Microchip Technology

MCP634-E/SL - 24MHz Quad Rail-to-Rail Op Amp | Microchip

Teilenummer: MCP634-E/SL ✓ Aktiv
10 nV/√Hz typical at 1 MHz Vdss 70 mA typical Id 14-SOIC, 0.154 in (3.90 mm) body width Package
MOQ: 1 |

MCP634-E/SL Übersicht

The Microchip Technology MCP634-E/SL is a four-circuit general-purpose operational amplifier with a 24 MHz gain-bandwidth product, 10 V/µs slew rate, and rail-to-rail output operation in a 14-pin SOIC package. Its typical input-voltage noise is 10 nV/√Hz at 1 MHz, and its typical output short-circuit current is 70 mA.

An operational amplifier, commonly called an op amp, is a high-gain analog building block used to amplify, buffer, filter, compare, and drive signals. Within the semiconductor hierarchy, the MCP634-E/SL belongs to the operational amplifier family, which is part of amplifier ICs and analog signal-chain processing. Four independent amplifiers in one package reduce component count and can simplify board layout for multi-channel designs.

The MCP63x family is optimized for high gain-bandwidth product and high output short-circuit current. In the MCP634-E/SL, the 24 MHz gain-bandwidth product supports wider closed-loop bandwidth than lower-bandwidth general-purpose amplifiers. The 10 V/µs typical slew rate improves large-signal response, while rail-to-rail output operation allows the output to approach the supply rails more closely than a conventional fixed-output-stage design.

The amplifier combines 24 MHz typical gain-bandwidth product with 10 nV/√Hz typical input noise at 1 MHz and a 70 mA typical output short-circuit current. These characteristics make it suitable for sensor conditioning, active filtering, data acquisition, audio paths, and general-purpose analog signal processing where modest-to-high bandwidth is required. The exact input and output voltage limits, common-mode range, and supply-current conditions should be confirmed in the manufacturer datasheet for the intended design.

Typical uses include buffering sensor outputs, implementing active low-pass and band-pass filters, amplifying low-level analog signals, providing channel multiplexing support in instrumentation systems, and driving moderate loads. Because the MCP634-E/SL contains four amplifiers in one package, synchronized or repetitive analog channels can use one device instead of four separate single-amplifier packages.

PCB design should account for the 14-pin SOIC footprint, provide a continuous ground path, and decouple each supply rail close to the device. Avoid long high-impedance traces around sensitive input nodes because the 10 nV/√Hz noise specification does not eliminate errors caused by PCB leakage, grounding problems, or common-mode voltage exceeding the amplifier's operating range.

This product page combines the manufacturer product information, distributor identification, verified electrical characteristics, package details, and a practical assessment of drop-in family alternatives. It also adds application guidance and design considerations that help engineers evaluate the MCP634-E/SL beyond a basic parameter listing.

Drop-in-Alternativen für MCP634-E/SL – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

MCP634T-E/SL

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 14-SOIC
Temperature-grade ordering variant; gain-bandwidth product remains 24 MHz typical and package remains 14-SOIC, with the operating-temperature rating requiring confirmation

📋 Referenzalternative (nicht im Katalog)

MCP634-E/TA

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 14-SOIC
Tube-packaged 14-SOIC family ordering option with the same MCP634 architecture; electrical grade and ordering-code details require confirmation

📋 Referenzalternative (nicht im Katalog)

MCP634-E/SL Grenzwerte & elektrische Eigenschaften

Amplifier Type General Purpose
Number of Circuits 4 circuits
Gain-Bandwidth Product 24 MHz typical
Slew Rate 10 V/µs typical
Input Voltage Noise Density 10 nV/√Hz typical at 1 MHz
Output Short-Circuit Current 70 mA typical
Output Topology Rail-to-Rail Output
Gehäuse 14-SOIC, 0.154 in (3.90 mm) body width
Montageart Surface mount
Packaging Tube

MCP634-E/SL 14-soic, 0.154 in (3.90 mm) body width Pinbelegungsleitfaden

Pinbelegung für MCP634-E/SL (14-soic, 0.154 in (3.90 mm) body width-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.

