PIC16C57-10/P - 8-Bit OTP MCU 3KB EPROM 20 I/O | Microchip
Teilenummer: PIC16C57-10/P ✗ Abgekündigt| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $5.19 | $5,19 |
| 10 | $4.65 | $46,50 |
| 100 | $3.95 | $395,00 |
| 500 | $3.45 | $1.725,00 |
| 1.000 | $2.95 | $2.950,00 |
PIC16C57-10/P Übersicht
An 8-bit microcontroller (MCU) is a single-chip processor that integrates a CPU, program memory, data memory, and peripheral I/O onto one die. Within the broader hierarchy, the PIC16C57 belongs to the category of 8-bit microcontrollers -> microcontrollers -> microprocessors -> digital ICs -> semiconductors. The 'C' in PIC16C57 designates the OTP/EPROM program memory variant (vs. 'F' for Flash and 'HV' for high-voltage variants), making it one-time field-programmable using a device programmer such as the MPLAB PM3.
Key features of the PIC16C57-10/P include a 12-bit wide instruction set with 8-bit data path, two-level deep hardware stack, direct/indirect/relative addressing modes, and a single 8-bit real-time counter/timer (TMR0). It supports seven or eight special-function hardware registers (SFRs) depending on configuration, and provides a watchdog timer for reliable standalone operation. The CMOS process delivers low quiescent current suitable for battery-powered or always-on applications.
The PIC16C57-10 architecture is a classic Harvard design with separate program and data buses, enabling simultaneous instruction fetch and data access. The RISC core executes most instructions in a single cycle, delivering approximately 5 MIPS at 10MHz - an order of magnitude above contemporaries in the same price class. The 2:1 code compression relative to other 8-bit MCUs reduces program memory pressure for the 3KB EPROM.
Typical applications include industrial control logic, appliance controllers, simple sensor interfaces, automotive body electronics (non-safety), low-end consumer devices, and legacy embedded systems. Designers often choose the PIC16C57-10/P for cost-sensitive applications where the OTP memory model is acceptable and the 20 I/O count fits the system needs.
When designing with this device, note that OTP memory cannot be reprogrammed in-circuit - a programmed device cannot be erased, only replaced. For prototype or iterative-development workflows, a Flash variant (PIC16F57) is recommended. Always include decoupling capacitors within 5mm of VDD/VSS pins.
This page synthesizes distributor pricing, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet, with cross-references to same-family and cross-brand equivalents.
Drop-in-Alternativen für PIC16C57-10/P – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit PIC16C57-10/P (gleiche Bauform und Footprint) – abweichend in Package, Program Memory Size, Timers, Program Memory Type, Mounting Type.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
PIC16C57-10I/P
✅ Drop-In✓ Auf Lager
$1.75 / Stück
Datenblatt ansehen →PIC16C57-20/P
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC16F57-I/P
✅ Drop-In✓ Auf Lager
$1.18 / Stück
Datenblatt ansehen →PIC16C57T-10/SS
✅ Drop-In✓ Auf Lager
$1.95 / Stück
Datenblatt ansehen →PIC16C56-10/P
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC16C55-10/P
✅ Drop-In✓ Auf Lager
$3.65 / Stück
Datenblatt ansehen →PIC16C57-10/P Grenzwerte & elektrische Eigenschaften
| Core | PIC 8-bit RISC |
| Series | PIC16C5x |
| Program Memory Type | OTP EPROM |
| Program Memory Size | 3KB (2K x 12) |
| RAM Size | 72 bytes |
| Datenbusbreite | 8-bit |
| Instruction Bus Width | 12-bit |
| Maximale Taktfrequenz | 10 MHz |
| Versorgungsspannung | 3.0 V to 5.5 V (3.3V / 5V nominal) |
| I/O Pins | 20 |
| Timers | 1 x 8-bit (TMR0) |
| Hardware Stack Depth | 2 levels |
| Watchdog Timer | Yes |
| Gehäuse | 28-pin PDIP (0.600" / 15.24mm) |
| Montageart | Through-Hole |
| Betriebstemperatur | 0C to +70C (commercial) |
PIC16C57-10/P Pin-Konfiguration
| Pin 1 | RA2 — PORT A I/O bit 2 |
| Pin 2 | RA3 — PORT A I/O bit 3 |
| Pin 3 | |
| Pin 3 | RTCC — Real-Time Clock/Counter (TMR0) external input |
| Pin 4 | MCLR/VPP — Master Clear (reset) / Programming voltage input |
| Pin 5 | VSS — Ground reference |
| Pin 6 | RB0 — PORT B I/O bit 0 (interrupt-on-change capable) |
| Pin 7 | RB1 — PORT B I/O bit 1 |
| Pin 8 | RB2 — PORT B I/O bit 2 |
| Pin 9 | RB3 — PORT B I/O bit 3 |
| Pin 10 | RB4 — PORT B I/O bit 4 |
| Pin 11 | RB5 — PORT B I/O bit 5 |
| Pin 12 | RB6 — PORT B I/O bit 6 |
| Pin 13 | RB7 — PORT B I/O bit 7 |
| Pin 14 | VSS — Ground reference |
| Pin 15 | OSC1 — Oscillator input / external clock input |
| Pin 16 | OSC2 — Oscillator output (crystal mode) |
| Pin 17 | RC0 — PORT C I/O bit 0 |
| Pin 18 | RC1 — PORT C I/O bit 1 |
| Pin 19 | RC2 — PORT C I/O bit 2 |
| Pin 20 | RC3 — PORT C I/O bit 3 |
| Pin 21 | RC4 — PORT C I/O bit 4 |
| Pin 22 | RC5 — PORT C I/O bit 5 |
| Pin 23 | RC6 — PORT C I/O bit 6 |
| Pin 24 | RC7 — PORT C I/O bit 7 |
| Pin 25 | VDD — Positive supply voltage (3.0 V to 5.5 V) |
| Pin 26 | VDD — Positive supply voltage |
| Pin 27 | RA0 — PORT A I/O bit 0 |
| Pin 28 | RA1 — PORT A I/O bit 1 |
Typische Anwendungen
PIC16C57-10/P ist geeignet für 6 Anwendungs: Industrial Control Logic, Appliance Control Boards, Simple Sensor Interface Nodes, Automotive Body Electronics (Non-Safety), Low-End Consumer Electronics, Legacy Embedded System Maintenance.
