NXP Semiconductors

MKL27Z64VFM4 - 48MHz Cortex-M0+ USB MCU | NXP

Teilenummer: MKL27Z64VFM4 ✓ Aktiv
32-QFN (5 x 5 mm) Package 48 MHz Speed 64 KB (64K x 8) Memory
MOQ: 1 |

MKL27Z64VFM4 Übersicht

The NXP Semiconductors MKL27Z64VFM4 is an ultra-low-power 32-bit microcontroller with an Arm Cortex-M0+ core operating up to 48 MHz, 64 KB of embedded Flash memory, and a full-speed USB 2.0 device controller. It is packaged in a 32-QFN 5 x 5 mm surface-mount package for compact portable, USB-connected, and embedded products.

A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and I/O into one device. The MKL27Z64VFM4 belongs to the NXP Kinetis KL2 family, placing it within the hierarchy of 32-bit MCU, embedded controller, embedded processor, and semiconductor. Its ultra-low-power architecture is intended for portable applications where energy efficiency, USB connectivity, and compact PCB area are important.

The device combines 64 KB of Flash with 48 MHz processing capability, while integrating USB 2.0 full-speed device functionality and comprehensive analog resources. These characteristics make it suitable for USB-connected accessories, compact data-acquisition equipment, sensor interfaces, human-interface devices, and low-power embedded control systems. A -40°C to +105°C operating range supports industrial temperature requirements.

The Kinetis KL27 architecture is organized around an Arm Cortex-M0+ processor core, which supports efficient event-driven control while avoiding the resource demands of a higher-complexity core. USB device operation provides a standardized interface for data exchange, configuration, and control without requiring a separate USB interface IC. The 32-QFN package reduces board footprint but requires careful exposed-pad soldering and thermal-layout practices.

Typical implementations include USB-connected measurement modules, compact industrial sensors, wearable accessories, programming interfaces, and embedded control boards. For USB designs, the device should be paired with the required USB transceiver, routing, protection, and connector implementation. Firmware can then use the integrated USB device controller and general-purpose peripherals to manage control traffic and application-specific behavior.

PCB design should preserve the manufacturer’s recommended grounding, decoupling, exposed-pad, and USB-signal layouts. Place input and bulk decoupling capacitors close to the supply pins, connect the exposed pad to the ground plane with adequate thermal vias, and route USB D+ and D- as a controlled-impedance differential pair. Confirm crystal, clock, and USB interface requirements against the manufacturer reference manual before finalizing the schematic.

This product overview combines the key electrical, packaging, USB, memory, and thermal facts with practical PCB guidance. It also distinguishes same-footprint family options by Flash capacity or ordering code, helping engineers choose the correct Kinetis KL27 configuration without changing the established 32-QFN board footprint.

Drop-in-Alternativen für MKL27Z64VFM4 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Varianten dieser Serie

Modelle derselben Serie, die drop-in-kompatibel sind mit MKL27Z64VFM4 (gleiche Bauform und Footprint) – abweichend in Maximum CPU Frequency, Operating Temperature, Package.

NXP Semiconductors
Maximum CPU Frequency: 50 MHz
Operating Temperature: -40C to +105C (Industrial)
Package: 32-QFN-EP (5x5 mm)
Vergleichen mit MKL27Z64VFM4 →

MKL27Z32VFM4

✅ Drop-In
📦 32-QFN (5 x 5 mm)
Flash memory is 32 KB instead of 64 KB, a 50% reduction, while the Kinetis KL27 VFM package format is retained.

📋 Referenzalternative (nicht im Katalog)

MKL27Z128VFM4

✅ Drop-In
📦 32-QFN (5 x 5 mm)
Flash memory is 128 KB instead of 64 KB, a 100% increase, while the Kinetis KL27 VFM package format is retained.

📋 Referenzalternative (nicht im Katalog)

MKL27Z32VFT4

✅ Drop-In
📦 32-QFN (5 x 5 mm)
Flash memory is 32 KB instead of 64 KB, a 50% reduction, with a different ordering-code temperature or grade designation.

📋 Referenzalternative (nicht im Katalog)

MKL27Z64VFT4

✅ Drop-In
📦 32-QFN (5 x 5 mm)
Flash and CPU frequency match at 64 KB and 48 MHz, while the ordering code identifies a different grade or ordering configuration.

📋 Referenzalternative (nicht im Katalog)

MKL27Z32VMP4

✅ Drop-In
📦 32-QFN (5 x 5 mm)
Flash memory is 32 KB instead of 64 KB, a 50% reduction, with a different ordering-code grade designation.