Pinbelegungsdiagramm für MCP634-E/SL im 14-soic, 0.154 in (3.90 mm) body width-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für MCP634-E/SL.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

MCP634-E/SL ist geeignet für 6 Anwendungs: Sensor Signal Conditioning, Active Audio Filtering, Data Acquisition Front End, Industrial Control Signal Buffering, Low-Level Analog Signal Amplification, General-Purpose Analog Interface.

🧩

Sensor Signal Conditioning

The MCP634-E/SL is well suited to conditioning outputs from sensors whose bandwidth requirements exceed that of a slow precision amplifier. Its 24 MHz typical gain-bandwidth product provides useful closed-loop bandwidth in moderately high-gain configurations, while the 10 nV/√Hz typical input noise at 1 MHz helps preserve low-level signal integrity. Place the amplifier close to the sensor interface, provide local supply bypassing, and keep the input route short. Confirm that the sensor output remains inside the device's input common-mode range. The 14-SOIC package also allows four amplifier channels to support related sensing or gain stages without using four separate packages.

🎧

Active Audio Filtering

The MCP634-E/SL can implement active filters for audio and other bandwidth-limited analog signals. Its 24 MHz typical gain-bandwidth product provides more closed-loop bandwidth than a low-frequency general-purpose amplifier, while the 10 V/µs typical slew rate helps preserve large-signal dynamics. The four amplifiers can form two independent filter channels or a more complex state-variable network. Select resistor and capacitor values using the closed-loop gain and stability guidance in the manufacturer datasheet. Verify output swing under the worst-case load, because rail-to-rail output capability does not guarantee zero distortion at every supply voltage.

📊

Data Acquisition Front End

For instrumentation and data-acquisition systems, the MCP634-E/SL can amplify a differential or single-ended sensor signal before conversion or digitization. The 24 MHz typical gain-bandwidth product supports sampling systems requiring more bandwidth than a precision-only amplifier, and four circuits allow channel multiplexing, gain stages, or buffer functions to be consolidated. Keep sensitive inputs away from digital return currents, use a solid ground reference, and bypass the supply pins locally. The input common-mode and output swing conditions must remain within the manufacturer limits. Four amplifiers in one 14-SOIC also reduce package count, although thermal performance should be checked under simultaneous maximum-load operation.

🏭

Industrial Control Signal Buffering

The MCP634-E/SL can buffer and amplify control, feedback, and monitoring signals in industrial electronics where compactness and moderate bandwidth are useful. Its 24 MHz typical gain-bandwidth product allows closed-loop operation above the bandwidth of many general-purpose low-speed amplifiers, while the 70 mA typical output short-circuit current provides useful transient drive capability. Use each amplifier with a defined reference for bipolar signals and maintain a common ground strategy across analog and control domains. Confirm industrial temperature requirements, output loading, and supply tolerance before release. The 14-SOIC package simplifies routing in dense control boards while providing four amplifier channels.

📈

Low-Level Analog Signal Amplification

The MCP634-E/SL is appropriate for small analog signals that require more bandwidth or slew rate than a conventional precision op amp. Its 10 nV/√Hz typical input noise at 1 MHz and 24 MHz typical gain-bandwidth product provide a practical balance between noise and bandwidth. Use a low-noise reference and suitable feedback resistors, and avoid excessive capacitance directly on the input because it can alter phase margin and stability. Place the amplifier near the source to minimize induced noise and leakage. Before committing to a noise-sensitive path, compare the complete signal-chain noise budget, including reference, resistor, and ADC contributions.

🔧

General-Purpose Analog Interface

The MCP634-E/SL works as a general-purpose interface element for buffering, gain adjustment, impedance conversion, and signal conditioning in mixed-signal equipment. Its 10 V/µs typical slew rate supports faster signal transitions than low-bandwidth amplifiers, and the four-channel 14-SOIC configuration simplifies allocation across a board. Decouple the supply connection at the package and connect the ground pins to a low-impedance plane. Keep feedback loops compact and use guard techniques or guarding strategies where leakage from a high-impedance source could affect accuracy. Confirm the actual output-current demand, because the 70 mA short-circuit current value describes typical short-circuit behavior rather than continuous-load capability.

Zusammenfassung der empfohlenen Produkte

MCP634-E/SL Microchip Technology Verwendet in: Sensor Signal Conditioning, Active Audio Filtering, Data Acquisition Front End, Industrial Control Signal Buffering, Low-Level Analog Signal Amplification, General-Purpose Analog Interface MCP634T-E/SL Temperature-grade family option Verwendet in: Sensor Signal Conditioning, Data Acquisition Front End, Low-Level Analog Signal Amplification MCP634-E/TA Same-family tube-packaged option Verwendet in: Active Audio Filtering, Industrial Control Signal Buffering, General-Purpose Analog Interface
What is the MCP634-E/SL?
The MCP634-E/SL is a four-circuit general-purpose operational amplifier from Microchip Technology with a 24 MHz typical gain-bandwidth product, 10 V/µs typical slew rate, and rail-to-rail output operation. According to the Microchip MCP634 product page, the MCP63x family is optimized for high gain-bandwidth product and high output short-circuit current. The device is packaged in a 14-SOIC and can be used for amplification, filtering, buffering, comparison, and multiple-channel analog signal processing.
What are the key specifications of MCP634-E/SL that engineers should know?
The MCP634-E/SL combines four general-purpose amplifier circuits, 24 MHz typical gain-bandwidth product, 10 V/µs typical slew rate, 10 nV/√Hz typical input noise at 1 MHz, and 70 mA typical output short-circuit current. It uses a 14-SOIC package and provides rail-to-rail output operation. According to the manufacturer product page, these amplifiers are optimized for high gain-bandwidth product and high output short-circuit current, making them practical for wider-bandwidth analog signal chains.
What is the gain-bandwidth product of MCP634-E/SL?
The MCP634-E/SL has a gain-bandwidth product of 24 MHz typical. According to the manufacturer product page, the MCP63x family is optimized for high gain-bandwidth product and high output short-circuit current. In practical filter and amplifier designs, the 24 MHz figure indicates the useful closed-loop bandwidth will depend on the selected noise gain, while the 10 V/µs typical slew rate determines large-signal response.
Does MCP634-E/SL have rail-to-rail output?
Yes, the MCP634-E/SL provides rail-to-rail output operation. The manufacturer identifies this feature in the MCP63x family description, while the device listing describes the MCP634 as a general-purpose rail-to-rail amplifier. Rail-to-rail output is useful when the signal must approach the supply limits more closely, but output-headroom and load-current limitations must still be checked in the manufacturer datasheet.
Where can I download the MCP634-E/SL datasheet PDF?
The official MCP634 product page is available at Microchip's website and is the appropriate starting point for the MCP634-E/SL datasheet and family documentation. Use the manufacturer datasheet for the complete electrical characteristic table, pin description, recommended operating conditions, package drawings, and ordering information. The MCP634-E/SL is the tube-packaged 14-SOIC orderable designation within the MCP634 family.
Where can I find the MCP634-E/SL pinout?
The MCP634-E/SL pin assignment is found in the pin-description table of the manufacturer datasheet for the MCP634 family. The device is a 14-pin SOIC containing four operational amplifiers. Use the datasheet's package drawing and pin-description table when assigning power, ground, input, output, and any chip-select or shutdown functions rather than relying on a generic 14-pin layout.
What can replace the MCP634-E/SL?
The closest confirmed family replacement is MCP634T-E/SL, which retains the MCP634 four-amplifier architecture and 14-SOIC footprint while representing a different temperature-grade ordering option. A broader cross-brand replacement should be selected only after verifying every pin, supply range, common-mode range, output swing, stability requirement, and noise specification. The MCP634T-E/SL is therefore a direct family option, not evidence that every 14-SOIC quad amplifier is interchangeable.
Is MCP634T-E/SL the same as MCP634-E/SL?
MCP634T-E/SL is a temperature-grade ordering variant of the MCP634 family rather than a different amplifier architecture. Both use the same four-circuit, 24 MHz-class MCP634 platform and 14-SOIC footprint. The design should still check the exact ordering table and operating-temperature limits before substitution. According to the manufacturer family information, the defining performance characteristics are high gain-bandwidth product and high output short-circuit current.
What is the best Microchip equivalent for MCP634-E/SL?
MCP634T-E/SL is the closest confirmed Microchip alternative because it preserves the MCP634 family architecture, four amplifier circuits, and 14-SOIC footprint. The primary distinction is the ordering temperature grade, so the required operating-temperature range must be checked before installation. No cross-brand equivalent is recommended without a manufacturer pinout and parametric comparison demonstrating true pin-to-pin compatibility.
When should I choose MCP634-E/SL over MCP634T-E/SL?
Choose MCP634-E/SL when its specified temperature range covers the operating environment and the tube-packaged 14-SOIC configuration matches the assembly plan. Choose MCP634T-E/SL when the broader temperature-grade designation is required by the product's operating conditions. Both retain the same four-channel amplifier architecture and package footprint, making the decision primarily an ordering-temperature and qualification requirement rather than a bandwidth choice.
Is MCP634-E/SL suitable for sensor and active-filter applications?
Yes, the MCP634-E/SL is suitable for many sensor-conditioning and active-filter applications. Its 24 MHz typical gain-bandwidth product supports closed-loop gains that need reasonable bandwidth, while 10 nV/√Hz typical input noise at 1 MHz is useful for low-level sensor signals. Confirm the sensor output range against the input common-mode limits and use the feedback network values from the manufacturer datasheet for stable filter designs.
How much thermal dissipation should I allow for MCP634-E/SL?
Thermal dissipation depends on the actual supply voltage, output voltage, output current, ambient temperature, and PCB copper area, so a fixed value cannot be assigned without those operating conditions. The MCP634-E/SL also has a 70 mA typical output short-circuit current, but this is not a continuous-output rating. Use the manufacturer power-dissipation limits and thermal information for the 14-SOIC package, and estimate total four-amplifier dissipation from the actual worst-case operating mode.
Where can I request a quote for MCP634-E/SL?
Use the Request a Quote form on this page to request MCP634-E/SL pricing, stock confirmation, and lead time for the tube-packaged 14-SOIC orderable designation. Current commercial terms should be confirmed at the time of quotation because market pricing and component availability can change. The Request a Quote workflow provides a direct way to obtain the exact quantity and manufacturing-plan information required for procurement.
What is the lead time for MCP634-E/SL?
The current lead time for MCP634-E/SL should be confirmed through the Request a Quote form on this page. Lead time can vary with order quantity, packaging requirements, and current inventory, so a generic delay would not be reliable for production planning. Include the required quantity, tube packaging, target delivery date, and any quality or traceability requirements with the quotation request.
Is MCP634-E/SL in stock?
Current MCP634-E/SL inventory should be confirmed through the Request a Quote form on this page before a purchase order is released. Marketplace listings may change independently, while assembly planning requires a firm allocation for the exact 14-SOIC orderable code and packaging configuration. Request the quantity and delivery schedule needed for your build or maintenance program.
Does MCP634-E/SL meet RoHS, REACH, or automotive qualification requirements?
RoHS, REACH, and AEC-Q100 status cannot be confirmed from the product characteristics alone and must be checked in the current manufacturer product page, declaration, or qualification documents for the exact orderable part. The MCP634-E/SL is identified as a general-purpose 14-SOIC amplifier, not as an automotive-qualified variant. Use the manufacturer compliance documentation before treating the device as suitable for a regulated or automotive program.

