PIC16LF1615-I/ST - 8-bit MCU, 32MHz, 14KB Flash 14-TSSOP | Microchip
Teilenummer: PIC16LF1615-I/ST ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $1.65 | $1,65 |
| 10 | $1.48 | $14,80 |
| 100 | $1.32 | $132,00 |
| 500 | $1.18 | $590,00 |
| 1.000 | $1.05 | $1.050,00 |
| 3.000 | $0.95 | $2.850,00 |
PIC16LF1615-I/ST Übersicht
A PIC (Peripheral Interface Controller) microcontroller is an 8-bit RISC-based microprocessor with integrated Flash program memory, RAM, EEPROM, and a rich set of on-chip peripherals. Within the broader taxonomy, the PIC16LF1615 sits as: PIC16F1615 -> 8-bit PIC microcontroller -> PIC microcontroller -> microcontroller -> embedded processor -> semiconductor. The 'LF' prefix indicates the low-voltage / low-power variant, supporting operation down to 1.8V and featuring Microchip's XLP™ (eXtreme Low Power) sleep modes that draw nanoamp-level currents in deep sleep.
Key features include 14KB of self-programmable Flash program memory, 1KB of RAM, hardware peripherals such as 10-bit A/D converter, Capture/Compare/PWM (CCP), 24-bit Signal Measurement Timer (SMT), Zero-Cross Detection, and a complementary waveform generator for motor control. The 'LF' variant supports 1.8V-3.6V operation, making it suited for battery-powered applications. Programming is supported via In-Circuit Serial Programming (ICSP) and high-voltage ICSP, with the industrial temperature grade (-40C to +85C) denoted by the 'I' suffix.
The PIC16LF1615-I/ST architecture is built around a 14-bit instruction word and a Harvard bus architecture with separate program and data paths, enabling single-cycle instruction execution except for branches. On-chip peripherals are interconnected through the Peripheral Pin Select (PPS) system, allowing flexible function remapping. This technical depth makes the device suitable for both general-purpose logic replacement and specialized applications such as motor control loops, where the 24-bit SMT and ZCD peripherals directly address zero-crossing detection and AC line measurement without external components.
Typical applications include small BLDC / brushed DC motor control, ceiling fan controllers, LED lighting drivers, battery-powered IoT sensor nodes, and general-purpose low-power embedded control. The integrated 10-bit ADC and PWM channels allow direct interfacing with sensors and actuators without external signal conditioning. The TSSOP-14 footprint enables space-constrained designs where QFN packages cannot be reworked by hand.
When designing with this device, ensure decoupling: a 100nF ceramic capacitor placed within 3mm of VDD, plus a 4.7uF bulk capacitor on the analog supply rail if ADC accuracy is required. The MCLR reset pin should be tied to VDD through a 10kΩ pull-up resistor with a 100nF cap to ground for reliable in-circuit programming.
This page synthesizes distributor pricing, pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet alone, providing engineers with a complete procurement and design reference.
Drop-in-Alternativen für PIC16LF1615-I/ST – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit PIC16LF1615-I/ST (gleiche Bauform und Footprint) – abweichend in Package, ADC, I/O Pins, Program Memory (Flash), Communication Peripherals.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
PIC16LF1615T-I/ST
✅ Drop-In✓ Auf Lager
$0.93 / Stück
Datenblatt ansehen →PIC16LF1614-I/ST
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
PIC16LF1619-I/ST
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
PIC16LF1554-I/ST
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$0.85 / Stück
Datenblatt ansehen →PIC16LF1574-I/ST
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$0.85 / Stück
Datenblatt ansehen →PIC16LF1615-I/ST Grenzwerte & elektrische Eigenschaften
| Core Architecture | PIC 8-bit RISC (Harvard) |
| Program Memory (Flash) | 14 KB (8K x 14 words) |
| Data SRAM | 1 KB |
| Maximum CPU Frequency | 32 MHz |
| Operating Voltage Range | 1.8 V to 3.6 V |
| Versorgungsspannung | 2.5 V / 3.3 V / 5 V (LF variant supports 1.8 V minimum) |
| I/O Pins | 12 (in 14-pin TSSOP package) |
| ADC | 10-bit |
| Timers | 24-bit SMT, 16-bit CCP, 8-bit TMR0/TMR2 |
| Gehäuse | 14-TSSOP (4.4 mm width) |
| Betriebstemperaturbereich | -40 C to +85 C (Industrial) |
| Montageart | Surface Mount |
| Programming Method | ICSP (In-Circuit Serial Programming) / High-Voltage ICSP |
| Low-Power Features | XLP™ eXtreme Low Power, nanoWatt sleep |
| RoHS-Status | Compliant |
PIC16LF1615-I/ST Pin-Konfiguration
| Pin 1 | VDD — Positive supply voltage |
| Pin 2 | RA5 — GPIO / I/O port A bit 5 |
| Pin 3 | RA4 — GPIO / I/O port A bit 4 |
| Pin 4 | RA3/MCLR — GPIO / Master Clear reset (input) |
| Pin 5 | RC5 — GPIO / I/O port C bit 5 |
| Pin 6 | RC4 — GPIO / I/O port C bit 4 |
| Pin 7 | RC3 — GPIO / I/O port C bit 3 |
| Pin 8 | RC2 — GPIO / I/O port C bit 2 |
| Pin 9 | RC1 — GPIO / I/O port C bit 1 |
| Pin 10 | RC0 — GPIO / I/O port C bit 0 |
| Pin 11 | RA2 — GPIO / I/O port A bit 2 |
| Pin 12 | RA1/ICSPCLK — GPIO / In-Circuit Serial Programming clock |
| Pin 13 | RA0/ICSPDAT — GPIO / In-Circuit Serial Programming data |
| Pin 14 | VSS — Ground reference |
Typische Anwendungen
PIC16LF1615-I/ST ist geeignet für 6 Anwendungs: Small BLDC Motor Control, LED Lighting Drivers, Battery-Powered IoT Sensor Nodes, Ceiling Fan / HVAC Motor Control, General-Purpose Low-Power Embedded Control, Automotive Body Electronics.
Small BLDC Motor Control
The PIC16LF1615-I/ST is ideally suited for small brushless DC motor control applications. Its integrated 24-bit Signal Measurement Timer (SMT), Zero-Cross Detection (ZCD) peripheral, and complementary waveform generator (CWG) directly drive half-bridges without external logic. The 32 MHz CPU clock provides sufficient MIPS to implement sensorless BEMF zero-crossing commutation in firmware, while the 14 KB Flash accommodates sensorless FOC or trapezoidal commutation tables. The 1.8 V minimum supply enables direct Li-ion battery operation in cordless tools and small appliances. The 14-TSSOP package footprint is small enough for integration into motor housings where QFN packages cannot be hand-reworked.
Empfohlen
LED Lighting Drivers
The PIC16LF1615-I/ST drives dimmable LED lighting products where its 10-bit ADC reads ambient light sensors and potentiometers, while the 16-bit CCP module generates PWM dimming signals at frequencies above the audible band (>20 kHz) to eliminate flicker. The XLP™ low-power sleep modes reduce standby consumption below 50 nA, enabling always-on smart lighting fixtures that meet Energy Star and Title 24 standby limits. The 1.8 V minimum supply supports direct Li-ion emergency lighting operation. Integrated Zero-Cross Detection simplifies TRIAC dimmer interface circuitry, eliminating the optocoupler in many reference designs.
Empfohlen
Battery-Powered IoT Sensor Nodes
The PIC16LF1615-I/ST is an excellent choice for battery-powered IoT sensor nodes where its XLP™ technology achieves nanoamp-level sleep currents below 50 nA, enabling multi-year battery life on a single coin cell. The 1.8 V to 3.6 V supply range supports direct operation from one or two alkaline cells, or from a single Li-ion / LiFePO4 cell across its entire discharge curve. The 14 KB Flash accommodates LoRaWAN class A device firmware, BLE beacon stacks, or proprietary sub-GHz protocols. Integrated 10-bit ADC and temperature indicator allow direct sensor reading without external analog front-end, reducing BOM cost for high-volume sensor products.
Empfohlen
Ceiling Fan / HVAC Motor Control
The PIC16LF1615-I/ST controls ceiling fan and HVAC blower motors with closed-loop speed regulation. The 24-bit SMT captures AC line frequency for accurate RPM measurement, while the CWG peripheral generates phase-controlled TRIAC firing pulses for AC motor dimming. The industrial -40C to +85C temperature range supports attic and outdoor HVAC installations. The 14 KB Flash fits full-state BLDC commutation tables with temperature-compensated ramp profiles. Designers benefit from the same TSSOP-14 footprint across multiple SKUs (1614/1615/1618/1619), enabling SKU flexibility without PCB redesign.
