisted-pair wiring. Its role within the signal chain is upstream of the isolation transformer or line termination network, where it must preserve signal integrity while delivering enough current into the intended load. The LT6301IFE belongs to the broader operational-amplifier, interface-driver, line-driver, and telecommunications-IC hierarchy.

The LT6301IFE drives two lines from one package and provides a minimum output current of 500 mA per channel. Its gain-of-ten stability makes it suitable for fixed-gain line-driver configurations, while compensation can be added for operation at lower closed-loop gains. Extended output swing allows designers to use lower supply rails, reducing system power when the required output amplitude permits it. Supply current is controlled by an external resistor, allowing optimization between drive capability and dissipation.

Internally, the LT6301 architecture combines balanced, high-impedance inputs with high-output-current capability. The manufacturer datasheet describes a design in which a direct DC path exists between the outputs of the two amplifiers. Consequently, input bias imbalance during startup or a fault condition can create differential output DC voltage. Application layouts and bias networks should therefore be evaluated carefully rather than treating the two channels as completely independent isolated drivers.

Typical uses include full-rate and downstream ADSL line-driver circuits, central-office line-card interfaces, telecommunications test equipment, and other balanced line-driver designs requiring two 500 mA outputs. The device is particularly relevant where a compact surface-mount implementation must combine two high-current differential channels with adjustable power dissipation.

The most important design consideration is heat management. A 500 mA output capability can produce substantial dissipation when the supply-to-output voltage difference and output swing are high. Use the exposed pad as a thermal path, connect it to a suitable ground plane as directed by the manufacturer, and calculate worst-case channel dissipation across load, supply, and temperature conditions.

This product page consolidates the manufacturer specifications, package information, application guidance, and strictly drop-in-oriented alternatives into an engineering-focused view. It also highlights the thermal and DC-balance considerations that matter when adapting the LT6301IFE to a real xDSL line interface.

Drop-in-Alternativen für LT6301IFE – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

LT6301HFE

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 28-lead TSSOP with exposed pad
Same-family LT6301 architecture and 500 mA-class dual output; temperature-grade details require confirmation before substitution

📋 Referenzalternative (nicht im Katalog)

LT6301EFE

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 28-lead TSSOP with exposed pad
Same-family dual 500 mA xDSL line-driver architecture; operating-temperature and ordering-code differences require confirmation

📋 Referenzalternative (nicht im Katalog)

LT6301IFE Technische Daten

Product Type Dual differential xDSL line driver
Number of Channels 2 channels
Output Current Capability 500 mA minimum per channel
Minimum Output Current 500 mA per channel
Gain Stability Gain of 10
Signal Type Differential xDSL line signal
Line Count 2 lines from one package
Supply Current Control Externally adjustable with resistor
Input Impedance High impedance, balanced inputs
Output Swing Extended output swing
Gehäuse 28-lead TSSOP with exposed pad
Pin-Anzahl 28 pins
Montageart Surface mount
Production Status Production

LT6301IFE 28-lead tssop with exposed pad Pinbelegungsleitfaden

Pinbelegung für LT6301IFE (28-lead tssop with exposed pad-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.

Pinbelegungsdiagramm für LT6301IFE im 28-lead tssop with exposed pad-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für LT6301IFE.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

LT6301IFE ist geeignet für 6 Anwendungs: Full-Rate Downstream ADSL Line Driver, Central-Office ADSL Line Card, Balanced Telecommunications Test Equipment, Twisted-Pair Transmitter Interface, High-Current Differential Output Stage, Telecom Line-Card Signal Conditioning.

🌐

Full-Rate Downstream ADSL Line Driver

The LT6301IFE fits a full-rate downstream ADSL interface because it provides two differential channels with 500 mA minimum output current per channel from one 28-lead TSSOP-EP package. Each amplifier can drive the external line network through the system transformer and termination arrangement. Gain-of-ten stability simplifies the closed-loop design when that gain is acceptable, while external supply-current adjustment allows the designer to balance output capability against dissipation. Confirm the final supply voltage, load, transformer ratio, compensation network, and worst-case thermal conditions before releasing the line interface.

