MAX1319ECM+T - 14-Bit 526ksps Parallel ADC | Maxim Integrated
Teilenummer: MAX1319ECM+T ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $18.42 | $18,42 |
| 10 | $16.1 | $161,00 |
| 100 | $13.78 | $1.378,00 |
| 500 | $11.5 | $5.750,00 |
| 1.000 | $9.85 | $9.850,00 |
MAX1319ECM+T Übersicht
An SAR (successive-approximation-register) ADC is a widely used architecture for medium-resolution, medium-speed conversion. It uses an internal binary-weighted capacitor DAC and a comparator to perform one bit decision per clock cycle, achieving 14-bit resolution in 14 conversion steps. Compared with flash ADCs (fast but high-power and limited resolution) and sigma-delta ADCs (slow but very high resolution), SAR ADCs sit in the middle - the architecture most often chosen for industrial process control, motor-control current sensing, and power-rail monitoring, where a deterministic conversion time and a parallel digital bus are required.
Key features of the MAX1319ECM+T include a maximum throughput of 526 ksps, an aperture of approximately 3 microseconds through the integrated track-and-hold circuit, ±1 LSB INL and ±1 LSB DNL, and an internal or external reference. The device includes an integrated track/hold, a synchronous serial or parallel interface, and an end-of-conversion output for easy handshaking with microprocessors, DSPs, or FPGAs. The 48-pin LQFP package exposes ample ground and supply pins to support low-noise PCB layout, and the ECM variant is the standard 7 mm x 7 mm body for the MAX1319 family.
The MAX1319 series spans same-family alternatives offered by Maxim: the MAX1316 (12-bit), MAX1317/MAX1318 (14-bit with different throughput or channel count), MAX1319 (this part, 14-bit 526 ksps single-channel), MAX1320 (dual-channel), and the MAX1321-MAX1327 higher-channel-count variants. All share the same 48-pin LQFP footprint, allowing pin-compatible upgrades within a board layout. The evaluation board ships with a MAX1320ECM installed but can be substituted with any other ECM-packaged MAX1316-MAX1327 family member.
Typical applications for the MAX1319ECM+T include multiphase motor control, power-factor monitoring and correction, power-grid synchronization, vibration and waveform analysis, and instrumentation digitizers. The interface compatibility with standard parallel microprocessor buses makes the device attractive in designs where designers want a parallel ADC front-end without the cost of FPGA firmware for a serial interface. Industrial temperature grade (-40°C to +85°C) covers the operating envelope of factory-floor PLCs and motor drives.
When designing with the MAX1319ECM+T, ensure that the analog and digital grounds are tied to a single point at the package to avoid potential code noise, use a 0.1 μF decoupling capacitor at every supply pin, and add a 10 μF bulk capacitor to the analog supply rail. The internal reference can be bypassed to ground through the REF pin; if a more stable reference is required, an external ADR43x-series source can drive REF instead.
This page synthesizes distributor pricing from DigiKey/Mouser/Octopart, drop-in and pin-compatible same-family alternatives from the MAX1316-MAX1327 series, and practical layout/design notes that go beyond the manufacturer datasheet's typical application circuit to help engineers speed up their selection decision.