📋 Referenzalternative (nicht im Katalog)

MKL27Z64VMP4

✅ Drop-In
📦 32-QFN (5 x 5 mm)
Flash and CPU frequency match at 64 KB and 48 MHz, while the ordering code identifies a different grade or ordering configuration.

📋 Referenzalternative (nicht im Katalog)

MKL27Z64VFM4 Grenzwerte & elektrische Eigenschaften

Product Type 32-bit ARM Cortex-M0+ microcontroller
Product Family Kinetis KL27
Processor Core Arm Cortex-M0+
Maximum CPU Frequency 48 MHz
Flash Memory 64 KB (64K x 8)
Data Width 32-bit
USB Controller USB 2.0 full-speed device controller
Gehäuse 32-QFN (5 x 5 mm)
Montageart Surface mount
Betriebstemperatur -40°C to +105°C
Analog Capability Comprehensive analog integration
Power Class Ultra-low-power

MKL27Z64VFM4 32-qfn (5 x 5 mm) Pinbelegungsleitfaden

Pinbelegung für MKL27Z64VFM4 (32-qfn (5 x 5 mm)-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.

Pinbelegungsdiagramm für MKL27Z64VFM4 im 32-qfn (5 x 5 mm)-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für MKL27Z64VFM4.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

MKL27Z64VFM4 ist geeignet für 6 Anwendungs: USB Sensor Node, Compact Data-Acquisition Module, Portable Medical Accessory, USB Human-Interface Device, Industrial Control Module, Low-Power IoT Peripheral.

🧩

USB Sensor Node

The MKL27Z64VFM4 fits a USB-connected sensor node because its 48 MHz Arm Cortex-M0+ core can service control traffic and local measurements while 64 KB of Flash provides room for application firmware. The integrated USB 2.0 full-speed device controller reduces the need for a separate interface IC. Place the MCU near the USB connector and transceiver, use a controlled-impedance D+ and D- pair, and provide local decoupling at each supply pin. The -40°C to +105°C range also permits deployment in industrial sensing environments where enclosure temperature can rise well above room temperature.

📊

Compact Data-Acquisition Module

The MKL27Z64VFM4 supports compact data-acquisition modules that require local control, USB data transfer, and mixed-signal support in a small board area. Its 48 MHz Cortex-M0+ core handles sampling sequencing, buffering, and communications, while the Kinetis KL27 family provides comprehensive analog integration. The 64 KB Flash capacity is suitable for firmware that includes USB descriptors, calibration routines, and a communication protocol. A 32-QFN footprint reduces component count, but engineers should allocate exposed-pad vias, controlled-impedance USB routing, and supply filtering from the initial layout.

💊

Portable Medical Accessory

The MKL27Z64VFM4 can serve as the control hub in a portable medical accessory connected to a host over USB. Its low-power Cortex-M0+ architecture and 64 KB of Flash support firmware for device identification, configuration, status reporting, and control of external sensors or actuators. The full-speed USB device function enables a standardized connection to a computer or embedded host. For medical equipment, validate the complete signal chain, isolation strategy, firmware risk controls, and applicable regulatory requirements. The MCU's -40°C to +105°C range supports varied operating environments, but it does not by itself establish medical certification.

🔧

USB Human-Interface Device

The MKL27Z64VFM4 is suitable for a compact USB keyboard, control panel, configuration interface, or other human-interface accessory. The 48 MHz Cortex-M0+ core provides sufficient control bandwidth for debouncing, LED management, HID reporting, and USB enumeration, while 64 KB of Flash accommodates boot code, descriptors, and application logic. The integrated full-speed USB device controller simplifies the system architecture. Place the MCU and transceiver close to the connector, maintain continuous USB trace impedance, provide ESD protection, and route away from motor, relay, or switching-regulator nodes to limit conducted and radiated interference.

🏭

Industrial Control Module

The MKL27Z64VFM4 supports industrial control modules that combine local logic with USB service communications. Its 48 MHz processing rate handles routine control tasks, while the integrated analog resources can simplify signal conditioning and supervision around the MCU. The -40°C to +105°C operating range is useful in factory equipment, building controls, and process monitoring. Designers should identify every peripheral and alternate-function assignment from the exact device documentation, use robust input protection, and separate analog, digital, and USB return paths. The 32-QFN exposed pad should be tied to ground through multiple thermal vias to maintain reliable performance at elevated temperature.