Industrial Control Logic
The PIC16C57-10/P fits industrial control logic designs where deterministic 8-bit RISC performance and low cost outweigh in-field reprogrammability. Its 10MHz core delivers approximately 5 MIPS, sufficient for sequential state machines, relay drivers, and timing controllers in PLCs and machine automation. The 20 I/O pins handle multi-zone sensor polling, while the on-chip watchdog timer recovers from EMI-induced lockups in factory-floor environments. Operating from 3.0V to 5.5V, the MCU accepts 24V industrial rails after a regulator. The 28-pin PDIP package remains a strong fit for control cabinets where through-hole serviceability matters more than board density.
Empfohlen
Appliance Control Boards
Appliance controllers in washing machines, microwave ovens, dishwashers, and HVAC units are a classic application for the PIC16C57-10/P. Its 3KB OTP EPROM holds keypad scan routines, motor-control state machines, and timer logic for white-goods products. The 25 mA per-pin drive capability directly switches indicator LEDs, small solenoid valves, and buzzer transducers without external drivers. CMOS low quiescent current keeps standby consumption compliant with energy-efficiency regulations. The 28-pin PDIP package is straightforward for wave-soldered production boards common in appliance manufacturing. Designers value the deterministic interrupt response for safety-critical timing such as door-lock interlocks and over-temperature shutdowns.
Empfohlen
Simple Sensor Interface Nodes
Low-cost sensor-interface nodes for HVAC, building automation, and remote telemetry benefit from the PIC16C57-10/P's combination of 20 I/O, 3KB EPROM, and CMOS low power. The MCU reads multiple digital sensors (PIR motion, magnetic reed switches, thermistor networks via ADC-free voltage dividers) and drives relay or transistor output stages. With a 10MHz clock, the part completes sensor sweeps and debounce routines well under 100 ms, ensuring responsive event handling. The OTP memory model suits sealed-field deployments where firmware tampering is undesirable. The 3.0 V to 5.5 V supply range accommodates both battery stacks and rectified mains adapters with a simple zener regulator.
Empfohlen
Automotive Body Electronics (Non-Safety)
Non-safety automotive body electronics - interior lighting controllers, mirror adjusters, accessory timers, and door-module logic - historically used the PIC16C57-10/P. The 28-pin PDIP footprint and 20 I/O handle multiple lamp drivers and switch inputs. For new designs, however, the commercial temperature grade (0C to +70C) is insufficient; automotive applications require the PIC16C57-10I/P (industrial) or AEC-Q100-qualified successors. Designers should note that this part is NRND and not recommended for new automotive designs, where modern PIC16F193x or dsPIC33 families provide qualified alternatives with CAN/LIN peripherals.
Empfohlen
Low-End Consumer Electronics
Cost-sensitive consumer products such as remote controls, toy electronics, novelty gadgets, and entry-level timers are ideal applications for the PIC16C57-10/P. Its 3KB OTP EPROM is sufficient for IR protocol encoding, button matrix scanning, LED chase patterns, and simple melody generators. The 20 I/O directly drive segment displays or RGB LEDs, while the CMOS core draws under 2 mA active, extending battery life in portable devices. OTP memory prevents firmware cloning - a plus for protecting proprietary protocols. For high-volume consumer goods where every penny matters, the PIC16C57-10/P remains a workhorse part despite its NRND status on Microchip's roadmap.
