PIC16LC62B-04/SP - 4MHz 8-Bit OTP MCU, 3.5KB | Microchip
Teilenummer: PIC16LC62B-04/SP ✗ Abgekündigt| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $6.4 | $6,40 |
| 10 | $5.85 | $58,50 |
| 100 | $5.1 | $510,00 |
| 500 | $4.45 | $2.225,00 |
| 1.000 | $3.9 | $3.900,00 |
PIC16LC62B-04/SP Übersicht
An 8-bit microcontroller (MCU) is a single-chip computer containing a CPU, program memory (ROM/EPROM/Flash), data memory (RAM), and configurable I/O peripherals on one die. Within the broader hierarchy, the PIC16LC62B belongs to the PIC16C family of RISC microcontrollers, which falls under the 8-bit MCU category, itself a subset of embedded computing and digital ICs. The 8-bit MCU class targets cost-sensitive, low-to-moderate-complexity control tasks such as sensor interfacing, simple user I/O, and timer-driven control loops.
Key features include 35 single-cycle instructions (with only program branches taking two cycles), a 4 MHz external oscillator interface, an internal watchdog timer, and 22 general-purpose I/O pins multiplexed with on-chip peripherals. The Harvard architecture separates program and data buses, allowing instruction fetch and operand read in a single 200 ns cycle. On-chip peripherals include a Timer0 8-bit timer/counter with an 8-bit prescaler, Timer1 16-bit timer/counter, and capture/compare/PWM (CCP) modules.
The PIC16LC62B implements Microchip's enhanced mid-range 14-bit instruction set, providing greater code density than the baseline 12-bit PIC cores while retaining upward compatibility. EPROM (erasable programmable read-only memory) allows windowed-package parts to be erased with UV light for development, while OTP (one-time programmable) versions are intended for production programming where re-programmability is not required.
Typical applications include low-power sensor interface boards, simple appliance control modules, hobby and educational microcontroller projects, replacement of discrete logic in legacy designs, and embedded timing/sequencing circuits. The wide 3.3V/5V supply range enables both battery-powered and mains-powered designs.
When designing with this device, note that the 28-SPDIP through-hole footprint requires through-hole PCB assembly rather than reflow soldering. Programming requires a Microchip device programmer (e.g., PICkit or MPLAB PM3) and the OTP variant can only be programmed once.
This page synthesizes verified distributor inventory data, parametric comparison with same-package Microchip drop-in alternatives, and practical design notes that go beyond the manufacturer's datasheet alone.
Drop-in-Alternativen für PIC16LC62B-04/SP – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit PIC16LC62B-04/SP (gleiche Bauform und Footprint) – abweichend in Program Memory Size, Instruction Cycle Time, Operating Temperature Range, Program Memory Type, RoHS Status.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
PIC16C62B-04/SP
✅ Drop-In✓ Auf Lager
$4.65 / Stück
Datenblatt ansehen →PIC16LC621A-04I/P
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$1.01 / Stück
Datenblatt ansehen →PIC16LC620A-04/P
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$1.3 / Stück
Datenblatt ansehen →PIC16LC62B-04/SP Grenzwerte & elektrische Eigenschaften
| Product Family | PIC16C (PIC16LC6x series) |
| Core | 8-bit PIC RISC |
| Architecture | Harvard, 14-bit instruction word |
| Maximale Taktfrequenz | 4 MHz |
| Instruction Cycle Time | 200 ns |
| Program Memory Type | OTP EPROM |
| Program Memory Size | 3.5 KB (2K x 14) |
| Data Memory (RAM) | 128 bytes (128 x 8) |
| Number of I/O Pins | 22 |
| Supply Voltage Range | 3.3 V / 5 V (low-voltage 'LC' variant) |
| Gehäuse / Bauform | 28-SPDIP (Skinny DIP, 0.300 inch / 7.62 mm row spacing) |
| Oscillator Type | External |
| Montageart | Through-Hole |
| Packaging | Tube |
| MSL-Level | Not applicable (through-hole package) |
PIC16LC62B-04/SP Pin-Konfiguration
| Pin 1 | /MCLR — Master Clear (reset) input, active-low |
| Pin 2 | RA0/AN0 — PORTA bit 0 / analog input 0 |
| Pin 3 | RA1/AN1 — PORTA bit 1 / analog input 1 |
| Pin 4 | RA2/AN2 — PORTA bit 2 / analog input 2 |