Technische Referenzdaten für MCP634-E/SL – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose MCP634-E/SL when the design needs four general-purpose amplifier channels, approximately 24 MHz gain-bandwidth product, 10 V/µs slew rate, and a compact 14-SOIC footprint. Its rail-to-rail output is useful for signal chains with limited supply headroom, provided the output swing remains acceptable under the intended load. MCP634T-E/SL is the preferred direct family option when the ordering-temperature grade must differ, while MCP634-E/TA provides another same-family 14-SOIC ordering option. These alternatives preserve the core amplifier architecture, but the exact temperature, supply, and qualification requirements must be checked before installation. Do not substitute a generic 14-SOIC quad amplifier solely by package count; input common-mode range, chip-select or shutdown pins, output behavior, noise, stability, and exposed temperature ratings must also match.

Vergleich mit Alternativen

Parameter Dieses Produkt MCP634T-E/SL MCP634-E/TA
Brand Microchip Technology Microchip Technology Microchip Technology
Package 14-SOIC 14-SOIC 14-SOIC
Number of Circuits 4 circuits 4 circuits 4 circuits
Amplifier Type General Purpose General Purpose General Purpose
Gain-Bandwidth Product 24 MHz typical 24 MHz typical 24 MHz typical
Slew Rate 10 V/µs typical 10 V/µs typical 10 V/µs typical
Input Voltage Noise Density 10 nV/√Hz typical at 1 MHz 10 nV/√Hz typical at 1 MHz 10 nV/√Hz typical at 1 MHz
Output Short-Circuit Current 70 mA typical 70 mA typical 70 mA typical
Output Topology Rail-to-Rail Output Rail-to-Rail Output Rail-to-Rail Output

Wichtigste Unterscheidungsmerkmale

  • Four active amplifier channels in one package (vs. MCP634T-E/SL)
  • No functional architecture change across the listed family alternatives (vs. MCP634-E/TA)
  • Balanced speed and input-noise characteristics (vs. MCP634T-E/SL)

Designhinweise

Place the device close to the protected signal source and route inputs away from switching nodes, inductors, and high-current return paths. Keep the feedback components adjacent to the relevant amplifier pins, and use a continuous ground reference rather than a narrow connection through analog and digital sections. The 10 nV/√Hz typical input-noise figure applies to the device itself; PCB leakage and interference can dominate the practical noise performance of a high-impedance source.

Place the supply bypass capacitor immediately beside the power pin and connect the ground return directly to the ground plane. Use a short, low-inductance supply path to preserve the benefit of the 24 MHz typical gain-bandwidth product and 10 V/µs typical slew rate. Verify the exact operating supply range, output-current limit, and output-swing behavior in the manufacturer datasheet before driving the amplifier near its limits.

Do not assume that a rail-to-rail output reaches either supply rail with zero error under every load. Check the output-voltage headroom at the intended frequency and load, and confirm that input common-mode voltage remains within the amplifier's operating range. Also distinguish the 70 mA typical short-circuit-current value from a continuous-load rating; sustained output current can be lower and depends on the device's thermal conditions.

Estimate dissipation for all four amplifiers under the worst simultaneous operating condition rather than evaluating only one channel. Because the 14-SOIC package has limited heat-dissipation area compared with larger packages, use the manufacturer's thermal information and provide adequate PCB copper. If all four channels operate continuously at high output current and elevated ambient temperature, recalculate junction temperature before approving the layout.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

Compliance and automotive-qualification status require confirmation from the current Microchip documentation for the exact orderable part.

Daten verifiziert am: 2026-11-10 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

MCP634-E/SL datasheet MCP634-E/SL pinout MCP634-E/SL datasheet pdf Microchip MCP634-E/SL MCP634-E/SL specifications MCP634-E/SL equivalent MCP634-E/SL replacement MCP634-E/SL drop-in substitute MCP634-E/SL vs MCP634T-E/SL MCP634 14-SOIC operational amplifier MCP634-E/SL 24MHz op amp MCP634-E/SL sensor amplifier MCP634-E/SL active filter MCP634-E/SL price MCP634-E/SL stock

Verwandte Bauteile & Begriffe

Microchip Technology MCP634-E/SL MCP634T-E/SL MCP634-E/TA MCP634 MCP63x family operational amplifier op amp general-purpose amplifier amplifier IC analog signal chain quad amplifier gain-bandwidth product slew rate input voltage noise density output short-circuit current rail-to-rail output active filter sensor signal conditioning data acquisition 14-SOIC SOIC package family surface-mount package tube packaging
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen