PIC18F45K80T-I/PT - 8-bit 64MHz MCU 32KB Flash ECAN 44-TQFP
Teilenummer: PIC18F45K80T-I/PT ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $5.42 | $5,42 |
| 10 | $4.88 | $48,80 |
| 100 | $4.35 | $435,00 |
| 500 | $3.79 | $1.895,00 |
| 1.000 | $3.32 | $3.320,00 |
PIC18F45K80T-I/PT Übersicht
Key features include a 64MHz internal oscillator, 35 digital I/O pins, 3.6KB of SRAM data memory, 1KB of EEPROM, a 12-bit ADC with Charge Time Measurement Unit (CTMU), and an operating voltage range of 1.8V to 5.5V. The device executes instructions at 16 MIPS (Million Instructions Per Second) under typical conditions.
The PIC18F45K80 belongs to Microchip's PIC18 XLP 18K family, which is a subfamily of 8-bit microcontrollers within the broader PIC microcontroller taxonomy (PIC microcontroller -> MCU -> microprocessor -> semiconductor). The XLP designation indicates nanoWatt technology with sleep currents measured in nanoamps, making this family well-suited to battery-powered and energy-harvesting designs. The integrated ECAN module supports CAN 2.0B with six programmable receive/transmit buffers and three dedicated transmit buffers, eliminating the need for an external CAN controller in automotive and industrial networked applications.
Typical applications include automotive body and chassis ECAN nodes, building climate and elevator controllers, industrial sensor nodes, and battery-powered remote monitoring with CAN connectivity. The 1.8V minimum supply voltage allows operation directly from a single lithium cell across most of its discharge curve, while 5.5V tolerance supports industrial 5V rails.
Designers should note that the PIC18F45K80T-I/PT is the tape-and-reel (T) and industrial temperature (-I/-40C to +85C) variant. Pin-compatible family members with different flash densities, temperature grades, and packaging options are available for cost optimization. The microcontroller requires MPLAB X IDE and a compatible programmer such as PICkit or ICD for firmware development.
Drop-in-Alternativen für PIC18F45K80T-I/PT – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit PIC18F45K80T-I/PT (gleiche Bauform und Footprint) – abweichend in Package, ADC, Timers, Program Memory (Flash), CTMU.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
PIC18F45K80-I/PT
✅ Drop-In✓ Auf Lager
$2.4 / Stück
Datenblatt ansehen →PIC18F46K80-I/PT
✅ Drop-In✓ Auf Lager
$4.21 / Stück
Datenblatt ansehen →PIC18F45K80-H/PT
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$4.95 / Stück
Datenblatt ansehen →PIC18F45K80-E/PT
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$2.78 / Stück
Datenblatt ansehen →PIC18F45K80T-I/PT Grenzwerte & elektrische Eigenschaften
| Core Processor | PIC18 |
| Core Size | 8-bit |
| Maximum CPU Frequency | 64 MHz |
| Instruction Throughput | 16 MIPS |
| Program Memory (Flash) | 32 KB (16K x 16) |
| RAM Size | 3.6 KB (3648 bytes) |
| EEPROM Size | 1 KB (1024 bytes) |
| Number of I/O Pins | 35 |
| Supply Voltage (VDD) | 1.8 V to 5.5 V |
| ADC | 12-bit, multi-channel with CTMU |
| Communication Interfaces | ECAN, I2C, SPI, UART (EUSART) |
| ECAN Module | CAN 2.0B, 6 RX / 3 TX buffers |
| Gehäuse | 44-pin TQFP (PT), 10x10 mm |
| Betriebstemperaturbereich | -40 C to +85 C (Industrial) |
| Montageart | Surface Mount |
| Packaging | Tape & Reel (T suffix) |
| Oscillator Type | Internal |
| Technology | nanoWatt XLP (eXtreme Low Power) |
| RoHS-Status | ROHS3 Compliant |
PIC18F45K80T-I/PT Pin-Konfiguration
| Pin 1 | RH2/AN12 — I/O port RH2, analog input 12 |
| Pin 2 | RH3/AN13/CCP2 — I/O port RH3, analog input 13, CCP2 |
| Pin 3 | RE0/PWM2/AN5 — I/O port RE0, PWM2, analog input 5 |
| Pin 4 | RE1/PWM3/AN6 — I/O port RE1, PWM3, analog input 6 |
| Pin 5 | RE2/PWM4/AN7 — I/O port RE2, PWM4, analog input 7 |
| Pin 6 | VDD — Positive supply voltage |
| Pin 7 | VSS — Ground reference |
| Pin 8 | OSC1/RA7 — External oscillator input / port RA7 |
| Pin 9 | OSC2/RA6 — External oscillator output / port RA6 |
| Pin 10 | RC0/SOSCO — I/O port RC0, secondary oscillator output |
| Pin 11 | RC1/SOSCI — I/O port RC1, secondary oscillator input |
| Pin 12 | RC2/CCP1 — I/O port RC2, CCP1 |
| Pin 13 | RC3/SCL — I/O port RC3, I2C clock |
| Pin 14 | RC4/SDA — I/O port RC4, I2C data |
| Pin 15 | RC5/SDO — I/O port RC5, SPI data out |
| Pin 16 | RC6/TX/CK — I/O port RC6, EUSART TX/CK |
| Pin 17 | RC7/RX/DT — I/O port RC7, EUSART RX/DT |
| Pin 18 | VSS — Ground reference |
| Pin 19 | VDD — Positive supply voltage |
| Pin 20 | RB0/INT0/FLT0 — I/O port RB0, external interrupt 0 |
| Pin 21 | RB1/INT1 — I/O port RB1, external interrupt 1 |
| Pin 22 | RB2/INT2 — I/O port RB2, external interrupt 2 |
| Pin 23 | RB3/INT3 — I/O port RB3, external interrupt 3 |
| Pin 24 | RB4/KBI0 — I/O port RB4, keyboard interrupt 0 |
| Pin 25 | RB5/KBI1 — I/O port RB5, keyboard interrupt 1 |
| Pin 26 | RB6/KBI2/PGC — I/O port RB6, keyboard interrupt 2, ICSP clock |
| Pin 27 | RB7/KBI3/PGD — I/O port RB7, keyboard interrupt 3, ICSP data |
| Pin 28 | RD0/PSP0/C1IN+ — I/O port RD0, comparator 1 input + |
| Pin 29 | RD1/PSP1/C1IN- — I/O port RD1, comparator 1 input - |
| Pin 30 | RD2/PSP2/C2IN+ — I/O port RD2, comparator 2 input + |
| Pin 31 | RD3/PSP3/C2IN- — I/O port RD3, comparator 2 input - |
| Pin 32 | C1OUT — Comparator 1 output |
| Pin 33 | C2OUT — Comparator 2 output |
| Pin 34 | RD4 — I/O port RD4 |
| Pin 35 | RD5 — I/O port RD5 |
| Pin 36 | RD6 — I/O port RD6 |
| Pin 37 | RD7 — I/O port RD7 |
| Pin 38 | VSS — Ground reference |
| Pin 39 | VDD — Positive supply voltage |
| Pin 40 | RA0/AN0/C1IN+ — I/O port RA0, analog input 0 |
| Pin 41 | RA1/AN1/C2IN+ — I/O port RA1, analog input 1 |
| Pin 42 | RA2/AN2/C2IN-/CVREF — I/O port RA2, analog input 2 |
| Pin 43 | RA3/AN3/VREF+ — I/O port RA3, analog input 3, VREF+ |
| Pin 44 | RA5/AN4/SS — I/O port RA5, analog input 4, SPI slave select |
Typische Anwendungen
PIC18F45K80T-I/PT ist geeignet für 6 Anwendungs: Automotive ECAN Body Control Module, Building Automation HVAC Controller, Industrial Elevator Control, Battery-Powered Remote Sensor Node, Medical Patient Monitoring Peripheral, CAN-Based Industrial Sensor Hub.
Automotive ECAN Body Control Module
The PIC18F45K80T-I/PT is purpose-built for in-vehicle network nodes because it integrates an Enhanced CAN module supporting CAN 2.0B with six receive buffers and three transmit buffers, removing the need for an external CAN controller IC. At 64MHz / 16 MIPS, the part easily handles CAN message scheduling, sensor fusion at 100Hz, and the LIN-to-CAN gateway logic typical of door, seat, and mirror modules. The 1.8V-5.5V range tolerates 12V automotive rail transients when paired with a TVS clamp, and nanoWatt XLP sleep current under 100nA preserves battery life during key-off. The 44-TQFP footprint is industry-standard and direct-RC-solder-friendly for prototype build.
Empfohlen
Building Automation HVAC Controller
The PIC18F45K80T-I/PT's 12-bit ADC with integrated CTMU is ideal for HVAC sensor nodes that measure temperature, humidity, and pressure with high linearity over wide operating ranges. The 35 I/O pins interface directly with relay drivers, TRIAC controllers, and 4-20mA loops without a serial expander. nanoWatt XLP lets the controller sleep at nanoamp currents between sensor reads, dramatically reducing building energy waste. The 5.5V tolerance aligns with 24V industrial HVAC control boards when used with a downstream regulator. Internal 64MHz oscillator eliminates external crystals, cutting BOM cost for high-volume commercial thermostat deployments.
Empfohlen
Industrial Elevator Control
Elevator dispatch and door control demand deterministic response times and CAN bus connectivity, both of which the PIC18F45K80T-I/PT delivers through its ECAN module and 16 MIPS throughput. The 32KB Flash accommodates state-machine firmware for call logic, anti-trap algorithms, and fault logging. The industrial temperature range (-40C to +85C) handles unconditioned machine rooms, and the TQFP-44 package is rated for vibration-heavy motor rooms. The CTMU enables touch-button capacitive sensing without additional ASICs, simplifying the user panel design. Self-programmable flash supports in-field firmware updates over the service bus.
Empfohlen
Battery-Powered Remote Sensor Node
Battery-powered wireless sensor nodes benefit from the PIC18F45K80T-I/PT's nanoWatt XLP technology, which achieves sub-100nA sleep current allowing years of operation from a single AA lithium cell. The 1.8V minimum VDD lets the part run directly from a nearly-discharged battery, while the 64MHz active mode wakes the part only when sensor data must be transmitted. The 12-bit ADC plus CTMU supports accurate ratiometric measurements on thermistors and resistive bridges. Integrated ECAN, while underutilized in purely wireless nodes, provides a wired commissioning interface for factory calibration without removing the device from service.
Empfohlen
Medical Patient Monitoring Peripheral
For non-life-critical medical peripherals such as infusion pump displays, therapy timers, and bedside sensors, the PIC18F45K80T-I/PT provides the reliability of PIC18 silicon with integrated ECAN for connectivity to bedside monitoring hubs. The 12-bit ADC digitizes analog physiological signals with sufficient resolution for trend monitoring, while the CTMU enables accurate touch-panel sensing for caregiver input. The nanoWatt XLP sleep mode is essential for battery-backed devices that must remain operational during patient transport. Pin-compatible family members allow easy migration to the PIC18F46K80-I/PT if firmware exceeds 32KB.
Empfohlen
CAN-Based Industrial Sensor Hub
Multi-sensor industrial hubs leverage the PIC18F45K80T-I/PT's 35 I/O count to interface with multiple analog and digital sensors while publishing aggregated data over ECAN to a PLC. The 64MHz speed handles the polling, averaging, and CAN frame assembly within the typical 10ms cycle time required for process control. Industrial temperature tolerance and TQFP-44 vibration-resistant package suit plant floor deployment. Self-programmable flash lets OEMs push sensor calibration updates over the same CAN bus used for process data, avoiding field service calls and reducing total cost of ownership.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PIC18F45K80T-I/PT – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PIC18F45K80-I/PT | PIC18F46K80-I/PT | PIC18F45K80-H/PT | PIC18F45K80-E/PT |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-TQFP (10x10) | 44-TQFP (10x10) - same | 44-TQFP (10x10) - same | 44-TQFP (10x10) - same | 44-TQFP (10x10) - same |
| Flash Memory | 32 KB | 32 KB | 64 KB | 32 KB | 32 KB |
| RAM Size | 3.6 KB | 3.6 KB | 3.6 KB | 3.6 KB | 3.6 KB |
| EEPROM | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB |
| Maximum Frequency | 64 MHz | 64 MHz | 64 MHz | 64 MHz | 64 MHz |
| ECAN Module | Yes (2.0B) | Yes (2.0B) | Yes (2.0B) | Yes (2.0B) | Yes (2.0B) |
| Temperature Range | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +150C (High-temp) | -40C to +125C (Automotive E) |
Wichtigste Unterscheidungsmerkmale
- Higher flash density in same footprint (vs. PIC18F45K80-I/PT)
- Higher temperature grade option (vs. PIC18F45K80-H/PT)
- Lower unit price than automotive-qualified variant (vs. PIC18F45K80T-I/PTVAO)
Designhinweise
Decouple VDD with a 100nF ceramic capacitor placed within 5mm of each VDD/VSS pair on the 44-TQFP package, plus a single bulk 10uF tantalum or ceramic at the chip's main VDD pin. For noise-sensitive ECAN nodes add a ferrite bead in series with VDD and a second 100nF decoupling cap on the analog supply (AVDD). The 1.8V minimum VDD lets the PIC18F45K80T-I/PT run directly from a single lithium cell - but ensure VDD rise time is less than the datasheet-specified maximum to guarantee a clean Power-on Reset.
Place the ICSP (In-Circuit Serial Programming) pins RB6/PGC and RB7/PGD on accessible test pads or a 2x3 0.1-inch header for in-field firmware updates. Route the ECAN TX/RX traces to the MCP2551 (or equivalent) CANH/CANL pins as a 120-ohm terminated differential pair with characteristic impedance of 120 ohms and length matching within 5mm. The 44-TQFP footprint exposes the die pad as GND; solder it to a large copper pour for thermal dissipation and ground integrity.
The PIC18F45K80T-I/PT's -I temperature grade is -40C to +85C; do not specify this part for underhood or industrial furnace environments - use the -E (-40C to +125C) or -H (-40C to +150C) variants instead. The internal oscillator is factory-trimmed but can drift up to 5% across temperature; for CAN timing-critical applications use an external 16MHz or 20MHz crystal with the HS-PLL configuration. Avoid driving ECAN with software bit-banging - always use the dedicated ECAN peripheral to ensure CAN 2.0B timing compliance.
Compliance-Informationen
ROHS3 Compliant per Microchip product page and microchipusa listing. Standard -I grade is not AEC-Q100 qualified; the Varnish Automotive Qualified (VAO) suffix variant is available for AEC-Q100 applications.