Empfohlen
Legacy Embedded System Maintenance
Many legacy industrial, scientific, and medical devices still operate with PIC16C57-10/P controllers and require periodic replacement or refurbishment. The 28-pin PDIP through-hole form factor supports socketed boards where individual MCU swaps are feasible without desoldering. Stockpile management for NRND parts is a real concern; this part is currently available at Heisener (33,600 pieces as of 2026-09-17) but availability will diminish. For maintenance, the PIC16C57-10I/P and PIC16F57-I/P serve as pin-compatible replacements that accept the same HEX firmware after minor configuration-bit adjustments documented in Microchip migration guides.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PIC16C57-10/P – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PIC16C57-10I/P | PIC16C57-20/P | PIC16F57-I/P | PIC16C56-10/P | PIC16C55-10/P |
|---|---|---|---|---|---|---|
| Package | 28-pin PDIP (0.600") | 28-pin PDIP (0.600") - same | 28-pin PDIP (0.600") - same | 28-pin PDIP (0.600") - same | 28-pin PDIP (0.600") - same | 28-pin PDIP (0.600") - same |
| Brand | Microchip Technology | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same |
| Program Memory | 3KB (2K x 12) OTP EPROM | 3KB (2K x 12) OTP EPROM - identical | 3KB (2K x 12) OTP EPROM - identical | 3KB Flash - same size, Flash technology | 1KB (512 x 12) OTP EPROM - smaller | 1KB (512 x 12) OTP EPROM - smaller |
| RAM Size | 72 bytes | 72 bytes - identical | 72 bytes - identical | 72 bytes - identical | 32 bytes - smaller | 24 bytes - smaller |
| Max Clock Frequency | 10 MHz | 10 MHz - identical | 20 MHz - 2x faster | 20 MHz - 2x faster | 10 MHz - identical | 10 MHz - identical |
| Memory Type | OTP EPROM | OTP EPROM - same | OTP EPROM - same | Flash - reprogrammable | OTP EPROM - same | OTP EPROM - same |
| Operating Temperature | 0C to +70C | -40C to +85C industrial | 0C to +70C - same | -40C to +85C industrial | 0C to +70C - same | 0C to +70C - same |
| Lifecycle Status | NRND | NRND | NRND | Active | NRND | NRND |
Wichtigste Unterscheidungsmerkmale
- 3KB OTP EPROM is double the program memory of the PIC16C56-10/P (vs. PIC16C56-10/P)
- Flash-based sibling PIC16F57-I/P offers in-circuit reprogrammability (vs. PIC16F57-I/P)
- 20 I/O pins versus PIC16F84A's 13 (vs. PIC16F84A)
- Commercial temp grade is sufficient for most non-automotive applications (vs. PIC16C57-10I/P (industrial))
Designhinweise
Place a 100 nF ceramic decoupling capacitor within 5 mm of each VDD pin (pins 25 and 26) and a bulk 10 uF tantalum or aluminum electrolytic capacitor on the supply rail. The PIC16C57-10/P operates from 3.0 V to 5.5 V; for noisy industrial environments, add a ferrite bead in series with VDD and a TVS diode (e.g., SMAJ5.0A) for transient protection. Estimated: total quiescent current is approximately 1.5 mA active at 5V/10MHz; deep sleep equivalent is below 1 uA when applicable.
Route the oscillator traces (OSC1/OSC2) symmetrically and keep them short - under 10 mm if possible - to minimize EMI and stray capacitance. Place the crystal or resonator as close to the MCU as the layout allows, with a guard ground trace on each side. Avoid routing signal traces under the crystal. For HS (high-speed) oscillator mode above 4 MHz, a parallel resistor (100 k ohm to 1 M ohm) across the crystal may be required per Microchip AN588 to stabilize oscillation start-up.
OTP EPROM memory cannot be erased once programmed - any firmware bug in production is a write-off. Mitigate by programming known-good golden units first, validating with a socketed prototype (use the 28-pin PDIP package to enable IC swap), and maintaining firmware revision control. Also note that the two-level hardware stack limits call nesting to two deep - any function calling a function will corrupt the return address. Restructure code iteratively rather than recursively.
The MCLR/VPP pin (pin 4) should be pulled up to VDD through a 10 k ohm resistor to prevent spurious resets. Add a 100 nF capacitor from MCLR to VSS to filter noise spikes; values above 1 uF slow the VPP rise time during programming and may cause programming failures. Keep the MCLR trace short and away from high-frequency switching signals. For in-system programming headers, isolate the VPP line from the rest of the circuit to avoid contention.
Each PIC16C57-10/P I/O pin can source or sink up to 25 mA, but the total port current is limited (typically 100 mA per port and 200 mA for VDD). When driving multiple LEDs or relays, distribute the load across PORT A, B, and C to avoid exceeding aggregate limits. Use a logic-level MOSFET (e.g., 2N7002) to buffer high-current loads rather than driving them directly from the MCU pin to extend reliability.
Compliance-Informationen
RoHS and REACH compliance not explicitly confirmed in the provided data; the PIC16C57-10/P is a legacy product launched before widespread RoHS adoption. PIC16C57 family is NOT AEC-Q100 qualified - use PIC16C57-10I/P suffix for industrial temp only, not automotive.
