PIC18F8390-E/PT - 8KB Flash LCD MCU, 80-Pin TQFP | Microchip
Teilenummer: PIC18F8390-E/PT ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $9.5 | $9,50 |
| 10 | $8.75 | $87,50 |
| 100 | $7.9 | $790,00 |
| 500 | $7.1 | $3.550,00 |
| 1.000 | $6.5 | $6.500,00 |
PIC18F8390-E/PT Übersicht
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and peripherals such as timers, communication interfaces, and analog blocks. The PIC18 family belongs to Microchip's 8-bit RISC architecture with C-compiler-optimized instruction set. PIC18F devices specifically add hardware multiply and a 16-bit wide instruction path for higher code density than the baseline PIC16 family. The integrated LCD driver eliminates the need for an external segment-driver IC in low-to-medium display count HMI designs.
Key features include 8 KB flash program memory with self-programming support, 768 bytes of RAM, integrated LCD driver for glass displays, nanoWatt Technology for low-power sleep and idle modes, 66 I/O pins, 10 MIPS performance at 3V operation, and a wide operating temperature range suited for industrial environments. The LCD peripheral supports up to 48 segments, enabling segment-rich HMIs without external driver chips.
The part uses Microchip's enhanced PIC18 RISC core with a Harvard bus architecture and C-compiler-optimized instruction set, executing most instructions in one cycle. Integrated peripherals include ADC, timers, USART, MSSP (SPI/I2C), and the LCD segment driver, allowing direct connection to common HMI hardware and minimizing external component count.
Typical applications include handheld meters, thermostats, home security panels, and power/gas/water metering end products. The combination of integrated LCD driver and nanoWatt low-power modes makes the device particularly attractive for battery-powered metering where segment displays are common.
Designers should note that the E suffix indicates the -40C to +125C extended temperature grade, and the /PT suffix denotes the 80-pin TQFP package supplied in tray. Use MPLAB X IDE with the XC8 compiler for development.
This page synthesizes distributor pricing from LCSC and Mouser, drop-in same-package alternatives from the PIC18F family, and practical design notes not found in the manufacturer datasheet.
Drop-in-Alternativen für PIC18F8390-E/PT – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit PIC18F8390-E/PT (gleiche Bauform und Footprint) – abweichend in I/O Pins, Core Architecture, Package, Program Memory (Flash), ADC.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
PIC18F8490-E/PT
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$6.55 / Stück
Datenblatt ansehen →PIC18F6490-E/PT
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
PIC18F6390-E/PT
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$3.4 / Stück
Datenblatt ansehen →PIC18F6722-I/PT
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$5.32 / Stück
Datenblatt ansehen →PIC18F8722-I/PT
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$6.5 / Stück
Datenblatt ansehen →PIC18F8390-E/PT Grenzwerte & elektrische Eigenschaften
| Core Architecture | PIC18 8-bit RISC |
| Program Memory (Flash) | 8 KB |
| Data Memory (RAM) | 768 bytes |
| Operating Voltage | 5 V (typical) |
| Maximum CPU Performance | 10 MIPS |
| I/O Pins | 66 |
| Gehäuse | 80-pin TQFP (PT), Tray |
| Montageart | Surface Mount |
| Integrated LCD Driver | Yes (up to 48 segments) |
| Low-Power Technology | nanoWatt Technology |
| Betriebstemperatur | -40C to +125C (Extended, E suffix) |
| Family | PIC18F6390/6490/8390/8490 |
| RoHS-Status | Compliant |
PIC18F8390-E/PT Pin-Konfiguration
| Pin 1 | SEG0 — LCD segment output / digital I/O |
| Pin 10 | SEG9 — LCD segment output / digital I/O |
| Pin 20 | RB0/FLT0 — PORTB I/O / PWM fault input |
| Pin 30 | RC0/T1OSO — PORTC I/O / Timer1 oscillator output |
| Pin 40 | RD7/PSP7 — PORTD I/O / Parallel Slave Port data bit 7 |
| Pin 50 | RE0/RD — PORTE I/O / parallel port read control |
| Pin 60 | SEG24 — LCD segment output 24 |
| Pin 70 | COM3 — LCD common driver output 3 |
| Pin 80 | VDD — Positive power supply |
Typische Anwendungen
PIC18F8390-E/PT ist geeignet für 6 Anwendungs: Electric Power Meter with LCD Display, Programmable Thermostat, Home Security Control Panel, Gas and Water Metering Endpoints, Industrial Handheld Meter / Multimeter, HVAC Remote Control / Thermostat Transmitter.
Electric Power Meter with LCD Display
The PIC18F8390-E/PT is purpose-built for single-phase or multi-function electricity meters requiring segment LCD readouts. Its integrated LCD segment driver eliminates the need for an external HT1621-style driver IC, reducing BOM cost by $0.30-$0.50 per board. With 8 KB flash and 768 bytes RAM, the device supports energy accumulation algorithms, calibration tables, and tariff scheduling typical of residential smart meters. The nanoWatt idle/sleep modes drop quiescent current to microamp levels during LCD hold-display states, critical for battery-backed or CT-powered meter designs where the IC must retain time-of-use data without external supply.
Empfohlen
Programmable Thermostat
Wall-mounted programmable thermostats use the PIC18F8390-E/PT to drive a 30-48 segment LCD showing setpoint, mode, and schedule icons. The 66 I/O pins are sufficient for keypad scanning, temperature sensor (NTC or digital) interface via I2C, and HVAC relay control outputs. The extended -40C to +125C operating range handles outdoor-wall installation thermal swings. The 10 MIPS performance at 3V executes PID control loops and schedule logic with headroom, while nanoWatt modes drop consumption during backlight-off periods to extend backup battery life during power outages.
Empfohlen
Home Security Control Panel
Home security panels with segment LCD keypads benefit from the PIC18F8390-E/PT's combination of I/O count, LCD driver, and low-power modes. The MCU scans up to 16-zone alarm inputs, drives the LCD status display showing armed/disarmed/bypass states, and handles siren/communicator outputs. The flash self-programmability enables field firmware updates for protocol changes (contact ID, SIA). nanoWatt sleep drops panel standby below 50 uA, preserving backup battery capacity during AC mains failures that may last 24 hours.
Empfohlen
Gas and Water Metering Endpoints
Battery-powered gas and water meter endpoints use the PIC18F8390-E/PT for pulse counting, segment LCD consumption display, and AMR (automatic meter reading) interface. The integrated LCD driver shows cumulative cubic-feet/liters, leak detection flags, and battery gauge without external components. nanoWatt Technology enables 10+ year battery life by sleeping at sub-microamp current between sensor samples. The wide temperature range supports outdoor meter installations and underground vault deployment.
Empfohlen
Industrial Handheld Meter / Multimeter
Handheld digital multimeters and clamp meters use the PIC18F8390-E/PT for range selection, ADC conversion control, segment LCD readout, and auto-power-off sequencing. The 10 MIPS performance executes RMS calculation and autoranging algorithms. The integrated LCD driver directly connects to 3.5-digit or 4-digit 7-segment style LCDs. Extended -40C to +125C operation handles the temperature gradients inside handheld enclosures during continuous use.
Empfohlen
HVAC Remote Control / Thermostat Transmitter
Wireless thermostats and HVAC remote transmitters pair the PIC18F8390-E/PT with sub-GHz RF modules for setpoint transmission. The MCU handles segment LCD display, button matrix, RF packet formatting, and sleep/wake duty cycling. nanoWait modes are critical for 6-12 month battery life on AAA cells. The wide temperature range supports both indoor climate zones and garage/workshop transmitter placement.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PIC18F8390-E/PT – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PIC18F8490-E/PT | PIC18F6490-E/PT | PIC18F6390-E/PT | PIC18F6722-I/PT | PIC18F8722-I/PT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TQFP-80 (PT) | TQFP-80 (PT) - same | TQFP-64 (PT) - different | TQFP-64 (PT) - different | TQFP-80 (PT) - same | TQFP-80 (PT) - same |
| Flash Memory | 8 KB | 16 KB | 8 KB | 4 KB | 128 KB | 128 KB |
| RAM | 768 bytes | 768 bytes | 768 bytes | 768 bytes | 3,936 bytes | 3,936 bytes |
| I/O Pins | 66 | 66 | 54 | 54 | 68 | 70 |
| Integrated LCD Driver | Yes (48 segments) | Yes (48 segments) | Yes | Yes | No | Yes |
| Operating Temperature | -40C to +125C (Extended) | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +85C (Industrial) | -40C to +85C (Industrial) |
| Performance | 10 MIPS @ 3V | 10 MIPS | 10 MIPS | 10 MIPS | 10 MIPS | 10 MIPS |
Wichtigste Unterscheidungsmerkmale
- Integrated LCD segment driver eliminates external HT1621-style driver IC (vs. PIC18F6722-I/PT)
- Extended -40C to +125C operating temperature vs industrial grade alternatives (vs. PIC18F6722-I/PT)
- 8 KB flash matches typical metering firmware footprint without over-provisioning (vs. PIC18F8722-I/PT)
Designhinweise
Place the 80-pin TQFP decoupling capacitor (typically 100 nF ceramic + 10 uF bulk) within 5 mm of the VDD/VDDCORE pin pair. The PIC18F8390-E/PT has multiple VDD and VSS pins distributed around the package; each must have a local 100 nF bypass. Use a 4-layer PCB with a dedicated ground plane for best EMC performance, especially since the integrated LCD driver generates AC bias voltages that can couple to analog or sensitive digital signals.
Do not confuse the PIC18F8390 with the PIC18F8722 when ordering - both share the 80-pin TQFP package but the 8722 has 128 KB flash vs 8 KB. The E suffix indicates extended -40C to +125C temperature; the I suffix indicates -40C to +85C industrial. Verify the suffix matches your deployment environment. Also note that 80-pin TQFP PIC18 LCD parts share pinout with each other (8390/8490/8722) but NOT with 64-pin variants - migrating from TQFP-80 to TQFP-64 requires board redesign.
Configure nanoWatt idle/sleep modes by setting the IDLEN, SCS, and IDLEN bits in the OSCCON register before entering Sleep. The LCD driver can continue operating in Sleep mode via the RTCC timer, allowing the display to remain active while MCU current drops below 5 uA. For battery-backed metering applications, ensure the LCD bias voltages remain within the LCD-charge-pump specifications in DS39760 chapter 18.
Compliance-Informationen
RoHS and REACH compliant per Microchip product documentation. AEC-Q100 not qualified - not marketed as automotive grade.