🧩

Low-Power IoT Peripheral

The MKL27Z64VFM4 can be used in a low-power IoT peripheral that wakes to acquire data, performs local processing, and exchanges information over USB. Its ultra-low-power Kinetis KL27 positioning is appropriate for portable equipment where continuous active energy use is undesirable, while 64 KB of Flash provides a practical firmware budget. Configure peripherals and the clock tree for the duty cycle, use low-leakage sensors, and isolate USB circuitry so it does not add unnecessary quiescent load. Firmware should use the low-power modes specified by NXP and test wake, suspend, and bus-disconnect behavior across the full -40°C to +105°C temperature range.

Zusammenfassung der empfohlenen Produkte

MKL27Z128VFM4 Same-family option with 128 KB Flash for larger sensor firmware Verwendet in: USB Sensor Node, Compact Data-Acquisition Module, Industrial Control Module MKL27Z32VFM4 Lower-memory same-family option for compact sensing code Verwendet in: USB Sensor Node, Low-Power IoT Peripheral MKL27Z64VFT4 Same-family 64 KB option with a different ordering-code grade Verwendet in: Compact Data-Acquisition Module, Industrial Control Module MKL27Z32VMP4 Same-family lower-memory option for minimal accessory firmware Verwendet in: Portable Medical Accessory MKL27Z64VMP4 Same-family option with matching Flash capacity Verwendet in: Portable Medical Accessory, USB Human-Interface Device, Low-Power IoT Peripheral MKL27Z32VFT4 Lower-memory option for simple HID firmware Verwendet in: USB Human-Interface Device
What are the key specifications of MKL27Z64VFM4 that engineers should know?
The MKL27Z64VFM4 combines a 48 MHz Arm Cortex-M0+ core, 64 KB of Flash, a USB 2.0 full-speed device controller, and comprehensive analog integration in a 32-QFN 5 x 5 mm package. According to the NXP product page, it is an active ultra-low-power Kinetis KL27 microcontroller. Its -40°C to +105°C temperature range makes it suitable for industrial as well as commercial portable equipment.
Where can I download the MKL27Z64VFM4 datasheet PDF?
The MKL27Z64VFM4 documentation is available from the official NXP product page and the KL27 sub-family reference manual. The product page identifies the device as an active 48 MHz Kinetis KL27 MCU with 64 KB Flash and a USB 2.0 full-speed device controller. Use the manufacturer datasheet for the definitive electrical limits, package drawings, and pin descriptions before releasing a PCB design.
Where can I find the MKL27Z64VFM4 pinout and 32-QFN footprint?
Use the package drawing and pin-description table in the NXP MKL27Z64VFM4 documentation to locate every 32-QFN connection. The component is identified as a 32-QFN 5 x 5 mm device with an exposed pad. Do not infer the pinout from another package variant, and use the manufacturer land pattern for the exposed-pad soldering and thermal-via requirements.
What is the MKL27Z64VFM4 used for?
The MKL27Z64VFM4 is used for compact, low-power embedded products requiring a 48 MHz Arm Cortex-M0+ processor, 64 KB Flash, and USB device connectivity. NXP identifies comprehensive analog integration as a key feature of the Kinetis KL27 family. Typical roles include USB sensor nodes, compact data-acquisition modules, human-interface accessories, and portable industrial controls.
Does MKL27Z64VFM4 support USB?
Yes. The MKL27Z64VFM4 includes a USB 2.0 full-speed device controller. This allows the microcontroller to communicate as a USB device while retaining a 48 MHz Arm Cortex-M0+ core and 64 KB of Flash. The external design still requires the appropriate USB transceiver, connector protection, impedance-controlled routing, and power-supply implementation.
What is the operating temperature range of MKL27Z64VFM4?
The MKL27Z64VFM4 is specified for -40°C to +105°C operation. This range covers industrial temperature environments in addition to room-temperature consumer applications. Maintain suitable decoupling and thermal design across the complete range, particularly when the 32-QFN exposed pad is the primary path for removing heat from the device.
MKL27Z64VFM4 vs MKL27Z128VFM4: which is better for my design?
Choose MKL27Z64VFM4 when 64 KB of Flash is sufficient, and choose MKL27Z128VFM4 when firmware growth requires 128 KB. Both devices appear in the same NXP Kinetis KL27 family and use the 32-QFN 5 x 5 mm ordering format identified for the target. Confirm peripheral, temperature, and pin details against the exact manufacturer ordering table before substituting.
When should I choose MKL27Z64VFM4 over MKL27Z32VFM4?
Choose MKL27Z64VFM4 when your application needs more code and data storage than the 32 KB option in MKL27Z32VFM4. Both belong to the Kinetis KL27 family and use the same VFM package designation, making them closely related options for a 32-QFN design. Select according to firmware size, USB requirements, peripheral needs, lifecycle requirements, and the exact temperature grade.
What is the best drop-in replacement for MKL27Z64VFM4?
The closest documented same-footprint options include MKL27Z32VFM4 and MKL27Z128VFM4, although the first has half the Flash and the second has twice the Flash of the 64 KB target. A drop-in decision must also confirm the USB configuration, temperature grade, peripheral set, and exposed-pad layout. No cross-brand MCU has been established as a verified pin-compatible replacement.
Can MKL27Z32VFM4 replace MKL27Z64VFM4 without changing the PCB?
The MKL27Z32VFM4 can share the VFM package format and may fit an existing 32-QFN layout, but it provides only 32 KB of Flash versus 64 KB in the MKL27Z64VFM4. A footprint match alone does not guarantee a functional drop-in replacement. Confirm that the reduced memory budget is adequate and that all electrical, USB, peripheral, and temperature requirements remain satisfied.
What can replace MKL27Z64VFM4?
The most defensible replacements are closely related Kinetis KL27 devices such as MKL27Z32VFM4 and MKL27Z128VFM4 because the manufacturer supports them in the same family documentation and VFM package format. Cross-brand alternatives can differ in USB implementation, memory map, peripherals, tooling, and firmware support. Validate the complete pin, clock, power, USB, and software compatibility rather than relying only on package dimensions.
Is MKL27Z64VFM4 the same as MKL27Z128VFM4?
No. Both are 32-QFN 5 x 5 mm Kinetis KL27 family members, but their Flash capacities differ: MKL27Z64VFM4 has 64 KB while MKL27Z128VFM4 has 128 KB. The larger device is not an exact functional equivalent. It can serve as a capacity-oriented same-footprint option only after checking the exact pinout, USB features, temperature grade, and firmware configuration.
Where can I buy MKL27Z64VFM4 online?
Use the Request a Quote form on this page to request MKL27Z64VFM4 pricing, stock confirmation, and lead time. The quote team can confirm the exact 32-QFN ordering configuration and current availability. For production planning, request the quantity break, date code, and shipment schedule together so assembly and sourcing commitments remain aligned.
What is the price of MKL27Z64VFM4?
The current price of MKL27Z64VFM4 should be obtained through the Request a Quote form on this page because commercial pricing and availability can change with quantity and market conditions. Submit the required order quantity and target package or reel configuration. The quote response will provide the applicable unit price, availability, and expected lead time for the exact MPN.
What is the lead time for MKL27Z64VFM4?
Current lead time for MKL27Z64VFM4 should be confirmed through the Request a Quote form on this page. Provide the annual and per-order quantities, required package orientation, target shipment date, and approved alternate-part policy. This allows sourcing to return a realistic production schedule for the exact 32-QFN 5 x 5 mm device.
Is MKL27Z64VFM4 in stock?
Current MKL27Z64VFM4 stock status should be confirmed with the Request a Quote form on this page. Include your required quantity and target delivery date in the request. NXP lists the MPN as active, but lifecycle status and practical procurement availability should both be considered when planning a new production build.
What PCB layout considerations apply to MKL27Z64VFM4?
The MKL27Z64VFM4 layout should follow the manufacturer reference manual for the 32-QFN 5 x 5 mm package and exposed pad. Place decoupling capacitors close to their supply pins, provide a low-impedance ground connection through thermal vias, and route USB D+ and D- as a matched differential pair away from noisy switching nodes. Review signal-integrity and return-path continuity with the final stack-up.

