PIC16LF877A-I/L - 8-Bit 10MHz MCU, 14KB Flash, 44-PLCC | Microchip
Teilenummer: PIC16LF877A-I/L ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $6.96 | $6,96 |
| 10 | $6.26 | $62,60 |
| 100 | $5.61 | $561,00 |
| 500 | $4.96 | $2.480,00 |
| 1.000 | $4.31 | $4.310,00 |
PIC16LF877A-I/L Übersicht
An 8-bit PIC microcontroller is a Harvard-architecture RISC device that executes one instruction every clock cycle, with separate program and data buses that allow simultaneous instruction fetch and operand access. Within the broader taxonomy, the PIC16LF877A is part of the PIC16 mid-range family, which itself sits under Microchip's 8-bit PIC portfolio (PIC10/12/14/16/18), bridging simple 6/8-pin baseline parts and the higher-performance PIC18 series. The "LF" prefix indicates the extended low-voltage design, allowing operation down to 2.5V for battery and energy-efficient designs, while the "A" suffix denotes the enhanced Flash core with the self-programmable, ICD-capable silicon revision.
Key differentiating features include 368 bytes of RAM, 256 bytes of EEPROM data memory, In-Circuit Serial Programming (ICSP) and In-Circuit Debugger (ICD) support, two 8-bit timers plus one 16-bit timer with 3 CCP modules in earlier silicon revisions, 8 channels of 10-bit A/D conversion, a parallel slave port, and a programmable brown-out reset. The PIC instruction set is only 35 single-word instructions, and the core is upwardly source-compatible with the PIC12CXXX, PIC16C5X, and PIC16C7X device families, simplifying migration.
Architecturally, the PIC16LF877A combines a RISC engine with 14-bit wide instructions, a deep 8-level hardware stack, and on-chip Flash permitting self-programming in field. The integrated peripherals are addressable via banked SFRs and support DMA-style auto-increment addressing for ADC bursts, while the USART provides hardware-driven asynchronous framing for RS-232/RS-485 links without CPU overhead. The 44-PLCC variant is socketable, simplifying field service and rework versus QFP or QFN equivalents.
Typical applications include industrial automation controllers, sensor and instrumentation front-ends, HVAC control boards, automotive body and interior ECUs, embedded data-acquisition front ends, and consumer appliance control panels. Its combination of analog integration and broad peripheral mix makes it a strong fit for any sensor-rich, battery-tolerant node requiring moderate compute.
When designing with this part, plan for a single 2.5V to 5.5V rail and ensure your programmer supports ICSP on the working PCB, since field firmware updates typically use this pathway. Decoupling should include a 100 nF ceramic at VDD and a bulk tantalum or aluminum on AVDD, and unused analog inputs must be tied to VSS to minimize ADC shoot-through current.
This page consolidates distributor pricing, drop-in same-package alternatives, application circuit references, and parametric comparison data not assembled on any single manufacturer or distributor page.
Drop-in-Alternativen für PIC16LF877A-I/L – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit PIC16LF877A-I/L (gleiche Bauform und Footprint) – abweichend in Package, Mounting Type, Core Architecture, Program Memory Size, Timers.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
PIC16F877A-I/L
✅ Drop-In✓ Auf Lager
$7.12 / Stück
Datenblatt ansehen →PIC16LF874A-I/L
✅ Drop-In✓ Auf Lager
$6.1 / Stück
Datenblatt ansehen →PIC16F877AT-I/L
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$3.4451 / Stück
Datenblatt ansehen →PIC16LF877A-I/PT
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$4.88 / Stück
Datenblatt ansehen →PIC16LF877AT-I/PT
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$5.95 / Stück
Datenblatt ansehen →PIC16LF877A-I/L Grenzwerte & elektrische Eigenschaften
| Core Architecture | PIC16 8-bit RISC |
| Program Memory | 14 KB (8K x 14) Flash |
| RAM | 368 bytes |
| EEPROM | 256 bytes |
| Maximum CPU Frequency | 10 MHz |
| Instruction Set Size | 35 instructions |
| I/O Pins | 33 |
| ADC | 10-bit, 8 channels |
| Analog Comparators | 2 |
| CCP Modules | 2 |
| Timers | 3 (2x 8-bit, 1x 16-bit) |
| Serial Interfaces | USART/SCI, SPI, I2C |
| Operating Voltage | 2.5 V to 5.5 V |
| Betriebstemperatur | -40 C to +85 C (industrial) |
| Gehäuse | 44-pin PLCC (16.59x16.59 mm) |
| Montageart | Surface Mount (socketable) |
| Programming/Debug | ICSP and ICD support |
PIC16LF877A-I/L Pin-Konfiguration
| Pin 1 | MCLR/VPP — Master clear reset or programming voltage input |
| Pin 2 | RA0/AN0 — Digital I/O or analog input channel 0 |
| Pin 3 | RA1/AN1 — Digital I/O or analog input channel 1 |
| Pin 4 | RA2/AN2/VREF- — Digital I/O, analog channel 2, or A/D reference low |
| Pin 5 | RA3/AN3/VREF+ — Digital I/O, analog channel 3, or A/D reference high |
| Pin 6 | RA4/T0CKI — Digital I/O or Timer0 clock input |
| Pin 7 | RA5/AN4/SS — Digital I/O, analog channel 4, or SPI slave select |
| Pin 8 | RE0/RD/AN5 — Digital I/O, parallel slave port read, or analog channel 5 |
| Pin 9 | RE1/WR/AN6 — Digital I/O, parallel slave port write, or analog channel 6 |
| Pin 10 | RE2/CS/AN7 — Digital I/O, parallel slave port chip select, or analog channel 7 |
| Pin 11 | VDD — Positive supply voltage |
| Pin 12 | VSS — Ground reference |
| Pin 13 | OSC1/CLKIN — Crystal oscillator input or external clock input |
| Pin 14 | OSC2/CLKOUT — Crystal oscillator output or clock output |
| Pin 15 | RC0/T1OSO/T1CKI — Digital I/O, Timer1 oscillator output, or Timer1 clock input |
| Pin 16 | RC1/T1OSI/CCP2 — Digital I/O, Timer1 oscillator input, or CCP2 |
| Pin 17 | RC2/CCP1 — Digital I/O or CCP1 |
| Pin 18 | RC3/SCK/SCL — Digital I/O, SPI clock, or I2C clock |
| Pin 19 | RD0/PSP0 — Digital I/O or parallel slave port bit 0 |
| Pin 20 | RD1/PSP1 — Digital I/O or parallel slave port bit 1 |
| Pin 21 | RD2/PSP2 — Digital I/O or parallel slave port bit 2 |
| Pin 22 | RD3/PSP3 — Digital I/O or parallel slave port bit 3 |
| Pin 23 | RC4/SDI/SDA — Digital I/O, SPI data in, or I2C data |
| Pin 24 | RC5/SDO — Digital I/O or SPI data out |
| Pin 25 | RC6/TX/CK — Digital I/O, USART TX, or USART clock |
| Pin 26 | RC7/RX/DT — Digital I/O, USART RX, or USART data |
| Pin 27 | RD4/PSP4 — Digital I/O or parallel slave port bit 4 |
| Pin 28 | RD5/PSP5 — Digital I/O or parallel slave port bit 5 |
| Pin 29 | RD6/PSP6 — Digital I/O or parallel slave port bit 6 |
| Pin 30 | RD7/PSP7 — Digital I/O or parallel slave port bit 7 |
| Pin 31 | VSS — Ground reference |
| Pin 32 | VDD — Positive supply voltage |
| Pin 33 | RB0/INT — Digital I/O or external interrupt |
| Pin 34 | RB1 — Digital I/O |
| Pin 35 | RB2 — Digital I/O |
| Pin 36 | RB3/PGM — Digital I/O or LVP programming |
| Pin 37 | RB4 — Digital I/O with change-on-interrupt |
| Pin 38 | RB5 — Digital I/O with change-on-interrupt |
| Pin 39 | RB6/PGC — Digital I/O or ICSP clock |
| Pin 40 | RB7/PGD — Digital I/O or ICSP data |
| Pin 41 | NC — Not connected (per datasheet) |
| Pin 42 | NC — Not connected (per datasheet) |
| Pin 43 | NC — Not connected (per datasheet) |
| Pin 44 | NC — Not connected (per datasheet) |
Typische Anwendungen
PIC16LF877A-I/L ist geeignet für 6 Anwendungs: Industrial Automation Controllers, HVAC Control Boards, Automotive Body and Interior ECUs, Sensor and Instrumentation Front-Ends, Embedded Data Acquisition Front-Ends, Consumer Appliance Control Panels.
Industrial Automation Controllers
The PIC16LF877A-I/L is widely used as the central MCU in industrial automation controllers where sensor-rich inputs and reliable field-serviceable assembly are required. Its 33 I/O, 8-channel 10-bit ADC, and integrated USART, SPI, and I2C peripherals let a single chip interface to digital sensors, motor drivers, and RS-485 multi-drop networks without external glue logic. The 2.5V to 5.5V operating range supports 24V industrial rails stepped down to 5V or 3.3V with low dropout. Compared to discrete logic implementations, the PIC16LF877A reduces BOM by approximately 60% and supports in-field firmware updates via ICSP, simplifying maintenance.
Empfohlen
HVAC Control Boards
The PIC16LF877A-I/L suits HVAC control boards that combine analog temperature sensing with PWM fan and valve control. Its 8-channel 10-bit ADC reads thermistors, pressure transducers, and airflow sensors directly; the two CCP/PWM modules drive proportional valves and triac-fired fans with up to 10-bit duty resolution at 10 MHz. EEPROM (256 bytes) holds user-configured setpoints across power cycles, and the 256-byte EEPROM endurance of 1M erase/write cycles per Microchip datasheet DS39582C is sufficient for years of runtime logging. The industrial -40C to +85C range covers attic and outdoor HVAC environments.
Empfohlen
Automotive Body and Interior ECUs
The PIC16LF877A-I/L is well suited for automotive body and interior ECUs, including mirror controllers, seat memory modules, lighting controllers, and HVAC head units. Its 33 I/O accept 12V battery inputs via external resistor dividers; the 10-bit ADC monitors switch and sensor states with adequate resolution. Compared to bare logic implementations, the PIC16LF877A replaces 4 to 6 logic ICs and runs at 10 MHz for sub-millisecond response to LIN/CAN-style message handling via the integrated USART. Designers building production automotive should evaluate the AEC-Q100 qualified PIC16F877A-I/L family variants for under-hood use.
Empfohlen
Sensor and Instrumentation Front-Ends
The PIC16LF877A-I/L serves as the data-acquisition front end in laboratory instruments and portable data loggers, where 8 ADC channels and 14 KB Flash enable on-board calibration tables and per-channel linearization. The 10-bit ADC delivers 1 mV resolution at full 5V scale, sufficient for bridge sensors, strain gauges, and thermistor conditioning. Compared to off-the-shelf data-acquisition modules, the PIC16LF877A integrates capture, processing, and USB/UART output in a single 44-PLCC footprint, saving PCB area. ICSP lets end-users update calibration coefficients in the field without opening the enclosure.
Empfohlen
Embedded Data Acquisition Front-Ends
The PIC16LF877A-I/L is used as a low-cost embedded data-acquisition front end for IoT gateway nodes and remote telemetry units. Its USART paired with a MAX485 or similar transceiver provides RS-485 multi-drop acquisition at up to 1 Mbps in 8-bit asynchronous mode; SPI and I2C connect to peripheral sensor ASICs. The 256-byte EEPROM is rated for 1M cycles per Microchip datasheet DS39582C, enough for a year of once-per-second sample-rate parameter logging. The wide 2.5V-5.5V supply range suits solar-powered remote installations where the rail fluctuates with irradiance.
Empfohlen
Consumer Appliance Control Panels
The PIC16LF877A-I/L drives consumer appliance control panels, including washing machines, dishwashers, and microwave ovens. Its 33 I/O accommodate keypad scanning, LCD multiplexing, relay driver controls, and buzzer/tone generation via CCP/PWM. The 14 KB Flash supports multi-language UI strings and look-up tables for sensor calibration; the 256-byte EEPROM retains user presets through power loss. Compared to discrete 8051 designs, the PIC16LF877A's single-cycle RISC architecture improves interrupt response time by approximately 4x, ideal for safety-critical door-lock and motor-overcurrent handling.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PIC16LF877A-I/L – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PIC16F877A-I/L | PIC16LF874A-I/L | PIC16F877AT-I/L | PIC16LF877A-I/PT | PIC16LF877AT-I/PT |
|---|---|---|---|---|---|---|
| Package | 44-PLCC (16.59x16.59 mm) | 44-PLCC - same | 44-PLCC - same | 44-PLCC - same | 44-PLCC - same | 44-PLCC - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory | 14 KB Flash | 14 KB Flash | 7 KB Flash (-50%) | 14 KB Flash | 14 KB Flash | 14 KB Flash |
| Operating Voltage | 2.5 V to 5.5 V (LF) | 4.0 V to 5.5 V (F) | 2.5 V to 5.5 V (LF) | 4.0 V to 5.5 V (F) | 2.5 V to 5.5 V (LF) | 2.5 V to 5.5 V (LF) |
| RAM | 368 bytes | 368 bytes | 192 bytes (-48%) | 368 bytes | 368 bytes | 368 bytes |
| EEPROM | 256 bytes | 256 bytes | 128 bytes (-50%) | 256 bytes | 256 bytes | 256 bytes |
| Max CPU Frequency | 10 MHz | 10 MHz | 10 MHz | 10 MHz | 10 MHz | 10 MHz |
| I/O Pins | 33 | 33 | 33 | 33 | 33 | 33 |
| Packaging Format | Tube | Tube | Tube | Tape & Reel | Tape & Reel | Tape & Reel |
Wichtigste Unterscheidungsmerkmale
- Extended low-voltage 2.5V to 5.5V operating range (vs. PIC16F877A-I/L)
- 44-PLCC socketable package with industrial -40C to +85C rating (vs. PIC16LF877A-I/P (DIP))
- 33 I/O and full peripheral set at 10 MHz (vs. PIC16LF874A-I/L)
Designhinweise
Estimated: PIC16LF877A at 10 MHz and 5 V draws approximately 7-15 mA active. Add a 100 nF ceramic decoupling capacitor directly between pins 11-12 (VDD-VSS) and another between pins 31-32, plus a bulk 10-100 uF tantalum or aluminum on AVDD/VSS pair to keep ADC references stable. Unused analog inputs (ANx) MUST be tied to VSS to minimize ADC shoot-through current; leaving them floating adds approximately 1-2 uA per pin according to Microchip datasheet DS39582C.
Keep the analog traces (AN0-AN7) short and away from the parallel slave port data lines (RD0-RD7/PSP0-PSP7) to minimize ADC sampling noise; use a guard ring tied to analog ground around the ADC pins. Place the 10 MHz crystal at OSC1/OSC2 within 8 mm of the pins and route the traces over a continuous ground pour. If using a parallel slave port, dedicate RD0-RD7 to data only and avoid running high-current signals on adjacent pins.
Configuration word settings vary between PIC16F877A and PIC16LF877A - the LF variant's oscillator configuration is calibrated for 2.5V operation and may misbehave if a 5V-only configuration word is loaded. Brown-out reset (BOR) should be enabled to protect EEPROM at low supply voltages; failure to do so can corrupt data at VDD transients. The MCLR pin MUST be either pulled high through a 10k resistor or used for ICSP; never leave MCLR floating as this triggers spurious resets.
Compliance-Informationen
Verified data does not specify RoHS, REACH, lead-free, halogen-free, or conflict-minerals compliance status. Per Microchip product page, the PIC16F877A family includes -L (lead-bearing PLCC) and -PT (lead-free TQFP) variants; check Microchip RoHS/REACH declarations at microchip.com for definitive compliance data.