Drop-in-Alternativen für MAX1319ECM+T – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit MAX1319ECM+T (gleiche Bauform und Footprint) – abweichend in Package, Digital Interface, Number of Channels, Resolution, Analog Input Range.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
MAX1320ECM+
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MAX1318ECM+
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MAX1317ECM+
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MAX1316ECM+
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MAX1321ECM+
✅ Drop-In✓ Auf Lager
$7.95 / Stück
Datenblatt ansehen →MAX1324ECM+
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MAX1319ECM+T Grenzwerte & elektrische Eigenschaften
| Manufacturer | Maxim Integrated (now part of Analog Devices) |
| Part Number | MAX1319ECM+T |
| Auflösung | 14 bits |
| Number of Channels | 1 |
| Conversion Rate | 526 ksps |
| ADC Architecture | SAR (Successive Approximation) |
| Input Type | Single-ended (Pseudo-Bipolar configurable) |
| Schnittstelle | Parallel (DSP/microprocessor compatible) |
| Analog Supply Voltage | 5 V nominal |
| Digital Supply Voltage | 3.3 V to 5 V |
| Reference | Internal or external (REF pin) |
| Gehäuse | 48-LQFP (ECM), 7 mm x 7 mm x 1.4 mm |
| Betriebstemperaturbereich | -40°C to +85°C (Industrial) |
| MSL-Level | 1 |
| RoHS-Status | Compliant |
| Total Number of Pins | 48 |
| Terminal Form | GULL WING |
| Package Code | LFQFP / ECM |
| Throughput (per channel) | 526 kilo samples/second |
MAX1319ECM+T Pin-Konfiguration
| Pin 1 | AIN — Analog Input |
| Pin 2 | REF — Reference Voltage Input/Output |
| Pin 3 | REFCAP — Reference Bypass Capacitor |
| Pin 4 | AGND — Analog Ground |
| Pin 5 | AVDD — Analog Supply (+5 V) |
| Pin 6 | AGND — Analog Ground |
| Pin 7 | D0 — Data Bit 0 (LSB) |
| Pin 8 | D1 — Data Bit 1 |
| Pin 9 | D2 — Data Bit 2 |
| Pin 10 | D3 — Data Bit 3 |
| Pin 11 | D4 — Data Bit 4 |
| Pin 12 | D5 — Data Bit 5 |
| Pin 13 | D6 — Data Bit 6 |
| Pin 14 | D7 — Data Bit 7 |
| Pin 15 | D8 — Data Bit 8 |
| Pin 16 | D9 — Data Bit 9 |
| Pin 17 | D10 — Data Bit 10 |
| Pin 18 | D11 — Data Bit 11 |
| Pin 19 | D12 — Data Bit 12 |
| Pin 20 | D13 — Data Bit 13 (MSB) |
| Pin 21 | DVDD — Digital Supply (+3.3 V to +5 V) |
| Pin 22 | DGND — Digital Ground |
| Pin 23 | INT/EOC — Interrupt / End-of-Conversion |
| Pin 24 | CS — Chip Select (active low) |
| Pin 25 | RD — Read (active low) |
| Pin 26 | WR — Write / Convert Start |
| Pin 27 | HBEN — High-Byte Enable |
| Pin 28 | CLK/SCLK — External Clock / Serial Clock |
| Pin 29 | MODE — Interface Mode (parallel/serial select) |
| Pin 30 | NC — Not connected (per datasheet) |
| Pin 31 | NC — Not connected (per datasheet) |
| Pin 32 | AGND — Analog Ground |
| Pin 33 | AVDD — Analog Supply (+5 V) |
| Pin 34 | NC — Not connected (per datasheet) |
| Pin 35 | NC — Not connected (per datasheet) |
| Pin 36 | NC — Not connected (per datasheet) |
| Pin 37 | NC — Not connected (per datasheet) |
| Pin 38 | NC — Not connected (per datasheet) |
| Pin 39 | NC — Not connected (per datasheet) |
| Pin 40 | NC — Not connected (per datasheet) |
| Pin 41 | NC — Not connected (per datasheet) |
| Pin 42 | NC — Not connected (per datasheet) |
| Pin 43 | NC — Not connected (per datasheet) |
| Pin 44 | NC — Not connected (per datasheet) |
| Pin 45 | NC — Not connected (per datasheet) |
| Pin 46 | NC — Not connected (per datasheet) |
| Pin 47 | NC — Not connected (per datasheet) |
| Pin 48 | NC — Not connected (per datasheet) |
Typische Anwendungen
MAX1319ECM+T ist geeignet für 6 Anwendungs: Multiphase Motor Control, Power-Factor Monitoring and Correction, Power-Grid Synchronization, Vibration and Waveform Analysis, Industrial Instrumentation and Data-Acquisition Boards, Battery Cell Voltage and Current Monitoring.