Technische Referenzdaten für MKL27Z64VFM4 – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose MKL27Z64VFM4 when your compact USB product needs a 48 MHz Arm Cortex-M0+ core, 64 KB of Flash, full-speed USB device connectivity, and a 32-QFN 5 x 5 mm footprint. Select MKL27Z32VFM4 when 32 KB is sufficient and memory cost or capacity matters; verify the linker layout and application update path. Choose MKL27Z128VFM4 when firmware expansion, logging, or protocol support requires 128 KB. MKL27Z64VFT4 and MKL27Z64VMP4 match the target's 64 KB Flash and 48 MHz CPU configuration, so their ordering-code temperature or grade differences determine which is appropriate. All listed alternatives remain within the Kinetis KL27 family, reducing firmware-porting risk, but exact pin assignments, USB configuration, peripheral availability, and environmental ratings must still be checked. No cross-brand replacement is recommended without a separate board-level compatibility review.

Vergleich mit Alternativen

Parameter Dieses Produkt MKL27Z32VFM4 MKL27Z128VFM4 MKL27Z32VFT4 MKL27Z64VFT4 MKL27Z32VMP4
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
Package 32-QFN (5 x 5 mm) 32-QFN (5 x 5 mm) 32-QFN (5 x 5 mm) 32-QFN (5 x 5 mm) 32-QFN (5 x 5 mm) 32-QFN (5 x 5 mm)
Product Family Kinetis KL27 Kinetis KL27 Kinetis KL27 Kinetis KL27 Kinetis KL27 Kinetis KL27
Processor Core Arm Cortex-M0+ Arm Cortex-M0+ Arm Cortex-M0+ Arm Cortex-M0+ Arm Cortex-M0+ Arm Cortex-M0+
Maximum CPU Frequency 48 MHz 48 MHz 48 MHz 48 MHz 48 MHz 48 MHz
Flash Memory 64 KB 32 KB 128 KB 32 KB 64 KB 32 KB
USB Controller USB 2.0 full-speed device USB 2.0 full-speed device USB 2.0 full-speed device USB 2.0 full-speed device USB 2.0 full-speed device USB 2.0 full-speed device
Power Class Ultra-low-power Ultra-low-power Ultra-low-power Ultra-low-power Ultra-low-power Ultra-low-power

Wichtigste Unterscheidungsmerkmale

  • Balanced Flash capacity for compact USB firmware (vs. MKL27Z32VFM4)
  • Lower Flash demand when 64 KB is sufficient (vs. MKL27Z128VFM4)
  • Same Kinetis KL27 CPU and USB foundation (vs. MKL27Z64VFT4)
  • Matches the 64 KB memory configuration of the VMP ordering option (vs. MKL27Z32VMP4)

Designhinweise

Follow the NXP 32-QFN land pattern and exposed-pad recommendations exactly. Place the exposed pad on a solid ground-plane region and connect it with several thermal vias to reduce junction-to-ambient resistance. Avoid placing tall components or mechanical hardware over the pad, and maintain adequate copper around the package. Also preserve the manufacturer-defined keepout beneath the device because removing the thermal ground connection can increase operating temperature and reduce long-term reliability.

Route USB D+ and D- as a short, continuous, impedance-controlled differential pair. Reference the pair to a continuous ground plane, minimize vias and stubs, and keep the pair away from switching nodes, high-current return paths, crystal circuitry, and antenna keepouts. Confirm the target trace impedance against the final PCB stack-up and USB implementation guidance. ESD protection should be placed close to the connector while maintaining the required signal return geometry.

Place the required bulk and local decoupling capacitors close to their associated supply pins, with the shortest possible ground connections. Separate sensitive analog and digital return currents where the device pin assignments permit it, and connect analog ground to the main ground plane at a controlled location. Review the reference manual for the exact supply pins, capacitor values, and startup sequencing before populating the board; capacitor requirements should follow the manufacturer guidance rather than generic rules.

Do not treat an identical 32-QFN outline as proof of a functional drop-in replacement. The suffix can encode Flash capacity, temperature grade, or another ordering attribute. For MKL27Z32VFM4 and MKL27Z128VFM4, verify memory capacity, USB requirements, alternate functions, clock setup, exposed-pad construction, and software configuration. Firmware built for a 64 KB device may require linker and memory-map changes when moving to the 32 KB option.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

NXP lists the MKL27Z64VFM4 as active. Specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not identified in the available product information and require confirmation from the manufacturer or current material-compliance documentation.

Daten verifiziert am: 2026-11-14 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

MKL27Z64VFM4 datasheet MKL27Z64VFM4 datasheet pdf MKL27Z64VFM4 pinout MKL27Z64VFM4 footprint MKL27Z64VFM4 equivalent MKL27Z64VFM4 replacement MKL27Z64VFM4 cross reference MKL27Z64VFM4 vs MKL27Z128VFM4 MKL27Z64VFM4 vs MKL27Z32VFM4 NXP MKL27Z64VFM4 MKL27Z64VFM4 price MKL27Z64VFM4 stock MKL27Z64VFM4 48MHz USB MKL27Z64VFM4 32-QFN application circuit MKL27Z64VFM4 schematic

Verwandte Bauteile & Begriffe

NXP Semiconductors MKL27Z64VFM4 MKL27Z32VFM4 MKL27Z128VFM4 MKL27Z32VFT4 MKL27Z64VFT4 MKL27Z32VMP4 MKL27Z64VMP4 Kinetis KL27 Arm Cortex-M0+ 32-bit microcontroller MCU embedded controller embedded processor semiconductor ultra-low-power MCU USB 2.0 full-speed device controller 64 KB Flash 48 MHz 32-QFN QFN family surface mount SMD USB sensor node industrial control module
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen