PIC16LF1713-I/SS - 8-bit 32MHz MCU 7KB Flash 28-SSOP | Microchip
Teilenummer: PIC16LF1713-I/SS ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $2.21 | $2,21 |
| 10 | $2.02 | $20,20 |
| 100 | $1.85 | $185,00 |
| 500 | $1.68 | $840,00 |
| 1.000 | $1.52 | $1.520,00 |
| 3.000 | $1.38 | $4.140,00 |
PIC16LF1713-I/SS Übersicht
Key specifications include an integrated 10-bit ADC, on-chip op amps (up to two), 5-bit and 8-bit DACs, Core Independent Peripherals (CLC, NCO, COG), Peripheral Pin Select (PPS), Zero-Cross Detect, EUSART, I2C/SPI, and CCP/PWM modules. Operating voltage spans 1.8V to 3.6V with a wide -40C to +85C industrial temperature range, and XLP technology delivers sub-microamp sleep currents for battery-powered applications.
The PIC16LF1713 combines an enhanced mid-range PIC16 CPU core with intelligent analog, allowing designers to replace external op-amps, comparators, and signal-conditioning circuitry with on-chip resources. The 28-pin SSOP package exposes up to 25 I/O pins, with PPS allowing peripheral function remapping to nearly any pin to simplify PCB layout and BOM consolidation. The 7KB FLASH supports 4K single-word instructions and 100,000 erase/write cycles typical endurance.
Typical applications include IoT sensor nodes, battery-powered handheld instruments, LED lighting controllers, white goods and appliance control, low-cost motor control, and general-purpose embedded logic. The XLP feature set makes it especially compelling for energy-harvesting or coin-cell applications where sleep current dominates battery life. Design considerations include mandatory use of an ICD or PICkit programmer for debug, careful PPS configuration to avoid peripheral conflicts, and adherence to the 1.8V minimum VDD at full 32MHz operation per the Microchip datasheet.
Drop-in-Alternativen für PIC16LF1713-I/SS – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit PIC16LF1713-I/SS (gleiche Bauform und Footprint) – abweichend in Core Architecture, Core Independent Peripherals, Package, ADC, Family.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
PIC16LF1716-I/SS
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC16F1713-I/SS
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC16LF1713T-I/SS
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC16LF1713-I/SP
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
PIC16LF1713-E/SS
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
PIC16LF1713-I/SS Grenzwerte & elektrische Eigenschaften
| Family | PIC® XLP™ 16F |
| Core Architecture | 8-bit PIC16 enhanced mid-range |
| CPU Speed (Max) | 32 MHz |
| Program Memory (FLASH) | 7 KB (4K x 14 words) |
| Data RAM | 512 bytes |
| Operating Voltage (VDD) | 1.8 V to 3.6 V |
| Betriebstemperatur | -40 C to +85 C (Industrial) |
| ADC | 10-bit |
| DAC | 5-bit / 8-bit |
| On-Chip Op Amps | Up to 2 |
| Comparators | Yes |
| PWM Channels (CCP) | Yes |
| Communication | EUSART, I2C, SPI |
| Peripheral Pin Select (PPS) | Yes |
| Core Independent Peripherals | CLC, NCO, COG, Zero-Cross Detect |
| Gehäuse | 28-pin SSOP (5.30 mm) |
| Montageart | Surface Mount |
| MSL-Level | 1 (per Microchip standard) |
| RoHS-Status | Compliant |
| Low-Power Feature | XLP (eXtreme Low Power) |
PIC16LF1713-I/SS 28-pin ssop (5.30 mm) Pinbelegungsleitfaden
Pinbelegung für PIC16LF1713-I/SS (28-pin ssop (5.30 mm)-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für PIC16LF1713-I/SS.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
PIC16LF1713-I/SS ist geeignet für 6 Anwendungs: Battery-Powered IoT Sensor Nodes, LED Lighting Controllers, White Goods and Appliance Control, Low-Cost Motor Control (BLDC / Stepper), Energy-Harvesting and Remote Sensing, General-Purpose Embedded Logic Replacement.
Battery-Powered IoT Sensor Nodes
The PIC16LF1713-I/SS fits battery-powered IoT sensor nodes by combining its XLP sleep-current technology with 1.8V minimum VDD and integrated 10-bit ADC plus on-chip op amps. With sub-microamp sleep currents and active wake from the ADC, comparators, or Zero-Cross Detect, the device can run for years on a coin cell when duty-cycled. The 7KB FLASH accommodates typical BLE/Zigbee host state-machine code, and 512B RAM suffices for sensor buffering. PPS allows the EUSART, I2C, or SPI to map to nearly any pin, simplifying board layout with mixed sensor types. The 28-SSOP package is surface-mount friendly and the small footprint supports compact wearable or remote-sensor enclosures.
Empfohlen
LED Lighting Controllers
The PIC16LF1713-I/SS is well-suited for LED lighting controllers where its integrated 10-bit ADC reads light sensors, the on-chip op amps condition thermistor inputs for thermal foldback, and the 5/8-bit DAC sets dimming levels. The PWM/CCP modules drive LED MOSFET drivers with fine resolution, while CLC (Configurable Logic Cell) implements hardware-only fade logic without CPU intervention. Zero-Cross Detect synchronizes TRIAC dimming to AC line frequency, and PPS keeps the PCB layout flexible. Operating from 1.8V to 3.6V supports both 3.3V and battery-backed emergency-lighting designs.
Empfohlen
White Goods and Appliance Control
The PIC16LF1713-I/SS is a strong fit for white goods and appliance control boards where it drives user-interface keypads, reads NTC thermistors via the 10-bit ADC, and controls motor or valve actuators via PWM/CCP. The on-chip comparators handle over-current and over-temperature protection with hardware response time independent of CPU latency. EUSART and I2C connect to display modules, sensor hubs, or main controller boards; SPI drives external EEPROM for parameter storage. The industrial -40C to +85C operating range and 3.6V max VDD suit 3.3V appliance rails.
Empfohlen
Low-Cost Motor Control (BLDC / Stepper)
The PIC16LF1713-I/SS handles low-cost BLDC and stepper motor control applications by leveraging its PWM/CCP channels, on-chip op amps for current sensing, and the NCO (Numerically Controlled Oscillator) for precise commutation timing. The 32 MHz CPU executes simple FOC or 6-step commutation algorithms within 7KB FLASH. Zero-Cross Detect simplifies back-EMF sensing for sensorless BLDC, while PPS allows the comparator outputs to drive FET predrivers directly. The wide 1.8-3.6V supply range is friendly to low-voltage motor driver ICs, and 512B RAM suffices for real-time state machines.
Empfohlen
Energy-Harvesting and Remote Sensing
The PIC16LF1713-I/SS fits energy-harvesting and remote-sensing designs where its XLP technology enables operation from harvested micro-power sources. The 1.8V minimum VDD matches typical solar-cell or thermal-harvester open-circuit voltages, and the sub-microamp sleep current allows indefinite standby between energy accumulation cycles. The 10-bit ADC with integrated op amps reads low-level sensor signals without external amplification. CLC and NCO implement event-driven logic that wakes the CPU only when a meaningful signal event occurs, further reducing average power consumption in field deployments.
Empfohlen
General-Purpose Embedded Logic Replacement
The PIC16LF1713-I/SS replaces discrete logic and glue circuitry in cost-sensitive embedded systems by consolidating timing, serial communication, signal conditioning, and decision logic on a single 28-pin MCU. Its Peripheral Pin Select allows pin assignment flexibility, making PCB re-spins simpler when I/O requirements change. With 7KB FLASH and 512B RAM, it comfortably fits typical protocol-translation, supervisory, or polling-and-response state machines used in industrial sensor hubs, automotive body modules, or consumer peripherals. The wide 1.8-3.6V range and industrial temperature grade suit harsh environments.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PIC16LF1713-I/SS – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PIC16LF1716-I/SS | PIC16F1713-I/SS | PIC16LF1713T-I/SS |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-SSOP | 28-SSOP (same) | 28-SSOP (same) | 28-SSOP (same) |
| FLASH | 7 KB | 7 KB | 7 KB | 7 KB |
| RAM | 512 B | 512 B | 512 B | 512 B |
| Operating Voltage | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 2.3 V to 5.5 V (different) | 1.8 V to 3.6 V |
| CPU Speed (Max) | 32 MHz / 8 MIPS | 32 MHz / 8 MIPS | 32 MHz / 8 MIPS | 32 MHz / 8 MIPS |
| ADC | 10-bit | 10-bit | 10-bit | 10-bit |
| On-Chip Op Amps | Up to 2 | Up to 2 | Up to 2 | Up to 2 |
| Operating Temperature | -40 C to +85 C (Industrial) | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
| XLP Low-Power | Yes | Yes | Yes | Yes |
Wichtigste Unterscheidungsmerkmale
- Intelligent Analog integration with on-chip op amps (vs. PIC16LF1709-I/P)
- Wide low-voltage operating range for battery designs (vs. PIC16F1713-I/SS)
- Core Independent Peripherals reduce CPU load (vs. PIC16LF1574-I/P)
Designhinweise
Estimated: at VDD=3.3V, 32MHz CPU active, the PIC16LF1713-I/SS typically draws ~3-4 mA active. With XLP sleep mode enabled (peripherals off, CPU off, RTCC running), sleep current drops to sub-microamp levels. For battery-life calculations, average active duty cycle current with sleep current; for a 1% duty cycle and 4mA active / 1uA sleep, average current is approximately 41 uA - suitable for multi-year coin-cell operation. Always consult the PIC16(L)F1713/6 datasheet for the latest typical current numbers.
Do not confuse the PIC16LF1713 (1.8-3.6V 'LF' variant) with the PIC16F1713 (2.3-5.5V standard variant). Both share pinout and part number suffix but require different VDD designs. Also ensure the ICSP programming pins (typically PGC/PGD on dedicated or shared I/O) are accessible on the PCB for in-circuit programming; PPS remapping during development can prevent post-programming verification if the debugger cannot access the configured pins.
Place a 0.1 uF decoupling capacitor as close as possible to the VDD pin, with a 1 uF bulk capacitor on the same rail for transient handling. The analog AVSS/AVDD pins (if separate) require their own decoupling network. For SSOP-28 packages, ensure adequate copper area for thermal dissipation - though the PIC16LF1713-I/SS typically dissipates <100 mW, copper pour improves long-term reliability.
Compliance-Informationen
RoHS and REACH compliant per Microchip product page. Industrial temperature grade -40C to +85C; not AEC-Q100 qualified (automotive variants available in the PIC16 family as separate MPNs). Lead-free and halogen-free per Microchip standard packaging.