🏭

Central-Office ADSL Line Card

A central-office ADSL line card can use the LT6301IFE to consolidate two high-current differential transmit channels into a compact surface-mount footprint. The dual 500 mA-class output capability is appropriate for driving line-side networks through isolation and termination components, while the exposed pad supports heat flow into the PCB ground structure. Design the supply network for the dynamic load presented by two active channels, provide adequate bypass capacitance, and verify temperature-grade requirements against the line-card environment. The regulator, transformer, and protection components should be selected as a complete line-interface subsystem.

🔧

Balanced Telecommunications Test Equipment

The LT6301IFE can generate differential test signals for balanced telecommunications lines because its two channels provide at least 500 mA of output current and gain-of-ten stability. The externally adjustable supply current is useful in laboratory platforms where output swing and dissipation must be tailored to the injected signal level. Place the device close to the line interface and use controlled impedance paths to prevent reflections. Validate output amplitude, bandwidth, common-mode behavior, and thermal rise with the intended transformer or termination before using the circuit as a production test source.

📡

Twisted-Pair Transmitter Interface

A twisted-pair transmitter interface benefits from the LT6301IFE's balanced outputs, high-impedance inputs, and extended output swing. Two channels can serve separate line pairs, or the device can support a dual-ended transmit arrangement when the surrounding circuit topology requires it. Because the manufacturer datasheet identifies a direct DC path between the amplifier outputs, biasing and startup behavior must be examined carefully to prevent unintended differential DC voltage. Add suitable protection, maintain transformer or termination compliance, and account for the line-coupling network when setting gain and output amplitude.

⚡

High-Current Differential Output Stage

For a high-current differential output stage requiring a fixed closed-loop gain near 10, the LT6301IFE offers two amplifier channels with 500 mA minimum output current. Its high-impedance balanced inputs simplify biasing around a line-driver network, while the externally controlled supply current can be tuned according to the required output swing and channel dissipation. The trade-off is that linear high-current drive converts supply-to-output voltage difference into heat. Use the exposed pad as a thermal path and estimate each channel's dissipation before fixing the operating point or increasing system voltage.

🖥️

Telecom Line-Card Signal Conditioning

The LT6301IFE is suitable for the transmit side of a telecom line card when two low-distortion differential channels are needed in one package. Gain-of-ten stability provides a straightforward starting point for closed-loop line-driver compensation, and the balanced high-impedance inputs help isolate the driver from preceding signal-conditioning stages. The circuit must still account for the internal DC relationship between the amplifier outputs, especially during turn-on or a fault. Combine careful input-bias design with exposed-pad thermal routing and normal line-network protection to achieve reliable operation.