Empfohlen
General-Purpose Low-Power Embedded Control
The PIC16LF1615-I/ST is well suited as a general-purpose low-power MCU for embedded control applications where engineers need 8-bit simplicity, mature toolchain support, and long-term Microchip supply commitment. The Peripheral Pin Select (PPS) system allows flexible remapping of digital peripherals to any I/O pin, simplifying PCB layout. The 14 KB Flash and 1 KB RAM are sufficient for state machines, sensor fusion, keypad scanning, and simple user interfaces. Code migration within the PIC16F family is straightforward via MPLAB X IDE, with extensive application libraries and code examples available on Microchip's website.
Empfohlen
Automotive Body Electronics
The PIC16LF1615-I/ST (industrial grade -40C to +85C) is suitable for non-safety automotive body electronics such as interior lighting controllers, seat position sensors, and accessory multiplexers where its 10-bit ADC reads position sensors and the CWG drives small motor loads. Note that this 'I' (industrial) grade variant is NOT AEC-Q100 qualified - for AEC-Q100 Grade 0 or Grade 1 automotive applications, designers should select the PIC16F1615-E/ST (extended) or PIC16F1615-HV automotive variants. The TSSOP-14 footprint allows placement inside tight automotive enclosures where hand-reworkability is required.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PIC16LF1615-I/ST – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PIC16LF1615T-I/ST | PIC16LF1614-I/ST | PIC16LF1554-I/ST | PIC16LF1574-I/ST |
|---|---|---|---|---|---|
| Package | 14-TSSOP | 14-TSSOP - same | 14-TSSOP - same | 14-TSSOP - same | 14-TSSOP - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core Architecture | PIC 8-bit RISC | PIC 8-bit RISC | PIC 8-bit RISC | PIC 8-bit RISC | PIC 8-bit RISC |
| Flash Memory | 14 KB | 14 KB | 8 KB | 7 KB | 7 KB |
| RAM | 1 KB | 1 KB | 1 KB | 256 B | 512 B |
| Max CPU Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Operating Voltage | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V |
| Operating Temperature | -40 C to +85 C (Industrial) | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
| ADC Resolution | 10-bit | 10-bit | 10-bit | 10-bit | 10-bit |
Wichtigste Unterscheidungsmerkmale
- Lowest operating voltage in PIC16F1615 family (vs. PIC16F1615-I/ST)
- Largest Flash in 14-pin TSSOP PIC16F1615 family (vs. PIC16LF1614-I/ST)
- Highest RAM among 14-pin TSSOP PIC16LF15xx alternatives (vs. PIC16LF1554-I/ST)
- Integrated Zero-Cross Detection peripheral (vs. PIC16LF1574-I/ST)
Designhinweise
Place a 100nF ceramic decoupling capacitor within 3 mm of the VDD pin (pin 1) and a 4.7uF to 10uF bulk capacitor near the VDD rail. For ADC accuracy better than 1 LSB, add a separate 100nF cap on the AVdd pin if used. The 'LF' variant operating at 1.8 V requires low-Voltage-dropout (LDO) regulation - MCP1700 is recommended for its 250 mV dropout at 250 mA load, enabling single Li-ion cell operation down to 3.0 V Vbat.
The 14-TSSOP package has a 0.65 mm pin pitch requiring fine-pitch SMT assembly. Use NSMD (Non-Solder Mask Defined) pads with 0.30 mm pad width for reliable solder joints. Stencil apertures should be 0.40 mm wide with 100um thickness for lead-free reflow. Hand-rework is possible with a fine-tip soldering iron (1 mm chisel) but requires flux and careful thermal management to avoid pad lifting.
Do NOT confuse the 'LF' (1.8 V to 3.6 V) variant with the 'F' variant (2.5 V to 5.5 V) - they share the same pinout but different electrical characteristics. Programming voltage thresholds differ; using the wrong datasheet parameters will cause read failures or programming errors. Always verify the exact ordering code (PIC16LF1615 vs PIC16F1615) before PCB assembly. The MCLR pin (pin 4) requires a 10kΩ pull-up to VDD for normal operation; leaving it floating causes unpredictable reset behavior.
Compliance-Informationen
Industrial temperature grade -40C to +85C. Not AEC-Q100 qualified - choose automotive PIC16F1615 variants for vehicular applications. RoHS and REACH compliant per Microchip product declaration.