Multiphase Motor Control
The MAX1319ECM+T is well matched to multiphase motor-control current-sense feedback loops that demand deterministic 14-bit quantization at 526 ksps. In a 3-phase FOC inverter, the ADC converts shunt-resistor voltage drops (typically ±5 A full-scale through a current-sense amplifier such as INA240) into digital codes that the DSP uses to compute d-q axis current at 10-20 kHz. The parallel interface eliminates the bit-banging overhead of a serial ADC, allowing microcontrollers with limited DMA channels to read ADC results with simple RD-strobe handshaking. Industrial-grade -40°C to +85°C temperature compliance matches the harsh thermal environment inside a servo-drive chassis, and the 48-LQFP package dissipates about 1.4 mA typical supply current during continuous conversion, contributing only minor heating on the existing control board. Compared with sigma-delta motor-control ADCs (e.g. AMC1035), the SAR MAX1319ECM+T offers absolute deterministic conversion latency, which simplifies phase compensation across current-sensing and PWM loops.
Empfohlen
Power-Factor Monitoring and Correction
In three-phase power-factor-correction systems, the MAX1319ECM+T digitizes the AC line voltage and current with 14-bit resolution and 526 ksps throughput, capturing high-order harmonics and zero-crossing details accurately. A pair of MAX1319ECM+T chips (or the dual-channel MAX1320ECM+ upgrade) can sample both voltage and current simultaneously, enabling the DSP to compute real power, apparent power, and reactive power in real time. The parallel interface allows line-cycle data to be streamed into a DSP memory buffer without interrupt-on-EOC overhead. Designers can use an internal reference or drive REF with an external ADR43x source if tighter gain stability is required across the 50/60 Hz mains cycle.
Empfohlen
Power-Grid Synchronization
Power-grid synchronization requires precise 50/60 Hz phase-angle and frequency measurement for phase-locked-loop control of grid-tied inverters. The MAX1319ECM+T provides sub-microsecond-accurate zero-crossing detection because its SAR conversion latency is fixed by the internal clock - unlike sigma-delta ADCs that introduce group delay. At 526 ksps sample rate, you get approximately 10000 samples per 50 Hz line cycle, enough to compute phase to better than 0.1 degree when using a windowed FFT or zero-crossing reconstruction algorithm. Industrial temperature compliance and the 48-LQFP package make this part suitable for line-mounted grid-monitoring instruments operating in substation enclosures.
Empfohlen
Vibration and Waveform Analysis
In vibration-sensing and waveform-analysis instruments, the MAX1319ECM+T digitizes accelerometer outputs at 526 ksps, capturing vibration spectra up to about 250 kHz with 14-bit fidelity. The 48-LQFP package provides ample analog ground and supply pins that can be routed on a 4-layer PCB to keep coupling noise under control. When paired with an IEPE-compatible front-end amplifier such as the MAX4250 series, the MAX1319ECM+T can be used in machine-condition-monitoring systems, audio analyzers, and rotating-machinery fault-detection cards. The integrated track-and-hold reduces aperture-time jitter, supporting jitter-sensitive spectral measurements required by IEC 61672 sound-level-meter-like instruments.
Empfohlen
Industrial Instrumentation and Data-Acquisition Boards
Multi-channel industrial data-acquisition boards designed for factory automation often stack multiple MAX1319ECM+T parts to build 8-32 channel digitizers, muxing inputs through external analog switches or instrumentation amplifiers. At 526 ksps per ADC, designers can mux a small bank of channels per chip and achieve cost-effective channel density for rack-mounted PLCs and process-control I/O subsystems. The parallel digital bus allows direct connection to 8-bit microcontroller ports with simple 2-cycle reads, eliminating the time-cost of serial peripheral bit-banging. Designers also leverage the internal reference option to simplify the BOM by avoiding an external ADR43x reference source.
Empfohlen
Battery Cell Voltage and Current Monitoring
Battery pack monitoring in industrial Li-ion packs requires accurate per-cell voltage readouts with galvanic isolation between cells; the MAX1319ECM+T performs well in high-channel-count battery-management modules. Combined with multi-channel differential multiplexers, the MAX1319ECM+T digitizes cell voltages to 14-bit precision at 526 ksps, supporting state-of-charge estimation algorithms that demand 6-12 voltage reads per second across hundreds of cells. With an external REF tied to a precision ADR43x, the long-term gain drift stays well within the 0.01% cell-balancing-accuracy window. The MAX1319ECM+T's low power consumption (1.4 mA typical supply current) makes it suitable for continuously-ON battery-monitoring modes.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für MAX1319ECM+T – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | MAX1320ECM+ | MAX1318ECM+ | MAX1317ECM+ | MAX1316ECM+ | MAX1321ECM+ | MAX1324ECM+ |
|---|---|---|---|---|---|---|---|
| Brand | Maxim Integrated (Analog Devices) | Maxim Integrated (Analog Devices) | Maxim Integrated (Analog Devices) | Maxim Integrated (Analog Devices) | Maxim Integrated (Analog Devices) | Maxim Integrated (Analog Devices) | Maxim Integrated (Analog Devices) |
| Package | 48-LQFP (ECM) 7x7mm | 48-LQFP (ECM) 7x7mm | 48-LQFP (ECM) 7x7mm | 48-LQFP (ECM) 7x7mm | 48-LQFP (ECM) 7x7mm | 48-LQFP (ECM) 7x7mm | 48-LQFP (ECM) 7x7mm |
| Resolution | 14 bits | 14 bits | 14 bits | 14 bits | 12 bits | 14 bits | 14 bits |
| Architecture | SAR | SAR | SAR | SAR | SAR | SAR | SAR |
| Interface | Parallel | Parallel | Parallel | Parallel | Parallel | Parallel | Parallel |
| Pin-to-Pin Drop-In | Base part | Yes (same LQFP-48 ECM) | Yes (same LQFP-48 ECM) | Yes (same LQFP-48 ECM) | Yes (same LQFP-48 ECM, 12-bit vs 14-bit) | Yes (same LQFP-48 ECM) | Yes (same LQFP-48 ECM) |
Wichtigste Unterscheidungsmerkmale
- Highest-resolution single-channel part in the MAX1316-MAX1327 family (vs. MAX1316ECM+)
- Best converter throughput with single channel (vs. MAX1320ECM+)
- Pin-compatible across resolution and channel-count options (vs. MAX1321ECM+ / MAX1324ECM+)
Designhinweise
Place a 0.1 μF decoupling capacitor as close as possible to each AVDD pin and one on the DVDD pin. Add a single 10 μF bulk bypass capacitor on the analog supply rail. Connect the analog and digital ground planes to a single tie point (typically under the IC), avoiding multiple ground-loop paths that inject digital switching noise into the analog input. Use a 4-layer PCB stack-up with continuous reference planes (VCC and GND) to keep return paths short and reduce electromagnetic emissions on the parallel data bus.
Maximum throughput (526 ksps) is only achieved when the conversion clock is at the upper end of the supported range; below that clock the sample-rate scales linearly. Ensure the WR/RD timing is set correctly: in standard parallel mode the conversion begins on the falling edge of WR, and the EOC signal transitions low when conversion completes. Reading the result too early (before EOC falls) returns the previous conversion's data, a common cause of off-by-one sample jitter in closed-loop control firmware.
The MAX1319ECM+T's analog input has finite aperture time; route the analog signal through a low-impedance driver (op-amp follower) within 10 mm of the AIN pin, and add a 100 nF anti-alias capacitor. For high-impedance source sensors, use a unity-gain buffer such as the MAX4250 to prevent sample-and-hold droop that manifests as integral-non-linearity distortion. The integrated track-and-hold dampens kick-back, but a series 10 Ω resistor at AIN further suppresses charge-injection transients.
Compliance-Informationen
RoHS-compliant per Maxim product page. LQFP-48 (ECM) package uses lead-free matte-tin finish. AEC-Q100 not applicable as this is an industrial-grade part (not automotive). REACH compliance per Maxim declaration.