| Pin 5 | RA3/AN3/VREF — PORTA bit 3 / analog input 3 / voltage reference |
| Pin 6 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| Pin 7 | RA5/AN4/SS — PORTA bit 5 / analog input 4 / SPI slave select |
| Pin 8 | VSS — Ground reference |
| Pin 9 | OSC1/CLKIN — Oscillator input / external clock input |
| Pin 10 | OSC2/CLKOUT — Oscillator output / clock output |
| Pin 11 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator output / Timer1 clock |
| Pin 12 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator input / CCP2 |
| Pin 13 | RC2/CCP1 — PORTC bit 2 / CCP1 PWM/compare/capture |
| Pin 14 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| Pin 15 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| Pin 16 | RC5/SDO — PORTC bit 5 / SPI data out |
| Pin 17 | RC6/TX/CK — PORTC bit 6 / USART TX / clock |
| Pin 18 | RC7/RX/DT — PORTC bit 7 / USART RX / data |
| Pin 19 | VSS — Ground reference |
| Pin 20 | RD0 — PORTD bit 0 |
| Pin 21 | RD1 — PORTD bit 1 |
| Pin 22 | RD2 — PORTD bit 2 |
| Pin 23 | RD3 — PORTD bit 3 |
| Pin 24 | RD4 — PORTD bit 4 |
| Pin 25 | RD5 — PORTD bit 5 |
| Pin 26 | RD6 — PORTD bit 6 |
| Pin 27 | RD7 — PORTD bit 7 |
| Pin 28 | VDD — Positive supply voltage |
Typische Anwendungen
PIC16LC62B-04/SP ist geeignet für 6 Anwendungs: Low-Power Sensor Interface Boards, Simple Appliance Control Modules, Hobby and Educational Microcontroller Projects, Replacement of Discrete Logic in Legacy Designs, Embedded Timing and Sequencing Circuits, Industrial Control Logic Modules.
Low-Power Sensor Interface Boards
The PIC16LC62B-04/SP is well-suited to low-power sensor interface boards because its 3.3V/5V supply range and 4 MHz clock allow low quiescent draw while still meeting 200 ns instruction-cycle timing for periodic sensor sampling. The 22 digital I/O pins connect easily to digital sensors, comparators, and indicator LEDs without external multiplexer logic. Engineers typically route 4-8 I/O lines to sensors and use the CCP module to generate timing pulses for one-wire or PWM-output transducers. Trade-off: the 128-byte RAM limits buffer depth for raw ADC streams, so designers must batch samples or offload via UART.
Empfohlen
Simple Appliance Control Modules
The PIC16LC62B-04/SP fits simple appliance control modules - washing machine timers, microwave keypads, fan speed controllers - where 22 I/O pins can drive 7-segment displays, keypads, relays, and triac interfaces simultaneously. Its 3.5 KB OTP program memory holds mid-complexity state machines for cycle control and safety interlocks. The 35 single-cycle RISC instructions make cycle-timing loops deterministic, which is critical for appliance safety standards. Designers pair this MCU with opto-isolated triac drivers (e.g., MOC3041) on the AC side and a small EEPROM for user settings.
Empfohlen
Hobby and Educational Microcontroller Projects
The PIC16LC62B-04/SP is a classic teaching vehicle in university embedded-systems courses because the 28-SPDIP through-hole package fits breadboards and 0.1-inch perfboards without SMD soldering. Students can hand-wire the external oscillator (4 MHz crystal with two 22 pF caps) and program the OTP device with a PICkit 3/4 to learn Harvard architecture fundamentals. Its 35-instruction RISC set is small enough to memorize but rich enough for real I/O, timer, and interrupt exercises. Trade-off: with modern curricula favoring PIC16F or PIC18F parts, this OTP device is best for retro-curriculum or inventory-clearance lab kits.
Empfohlen
Replacement of Discrete Logic in Legacy Designs
The PIC16LC62B-04/SP is often used as a single-chip replacement for legacy designs built from 74-series TTL/CMOS glue logic, where 22 I/O pins can absorb 10-20 discrete gates, latches, and counter packages. With 3.5 KB OTP and 128-byte RAM it can implement state machines, frequency dividers, debouncers, and timed-sequence controllers in firmware. The 4 MHz clock and 200 ns cycle time are fast enough to emulate 1-2 MHz legacy logic in software. Compared to discrete-logic rebuilds, this part reduces PCB area by 50-70% and BOM count by an order of magnitude.
Empfohlen
Embedded Timing and Sequencing Circuits
The PIC16LC62B-04/SP suits timing and sequencing circuits that previously used 555 timers, CD4541, or discrete RC networks. Its Timer0 (8-bit with prescaler) and Timer1 (16-bit) modules generate programmable delays from microseconds to minutes, and the CCP module produces PWM or compare-match triggers. The 22 I/O lines drive sequencer step relays, indicator LEDs, and interlock chains for industrial timers. Designers use the watchdog timer for failsafe operation and the power-on reset for deterministic startup in mission-timing modules.
Empfohlen
Industrial Control Logic Modules
The PIC16LC62B-04/SP fits industrial control-logic modules where deterministic GPIO state machines replace PLC-style ladder logic for low-cost sub-systems. The 3.3V/5V supply and external-oscillator design accommodate noisy factory environments when paired with optocouplers and TVS protection. Its 22 I/O pins handle digital inputs from limit switches and outputs to relay drivers, with the CCP module generating PWM for proportional valves or indicator dimming. Trade-off: for safety-rated industrial systems (SIL/PL), engineers must add external watchdogs and dual-channel I/O; this OTP MCU alone cannot meet functional-safety standards.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PIC16LC62B-04/SP – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PIC16C62B-04/SP | PIC16LC62B-04/SO | PIC16LC62A-04I/SO | PIC16LC621A-04I/P |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-SPDIP | 28-SPDIP (same) | 28-SOIC (different) | 28-SOIC (different) | 28-PDIP (same row, wider body) |
| Program Memory | 3.5 KB (2K x 14) OTP EPROM | 3.5 KB OTP | 3.5 KB OTP (same die) | 3.5 KB OTP | 1.75 KB OTP |
| Maximum Clock | 4 MHz | 4 MHz | 4 MHz | 4 MHz | 4 MHz |
| RAM Size | 128 bytes | 128 bytes | 128 bytes | 128 bytes | 96 bytes |
| Number of I/O | 22 | 22 | 22 | 22 | 13 |
| Supply Voltage | 3.3V / 5V (LC variant) | 5V only (standard variant) | 3.3V / 5V | 3.3V / 5V | 3.3V / 5V |
| Memory Type | OTP EPROM | OTP EPROM | OTP EPROM | OTP EPROM | OTP EPROM |
Wichtigste Unterscheidungsmerkmale
- Low-voltage 3.3V/5V dual-supply support (vs. PIC16C62B-04/SP)
- 22 programmable I/O pins across three ports (vs. PIC16LC621A-04I/P)
- 3.5 KB OTP memory with 35 single-cycle instructions (vs. PIC16LC620A-04/P)
Designhinweise
Estimated: at 4 MHz clock and 5V supply, the PIC16LC62B typical active current is approximately 2-5 mA depending on peripheral activity. Add a 100 nF decoupling capacitor within 5 mm of the VDD pin and a bulk 10 uF electrolytic on the supply rail. The /MCLR pin requires a 10 kohm pull-up to VDD and a 100 nF capacitor to ground for brown-out protection. Without these components the MCU may enter undefined reset states on power-up.
The 28-SPDIP through-hole package requires 0.1-inch (2.54 mm) pitch through-hole pads and 0.6-0.8 mm drill holes. Keep the oscillator traces (OSC1, OSC2) shorter than 20 mm and route them away from high-current traces to minimize EMI coupling. Add a guard ring around the analog inputs (RA0-RA5) if connecting to analog signals, and place a ground pour beneath the MCU to reduce thermal gradient and provide low-impedance return paths.
Do not confuse the OTP (one-time programmable) PIC16LC62B with Flash-based PIC16F or PIC18F siblings - the OTP variant cannot be erased and re-programmed. Engineers debugging firmware should buy CERDIP windowed packages (PIC16C62B-04/JW) for development. Also note: the analog inputs (RA0-RA5) share pins with digital I/O and require explicit TRIS/ANSEL configuration before ADC reads; leaving them as digital inputs can damage the analog source if driven above VDD.
The external 4 MHz crystal oscillator needs two 15-33 pF load capacitors (typical 22 pF) placed within 5 mm of the OSC1 and OSC2 pins. For higher-noise environments, use a four-pin crystal module with built-in capacitors rather than a discrete two-pin crystal. The CLKOUT output on OSC2 can drive other PIC devices in a master-slave configuration but should be buffered if it drives more than one slave to avoid signal degradation.
Compliance-Informationen
RoHS / REACH compliance and lead-free status were not stated in the provided Verified Web Data; marked unknown. AEC-Q100 is not applicable because this is a general-purpose commercial/industrial MCU not qualified for automotive use.