What is the LT6301IFE?
The LT6301IFE is a dual 500 mA differential xDSL line driver from Analog Devices in a 28-lead TSSOP package with an exposed pad. According to the Analog Devices datasheet, it drives two lines from one package and supports full-rate downstream ADSL line-driver requirements. Each channel provides at least 500 mA of output current, uses balanced high-impedance inputs, and is gain-of-ten stable for straightforward closed-loop line-driver design.
What are the key specifications of LT6301IFE that engineers should know?
The key LT6301IFE specifications are two differential channels, 500 mA minimum output current per channel, gain-of-ten stability, externally adjustable supply current, high-impedance balanced inputs, and extended output swing. The Analog Devices datasheet also identifies the device as a power-enhanced 28-lead TSSOP line driver. These characteristics make it suitable for dual-line ADSL interfaces, although the exact supply range and thermal limits must be taken from the device datasheet.
What is the output current of LT6301IFE?
The LT6301IFE provides 500 mA minimum output current per channel, allowing one device to drive two xDSL lines. The Analog Devices product page describes the LT6301 as a dual 500 mA differential xDSL line driver. Actual usable current depends on supply voltage, output voltage, load, thermal conditions, and the selected external supply-current-setting resistor, so the circuit should be checked against the worst-case operating envelope.
Where can I download the LT6301IFE datasheet PDF?
The LT6301IFE datasheet PDF is available from Analog Devices at https://www.analog.com/media/en/technical-documentation/data-sheets/6301fs.pdf. The document contains the electrical characteristics, application information, line-driver circuit, supply-current-setting guidance, and package details. Use the manufacturer document for the authoritative pin description, absolute maximum ratings, thermal information, and recommended operating conditions.
Where can I find the LT6301IFE pinout?
The LT6301IFE pinout is shown in the pin-description and package-drawing sections of the Analog Devices LT6301 datasheet. The component uses a 28-lead TSSOP with an exposed pad, so the exposed thermal pad must not be confused with a conventional numbered signal pin. Assign PCB tracks from the manufacturer pin table rather than inferring connections from the physical drawing alone.
What applications use the LT6301IFE?
The LT6301IFE is used in dual differential xDSL line-driver circuits, particularly full-rate downstream ADSL line interfaces. Its two 500 mA channels allow a compact design to drive two telephone lines from one package. Other appropriate uses include central-office line cards, balanced telecommunications interfaces, and test equipment, provided the supply, load, compensation, isolation-transformer, and thermal requirements are matched to the datasheet.
What is the difference between LT6301IFE and LT6301HFE?
The LT6301IFE and LT6301HFE are variants in the LT6301 family, but the verified product information available for this page does not establish the complete temperature-grade or ordering-code differences. Before treating HFE as a replacement, compare its package, operating-temperature range, absolute maximum ratings, and lifecycle status against the LT6301IFE. A replacement decision also requires confirmation that the output-current and supply settings remain equivalent.
LT6301IFE vs LT6301HFE - which is better for an ADSL line card?
Choose the LT6301IFE when its documented temperature grade and electrical ratings match the ADSL line-card environment; choose the LT6301HFE when a wider temperature range or other qualified family rating is required and the manufacturer confirms identical pin compatibility. Both devices should provide the same basic dual-channel, 500 mA-class xDSL-driver architecture. Confirm the exact ordering variant, supply limits, exposed-pad connection, and production status before finalizing the BOM.
When should I choose LT6301IFE over another xDSL line driver?
Choose the LT6301IFE when the design needs two differential channels, at least 500 mA of output current per channel, a gain-of-ten-stable architecture, and adjustable supply current in a 28-lead TSSOP-EP package. It is a strong fit for full-rate downstream ADSL line interfaces requiring compact dual-line drive. Select another qualified driver if the design needs different voltage limits, temperature coverage, isolation, bandwidth, or output-current behavior.
Is LT6301IFE suitable for central-office telecom equipment?
The LT6301IFE can be suitable for central-office line-card and telecom interface equipment because it provides two 500 mA-class differential outputs in one package and supports external supply-current adjustment. Suitability still depends on the exact temperature grade, reliability program, regulatory requirements, and available operating ratings. The Analog Devices datasheet should be checked for absolute maximum ratings and environmental limits before release to production.
What can replace LT6301IFE?
A valid replacement for the LT6301IFE must use the same 28-lead TSSOP-EP land pattern, remain pin-to-pin compatible, support at least 500 mA output current per channel, and meet the required supply and temperature limits. The verified cross-reference results identify the LT6301 family but do not substantiate a different-manufacturer drop-in device. Treat unverified functional equivalents as redesign candidates rather than drop-in replacements.
What is the best drop-in replacement for LT6301IFE?
The best-supported drop-in candidate is another properly ordered LT6301 family variant with the same 28-lead TSSOP-EP pinout and equivalent electrical ratings. LT6301HFE may be evaluated as a same-family candidate, but its temperature-grade differences must be confirmed before substitution. No cross-brand part is presented as a drop-in replacement because the verified sources do not establish same-package, pin-compatible operation and equivalent 500 mA performance.
Where can I buy LT6301IFE online?
Use the Request a Quote form on this page to request LT6301IFE availability, lot traceability, and current commercial terms. The form is the appropriate channel for checking exact suffix, condition, and lead time without relying on a stale listing. Because the target suffix includes integrated-circuit ordering and packaging information, provide the complete LT6301IFE MPN and required quantity in the request.
What is the price of LT6301IFE?
The current commercial price for LT6301IFE is best obtained through the Request a Quote form on this page. Pricing can vary with quantity, date of order, condition, traceability, and the exact ordering suffix. The structured pricing evidence for this exact MPN does not contain qualifying quantity-break prices, so no static price figure is shown on this page.
What is the lead time for LT6301IFE?
The current lead time for LT6301IFE should be requested through the Request a Quote form on this page. Lead time can depend on factory inventory, order quantity, and the exact LT6301IFE ordering suffix. Submit the required quantity and target delivery date with the request so procurement can confirm the most accurate schedule for the current market.
How should the LT6301IFE be handled for thermal reliability?
Design the LT6301IFE around its exposed thermal pad and worst-case dissipation from both 500 mA channels. Estimated: for each channel, dissipation is approximately (VIN - VOUT) multiplied by output current; two active channels double the total before accounting for bias and other circuit losses. Use the resulting value with the manufacturer thermal data to size copper, check junction temperature, and determine whether additional airflow or heat spreading is required.

Technische Referenzdaten für LT6301IFE – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the LT6301IFE for a dual xDSL transmit path requiring two differential outputs, at least 500 mA per channel, balanced high-impedance inputs, and a gain-of-ten-stable topology in a 28-lead TSSOP-EP package. LT6301HFE is a same-family option to evaluate when its temperature grade and other ordering details fit the equipment more closely. LT6301EFE is another same-family candidate whose temperature and ordering-code differences must be reconciled with the exact design requirements. Neither candidate should be released without confirming the manufacturer ordering table, absolute maximum ratings, and pin configuration. A different-manufacturer device should be selected only after its land pattern, drive current, supply range, bandwidth, compensation requirements, and thermal limits have been verified as drop-in compatible.

Vergleich mit Alternativen

Parameter Dieses Produkt LT6301HFE LT6301EFE
Brand Analog Devices Analog Devices Analog Devices
Package 28-lead TSSOP with exposed pad 28-lead TSSOP with exposed pad 28-lead TSSOP with exposed pad
Product Type Dual differential xDSL line driver Dual differential xDSL line driver Dual differential xDSL line driver
Number of Channels 2 channels 2 channels 2 channels
Minimum Output Current 500 mA per channel 500 mA per channel 500 mA per channel
Gain Stability Gain of 10 Gain of 10 Gain of 10
Supply Current Control Externally adjustable with resistor Externally adjustable with resistor Externally adjustable with resistor
Input Characteristics Balanced, high-impedance inputs Balanced, high-impedance inputs Balanced, high-impedance inputs
Output Capability Extended output swing Extended output swing Extended output swing

Wichtigste Unterscheidungsmerkmale

  • Two high-current differential channels in one package (vs. LT6301HFE)
  • Externally adjustable supply current (vs. LT6301EFE)
  • Gain-of-ten-stable line-driver architecture (vs. LT6301HFE)

Designhinweise

Estimate dissipation for both channels before layout. Estimated: each channel dissipates approximately (VIN - VOUT) multiplied by output current, so two channels can dissipate twice the per-channel value before bias losses. Compare the total with the exposed-pad thermal path and maximum junction temperature. Use substantial uninterrupted PCB copper around the pad, follow the manufacturer land pattern, and add airflow or copper spreading if the calculated rise is excessive.

Place the input, feedback, compensation, and supply-setting components close to their associated LT6301IFE pins to minimize parasitic feedback and supply noise. Keep high-current output paths compact and pair them according to the differential line-network requirements. Route the exposed pad directly into a low-impedance thermal and ground structure as specified in the package drawing. Verify that return currents do not share narrow paths with sensitive input-bias nodes.

Do not overlook the DC relationship between the two amplifier outputs described in the Analog Devices datasheet. An imbalance in the noninverting-input bias potentials, including startup or fault conditions, can create differential output DC voltage. Review both bias networks, startup sequencing, fault behavior, and the external line termination. Also avoid assuming that the 500 mA rating applies without checking the associated supply voltage, output swing, load, and thermal limits.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

Compliance attributes are unknown because the cited product information does not state them explicitly. Automotive qualification is not established by the xDSL application and must not be inferred.

Daten verifiziert am: 2026-11-09 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

LT6301IFE datasheet LT6301IFE specifications LT6301IFE pinout LT6301IFE datasheet pdf LT6301IFE equivalent LT6301IFE replacement LT6301IFE drop-in substitute LT6301IFE xDSL line driver LT6301IFE 500mA output current LT6301IFE TSSOP-28 package Analog Devices LT6301IFE LT6301IFE price LT6301IFE stock LT6301IFE vs LT6301HFE

Verwandte Bauteile & Begriffe

Analog Devices LT6301IFE LT6301HFE LT6301EFE dual xDSL line driver differential line driver xDSL ADSL operational amplifier interface IC telecommunications IC 500 mA output current gain-of-ten stability power supply rejection common-mode voltage TSSOP-28 exposed pad surface mount line transformer twisted-pair analog signal RoHS REACH
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen