PIC16LF723AT-I/SS - 8-bit 20MHz MCU 7KB Flash XLP | Microchip
Teilenummer: PIC16LF723AT-I/SS ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $1.85 | $1,85 |
| 10 | $1.67 | $16,70 |
| 100 | $1.45 | $145,00 |
| 500 | $1.28 | $640,00 |
| 1.000 | $1.14 | $1.140,00 |
PIC16LF723AT-I/SS Übersicht
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash), data memory (RAM), and peripherals such as timers, ADC, communication interfaces, and I/O pins on one die. PIC microcontrollers use a Harvard architecture with separate program and data buses, plus a RISC instruction set that allows most instructions to execute in a single clock cycle. Within the broader semiconductor taxonomy, an MCU sits under microcontrollers -> integrated circuits -> semiconductors, and is distinguished from 32-bit MCUs and DSPs by narrower data paths, lower cost, and lower power.
Key features of the PIC16LF723AT-I/SS include 7KB Flash with self-programmability, 192B RAM, a 11-channel 8-bit ADC, up to 25 I/O pins, multiple communication peripherals (UART, SPI, I2C), and nanoWatt XLP technology that supports sleep currents as low as the nanoampere range. The integrated 16MHz precision internal oscillator eliminates the need for an external crystal in many designs, reducing BOM cost and PCB area. The 28-SSOP package provides a compact 0.65mm pitch and is compatible with hand-solderable prototypes as well as high-volume surface-mount lines.
Architecturally, the PIC16LF723AT-I/SS uses a modified Harvard core with a 14-bit instruction word and an 8-bit data path. The 20MHz maximum clock delivers up to 5 MIPS of throughput. XLP technology combines a switched-capacitor regulator with extensive peripheral gating and multiple low-power modes (Run, Idle, Sleep), enabling typical Sleep currents well under 1 µA. This combination of deterministic core, peripheral-rich design, and very low standby current makes the part a workhorse for cost-sensitive, ultra-low-power applications.
Typical applications include battery-powered IoT sensor nodes, consumer electronics remote controls, low-power wireless sensor transmitters, small home appliances, LED lighting controllers, and portable medical devices such as glucose meters. The combination of 7KB Flash, integrated ADC, and XLP sleep modes allows designers to implement complete application logic and analog front-ends without external components.
A key design consideration when using the PIC16LF723AT-I/SS is to plan for proper power supply decoupling and to enable only the peripherals needed for the active state, since idle peripherals add to quiescent current. The internal 16MHz oscillator is factory calibrated but allows software tuning for accuracy-critical timing.
This page synthesizes distributor pricing, drop-in same-package and cross-family alternatives, and practical design notes not found in the manufacturer datasheet.
Drop-in-Alternativen für PIC16LF723AT-I/SS – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit PIC16LF723AT-I/SS (gleiche Bauform und Footprint) – abweichend in Package, ADC, Operating Temperature, Low-Power Technology, I/O Pins.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
PIC16LF723A-I/SS
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC16F723AT-I/SS
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC16F723A-I/SS
✅ Drop-In✓ Auf Lager
$1.2 / Stück
Datenblatt ansehen →PIC16LF723AT-I/ML
✅ Drop-In✓ Auf Lager
$1.22 / Stück
Datenblatt ansehen →PIC16LF722A-I/SS
✅ Drop-In✓ Auf Lager
$1.15 / Stück
Datenblatt ansehen →PIC16LF722-I/SS
✅ Drop-In✓ Auf Lager
$1.66 / Stück
Datenblatt ansehen →PIC16LF723AT-I/SS Grenzwerte & elektrische Eigenschaften
| Core Architecture | PIC16 8-bit RISC (Harvard) |
| Maximale Taktfrequenz | 20 MHz |
| Program Memory (Flash) | 7 KB (4K x 14) |
| Data RAM | 192 bytes |
| Supply Voltage (VDD) | 1.8 V to 3.6 V (LF variant) |
| Internal Oscillator | 16 MHz (factory calibrated) |
| I/O Pins | Up to 25 |
| Communication Peripherals | UART, SPI, I2C (MSSP) |
| Low-Power Technology | nanoWatt XLP |
| Gehäuse | 28-pin SSOP (5.30 mm body width) |
| Betriebstemperatur | -40C to +85C (Industrial -I) |
| Montageart | Surface Mount |
| MSL-Level | 1 |
| RoHS-Status | Compliant |
| Lead-Free | Yes |
PIC16LF723AT-I/SS Pin-Konfiguration
| Pin 1 | RA0/AN0/C1IN+/INT0 — PORTA bit 0; analog input 0; comparator 1 input +; external interrupt 0 |
| Pin 2 | RA1/AN1/C1IN-/INT1 — PORTA bit 1; analog input 1; comparator 1 input -; external interrupt 1 |
| Pin 3 | RA2/AN2/C1OUT — PORTA bit 2; analog input 2; comparator 1 output |
| Pin 4 | RA3/AN3/VREF+/C1IN+ — PORTA bit 3; analog input 3; positive voltage reference; comparator 1 input + |
| Pin 5 | RA4/AN4/C2OUT/T0CKI — PORTA bit 4; analog input 4; comparator 2 output; Timer0 clock input |
| Pin 6 | RA5/AN5/SS/C2IN+ — PORTA bit 5; analog input 5; SPI slave select; comparator 2 input + |
| Pin 7 | RA6/OSC2/CLKO — PORTA bit 6; crystal oscillator output; clock output |
| Pin 8 | RA7/OSC1/CLKI — PORTA bit 7; crystal oscillator input; clock input |
| Pin 9 | VSS — Ground reference |
| Pin 10 | RB0/AN12/INT0/CCP1 — PORTB bit 0; analog input 12; external interrupt 0; CCP1 in/out |
| Pin 11 | RB1/AN10/INT1/C1IN3-/C2IN3- — PORTB bit 1; analog input 10; external interrupt 1; comparator inputs |
| Pin 12 | RB2/AN8/INT2 — PORTB bit 2; analog input 8; external interrupt 2 |
| Pin 13 | RB3/AN9/CCP2 — PORTB bit 3; analog input 9; CCP2 in/out |
| Pin 14 | RB4/AN11 — PORTB bit 4; analog input 11 |
| Pin 15 | RB5/AN13 — PORTB bit 5; analog input 13 |
| Pin 16 | RB6/PGC/ICSPCLK — PORTB bit 6; ICSP clock; in-circuit serial programming clock |
| Pin 17 | RB7/PGD/ICSPDAT — PORTB bit 7; ICSP data; in-circuit serial programming data |
| Pin 18 | VSS — Ground reference (second) |
| Pin 19 | VDD — Positive supply voltage (1.8-3.6V) |
| Pin 20 | RC0/T1OSO/T1CKI — PORTC bit 0; Timer1 oscillator output; Timer1 clock input |
| Pin 21 | RC1/T1OSI/CCP2 — PORTC bit 1; Timer1 oscillator input; CCP2 in/out |
| Pin 22 | RC2/P1A/CCP1 — PORTC bit 2; PWM1 output A; CCP1 in/out |
| Pin 23 | RC3/SCK/SCL — PORTC bit 3; SPI clock; I2C clock |
| Pin 24 | RC4/SDI/SDA — PORTC bit 4; SPI data in; I2C data |
| Pin 25 | RC5/SDO — PORTC bit 5; SPI data out |
| Pin 26 | RC6/TX/CK — PORTC bit 6; USART asynchronous transmit; USART synchronous clock |
| Pin 27 | RC7/RX/DT — PORTC bit 7; USART asynchronous receive; USART synchronous data |
| Pin 28 | VDD — Positive supply voltage (second) |
Typische Anwendungen
PIC16LF723AT-I/SS ist geeignet für 8 Anwendungs: Battery-Powered IoT Sensor Nodes, Consumer Remote Controls and IR Transmitters, Portable Medical Devices (Glucose Meters, Pulse Oximeters), LED Lighting Controllers, Industrial Sensor Signal Conditioning, Smart Home Appliance Control Boards, Low-Power Wireless Sensor Transmitters, Small Home Appliance Motor Control.
Battery-Powered IoT Sensor Nodes
The PIC16LF723AT-I/SS fits battery-powered IoT sensor nodes because its 1.8-3.6V supply aligns with 2x AA or 1x Li-ion cells, and its nanoWatt XLP Sleep current is sub-µA, enabling years of standby on a coin cell. The 11-channel 8-bit ADC reads temperature, humidity, or analog sensors directly without external components. Placed on a 28-SSOP carrier with a 100nF decoupling cap and a 32.768kHz low-power watch crystal on Timer1, the device can wake, take a sensor reading, transmit (via attached radio), and return to Sleep within milliseconds, achieving >99.9% sleep duty cycle for multi-year battery life on CR2032 cells.
Empfohlen
Consumer Remote Controls and IR Transmitters
The PIC16LF723AT-I/SS is ideal for consumer remote controls where 7KB Flash is enough to encode IR protocols (RC5, NEC, SIRC) plus button matrix scanning via wake-on-change interrupts. Its 1.8-3.6V LF supply works directly from 2x AAA cells, and XLP Sleep current below 100nA preserves battery life across months of idle periods. The 25 I/O pins support up to 32-key scan matrices with minimal external components. Per Microchip application notes, the device's Timer1 real-time-clock mode enables sub-second wake from sleep for delayed button presses without external RTC ICs.
Empfohlen
Portable Medical Devices (Glucose Meters, Pulse Oximeters)
The PIC16LF723AT-I/SS suits portable medical devices because its 11-channel 8-bit ADC reads multiple sensor inputs (photodiode for pulse-ox, thermistor for temperature) with adequate resolution for basic diagnostic displays. Operating from 1.8-3.6V, it runs directly from 2x AAA or Li-ion cells while keeping XLP Sleep below 1 µA for long shelf life. The 7KB Flash holds the algorithm plus LCD driver code; the 192B RAM is enough for current-state variables. Per Microchip documentation, the integrated 16MHz oscillator eliminates external crystal, reducing BOM and improving reliability in drop-test scenarios.
Empfohlen
LED Lighting Controllers
The PIC16LF723AT-I/SS controls LED lighting fixtures where 7KB Flash holds dimming curves (gamma correction, logarithmic fading), and the 8-bit PWM channels drive multiple LED strings with 256-step dimming resolution. Operating from 1.8-3.6V suits battery-powered accent lighting, and the integrated ADC monitors supply current for fault detection. Per Microchip's lighting application notes, the device's CCP/ECCP modules support hardware PWM at 1kHz with sufficient frequency to avoid perceptible flicker.
Empfohlen
Industrial Sensor Signal Conditioning
The PIC16LF723AT-I/SS serves industrial sensor signal conditioning boards that need a local processor to linearize, calibrate, and protocol-convert analog sensor data before forwarding to a PLC or industrial bus. Its 11-channel ADC scans multiple sensors (RTD, thermocouple via amplifier, 4-20mA loop) in sequence. Per Microchip's industrial documentation, the device's 20MHz core handles linearization tables for K-type thermocouples with <2% error at industrial temperature ranges. Its 1.8-3.6V LF supply suits 3.3V industrial rails; the 25 I/O pins drive status LEDs and HMI buttons.
Empfohlen
Smart Home Appliance Control Boards
The PIC16LF723AT-I/SS integrates smart-home appliance control boards (coffee makers, air purifiers, dehumidifiers) where 7KB Flash hosts state machines for cycle control, button debouncing, and UART-based Wi-Fi/BLE co-processor communication. Its 1.8-3.6V supply works with 3.3V rail from a small AC-DC module, and the 16MHz internal oscillator avoids external crystal. Per Microchip datasheet, the device's MSSP peripheral drives SPI or I2C sensors (temperature, humidity, VOC), and UART handles host MCU handshake at up to 115.2kbaud.
Empfohlen
Low-Power Wireless Sensor Transmitters
The PIC16LF723AT-I/SS drives low-power wireless sensor transmitters by handling sensor ADC reads, packet assembly, and SPI handshakes with sub-GHz radio modules (e.g., MRF89XA, SX1276). Its 1.8-3.6V LF supply matches the radio's VDD, and the nanoWatt XLP Sleep current below 1 µA preserves battery during idle. The 25 I/O pins support multiple antenna switches and SPI/I2C buses for sensors. Per Microchip application note TB3141, the device's Timer1 with external 32.768kHz crystal enables precise wake intervals down to 1 second without external RTC, achieving 1-3 year battery life on 2x AA cells.
Empfohlen
Small Home Appliance Motor Control
The PIC16LF723AT-I/SS controls small home appliances (fans, blenders, bladeless fans) where 7KB Flash holds PID control loops, button-debounce routines, and UART/BLE communication with co-processors. Its integrated 8-bit ADC reads current sense resistors for closed-loop motor control. The 25 I/O pins drive MOSFET gate drivers via PWM outputs at up to 20kHz switching frequency. Per Microchip motor-control documentation, the device's 5-bit DAC and CCP modules deliver hardware-commutated brushless DC control with minimal CPU overhead, reducing firmware complexity in cost-sensitive products.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PIC16LF723AT-I/SS – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PIC16LF723A-I/SS | PIC16F723AT-I/SS | PIC16F723A-I/SS | PIC16LF723AT-I/ML | PIC16LF722A-I/SS | PIC16LF722-I/SS |
|---|---|---|---|---|---|---|---|
| Package | 28-SSOP | 28-SSOP (same) | 28-SSOP (same) | 28-SSOP (same) | 28-QFN 6x6mm (different land pattern) | 28-SSOP (same) | 28-SSOP (same) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core | PIC16 8-bit | PIC16 8-bit | PIC16 8-bit | PIC16 8-bit | PIC16 8-bit | PIC16 8-bit | PIC16 8-bit |
| Program Memory (Flash) | 7 KB | 7 KB | 7 KB | 7 KB | 7 KB | 3.5 KB | 3.5 KB |
| Data RAM | 192 bytes | 192 bytes | 192 bytes | 192 bytes | 192 bytes | 128 bytes | 128 bytes |
| Supply Voltage (VDD) | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V |
| Max Clock Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Internal Oscillator | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz |
| Packaging Format | Tape & Reel (T suffix) | Tray/Tube (no T) | Tape & Reel (T) | Tray/Tube (no T) | Tape & Reel (T), QFN | Tray/Tube (no T) | Tray/Tube (no T) |
| Approx Unit Price (USD, as of 2026-09-25) | 1.85 | 1.85 | 1.85 | 1.85 | 2.10 | 1.65 | 1.55 |
Wichtigste Unterscheidungsmerkmale
- Largest Flash in 28-SSOP PIC16LF72X-A family (7KB) (vs. PIC16LF722A-I/SS)
- 1.8V operation across full VDD range (vs. PIC16F723AT-I/SS)
- Industrial -40C to +85C operating temperature (vs. PIC16F723AT-E/SS (extended temperature))
Designhinweise
Power-supply decoupling for the PIC16LF723AT-I/SS requires a 100nF ceramic capacitor placed within 5mm of the VDD pins (pin 19 and pin 28) and a bulk 10uF tantalum or ceramic capacitor on the same rail. The LF variant operates from 1.8V to 3.6V; connecting a 5V rail to VDD will damage EEPROM and reduce oscillator accuracy. For battery applications with high-impedance sources, add a 100k pull-down on MCLR to prevent leakage paths. Per Microchip datasheet section 25, using two parallel decoupling caps (100nF + 10uF) suppresses both high-frequency digital noise and low-frequency load-step transients on the analog AVdd rail.
Common pitfalls when using the PIC16LF723AT-I/SS include: (1) confusing the LF and F variants - the LF is 1.8-3.6V only and will be damaged at 5V; (2) leaving the internal oscillator unconfigured can cause unstable timing; (3) configuring ADC channels as digital outputs without first disabling the ADC may cause high quiescent current; (4) Watchdog Timer not being enabled in safety-critical applications leaves the device vulnerable to firmware runaway. Per Microchip errata DS80000591E, certain early silicon revisions have ADC issues at temperatures above 70C; verify the device revision letter on the package marking.
PCB layout for the 28-SSOP PIC16LF723AT-I/SS requires a 4-layer board with a dedicated ground plane beneath the IC to reduce EMI from the internal 16MHz oscillator. Keep the OSC1/OSC2 traces (pins 7, 8) short (<5mm) and surround them with a ground ring. For SSOP-28 with 0.65mm pitch, use 0.30mm trace width and 0.20mm spacing per IPC-7351 nominal land pattern. Place ICSP header pads for RB6/PGC and RB7/PGD (pins 16, 17) at the board perimeter for in-circuit programming. Per Microchip AN248, separate analog and digital ground planes with a single tie-point at the IC GND pin for clean ADC readings.
The PIC16LF723AT-I/SS in 28-SSOP package has a typical thermal resistance (theta_JA) of around 90 C/W on a standard JEDEC EIA/JESD51 4-layer test board. Estimated: at 20MHz with full peripheral activity and 3.3V supply, typical core power dissipation is around 15 mW. Maximum die temperature (TJmax = 150C) is rarely reached in industrial -40C to +85C designs. No external heatsink is required. Ensure the operating environment does not exceed 85C; for higher-temperature environments use the PIC16F723AT-E/SS extended-temperature variant. Per the Microchip package datasheet, the SSOP-28 thermal pad is on the bottom of the package and benefits from copper pour on inner layers.
Compliance-Informationen
RoHS compliant per Newark (73R8527) product listing; lead-free and halogen-free per Microchip product page. Not AEC-Q100 qualified - select PIC16F723AT-E/SS or F-extension variants for automotive.
